Search Documents

By D. Hodouin

The paper reviews approaches to estimate in a real time fashion consistent mass flowrates and assays, using data from the on-stream analyzers and flowmeters of a flotation circuit. Results obtained with one algorithm operating on-line with an industrial flotation circuit are presented.

Jan 1, 1996

By P. A. Schmitz

The characteristics of gold leaching from carbonaceous matter by sodium cyanide, and sorption of gold cyanide to carbonaceous matter in autoclaved and non -autoclaved gold ore from Barrick Goldstrike Mines Inc. (BGMI), Nevada, was investigated. Much greater gold cyanide complex sorption was observed for the carbonaceous matter in high preg-robbing ores relative to the low preg-robbing ores. This observation corroborates previous reports that have attributed observed preg-robbing behavior to the carbon in the ore. Gold cyanide complex sorption was found to be reversible for carbonaceous matter from low preg-robbing ore, but was irreversible for carbonaceous matter from high preg-robbing ores. Autoclaving the ore appeared to enhance the sorptive behavior of the carbonaceous matter from both high and low preg-robbing ores.

Jan 1, 1999

By S. D. F. Rocha, A. L. A. SANTOS, E. M. A. BECHELENI, R. M. Papini, P. R. M. Viana, F. P. C. Silvas

The kinetics of atmospheric sulfuric acid leaching from a Brazilian nickel laterite ore was assessed using distinct reducing agents and ore mineralogy. This transitional ore contains 1.63% Ni distributed as 1.27% in coarse size (− 500 + 150 μm), mainly as silicates (lizardite and chlorite—28.6%), and 2.06%in the fines fraction (− 75 μm), mainly as iron oxy-hydroxides (goethite and hematite—49%). The effects of temperature, acid concentration, reducing reagent type, and concentration were evaluated. The − 75 μm fraction limited the leaching efficiency and the use of reducing media with thiosulfate improved leaching and Ni-Fe selectivity. However, at constant Eh of 626–743 mV and a pH range between 0.2 and 1.1, no substantial rise in metals extraction, except for Co and Mn, has been observed. In order to determine the process control at 95 °C, two regions in the extraction curves were used in combination with the shrinking core model. Control by porous diffusion was observed and the kinetic constant was found to be in the order kFe<kNi<kMn<kCo<kMg for atmospheric leaching without Eh control. In reducing media for the first 15 min of leaching, the kinetic constant was found to be kFe<kNi<kMg≅kCo<kMn as derived from Ni disseminated into iron oxides structures.

Oct 7, 2020

By H. W. Hitzrot

Introduction Mechanical classifiers consist of a settling tank with parallel sides and a sloping bottom equipped with a mechanism which continuously agitates the pulp and removes the settled solids. The functions served by mechanical classifiers include the following: (1) allow the particles larger than the desired size to settle in the tank and provide an overflow product with a minimum of oversize particles, (2) produce an overflow product of sufficiently high solids content to meet the requirements of the subsequent processing steps, (3) agitate the pulp and permit separation of the entrapped undersize particles so they can report in the overflow product, and (4) drain and remove the underflow solids from the settling pool. Various types of mechanisms have been used to agitate the pulp and remove the settled solids, which include: (I) endless belt and chain drags, (2) reciprocating rakes, (3) helical flights mounted on a rotating shaft which extends through the settling pool, (4) helical flights inside of a rotating drum which contains the classifier pool, (5) troughed conveyor belts forming the settling pool in the concave curve of the belt closely following the tail pulley, and (6) low-speed impellers agitating the underflow settled in the apex of cone-type mechanical classifiers.23 The principal use of mechanical classifiers has been in closed¬-circuit wet grinding; however, this application has been widely displaced over the past few decades by the hydrocyclone. The hydrocyclone installation, including its feed pump, offers lower capital costs and requires less floor space. Nominally it produces an overflow prod¬uct of higher solids content, compared with a mechanical classifier, for comparable classification size up to 400µm (35 mesh). However, these advantages of the hydrocyclone are being gained at the sacrifice of some of the advantages of the mechanical classifier. The mechanical classifier requires less power and has lower maintenance costs than the hydrocyclone and its feed pump. The underflow product from the mechanical classifier can have a higher solids content and contain less entrapped undersize particles than the comparable product from the hydrocyclone. Consequently, it is capable of operating at a higher classification efficiency. A reduced circulating load24, 25 results under these conditions in a closed-circuit grinding application. Other applications for mechanical classifiers include desliming, dewatering, and washing operations. Sand-slime separation may be achieved using one or more stages of mechanical classifiers. Typical applications would include washing and deslimining of concrete aggre¬gate or sand; glass sand; abrasives; oyster shells; phosphate rock; iron, nickel, and chromium ores; alumina; zeolites; solar salt; and precipitates from chemical processing. As an example for the latter, Bitzer26 recommended the use of mechanical classifiers for countercur¬rent cementation-in-pulp of copper from the leach liquor. Similarly, mechanical classifiers are used in uranium processing27 for separation of the barren sands from the pregnant leach solution. Depending on the particle size and the effectiveness of the sand¬slime separation, the sand product from mechanical classifiers may be drained to solids content approaching 84%. Thus, mechanical classifiers are frequently used as dewatering equipment for various applications, such as: 1) Make a product having suitable solids content for subsequent transport by belt conveyor. 2) Provide a drained product to reduce cost of drying. 3) Provide a drained, washed, heavy sand product for return to the circuit. 4) Recover fine values from dilute plant effluents from coal, sand, phosphate-rock, and iron-ore washing plants and from steel-mill flue¬dust scrubbers. 5) Drain residual reagents of a preceding process stage prior to conditioning with reagents of different characteristics, e.g., cationic¬anionic flotation of phosphate rock, iron ore, etc. Design and Operating Features The proper selection of mechanical classification equipment re¬quires that the properties of the solids and liquid are adequately de¬fined. The following descriptive information regarding the solids is desired: feed rate, chemical and physical composition, density, tem¬perature, size analysis, and desired separation size. For the liquid used, the following data would be needed: feed rate, density, viscosity, pH, and temperature. Settling Area. The pool area required to permit a particle larger than the separation size to settle depends on the density and shape of the particle and on the density and viscosity of the pulp within the classifier pool. These criteria of the solids and pulp determine the settling rate which, in turn, determines the settling area required. Determination of the settling rate by long-tube batch tests can be used to calculate the settling area. A theoretical approach for estimat¬ing the settling area requirements is discussed in Chapter 1, Classifica¬tion Theory. This procedure can be used when neither test data nor empirical data from similar operations are available. Data on settling-area requirements and settling rates have been compiled by the manufacturers of mechanical classifiers. The approxi¬mate settling area required for a particular separation size can be estimated by using the curve shown in Fig. 65. This curve applies for closed-circuit grinding applications. For dilute velocity classification in open circuit, desliming, the length of the overflow weir, W, multiplied by the weir&apos;s mean distance from the feed opening, E, is used as the design criterion, instead of the settling area, in sizing the classifier. The area requirements, W X E, for dilute velocity classification can be expressed in terms of volumetric flow, Q, and settling rate, Rs, as follows: W x E = Q/(18.06 Rs) where W and E are feet, Q is gallons per minute, and Rs is inches per second. Overflow Weir. The hydraulic head, and thus the velocity at which the overflow crests the overflow weir, is one of the factors controlling the particle size of classification. Consequently, the length of the overflow weir must be designed to provide the overflow velocity which allows the particles larger than the desired size of classification to settle in the working area of the pool. Obtaining the necessary

Jan 1, 1985

By Lauro Lacerda

Shotcrete is a highly adaptable and widely used underground construction material at infrastructure and mining projects around the world. In fact, many projects could not have been completed without its utilization. As underground projects became larger the use of mechanized wet-mix spraying gradually replaced manual dry-mix shotcrete applications. This paper details some of the reasons for that and provides information on the equipment and operational factors including safety and productivity required to successfully complete underground shotcrete projects.

Jun 13, 2021

By Trenton Cohen, Joseph McDivitt, Shimi Tzobery, Joseph Sinacori, Scott Zylstra

The 2-mile Beach Interceptor Sewer Tunnel was constructed in 1954 to then-current mining and construction standards. Due to its lifespan and deteriorating condition it is now being stabilized and rehabilitated using conventional excavation and ground support. At its southern end, below the prestigious Three Arch Bay community, the original tunnel alignment passes under a historic landslide where the tunnel was sand-backfilled and capped by bulkheads in 1957 due to severe and caving ground conditions. Video footage of the existing 21- inch clay pipe showed that the pipe is severely damaged, which could potentially cause a catastrophic pipeline failure and sewage spill into the Pacific Ocean. This paper summarizes the thorough investigation and design process, tunnel realignment construction and monitoring, and the notable cooperation between all parties to overcome the project risks.

Dec 1, 2022

By C. Basilio

Thermodynamic calculations based on a rigorous mass balance technique have been carried out for the chalcocite-potassium ethyl xanthate (KEX) system. The results of the calculations are used to: i) construct Eh-pH diagrams for KEX additions ranging from 0 to 10-4 M, ii) determine the amounts of cupric ions and copper xanthate formed at different Eh and pH values to make three-dimensional diagrams, and iii) determine the minimum KEX addition required to form CuX and CuX2.. This allows prediction of the optimum conditions for flotation and comparison of this with microflotation test data. In addition, voltammetry experiments have been conducted on chalcocite electrodes at pH 9.2 and pH 6.8 in order to gain information on the role of metastable species in flotation. On the basis of these experiments, possible reaction mechanisms are discussed and comparisons are made with what is expected on the basis of thermodynamics.

Jan 1, 1985

By A. W. Khair

This paper deals with the causes and mechanisms of pillar failure in a southern West Virginia coal mine. The conclusions are based on in-mine observations and analysis of mining methods, eyewitness account of the sequence of events, topographic and geologic conditions, and mechanical properties of mine roof, coal, and floor. The study indicated that massive pillar failure was caused by the collapse of the mine roof. The collapse of the mine roof was due to the combined effects of high lateral compressive stress and high extraction ratio causing excessive bending of the roof beyond its limit. It was assumed that the higher lateral compressive stress under such a shallow cover was probably due to the drastic change in the structural geology of the area and possible residual stresses. Eased on the analytical study it was concluded that the sudden release of elastic energy (shock) due to the rupture of the roof caused the squeezing of approximately eighty mine pillars.

Jan 1, 1983

By Howard E. Mitchell

Modern mechanical raise drilling was first introduced into the United states in 1962. This method of safely, economically raising a shaft has steadily increased in popularity since that time. This steady growth has been largely enhanced by the many advantages to be gained by mechanical raise drilling, as well as by the increasing reliability of the equipment required. It is the purpose of this paper to briefly review the state of the art of raise drilling to include: the various applications and advantages; the equipment requirements, including a comparison of the various types and sizes of machines and rock cutting equipment; equipment performance; and future trends.

Jan 1, 1978

By J. E. Murphy, Y. Topkaya, R. E. Johnson, B. R. Palmer, D. K. Dysinger, R. B. Bhappu, A. E. Clark

The U.S. Bureau of Mines utilized a central composite experimental design to investigate leaching kinetics of pure chalcopyrite in the sulfuric acid-oxygen system. The six factors studied were oxygen pressures of 150, 300 and 450 PSI, leach temperatures of 35O, 65O, and 95O C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0 and 1.5, leach times of 8, 16 and 24 hours, initial acid strengths of 0.6, 1.2 and 1.8 g H,SO,/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. Chemical analysis and oxygen consumption measurements indicatedthat leaching occurs through three consecutive reactions. Temperature was the primary determinant of leach rate and solution acidity was the primary determinant of oxygen consumption, sulfur oxidation, and activation energy.

Jan 1, 1993

By Chris Roos

The mining industry has made strides in planning for operations to be safe for the workforce and public, to protect the natural environment, and to maximize value for shareholders. However, many of the techniques used to accomplish these goals are based on estimated models of mineral content, production efficiency, and economic performance. The industry has begun to recognize the need for understanding the uncertainty in these models, how it affects their decisions, and what the potential impacts are for each project. The challenge has become how technical professionals can effectively communicate the impact of this uncertainty and its importance to both technical and non-technical audiences. This paper presents mining engineers (and other technical professionals) with traditional and modern principles of data visualization and technical communication that can assist with communicating the effects of uncertainty in the mine planning process.

Jun 25, 2023

By Courtney Chamberlain

The Telfer Project, Australia&apos;s newest, largest and most remote gold mine, treats 480,000 metric tonnes of ore grading 9.33 grams per tonne derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded using a continuous strake, table and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, CCD and stellar filters for clarification and precipitate removal. Overall recovery into bullion averages 98 percent. The mill incorporates a number of design features which allow for maximum efficiency and security using a minimum number of operating personnel.

Jan 1, 1980

By P. K. Songfack

The transport of slurry within the ball mill depends on the peripheral velocity and porosity of the ball charge. Residence time distribution and mill hold up are of-ten used as indicators of the mode of transport. In this work, the transport problem is tackled via direct simulation of the three dimensional motion of the ball charge. In doing so, the following quantities are calculated: (i) ball size distribution as a function of the distance from the feed end of the mill (ii) mean peripheral and longitudinal velocity and longitudinal velocity of balls of different sizes, and (iii) the spatial distribution of porosity within the ball charge. Hence, the problem of transport is handled as a motion of part of the slurry with the ball charge and part as hydrodynamic flow through the porous structure.

Jan 1, 1993

By J. P. Matoney

In recent years, the diminishing supply of natural gas has led energy suppliers and consumers to consider making synthetic natural gas from coal. A number of processes have been devised to produce gas from coal; many of these have been operated at the pilot stage and some have been operated commercially. Each process has specific coal feed stock requirements with respect to size consist and moisture content. The purpose of this presentation is to compare the estimated costs for coal handling, live storage, size reduction and drying facilities that would be required for delivery of coal feedstock to different gasification processes.

Jan 1, 1977

By R. M. Enick

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. The separation, conducted at ambient temperature and a pressure of about 1000 psi a, was based on the difference in wettability of precious metals and minerals. Contact angle results indicated that in the presence of water and liquid CO2, gold, platinum and silver had intermediate wettability. Minerals such as quartz and magnetite, however, were hydrophilic. Therefore fine gold particles. -325 mesh, that were mixed with water and liquid CO2 dispersed in the CO2 or agglomerated at the H2O-CO2 interface while the minerals tended to remain in the aqueous phase. Best results were obtained when these fine gold particles were liberated, were not agglomerated in slimes, were not adhering to minerals, and were not coated with minerals.

Jan 1, 1998

By John H. Canterford

The adsorption of uranium onto Wyoming bentonite was measured in carbonate media over the range pH 8-11. Uranium was removed from solution onto the solids by a rapid reaction, proposed to be adsorption of the anionic uranyl tricarbonato complex onto edges of the clay platelets, and a slow reaction which may be precipitation of a hydroxide. The changes in uranium content of the aqueous and solid phases of a uranium ore carbonate leach slurry were also measured as the slurry was progressively diluted. There was an increase in the uranium content of the solids as the pH of the suspension was lowered, as was observed with the Wyoming bentonite. The results indicate the conditions that should be met with respect to pH control in order to prevent the problem of excessive uranium adsorption in the counter-current decantation washing circuit of a conventional leaching process, as well as in the leaching and restoration phases of carbonate solution mining.

Jan 1, 1983

By Richard A. Bideaux

During 1977 and 1978, a comprehensive study was made of the drill-hole data obtained by Urangesellschaft, USA, from their Juniper Ridge, WY, uranium deposits. This included uranium grade data acquisition, application of a variety of mineral deposit modeling techniques, and estimates of minable reserves, which pointed towards a possible production decision.

Jan 1, 1979

By Peter Werner

Technological advances in mine equipment and milling processes have enabled mining companies to exploit ever lower grades of ore. The result has been larger disturbances, greater volumes of waste, a complex web of infrastructure, and an overall trend towards mega-projects that can extend over several square kilometers. This explosive growth in a mining operation’s disturbance footprint provokes an obvious question: What’s it going to cost to reclaim all of this? At face value, this can be an enormous financial liability for a company, but since the timing of reclamation may be years in the future for many operations, these costs can be heavily discounted thereby limiting the burden on the corporate balance sheet. Nonetheless, mining companies are eager to remove these liabilities as quickly as possible, conversely, regulators want assurance reclamation will, in fact, occur. How might one bridge these competing interests? Navigating the practical and financial requirements of a post-closure landscape requires foresight, judgement and assumptions, however, companies who do not adequately plan for these future expenditures when there is no off-setting income stream will likely face some difficult decisions. Simple risk analysis tools and utilizing the time value of money can help bring some clarity to this end-of-mine life phase.

Feb 1, 2025

By R. G. Reddy

Solid state reduction of roast movat chromite ore with carbon was carried out as a function of C/FeO ratio and temperature in the range 800°C to 900°C by thermogravimetry analysis (TGA). A two stage mechanism, (1) the reduction of FeO present in Roast Movat with carbon monoxide; and (2) the regeneration of CO by the oxidation of carbon with CO2 was proposed. The rate controlling step is the carbon oxidation reaction. A kinetic equation, that of random nucleation, was proposed. The activation energy for the reduction was determined to be 55800 J/mole and is compared to those activation energies determined for other chromite ores.

Jan 1, 1998

By C. RAMADINI, F. NURJAMAN, A. SHOFI, B. SUHARNO

Nickel demand is increasing along with the rising need for stainless steel and other alloy steel/iron. The small addition of nickel in such materials can improve impact strength, ductility and corrosion resistance. Nickel is generally obtained from nickel sulfide ores (nickel associated with sulfur) and nickel laterite ores (nickel associated with iron and magnesium silicate). Almost 60 percent of nickel is now produced from sulfide ores, despite its existence in sulfide ores being less than in laterite ores. However, the depletion of sulfide ore reserves makes the mastery of nickel laterite ore processing of important and immediate concern. Selective reduction followed by magnetic separation has been in development in lateritic nickel ore processing to overcome the issues of high energy consumption and pollution associated with conventional pyrometallurgy methods such as blast furnace and rotary kiln electric arc furnace (RKEF).