Search Documents

By A. A. Berk

In the course of a study of the formation of external deposits on tubes in water-tube boilers it became desirable to determine the sulfur dioxide (SO2) and sulfur trioxide (SO3) in the Due gases. Determinations made by the A.S.M.E. method for SO2 and SO3 in gaseous products of combustion did not give accurate results. It was found that minute quantities of copper, present in the flue gases from the coal in use, caused oxidation of sulfite in the absorption bottle and that the carbon dioxide (CO2) in the flue gases caused high values for SO2. The A.S.M.E. test procedure was revised to prevent oxidation of sulfite in the absorption bottle and to allow for the effect of CO2; subsequent analyses of flue gases produced reliable results. The revised procedure is described.

Jan 1, 1950

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines to evaluate the effectiveness of 10 additives to inhibit the self-heating of coal. Aqueous additive solutions were applied to a bituminous coal with a high spontaneous combustion potential, and the minimum self-heating temperatures (SHT's) of the dried coal-additive mixtures were determined in the Bureau's adiabatic heating oven. The relative effectiveness of the additives was determined by the observed changes in the minimum SHT's of the mixtures, or by the time required for the sample temperature to reach 150" C, compared with the untreated coal and a coal-water blank. Sodium nitrate, sodium chloride, and calcium carbonate were found to be the most effective inhibitors, followed by ammonium dihydrogen phosphate, calcium chloride, ammonium chloride, sodium acetate, and potassium chloride. Two additives, sodium formate and sodium phosphate, promoted the self-heating process. Differential scanning calorimetry experiments on the coal-additive mixtures showed that reactions occurred between the coal and some of the additives, but these reactions did not influence the self-heating process.

Jan 1, 1988

By Dean H. Ambrose

This Bureau of Mines publication summarizes the status of mine electrical equipment reliability research. Failure rate data were estimated from theoretical, laboratory, and field studies. Tables are presented listing reliability characteristics of molded-case circuit breakers, undervoltage relays, ground check monitors, cables, motors, and control circuitry. Application of failure rate data is shown in tables listing maintenance scheduling intervals of components and components that are most sensitive to the probability of hazardous voltages on power distribution systems in the mines. Complete, accurate, and appropriate failure rates on mine equipment are of the utmost importance for reliability evaluations.

Jan 1, 1985

By J. B. Littlefield

This study is one of a number conducted to determine the concentration of dust in the air during the complete cycle of operation in wet drilling information as to various factors connected with drilling in mining operations is considered to be of definite value in the control and prevention of air dustiness, and it is particularly desirable to ascertain What features of present-day wet-drilling operations in mine work contribute to dust disease and to remedy deficiencies when they are found. ACKNOWLEDGMENTS A testing alit through rock strata is being developed by the Mining Division of the United States bureau of Mines at Mount Weather, Va., and the tests discussed in this report were conducted there. This experimental alit in rock, constitutes a typo of laboratory where mine conditions can be closely simulated and where many of the variables likely to occur in an actual mine can be eliminated or at least controlled with reasonable effort, thus affording maximum opportunities to secure fundamental data uncomplicated by extraneous conditions. The authors wish to acknowledge the valuable assistance and cooperation of several members of the Mining Division, particularly C. F. Jackson, chief engineer, McHenry Mosier, associate mining engineer, and G. E. McElroy, supervising engineer, mine ventilation.

Jan 1, 1938

By J. F. Barkley

During the present war emergency, under the urge of the Federal Government to store coal, the following questions are frequently asked by coal users: (a) Will the coal lose any, of its heating value in storage? (b) Will it slack and give a smaller-size coal? (c) Will its burning characteristics change in any way? (d) Will it catch fire from spontaneous combustion? (e) What precautions should be taken when coal is stored? DISCUSSION (a) Loss of Heating Value Studies by the Bureau of Mines show that the loss of heating value of coal in storage commonly has been overestimated. Various types of storage tests were made on New River, Pocahontas, Pittsburgh gas, and Sheridan (Wyo.) coals. The following is quoted from Bureau of Mines Bulletin 136, Deterioration in the Heating Value of Coal During Storage, by H. C. Porter and F. K. Ovitz (p. 8):

Jan 1, 1943

By Greenwald, H. P

The Bureau of Mines has been conducting experiments on the explosibility of coal-dust in the experimental mine for more than 17 years. The results have been published from time to time3, and a forthcoming technical paper4 will summarize the results and discuss them in some detail. The present paper will be limited to a statement of the more important facts that these researches have discovered.

Apr 1, 1929

By K. D. Luxbacher

Understanding methane emissions in underground coal mines is critical for a safe and productive mine. In addition to reasonable estimation of initial coalbed reservoir parameters, it is also crucial that changes in effective stress due to mining and pore pressure reduction are taken into account due to their effects on porosity and permeability. Primary parameters for estimation of emissions or modeling of the mining environment for this purpose are porosity and permeability which can change dramatically as a result of stress redistribution associated with mining and gas desorption from a large coal volume. These parameters affect the emission rates and ventilation requirements, as well as water inflow into the working environment. Stopping leakage, on the other hand, is a secondary stress dependent factor in estimation of emissions, as convergence of the roof and floor strata, compromising the integrity of the stopping, may result in leakage, making prediction of ventilation requirements difficult. This paper aims to examine the effects of porosity and permeability changes of the coal seam on methane emissions in an underground continuous miner section. The models were developed and executed in a dynamic fashion to simulate an advancing section. Through this process, the changes of effective stress in coal, particularly their change paths, on porosity and permeability were incorporated into the models and methane emissions, concentrations, air requirements, water inflow and possible leakage from the stoppings were investigated using a conventional coalbed methane reservoir model.

Jan 1, 2009

By J. B. Littlefield

This study is one of at number conducted to determine the concentration of dust in the air during the complete cycle of operation in wet drilling; information as to various factors connected with, drilling in mining operations is considered to be of definite value in the control and prevention of air dustiness, and it in particularly desirable to ascertain whet features of present-day wet-drilling operations in mine work contribute to dust disease and to remedy deficiencies when they are found.

Jan 1, 1938

By Nicholas Kyriazi

It is of interest to know how to obtain as high an absorption efficiency as possible from a CO2-absorption canister used in closed-circuit breathing apparatus. In this study the Bureau of Mines found that varying the bed depth and the cross-sectional area of a canister changes its absorption characteristics. In tests using four ,1 rectangular, variable-depth canisters with different cross-sectional areas, the Bureau found that, given a constant weight of the chemical absorbent, LiOH, and a constant COa input, the canisters with a greater cross-sectional area reached C02 levels of 0.5 volume-percent in the effluent gas sooner than did the canisters with a greater bed depth. However, resistance to flow through the canister increases with bed depth, and a trade-off is inevitable. It was anticipated that the efficiency of a canister would increase with increasing intergranular air space approaching the tidal volume of the breathing waveform and then level off at some point under 100 percent. This postulation was partially substantiated. Cylindrical and radial canisters were also tested and compared. It appears that shape is not as important a factor in absorption efficiency as bed depth, since neither canister differed significantly from the rectangular canisters with regard to absorption efficiency values.

Jan 1, 1980

By W. C. Phalen

"The Phosphate Rock Market:Indications, in the fertilizer market, point to a prosperous condition, caused chiefly by the growing demand for all classes of fertilizer material in spite of a shortage of supplies. Both of these conditions have been caused by the war. The shortage in phosphate rock is being relieved as production increases, but the supply has not caught up with the demand for this spring's trade, at least. Reports from Florida are to the effect that more than half the necessary quota of laborers are at work. This may not appear to be a very good showing, but even this situation is en¬couraging because there is a larger force now at work than has been the case for some time, and it is steadily, though slowly, increasing. Some of the producing companies are conducting advertising campaigns to get laborers back to the phosphate fields and attractions in the way of better housing and living conditions are being offered.Producers are far more confident about the situation than they were two months ago, and though the shortage will not be met before the end of 1920, theme is a surplus accumulating over what is going out on existing contracts.Quotations are now being offered on all Florida rock excepting land pebble and this, it is expected, will be soon quoted.Quotations on Florida rock per ton are as follows:"

Jan 1, 1920

By George S. Koch

In preparing diamond-drill core samples for assay at the Homestake mine, Lead, S. Dak., 5-foot intervals of core are processed through three stages, crushing, grinding, and pulverizing, and portions of the core material are discarded after splitting at each stage of preparation. Then two 1-assay-ton fractions are taken from the pulverized material and assayed. This report investigates alternative methods of sample preparation. The consequences of crushing, grinding, and pulverizing all rather than part of the core are appraised through the statistical analysis of assay results from 118 5-foot intervals of core. Evidently, a substantial improvement in precision at small additional expense is obtained by grinding most or all of the core before splitting. Pulverizing all of the core would be desirable only if doing-so would cost less than assaying five random splits from each interval. Graphs and tables detail appropriate procedures to obtain specified precisions. The experimental design and methods can be applied to similar problems in preparing core and other geological samples.

Jan 1, 1972

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Guatemala has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State.

Oct 1, 1929

By A. H. Warner

Sphalerite crystals occur sparingly in minor faults and pockets in a coarsely crystalline dolomite on the Brown-Tipton farm near Greenville in Greene County, Tenn. After several visits by U. S. Bureau of Mines engineers and U.S. Geological Survey geologists, a survey was r: the in the fall of 1944. Upon their recommendations, trenches on the Brown farm under Bureau of Mines supervision. In each case, the bed most favorable for zinc deposition was exposed. In the finished trench bottoms no zinc minerals are visible.

Jan 1, 1950

By J. I. Paige

The Bureau of Mines, U.S. Department of the Interior, conducts research on methods to minimize the requirements for mineral raw materials through conservation, substitution, and increased minerals and metals recovery from primary and secondary domestic resources. To further this goal, prior Bureau research had devised a pyrometallurgical technique (RI 8211) to recover metallic iron and copper from molten copper smelting furnace slags by carbothermic reduction. As a continuation of this Bureau research on the carbon injection technique, reverberatory and electric furnace slags were treated in an 800-kva electric arc furnace by simultaneously top feeding the slag and injecting coke breeze into the bottom of the molten bath. Results of the tests show that 76 to 89 pct of the copper and up to 48 pct of the iron contained in the smelting furnace slag were recovered in a metallic phase, while 56 to 82 pct of the carbon injected into the sys-tem was utilized as the reductant. Laboratory evaluation has shown that the metal product, which contains 86.9 to 95.0 wt-pct iron and 1.3 to 4.1 wt-pct copper, will be a satisfactory medium for recovering copper by cementation. The expected energy consumption for the process is 110 kwhr per ton of molten slag treated and 520 kwhr per ton of solid material charged.

Jan 1, 1982

By David C. Oyler, Paul W. Jeran, William P. Diamond

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbecl at a vertical depth of 999 feet, The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a “bird foot” pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

By John J. McClelland, Gerald T. Homce, John R. Thalimer

The U.S. Bureau of Mines has investigated the early detection of insulation failure in squirrel cage induction motors for the past 4 years. Research was done using a sophisticated empirical data-modeling technique based on values calculated from a motor's voltage and current phasors. This technique produces two polynomial equations that calculate the insulation leakage current and power. These models were implemented in a prototype system that monitors six motors on a continuous miner for insulation leakage. These insulation leakage values are used to anticipate insulation failure. The system consists of a motor-data-system for each motor on the machine and a control computer located away from the miner. Each motor-data-system consists of an analog interface to the motor's voltages and currents, a single-board computer that reads digitized data and calculates voltage and current phasors, and a bus node that interfaces the single-board computer with the rest of the system by way of a serial bus system. Using this bus system, the control computer requests and receives phasor data from the motor-data-systems. From these data the control computer calculates and displays two deterioration values for each motor, for leakage current and power, using Bureau-developed models. These values are stored in a data base from which the user can display graphs of each motor's deterioration values over time.

Jan 1, 1992

By Frank E. Chase, John Rusnak, David Newman

During the past quarter century, coal mine geologists have evolved from providing a qualitative description of drill core and coal reserves into quantitative geotechnical specialists who bridge the gap between geology and engineering. In the late 1970’s and early 1980’s, hazard prediction mapping was in its infancy. At best, hazard maps identified rudimentary structures and conditions such as stream valley locations, sandstone/shale transition zones, and lineaments. A “technical disconnect” had existed between geologists and mining engineers as each profession operated largely independent of each other. Engineers did not readily integrate geology and geologic conditions, with the exception of coal thickness, into mine planning. Geologists were relied upon for reserve estimates and did not participate in mine planning or design. The employment and market slump of the 1980’s and 1990’s combined with mining more challenging reserves mandated that this gap be bridged and forced geologists to learn to speak more “numerically” to engineers so they could be understood. The purpose of this paper is to describe the procedures and thought processes used by coal mine geologists when determining various mineability and reserve extraction feasibility issues. The paper will also address underground geologic hazard mapping and prediction techniques. To achieve these objectives, the opinions and experiences of leading coal mine geologists, geotechnical and strata control specialists across the United States were solicited.

By M. J. Ankeny, J. J. Forbes

The United States Bureau of Mines often receives inquiries from the mineral , petroleum , and allied industries concerning the essential steps to be taken in the formation of Holmes Safety chapters and councils . The purpose of this circular is to answer in a general way such inquiries and to relate briefly the history and work of the Holmes Safety Association to the present date .

Jul 1, 1931

By Oliver Bowles, J. E. Crawshow

A line of cordeau detonating fuse was placed in hole No. 2, no electric detonators being used in the hole. After 12 or 13 cases of 40 per cent nitro starch powder had been poured into the hole in loose form, it was found that a space of only 17 ft. remained for stemming. It was decided that space for an additional case of powder might be obtained by tamping the charge. The tamping was done with a heavy plunger, about 3 or 3 inches in diameter and 10 inches long, made of lead with an iron core with an iron eye in the top to which a 3/4 inch rope was attached, and weighing between 30 and 40 pounds. This weight was intended for use in sinking explosive in wet holes, and not for tamping. It is estimated that the tamping had continued at least 10 The quarry superintendent had gone a considerable distance for a box of powder, returned, and reached a point about 10 feet from the hole, minutes.

May 1, 1920

By Jos. R. Guiteras

This paper is one of o. series describing mining and milling methods and costs being published by the United States Bureau of Mines. It presents the results of a study of the Alice mine by the writer in December 1936. ACKNOWLEDGMENTS Acknowledgment is made to J. Fred Johnson, mining engineer off the American Smelting & Refining Co., for permission to visit the property; and to Arthur F. Johnson, general superintendent at the property, for his friendly cooperation in contributing the information contained in the paper.

Jan 1, 1939