Search Documents

By Chuan-liu Wang

The bionic non-smooth surface has the characteristics of anti-wear, and reducing resistance. Based on bionic non-smooth surface?s characteristics, a bionic drill bit was developed. When the bionic drill bit is used, a bionic non-smooth surface forms on the crown of bionic drill bit. This surface can be used to extend the life of drill bit and improve drill efficiency. The bionic unit diameter and arrangement were researched in this paper to determine the optimal bionic non-smooth surface for further improving the life and efficiency of drill bit. Four bionic samples having the same structure size, materials and arrangement were designed and manufactured. After being sintered, the abrasion ratios of the four bionic samples were tested, and the results show that the abrasion ratio of Nos. 3 and 2 were similar (only 2% difference) and higher than that of No. 1 and 4. Therefore, the optimal diameter of bionic unit is 1.5 and 2.0 mm. Small diameter bionic drill bits were designed and manufactured, and tested in the laboratory. The results show that not all bionic structure bodies are better than normal diamond bits, except the bionic unit arranged in a reasonable range. When the angle was 24° and 30°, the arrangement of bionic unit were more reasonable, which shows the superiority of the bionic coupling bit.

Aug 1, 2013

By H. T. Michels

Recent laboratory studies show that several bacteria, known to be human pathogens, die when they come in contact with copper and copper alloy surfaces. The amount of live bacteria drops by several orders of magnitude, to zero, on copper alloys in a few hours. In contrast, no reduction is seen in the concentration of live organisms on stainless steel during the six-hour test period. Aluminum painted and coated surfaces and plastics would show behavior similar to stainless steel and show no effect. Coatings and other surfaces claiming to be antimicrobial showed little to no effect. These results suggest the selection of copper alloys for surfaces exposed to human touch can materially assist in reducing the transmission of infectious organisms. In order to make antimicrobial claims in the United States, the approval of the US Environmental Protection Agency (EPA) is required. The EPA-required efficacy testing is described and the test results are summarized. It is anticipated, that once regulatory approval is obtained, that this will facilitate the introduction of antimicrobial copper alloys in hospitals, nursing homes and other healthcare facilities, as well as schools, and public buildings. Some of the application and barriers, to entry into the healthcare markets are mentioned.

Jan 1, 2007

By J. Pontt

Gearless mill drives (GMD) offer high performance for torque and speed control for grinding mills and have been applied successfully in modern concentrators for wet grinding with mill diameters from 34 to 40-feet. It is considered a mature technology. However, recently, some large GMD?s have presented unexpected failures in stator and rotor subsystems. The phenomena involved in such failures has shown a complex nature and surprised users and manufacturers. The manifestation of such failures has been observed as mechanical damages to certain components of ring motors. This paper presents a discussion on the electromagnetic forces that can generate stresses in the electrical ring motor that can produce failures and outages. Guidelines for further research and contributions to improved reliability of GMD?s are proposed.

Jan 1, 2012

By T. Sakai

Present authors have succeeded in single pass large draught rolling of AZ31 and ZK60A magnesium alloy sheets below 200 °C without heating rolls by raising rolling speed above 1000 m/min. Heavy reduction larger than 60% can be applied by single pass high speed rolling even at room temperature. The rolled sheets showed fine recrystallized microstructure by dynamic recrystallization. The improvement of workability at lower rolling temperature is due to temperature rise by plastic working. In high speed rolling, almost all of the work done by plastic deformation is converted into the heat that raises the temperature of the sheet during rolling because the heat did not flow out of the sheet by conduction and radiation within very short time.

Jan 1, 2006

By A. Ignatieff

"THE WORLD'S coal resources represent the largest component of non-renewable energy resources. Coal is now regaining Its position following a temporary decline, particularly in North America during a period of about a quarter of a century. This period provided the opportunity to improve both surface and underground mechanization, thereby increasing the productivity and improving conditions for humans in the mines. Similarly, in preparation, improved cleaning of coal from various impurities including sulphur was achieved, to meet the more demanding requirements for coking coal. Progress was also made in combustion, particularly related to the reduction of pollution. Canada participated in most of these developments, despite the country's strong commitment of the use of hydrocarbons during this period. _Bearing in mind the vastness of this land (3.85 million sq. miles) by comparison with countries like U.S.A., U.S.S.R., and China, Canada's coal resources estimated to date are not large and they are scattered. The original evaluation of 1913 estimated the ""reserves"" from seams over one foot in thickness and a limiting depth of 4,000 ft at 1.2 trillion metric tons. D:. ~.R. MacKay, in his evaluation for the 1946 Royal Commission on the coal industry, known as the Carroll Commission, reduced the ""reserves"" to 99 billion short tons. The increased knowledge now available would indicate that the 1913 estimated was too liberal and the 1946 estimate too conservative but both were closer to a resource than to a reserve designation. Some adjustments of Dr. MacKay's estimates were made in 1970 by B.A. Latour of the Geological Survey of Canada and L.P. Chrismas of Energy, Mines and Resources Canada (EMR). In the last decade the Alberta Energy Resources Conservation Board has developed its own methods of evaluating coal resources and reserves. A methodical approach of exploration and evaluation was carried out by Saskatchewan jointly with the federal government of the lignite resources of Southern Saskatchewan. A similar joint program is in progress in Nova Scotia. Meanwhile, the industry itself carried on an extensive exploration program on the outcrops of promising projects in the Inner Foothills belt of Alberta and British Columbia in preparation for surface mining on a very large scale, with some development of hydraulic mines. All these activities have been reflected in the increase of the country's resources and reserves, which now fortunately are separately defined. In 1979 EMR issued Report E.R. 79/9(1>; the data were developed in 1978 and provided to the World Energy Conference Organization<2>. In 1980 the World Coal Study (Wocol), an international group that included Canada carried out a study which updated the W.E.C. data, indicating some reduction of the 1978 figures; quantities were reported in million metric tons of coal equivalent (C.E.)*(Jl."

Jan 1, 1985

By E. M. Stiles

Introduction The papers that follow deal with recently completed major improvements in practices at the Sullivan operations in Kimberley. The papers have been prepared by members of the Consolidated Engineering Staff and outline the construction programme which has been in progress for the past three years, entailing an expenditure of some millions of dollars. Four major operational changes have been brought about in the mine and concentrator. They are: (1) A change in backfill procedure for filling stopes below the 3900 level. (2) A 12,000-ton,per-day sink-float plant at the concentrator. (3) A new haulage system from the mine to the concentrator. (4) A completely new crushing plant and ore storage facilities located underground. A brief outline of the background and history leading up to this overall project will be given to show how each started as an independent betterment and how they were finally co-ordinated into one major programme. The first of these, namely, the necessity for backfilling stopes below the 3900 level, was the most pressing problem. All filling to date bad been done above the 3900 level, where mining was carried on in an irregular pattern of open stoping. Stopes below the 3900 level were first opened in 1940 and are being worked on a regular pattern of panel sub-level open diamond drill stopes. The two areas are separated by a sill pillar traversing the entire length of the vein at the 3900 level elevation.

Jan 1, 1950

By Farzaneh Abedini, Narain Hariharan, Lucas C. McFarlane, Nikolas A. Romaniuk, Tiffany Thayne

The use of dewatered mine tailings as backfill material (commonly referred to as ‘paste’ backfill), is the most practiced form of backfill in Canada providing significant environmental benefits by reducing the size of external tailings facilities and improved economics through enhanced resource recovery. Paste backfill operations reuse filtered mine tailings with a cementitious binder and water to create a slurry that is hydraulically transported to refill underground stopes, later forming a structural network of cemented tailings in the mine stopes. Unlike typical structural applications that utilize General Use (GU) Portland cement; modern paste backfill operations maximize strength performance by blending Portland cement with ground granulated blast furnace slag (GGBFS) or other supplementary cementitious materials (SCMs). GGBFS and other SCMs offer key performance benefits and carbon reductions; however, the availability of these SCMs is rapidly dwindling in today’s carbon-constrained economy. This paper examines the development of an alternative binder system that provides similar performance and carbon reduction to that of GGBFS for mine backfill operations. The binder utilizes the chemical reaction between a reactive source of aluminosilicates and available calcium from calcium oxide or calcium hydroxide to replace between 50 to 100% of GGBFS. The performance of the binder is examined with insights into the hydration mechanisms that generate mechanical strength in the cemented paste network. Paste backfill slurries require precise engineering to create a material that maintains flowability during pipeline transport and generates enough strength to meet operational targets once placed in the stopes. Engineering of such slurries requires large amounts of water to be added to the binder-tailings matrix, far exceeding the typical water to binder ratios used in concrete mix designs. This characteristic of paste backfill warrants great emphasis on understanding the hydration mechanisms of the binder used in the paste backfill system. GU cement is typically composed of 50-70% tricalcium silicate and 15-30% dicalcium silicate.  The hydration mechanisms of these compounds consume 4 to 6 units of water to mineralize into calcium silicate hydrate cemented phases that result in compressive strength development. Cementitious aluminate and aluminosilicate phases make up 5-20% of GU cement and aid in secondary performance characteristics such as set time. Certain calcium aluminate hydrate phases such as monocarboaluminate and ettringite mineralize 10 to 32 units of water into their crystalline structure. Hydration products such as ettringite are traditionally avoided in construction applications due to their propensity for volumetric expansion after cement setting, leading to micro-fissures and subsequent strength degradation (known as ‘sulfate attack’). This paper proposes that such hydration products benefit the strength development in paste backfill slurries with the aforementioned characteristics due to their greater potential to mineralize free water. The newly developed calcium aluminosilicate binder is designed to replace 50-100% GGBFS or other SCMs used in paste backfill systems and meet operational strength requirements by providing exceptional hydration characteristics through cementitious reactions. Additionally, the aluminosilicates used have a minimal carbon footprint and a secure supply outlook, thereby allowing mine operators access to a low-carbon binder option throughout the mine’s lifespan.

May 4, 2025

By M. Sukhram

In the year 1992, T.A. Utigard published a paper titled "The measurement of the heat-transfer coefficient between high temperature liquids and solid surfaces." In that work, he instrumented an agglomerate of materials with thermocouples to infer the heat transfer coefficient of a high temperature liquid on a solid. The purpose of that research was to help in the design and operation of metallurgical reactors. Since that time there have been many researchers that have worked to characterize heat, mass, and momentum transfer phenomena in high temperature metallurgical processing operations. This paper presents results from the author’s experience with instrumenting thermocouples in copper elements coated with carbon to infer velocity of high temperature liquid metals. It also presents a methodology to determine velocity of a high temperature liquid by inferring the local heat transfer coefficient at a solid-liquid interface

Jan 1, 2015

"RésuméDans la première partie de cet article on discute Ie mode d&apos;écail age aetueJJement en usage dans des mines souterraines. Par la suite, on presente la problematique d&apos;écaillage à l’aide de barres conventionnelles et on discute les plus recénts développements des outils d&apos;ecaillage portatifs et mécanisés ainsi que les techniques de détection des roches branlantes. Plus tard, on analyse la tâche d&apos;écaillage avec des barres conventionnelles. Dans les chapitres qui suivent on présente un concept d&apos;un outil d&apos;écaillage portatif et mécanisé développe à l&apos;Université Laval, ainsi que les résultats des essais de cet outil, effectués dans quelques mines au Québec. On constate que Ie nouvel outil d&apos;écaillage démontre un potentieJ intéressant tant au niveau de l&apos;effort requis pour effectuer la tâche d&apos;écaillage que de la sécurité des mineurs.On conclut que l’application de cet outil fera un pas important sur Ia voie d&apos;amélioration des conditions de travail dans les exploitations souterraines, tout en assuarnt une qualité accrue de l&apos;écaillage.AbstractThe first part of this paper discusses the type of scaling operations presently in use in underground mines and derma; a scaling factor which is expressed as the:: area necessary to scale to extract one ton of ore. Subsequently, the problems associated with conventional scaling methods are discussed as well as recent developments in mechanized hand-held scaling devices and methods of loose detection. The elements of the scaling process are further analyzed. In subsequent sections of this paper, the conception and design of a mechanized scaling device, developed at Universite Laval is described. The results of field tests conducted in Quebec hard rock mines are presented. The experimental findings show that the mechanized hand-held scaling device shows great potential in improving the productivity and safety of underground mining operations."

Jan 1, 1995

By Robert B. Parsons

"The Whitehorse Mining Initiative (WMI) brought together all of the key stakeholders in Canada&apos;s mining industry to develop a framework whereby the industry can meet the challenges that it faces into the 21st century. The WMI Accord7 which was signed at the annual Mines Ministers Conference in Victoria, British Columbia, on September 137 1994, touches all of the important issues that confront the industry, including taxation. IntroductionSeptember 13, 1994, was a historical day for Canada&apos;s mining industry. On that day, on the occasion of the annual Mines Ministers Conference in Victoria, British Columbia, the Whitehorse Mining Initiative (WMI) Accord was signed by the leaders of the five principal stakeholders in the industry: industry; government; labour; environmentalists; and aboriginals. The Accord is the culmination of two years of hard work and intense collaboration by these stakeholders. But, the Accord is not the end result. The Accord can better be described as a springboard to a prosperous future for mining in Canada.The WMI had its beginnings at the Mines Ministers Conference in Whitehorse, Yukon, in September 1992 (hence, the name of the initiative). At that time, the mining industry was well aware of the serious challenges facing the industry, including significantly increased competition for mineral investment from other mining countries, coupled with an atmosphere of uncertainty surrounding land access, environmental regulations, and taxation. The diversion of investment abroad was hurting, and would continue to hurt, all Canadians. Something had to be done. At the 1992"

Jan 1, 1994

By I. Filippova, L. Filippov

"The by-product potential of light rare-earth elements (LREE, La, Ce, Nd) and rare-metals (W, Nb, Sn) within the St Austell kaolin deposits (UK) is related to the kaolinisation process, which liberates the accessory heavy minerals of the host granite in the clay matrix and allows their separation in the waste streams. As a consequence these minerals are pre-concentrated in the micaceous residue which displays relatively high LREE content (around 170 ppm) hosted by monazite which is mainly distributed (up to 95%) in the -100 µm fraction. A combined gravity/flotation concentration flowsheet, starting with classification of the residue into 3 size fractions (+150 µm, 150-53 µm and -53µm) was developed. This study presents the results of the clay-rich -53 µm size fraction beneficiation by flotation using sodium oleate and hydroxamate as collectors.The effect of dispersant addition during de-sliming operations on flotation efficiency was also investigated. The LREE grade in the floated product obtained with sodium oleate increased from 3370 ppm to 5350 ppm and recovery from 30% to 80% with dispersant which is attributed to clay coating. Comparison of flotation performance and Falcon Ultra-Fine (UF) concentration of monazite to previous results obtained with Falcon Semi-Batch (SB) gravity concentrator on the unscreened raw residue clearly shows that flotation of the fine residue is more efficient than Falcon UF and Falcon SB. Indeed Falcon UF produced high recoveries (87-95%) but with almost no enrichment (1.3-1.4 ratios) whereas Falcon SB concentration of unscreened residue produced higher grades (up to 0.6 % LREE) but with low recoveries (17-22 %). These preliminary results show that LREE can be pre-concentrated suggesting that the micaceous residue stream (and the associated tailings dams) could be considered as a potential resource for these metals."

Jan 1, 2016

By S. Radacina Rusu

The satellite-based global positioning system (GPS) has significantly changed the way site operations are carried out in surface mining. The GPS has impacted safety, productivity, fleet efficiency, and maintenance practices. However, no comparable global localization system exists for underground mines. This paper discusses recent work in the application of ideas from the mobile robotics research community to the problem of real-time vehicle positioning in underground drift networks. Related previous work recently focused on the creation of globally consistent 2D maps of underground environments that possess sufficient detail to be used for underground localization. Our current work entails the development of a GPS-like system for mobile mining equipment, with results given from both laboratory and field experiments.

May 1, 2011

By C. R. Edwards, D. R. G. Watt

"Equity Silver Mines Ltd. a member of the Placer Development group of companies operates Canada's largest silver mine near Houston in north-central British Columbia. Initially, the silver-gold-copper flotation concentrate contained excessive levels of antimony and arsenic, so a leach process was installed to remove undesirable metals and provide improved smelter terms for the leached concentrate. The leach plant which has been fully described elsewhere (1, 2, 3), was forced by deteriorating process economics to shut down in April 1984. Equipment was mothballed and alternate uses sought.The Endako Mines Division of Placer Development Limited, located some 150 kilometres east of the Equity mine site, shut down its molybdenite mining and milling facilities in the spring of 1982. Endako has continued to produce molybdic oxide (molybdenum trioxide or MTO) via intermittent roaster runs, and also a high purity, lubricant grade molybdenum disulfide in the Ultrapure Plant. With the steel industry in the doldrums, molybdenum chemicals present an alternate and growing potential for molybdenum sales. In 1982 Placer Development began testing this market. Molybdenum chemicals were produced in the United States on a toll basis using Endako MTO as process feed. The transfer of this production to Canada was being considered when Equity's leach plant shut down, and it was noted that most of the equipment and skills necessary could be provided by the leach plant. See Figure 1.A careful investigation of process requirements was completed by engineering and production staff at Equity and Endako. A provisional capital and operating cost estimate was made, and it was decided to perform a test run during July 1984. There were strong reasons to proceed with this project. A positive cash flow was expected for both Endako and Equity. Endako would have product to continue to expand in the molybdenum chemicals market with the added selling point that now the complete production process would be under direct control of Placer Development companies. Equity would further benefit since a portion of the leach plant would continue in operation thus maintaining and exercising our hydrometallurgical engineering and operating skills. Finally, Equity would have a base from which to search out other processes adaptable to the idled leach plant equipment."

Jan 1, 1986

By H. A. Baxter

THE Eustis concentrator is located about nine miles southwest of Sherbrooke, on the main line of the Quebec Central railway. The concentrator is served by a side track parallel to the main line, and all supplies for both the mine and mill are delivered at the mill yards. The concentrator treats 250 tons of copper-iron ore daily by preferential flotation, whereby, first, the copper sulphides are floated and the iron pyrite is depressed, and, second, the iron pyrite is reactivated and floated, resulting in an iron pyrite concentrate and tailing, the latter going to waste. During 1934, 71,709 tons of ore were treated, averaging 3.712 per cent copper and 32.1 percent iron, with a small amount of silver and a trace of gold. The recovery was 93.77 percent of the copper, and 70.43 percent of the iron as iron concentrate. The copper concentrate produced averaged 25.623 percent copper and the iron-pyrite concentrate averaged 42.13 percent iron and 49.173 percent sulphur. HISTORY The first mill at the Eustis mine was built in 1904 (1). For a few years previous to this rime, some jigs had been operated to concentrate the fines from the mine, the coarse ore being hand-sorted. Both the fines and sorted lump ore were shipped to acid plants. The building of the mill was based on test work carried out by Professor Robert H. Richards at the Massachusetts Institute of Technology. The method of concentration consisted in careful classification in a Richards classifier, which made six different sized products. These products went to Wilfley tables, where a concentrate, middling, and tailing were made. The middling was returned to the rolls. Crushing was done by a jaw crusher and two sets of rolls, resulting in a screen size of about five-mesh.

Jan 1, 1936

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations for the smelting and refining of non-ferrous metals, and it is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate. It is also the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y zinc. Since then, production capacity has increased, and at present, it stands at 240,000 t/y zinc. In this paper, the leaching process and particularly the operation of the jarosite circuit is reviewed, specifying process improvements to treat high iron calcines.INTRODUCTIONTwenty years ago the Electrolytic Zinc Plant in Peñoles was treating high quality zinc concentrates with low concentrations of iron (~7.5 wt.%) and silica (1.8 wt.%). Nowadays the quality of zinc concentrates is poor with a typical iron content of around 11 wt.% and silica at 2.0 wt.%. This has created numerous processing problems in our roast-leach-purification- electrolysis sections. In order to meet customer requirements it is necessary to find processing solutions to assure the operational continuity of the plant. These processing solutions are the focal point of this paper.REVIEW OF THE LEACHING PROCESSThe purpose of the leaching process is to recover the metals, mainly zinc, through a series of extraction stages with sulphuric acid solutions, which progressively increases the zinc dissolution. After the series of acidification stages, the solution, which is rich in iron, is sent to the jarosite circuit to separate zinc from iron (Garcia & Valdez, 1996). The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper. Then this solution is sent to the tank house to feed the electrolytic cells."

Jan 1, 2016

By C Jincheng, L. Liang, L. Wenjun

"Considering overgrinding in a grinding process, the grinding characteristics of comminuted hematite products using a HPGR and a conventional CC were comparatively studied. The major properties including particle size, grinding kinetics and grinding technical efficiency (Et) were investigated. Individual size distributions (ISDs) of -2.0mm in a HPGR product showed a more significant “double-peak” characteristic than a CC product. As a result, HPGR products were finer and had a wider full-size distribution because of the greater proportion of fines. The parameters m and zi in m-th order grinding kinetics were analyzed by the partial-derivative method and the critical time tc(tc = exp (1/ zi)) was obtained. zi mainly affected the breakage rate when t < tc; otherwise, m mainly affected the breakage rate. In these tests, tc was considerably higher than the grinding times, and HPGR products yielded a higher zi-value than the CC product for the same sieve size. This indicated that HPGR products had a higher breakage rate and needed a shorter grinding time for a certain grinding fineness. Et was calculated by simulating the size distributions of batch grinding products. HPGR products gave a lower Et at a decreasing rate than the CC products for -2.0 mm feed and -0.5mm feed, and then showed a slightly higher Et for -2.0+0.5 mm feed. This indicated that overginding in HPGR full-size products was more serious under the condition of coarse grinding, whereas the efficiency was higher and overgrinding weakened significantly in HPGR coarse products because of screening-out fines. Based on the above research, a new process of “ultra-crushing in HPGR – classified grinding” was advanced, reducing ores tonnage into first stage ball mill significantly, improving grinding efficient and weakening overgrinding in the whole grinding process.INTRODUCTIONIn mineral processing, comminution accounts for a substantial portion (approximately 60~70%) of the energy consumed in plants. As an ultra-fine crushing equipment,the application of the HPGR for industrial comminution has been paid close attention because of its low specific energy, low steel consumption, high capacity and high ratio of reduction, among others (Schonert, 1998; Norgate & Weller, 1994; Fuerstenau & Kapur, 1995). HPGRs comprise two counter-rotating rolls that draw feed material into the roll gap. One roll is fixed to the mainframe, while the other movable roll is mounted on slides and positioned by hydraulic rams. The specific pressing force (SPF) (i.e., total force divided by projected roller area) is typically in the range of 3~9 N/mm2 depending on the application, while pressures of up to 1000 N/mm2 have been measured within the operating gap (Maxton , Morley, & Bearman , 2003)."

Jan 1, 2016

By M. Sanchez

In the last decades, the Chilean copper mining and metallurgical industry have had to modify their technological processes to meet the environmental regulations implemented by the Chilean government, and also to support the pressure of the public opinion. Thus, air quality standards for sulfur dioxide and particulate matter (primary and secondary), plans for reducing emission of arsenic by the Chilean copper smelters, effluents discharge limits, among others regulations were applied by the environmental agency. Additionally, agreements on cleaner production were carried out by mining sector and government. Now, a draft law on mine closure, and another on environmental mining wastes (abandoned mines) are being discussed by the authorities and the mining sector. In the context, production and environmental impacts in different ways to produce copper in the Chilean mining industry are reviewed and regulatory tendencies as well as abatement technologies today used are exposed and discussed in this presentation. Pyro, hydro and electrometallurgical processes employed and their current effluent and contaminants are presented showing various alternatives of treatment in the copper industry. An update of regulations established in Chile vis a vis copper production, with an especial attention to mine closure are also presented.

Jan 1, 2007

By W. E. Cockfield

THE object of this paper is to review recent geological work in the Cariboo district and to present notes on the recent development of mineral properties. The Geological Survey has done considerable work in the Cariboo district, extending over a period of years. In 1885 and 1886, Bowman (1) mapped the geology of a large area. In 1922 and 1923, Johnston and Uglow (2) mapped Barkerville area in some detail and prepared a report on the placer and lode gold deposits. In 1931 and 1932, Cockfield and Walker (3) mapped the Quesnel Forks area. In 1933, Hanson reported on Willow River area ( 4), and in 1934 made a detailed examination of part of the Barkerville area (5). In 1935, Lang commenced work on the Keithley area, lying to the southeast of the Barkerville area, and in 1936 published a preliminary re-port (6). The work on Keithley area was continued in 1936 by both authors of the present paper. As the results of the earlier work have been published, this paper will be concerned largely with Keithley area, that is, the part of the region lyinp between longitudes 121° 00&apos; and 121° 30&apos;, and latitudes 52° 45&apos; and 53° 00 . This area lies astride Cariboo (Swamp) river and extends north some 17 miles from Keithley, which is situated near the southern border of the map-area (see sketch-map). Points in the western part of the map-area are fairly accessible. A road extends from Barkerville to upper Cunningham creek, and from this a trail crosses Snowshoe plateau to Keithley. A second trail from this road leads to the lower falls on Cariboo river. From this road, a branch road leads to upper Antler creek, with a trail leading from this branch road to Keithley. Part of this western half of the area is made up of the Snowshoe plateau, which constitutes a gently rolling surface, at or above timber line, where trails are largely unnecessary.

Jan 1, 1937

By Shuan-cheng Gu

Roof bed separation often occurred due to the deformation incoordination of surrounding rock following the excavation of mine roadway. Bed separation has effect on the bolts, and the estimation of the influence will directly affect the safety of support systems. In this paper, the hyperbolic function model to analyze the load transfer mechanism on the bolts was simplified as the exponential function form for easy calculation. An elastic-plastic analysis model of the bolt loading occurred by the bed separation was established. And the development low that the bed separation affected to the bolt loading was discussed. According to the parameters analysis of different separation values and locations, the influence law of the bolt loading caused by roof bed separation was summarized. Finally, the effects of bed separation were considered for the bolting design, it was able to provide a reference to the anchorage design of stratified rock.

Aug 1, 2013

By K. M. Deen, E. Asselin

Hydrometallurgical processes, i.e., Cu extraction from a mineral concentrate and Zn electrowinning, are coupled in a battery-like system. A naturally-sourced CuFeS2 concentrate mixed with activated carbon is used as a positive slurry electrode separated by a membrane from the negative compartment. The Zn is deposited on the negative Al current collector from the circulating solution containing 100 g L–1 Zn2+ in 0.2 M H2SO4. In this battery-like system, both CuFeS2 oxidation and Zn deposition are possible during the charging cycle. The additional benefit of this setup is the energy storage if discharged by re-dissolving the Zn in the negative compartment. Cyclic charge/discharge testing revealed oxidation of the mineral concentrate supported by the Zn2+/Zn redox reaction. The coulombic and energy efficiencies increased monotonically to 95.6% and 43%, respectively, with approximately 7% Cu extraction during the first 10 charge/discharge cycles (completed in 2.4 hours). The discharge energy density also increased from 2.7 to 36.2 mWh L–1. In the following 90 cycles, the low energy (~14%) and coulombic (~33%) efficiencies that were obtained confirmed the progress of irreversible reactions e.g. Cu extraction from the mineral concentrate. Overall, approximately 16% Cu was extracted from the mineral concentrate over 100 charge/discharge cycles (or about 12.2 hours). INTRODUCTION Chalcopyrite (CuFeS2) is the main economic copper-bearing mineral, which is generally processed through pyro-metallurgical methods to produce Cu. However, environmental challenges with smelting, depletion of high-grade ores and a large number of impurities (some toxic) have resulted in continued research aimed at the development of hydrometallurgical technologies to process CuFeS2. There are a number of different proposed hydrometallurgical routes in the literature to treat CuFeS2 concentrates, but only a few have attained commercial acceptance (Dreisinger, 2006). Zn is another commercially important metal that is mainly produced via acid leaching of roasted sphalerite (ZnS). The pregnant leach solution is rigorously purified to remove all the soluble metal impurities, particularly those that are electrochemically more noble than Zn and present large kinetic activity towards H2 evolution (Hu & Piron, 1992; Mackinnon, Brannen, & Fenn, 1987; Mureşan, Maurin, Oniciu, & Gaga, 1996). Metal impurities such as Cu, Co, Ni, Cd, Pb, Sb, As, Ge and Fe etc., if they exist in the leach liquor beyond the tolerance limits, can decrease the current efficiency during electrowinning and deteriorate the deposit quality (Alfantazi & Dreisinger, 2001). A complete flow sheet, describing the process steps of Zn metal production from mine site to pure metal is presented elsewhere (Brown, Meisenhelder, & Yao, 1983).

Jan 1, 2019