Search Documents

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007

By D. M. Baird

ABSTRACT A revised stratigraphic section of Carboniferous rocks which occupy about 700 square miles in southwestern Newfoundland is presented. Gypsum, which outcrops at thirty-five different localities, is found to belong to four principal zones in the section. The newly mapped structure of the region makes the otherwise random occurrences of gypsum appear as systematic outcroppings of the four zones which follow the regional structure. Details of several occurrences are given and those most advantageous for exploitation are pointed out. INTRODUCTION ROCKS of Carboniferous age occupy an area of about 700 square miles in southwestern Newfoundland. They occur in a belt, from 5 to 15 miles wide, which extends from the head of St. Georges bay southwestward for 65 miles to the mouth of Little Codroy river (see Figure 1). Several hundred feet of Pennsylvanian rocks overlie rocks of Mississippian age, which are at least 12,000 feet thick. The rocks of the Carboniferous section of Newfoundland are very similar to those of Nova Scotia and represent a northeastward continuation of the same palaeophysiographic conditions. Mississippian measures of Windsor equivalence include thick gypsum deposits which outcrop at many places and which extend under large areas as indicated by sink-holes and by structural considerations.

Jan 1, 1951

By A. Saigal

A finite element analysis based investigation using DEFORM software was undertaken to model the extrusion of 15% alumina and 15% silicon carbide reinforced aluminum metal matrix composites. The study dealt with predicting the extrusion load as a function of ram displacement and initial billet temperature. The finite element simulation was also used to determine the maximum extrusion load, temperature distribution, maximum temperature, strain rate, velocity and stress distributions in the billet during the hot extrusion process. The constitutive equation used was of the type: Z = E exp(Q RT) = A{sinh(ao-)}" where Z is the Zener-Hollman parameter (temperature compensated strain rate), s is the strain rate, Q is the activation energy, R is the gas constant, T is the absolute temperature, a is the flow stress and A, a and n are constants. Based on the work of Davies et al and McQueen and Konopleva, the values of Q (KJ/mol), a (MPa-1), n and A for aluminum 6061 composites reinforced with 15% alumina and 15% silicon carbide used are 181, 0.024, 4.15 and 1.33x10'2 and 233, 0.052, 2.60 and 1.26xl0'4, respectively. Even though the individual parameters are quite different, it was found that the predicted maximum extrusion load, temperature distribution, maximum temperature, strain rate, velocity and stress distributions are quite similar and differ by no more than 1-2 percent between the two composites indicating that the deformation behavior is primarily controlled by the matrix material and is not a function of the type of reinforcing ceramic particulates.

Jan 1, 2004

By C. H. B. Leitch

"The Bralorne-Pioneer deposit produced more gold than any other deposit in British Columbia over its 70 years of operation (130 kg or 4 million oz of Au, from 7 million tonnes of 18 glt ore). Mineralization is related to a suite of late Cretaceous albitite dykes of 85 to 90 Ma age. It thus occurred long after and is genetically unrelated to the Early Permian (275 Ma) Bralorne diorite and soda granite.The major veins strike about 110 degrees and dip north at 70 degrees, with slickensides plunging 45 degrees east that indicate last movement was reverse. Major ore shoots in the veins occupy somewhat less than 20% of the vein and plunge steeply west, roughly perpendicular to the slickensides. The structures that contain the veins probably formed at around 95 to 90 Ma during a strike-slip episode with easterly directed maximum compression.Disseminated pyrite, pyrrhotite, and minor chalcopyrite occur within envelopes up to several metres from the veins. Arsenopyrite is confined to vein selvages. Local sphalerite and galena appear to correlate with gold-rich portions of the veins. Traces of tetrahedrite and stibnite have been observed but tellurides have not. Gold is found principally as thin smeared flakes of the native metal in the black sulphidic septae of the strongly ribboned veins. Hydrothermal alteration envelopes around the veins grade outwards from intensely foliated quartz - ankerite - sercite (±fuchsite) to less sheared calcite - chlorite - albite to unsheared epidote -calcite.Open-space vein filling textures found in the deep (mesothermal) environment at Bralorne can be explained by a fault- valve model. High-angle reverse faults may have acted as fluid-pressure activated valves on geopressured reservoirs, causing large cyclic fluctuations in fluid pressure that promoted mineral deposition in an episodic fashion . The faults that were mineralized were reactivated sub-vertical former strike slip faults, oriented at a high angle to the northeast-directed stress in a compressive regime."

Jan 1, 1990

By C. O. Stee

IN the October, 1936, issue of the Canadian Mining Journal there was published a series of very comprehensive and exccellently illustrated papers by Mr. C. O. Stee and members of his staff dealing with Siscoe operations and ore-bodies. These were, in the order in which they appeared: Geology of Siscoe Gold Mine, by O. L. BACKMAN Diesel Power at Siscoe Gold Mines, Ltd., by C. O. STEE andE. A. BLOMQUIST Mining at Siscoe, by L. T. POSTLE and W. F. Engineering and Surveying, Siscoe Milling Practice, Research and Testing Laboratory, Assaying of Mill Tails and Solutions, BROWN(6) by P. A. TEEPLE (7) by L. E. DJINGHEUZTAN by L. RIVETT (8) by G. IRWIN (9) The Editor of the Canadian Mining Journal cordially assented to our suggestion that these papers be reviewed at the 1937 Annual General Meeting of the Institute, and the authors very kindly accepted our invitation to present such reviews . Of these courtesies, full acknowledgment is here accorded. To our readers, we commend the original papers in the Canadian Mining Journal. The summaries presented at the meeting follow. EDITOR. THE GEOGLY OF THE SISCOE MINE The Siscoe gold deposits lie in and near a stock of granodiorite, related to the Bourlamaque batholith, which has intruded highly folded Keewatin volcanic rocks .. The volcanic rocks lie to the north of a belt of Timiskaming sediments.

Jan 1, 1937

By D. K. Matlock, D. J. Hamre, J. G. Speer

Ultrafine ferrite (UFF) grains may be produced in surface layers of plate steels using controlled intermediate cooling followed by deformation. Experiments were conducted using a 0.12 C - 1.26 Mn steel on a Gleeble 1500 hot deformation simulator. Taguchi designed experiments were used to evaluate prior austenite grain size, intermediate cooling rate, intermediate cooling temperature, intermediate hold time and amount of reduction in order to observe the effects of variables and their interactions on the final microstructure while minimizing the number of required test runs. Evaluation of resulting microstructures and mechanical properties revealed a preferred thermal and mechanical history for developing ultrafine microstructures in surface layers of plate steels. Application of the fundamental concepts of phase transformations to industrial plate rolling is considered.

Jan 1, 2004

By P. Cicmanec

Mining activities in the territory of Slovakia have a long history. Mining techniques have developed rapidly in the last centuries. This paper deals not only with mining history, but also with underground brown coal mining, magnesite mining and other mining activities at present and sustainable developments of the mining industry in the Slovak Republic. This paper looks forward in the context of mineral raw materials in Europe (Global Europe, 2012).

Aug 1, 2013

By D. S. Salonine

Aluminum alloys offer a wide range of capability with a unique combination of advantages that makes them the materials of choice for numerous products and markets. One of the most important applications is their use as the primary structure and outer envelope in aerospace vehicles. Wide and thorough studies on hot working and microstructure evolution of aluminum alloys have been made in Russia. The most important appear to be: - introducing the structure diagrams in strain rate - temperature coordinates which show areas of different microstructures (non-recrystallized, recrystallized, and mixed) after the hot deformation and the following heat-treatment for common aluminum alloys (Yu.M. Vainblat); - studying the press-effect ("structural effect" by V.I. Dobatkin); - learning the influence of hot worked substructure on aging mechanisms; conducting researches on press heat-treatment. These works allowed a deeper understanding and a better control of the mechanical behavior of aluminum products. Comparisons are made to equivalent developments in Europe and America.

Jan 1, 2004

By F. E. Lathe

RECENT events have emphasized with renewed force the well known fact that war greatly intensifies the demand for certain metals, particularly for iron, copper, and zinc. Any increase in the use of iron and steel, whether in war or peace, is also accompanied by increased consumption of those metals which find their chief application as ferro-alloys, such as nickel, chromium, manganese, molybdenum, tungsten, and vanadium. Further, since high temperatures are essential for the production of all these metals, activity in the metal industry is inevitably accompanied by an insistent demand for refractories. For example, in North American practice the consumption of magnesitic hearth refractories is frequently expressed in pounds per ton of steel. This quantity (not including straight dolomite) ranges on individual plants from about 7 to 12 pounds. When the industry is operating at approximately full capacity, the ratio of refractory to steel tends to increase, since the tonnage of steel produced is recognized as of paramount importance, and this leads to the harder driving of furnaces and less regard for the effect on refractories. It should also be observed that the cost of refractories per ton of metal produced is always so low, in comparison with other items, that it may even increase while the cost of metal per ton is being reduced through more continuous operation and the use of higher temperatures. As one prominent Canadian copper metallurgist has tersely expressed it, he is "not in business to save refractories but to smelt ore". The effect of war demands and of general industrial activity upon the production of basic and neutral refractories is clearly shown in Figure 1, which gives the value of chrome ore and magnesitic-dolomite produced in Canada during the period 1907 to 1937. Tonnages have not been shown, as these are not available for the full period; such figures as have been published from time to time are not strictly comparable, since both raw rock and finished products have on occasion been included. The preliminary figures for 1938, which are now available, have been prepared by the Dominion Bureau of Statistics on a different basis from those immediately preceding, and have therefore not been shown.

Jan 1, 1940

By Lloyd W. Trevoy

Syncrude Canada Limited is presently studying commercial production of heavy minerals from plant tailings of the openpit A lhabasca tar sands operation. When tar sands are processed and upgraded to synthetic crude oil, heavy minerals can be removed f rom the extraction circuit and beneficiated to provide concentrates of zircon and titanium minerals. Calculated recovery rates indicate that crude oil production capabilities of 105,000 barrels per day would provide 26,000 tonnes of zircon and 114,000 tonnes of titanium minerals annually. The titanium minerals concentrate is a mixture of ilmenite, leucoxene and rutile; it could be used as recovered or upgraded to synthetic rutile. With the consrruction of further synthetic crude oil plants in Western Canada, a large reserve of heavy minerals will become available.

Jan 1, 1984

By G. M. Ritcey

The recovery of copper from low-grade solutions res ulting from dump leaching is well known, whereas the recovery from highly concentrated copper solutions has not been practiced. This paper discusses the use of Ashland Chemical's Kelex 100, a substituted quinoline, for the recovery of copper from solutions resulting from leaching copper-nickel concentrates. A flow sheet is described, and an economic comparison shows Kelex 100 to be superior to either the LIX 64N or LIX 70 reagents of General Mills for the recovery of copper.

Jan 1, 1973

By S. Shairp

"After cooling and thickening, slurry from the second stage of the Hudbay zinc pressure leach circuit is filtered and washed on a belt filter prior to disposal. At times, the belt filter can be a bottleneck to the process. Preliminary studies show that filterability of the second-stage (HAL) autoclave leach residue can be indicated by particle size distribution of the filter feed and filtered residue cake. In particular, the Volume Weighted Mean Diameter, D[4,3], generated by a laser diffraction particle size analyzer from samples of HAL Filter feed, shows residues that filter more poorly have a lower Volume Weighted Mean Diameter than those that filter better. INTRODUCTIONHudbay produces cast zinc metal from blends of zinc concentrates at its metallurgical complex in Flin Flon, Manitoba, Canada, using Sherritt’s two-stage pressure leach process (Collins et al., 1994; Collins et al., 1995; Barth et al., 1998; Shairp et al., 2006). Pressure leaching replaced the original roastleach- electrowinning process in 1993.Filtration for the second-stage (HAL) leach residue originally consisted of two stages of vacuum drum filtration with intermediate cake repulping stirred tanks. As part of Hudbay’s 777 Project, with a designed increase in cast zinc production, a pre-feasibility study by SNC-Lavalin Inc. showed that losses of soluble zinc in the zinc pressure leach residue could be reduced by installing more efficient filtering and washing equipment. Based on laboratory performance, capital cost, installation ability, and potential operating cost savings, a 70 m2 Filtres Phillipe belt filter was chosen for the HAL residue, and commissioned in 2000/2001.When the HAL belt filter is performing well, there is no pooling of water on the surface, moisture content is relatively low, and subsequent analysis shows that water soluble zinc content is relatively low. There have been occasions where the filter has performed poorly with respect to the aforementioned parameters. Aside from the filter experiencing mechanical difficulties, there are several variables affecting leach residue filtration:"

Jan 1, 2012

By A. G. Roach

HISTORY AND LOCATION SEAL HARBOR GOLD MINES, LIMITED, was incorporated in January, 1934, to take over 116 acres of mining lands in the Stormont gold district, Guysboro county, Nova Scotia. The nearby ten-stamp Mulgrave mill was also purchased, and since that time 974 acres of adjoining properties have been secured from the Government by direct lease. The property is served by a motor road and is about two miles from the village of Goldboro, situated on the shore of Isaac's harbour. The bulk of ?the supplies are brought in by coastal steamer from Halifax, a distance of about 100 miles, since the nearest railway connections are at Antigonish, some 40 miles distant. EARLYY WORK The Seal Harbor properties include the old Partington and Beaver Hat mines. A small tonnage of ore was mined from each and treated on the properties in stamp mills, which were later torn. down . A survey of old records shows that this ore averaged about $8.00 gold per ton. Development work by the present Company was confined to the 100-foot level until February, 1935, but after that rime the incline shaft was deepened to 425 feet and the 300-foot level was explored east and west of the shaft. Six belts of ore were intersected to the west of the shaft. The ore from these belts was hand sorted and the ore portion was put through the 10-stamp Mulgrave mill to defray operating expenses and to serve as a sample of the deposits. The average recovery per ton from this sorted ore was $6.10. Samples of the ore were sent to the testing laboratories of the Mines Branch, at Ottawa, and of Canadian Industries, Limited, at Toronto. Recommendations from both of these authorities were for removal of the coarse gold by concentration and barrel amalgamation, followed by cyanidation of the residue.

Jan 1, 1937

By Tanai Marin

Modelling of pyrometallurgical processes can become extremely challenging when the process involves complex chemical reactions, phase change, multiphase flows, heat and mass transfer and fluid flow. Traditionally modelling involving complex thermodynamic equilibrium and thermochemistry are treated separately from problems in which transport phenomena are dominant, such as CFD and heat transfer studies. The separation is also necessary due to the lack of modelling tools that can effectively couple both solution thermodynamic and transport phenomena or even multiphysics problems. However, there are, quite often, problems in high temperature process metallurgy in which it is not possible to simplify this two modelling approaches. Typical cases of this are for example, the modelling of slag freezing on furnace walls (electric or flash furnaces) to create a protective layer in front of the refractories hot wall, the formation of build up from the matte or metal phases at the hearth of the furnace, calcine smelting from charging piles into slag phase, etc. The problem is even more challenging in nonferrous pyrometallurgy as most, if not all, of the condense phases are highly non ideal solutions involving several components and exhibiting complex crystallization paths and miscibility gaps, such as the Fe-Ni-Cu-S matte, FeO-Fe2O3-SiO2, FeO-MgO-SiO2 slags, etc. In this paper, an approach to model coupled problems involving multiphysics and solution thermodynamic is presented. The approach consists in developing in-house a library containing the Gibbs energy minimization routines and using the local equilibrium concept for process modelling from a multiphysics commercial software (COMSOL). Simple test cases, such as building a non-ideal binary phase diagram on a CFD package is presented, the limitations and of other classic approaches such as equilibrium or Scheil cooling are discussed and compared to this model.

Jan 1, 2015

By G Anders

The mucking out of sub-level headings by slusher and by Autoloader is described, and the performance and costs of both methods are compared. The introduction of the Autoloader is taken as an example to illustrate the meth-od used at the mine for evaluating the suitability of new equipment. The consecutive steps in the process are covered in detail -from the preliminary cost analysis and the preliminary estimate of savings and advantages, and the review of these data after a field investigation, through the elimination of dubious factors, and detailed time and performance studies at the property, to the final assessment of the new equipment and an evaluation of the initial forecast. The Autoloader in Operation. 1198 Introduction AT Mattagami Lake Mines Ltd., the mine workings are laid out basically on a pattern of 60-ft.-wide stapes alternating with 60-ft.-wide pillars, with stope lengths varying from 80 to 200 ft. and stope tonnages generally between 80,000 and 200,000 tons. Stapes are drilled off from sub-levels at 60-ft. intervals, with the

Jan 1, 1965

By Mingxia Liu, Hao Li, Qi Liu

"Laboratory batch flotation tests were carried out on fine (-20 µm) hematite to investigate the non-polar oil’s influences when sodium oleate, octyl hydroxamic acid, or oleyl hydroxamic acid were used as a collector. Batch flotation tests were performed with artificial mixed minerals (hematite:quartz = 1:1) under natural pH condition and kerosene was utilized as the model oil. The experimental results showed that kerosene emulsion behaved differently when used in conjunction with the three collectors. Kerosene helped improve the flotation when sodium oleate or oleyl hydroxamic acid was used as a collector. Nevertheless, it reduced concentrate weight yield, grade and recovery to a noticeable extent when octyl hydroxamic acid was used as a collector, especially at low dosages. In addition, single hematite batch flotation kinetics tests coupled with water recovery measurement were carried out to study the role of kerosene at different collector dosages. It was observed that water drainage and the resulting froth destabilization by kerosene was dominant at low collector dosages, especially in the flotation using octyl hydroxamic acid. At higher collector dosages, the water drainage and froth destabilization effect by kerosene was possibly counter-balanced by the higher hematite hydrophobicity and bubble surface tension gradient, which led to more stable froth layer.INTRODUCTION The minerals industry is facing a steady decline in ore grade, compounded by increasing complexity of mineral dissemination. As a result, the ore has to be ground sufficiently fine to have a suitable degree of mineral liberation, which produces large percentages of fine and ultrafine particles outside of optimal size range for ore dressing. Due to the unique characteristics of fine particles, i.e., small mass, high specific surface area, and problems such as increased solubility of complex minerals (Finkelstein, 1997; Finkelstein & Allison, 1976; Fornasiero & Ralston, 2005), high reagent consumption, fast surface oxidation in the case of sulfides (Collins & Read, 1971; Klassen & Mokrousov, 1963), severe particle entrainment (Subrahmanyam & Forssberg, 1988; Warren, 1984), low flotation rates (Glembotsky, 1953; Philippoff, 1952; Ye & Miller, 1988), slime coating (T. K. Mitchell et al., 2005; Parsonage, 1984), etc., flotation performance of these finely ground ores is very poor in terms of low concentrate grade and recovery."

Jan 1, 2017

By D. Fodor

In Romania, there are significant lignite and brown coal reserves hosted by different regions of the country. The most important lignite bearing zone of the country situated in the North ? West part of Oltenia region and which covers a surface area of 2,500 km2 and host a total reserve of 3.0 billion tons of lignite, of which more than 95% can be exploited by open cast method. The paper deals with the existing geological and mining conditions of the zone , the distribution by mining basins and exploitation perimeters, the open cast working technologies and the economic outcomes obtained throughout the time. Years ago, for the improvement of the economic situation as a whole and in each unit, a large production reorganization, technology update and modernization process was started up. There are described the rehabilitation measures of the technological lines and modernization of the equipments of the production flow-sheet, measures developed at present, too and which will still continue in future. There are mentioned the equipments considered, the components under modernization and the economic outcomes obtained so far. At the end of the paper there are presented the future actions for the equipment modernization and perspectives of the lignite deposit exploitation to meet the national economy requirements of solid fuels.

Aug 1, 2013

By J. Dong

"A “green” collector project has been initiated at Vale Base Metals Technology Development to replace xanthate. Bench and miniplant testwork showed comparable metallurgical results between xanthate and DTC (sodium dibutyl dithiocarbamate), a “greener” collector. During the first DTC plant trial, a strong interaction between the process water and DTC negatively impacted the metallurgy. The subsequent investigation showed that the quality of process water including suspended solids and dissolved metal ions had a significant impact on the performance with DTC, while less so with PAX. This paper explains these differences using UV spectrophotometry and batch flotation tests. INTRODUCTIONVale Base Metals is dedicated to sustainable mining and mineral processing. One of the key activities is to find a “greener” collector to replace xanthate (PAX: potassium amyl xanthate), which decomposes during storage and flotation causing CS2 emissions in the work place. As the most promising candidate, DTC (sodium dibutyl dithiocarbamate) was evaluated in the lab and miniplant (Dong & Xu, 2011). Consequently, a plant trial was conducted in the winter of 2010. However, the results were not as good as expected. The subsequent investigation showed that the quality of process water played a significant role in the metallurgical performance with DTC but less so with xanthate.From test work in 1996 and 1997, a series of batch tests were performed at Clarabelle Mill to investigate the winter/summer metallurgical shift with xanthate. As shown in Figure 1, the winter metallurgy was considerably worse than the summer metallurgy (Xu & Wilson, 2000). At 80% pentlandite recovery, the concentrate (Cu+Ni) grade was 21% in the winter and 26% in the summer. At 23% (Cu+Ni) concentrate grade, pentlandite recovery was 85% in the summer and 70% in the winter. In the summer, the process water is much cleaner, with very low concentrations of dissolved metals ions and suspended solids; while in the winter, the water is yellow and cloudy, with much higher suspended solids. Based on these results, it was concluded that the process water in winter has a detrimental impact on metallurgy."

Jan 1, 2012

By M. Dupuis

In the present study, the heat balance of the Hirakud smelter aluminium reduction cell has been accurately assessed using only a surface thermocouple and a pyrometer, As it is well known that using a single linear or quadratic relationship to estimate the heat flux from the measured surface temperature does not provide the accuracy required to close the cell heat balance, this approach was not used in this study, Instead, the fundamental natural convection and radiation heat flux equations were used systematically for each measurement point, Practically, this means that the ambient air temperature and at least one ambient radiative temperature must also be known in addition to the surface temperature for each measurement point. Sometimes, the radiative heat flux could not be accurately estimated using a single ambient radiative temperature, In those cases, a more accurate estimation based on two ambient radiative temperatures and corresponding view factors has been used instead, It turns out that although at least three temperature measurements are required to estimate a single heat flux, it takes a lot less time to make those temperature measurements using a pyrometer than directly measuring the heat flux using an expensive heat flux meter, Furthermore, no loss in accuracy was detected when using this approach as the cell heat balance could be closed within 5%, the level of accuracy typical of cell heat balance assessment using heat flux meter.

Jan 1, 2004

By J. Lui

At its Copper Cliff Smelter, bulk nickel and copper concentrate is processed in two Inca flash furnaces and Peirce Smith converters to produce Bessemer matte containing 0.6%Fe. After slow cooling and Matte Separation, Bessemer matte is converted into three main products using magnetic separation and flotation technology: (1) a nickel containing chalcocite concentrate (MK); (2) two types of copper containing nickel sulfide (ME and MR); (3) metallics (MYN). MK is further processed in the Inca top blowing bottom stirring MK Reactor to produce semi-blister copper containing ~4%Ni and ~3±1 %S. The semi-blister copper is then purified in the multi-purpose vessels (MPV) to produce blister copper by reducing Ni, Fe and S content through oxidation. High melting point NiO is formed inside the MPVs. The accumulation of solid NiO and other oxides requires periodic cleaning by adding reductant and furnace matte, a unique process called "washout" at Inca. For many years, the reductant used for the "washout" process has been 15%Si Ferro-silicon. With increasing cost and limited suppliers for 15%FeSi, alternative reductants were pursued. This paper summarizes the development and commercialization of new alternative reductants for MPV "washout".

Jan 1, 2007