Search Documents

By Anthony Sharkey

Introduction In Europe, longwall mining accounts for over 95% of coal produced from deep mines, whereas in the U.S.A., longwall accounts for less than 5% of deep mine coal production. There are many reasons for the difference, but in general: a. U.S. mine operators have invested heavily in continuous mining or conventional equipment which continues to produce acceptable results; b. There 1s a reluctance to change from, a familiar (and proven) mining method to an unfamiliar one, despite promises of huge production increases,; c. Multi-seam mining in Europe has made longwall the only really viable mining method, whereas In the U.S.A. multi-seam mining (particularly in "below-drainage" mines), is relatively rare; d. Although some spectacular results have been achieved by longwall in the U.S.A.(I), the general performance of longwall in this country has not been good enough to generate much enthusiasm for its wide application; e. The much higher level of investment in face equipment required for longwall when compared to alternative methods (approximately $7.5 million for a medium seam longwall installation and $1 million to $1.5 million for a continuous miner section). However, declining productivity, national energy requirements and safety legislation are creating a situation in which longwall as a viable mining method is being examined more closely and in more places than hitherto. This paper, therefore, attempts to identify some of the principal criteria needing examination in any assessment of the feasibility of longwall application, the limitations of information for those criteria in the decision making process and the need for further research and development to assist the mine operators make the decisions.

Jan 1, 1981

By Mark D. Zoback, Bezalel C. Haimson

INTRODUCTION A Workshop on Hydraulic Fracturing Stress Measurements was convened by the authors in December 1981 in Monterey, California under the auspices of the U.S. Geological Survey and the U.S. National Committee on Rock Mechanics. There are now over a dozen groups of investigators around the world who are actively using the hydraulic fracturing method for making in-situ stress measurements. Because of the extensive recent experience of these different groups, the Workshop enabled forty investigators from eight countries to comprehensively assess the status of the method. Based on the presentations and discussions at the Workshop, in this paper we briefly discuss the current status of the hydraulic fracturing stress measurement method concentrating on problem areas where further research needs to be done. A complete account of the presentations at the Workshop will be available through the Proceedings of the Workshop which will be published by the U.S. National Committee on Rock Mechanics in early 1983. The most exciting aspect of the Workshop was the discovery by the various groups of investigators that others were having very similar experiences with the method. The consensus among the different groups of investigators at the Workshop was that they were recording very similar pressure-time data in the field, they were able to interpret them in similar ways, and they were achieving results that were quite encouraging because of several factors. First, the results at various locales were found to be internally quite consistent. This was reported by investigators from Germany (Rummel, Baumgartner, and Alheid, 1982), Japan (Tsukahara, 1982), Australia (Enever, 1982), and the U.S. (see, for example, Haimson, 1978, 1982a; Zoback

Jan 1, 1982

By George Sachs

I deeply appreciate the honor of being selected to deliver the twentieth Annual Lecture of the Institute of Metals Division. The subject of my paper is extremely involved and voluminous, therefore I shall discuss only some more recent experimental material and speculate somewhat on the physical and mechanical fundamentals of these changes. The flow and the rupture of a solid material are rather different phenomena. It is therefore surprising that up to a rather advanced stage in metallurgical science these two fundamental phenomena have been simultaneously treated and forced into the general conception of the "failure" of solid material. Only in this century, and particularly during the last 20 years, have the very different physical meanings of flow and rupture been clearly recognized. Several hundred of the more recent publications deal with these subjects.1 LAW OF SIMILARITY The basic values commonly considered responsible for the mechanical behavior of any material are the stresses. From this standpoint both a large and a small article made from the same homogeneous metal and of geometrically similar shapes should behave identically, i.e., they should deform geometrically in a similar manner, if subjected to the same stress values at corresponding points. This "law of similarity" was introduced about 60 years ago simultaneously by Barba2 and Kick3 and was derived from the classical theory of elasticity. As far as the plastic behavior of a metal is concerned, this rule appears to be valid. The conventional properties of large and small tension or compression test bars, machined from larger sections, are identical; while the force required to deform a section is proportional to its cross-sectional area and the work consumed in deforming geometrically similar articles in a geometrically similar manner is proportional to its volume. The general trend of the stress-strain diagram of a metal is independent of the section size (Fig. I). No exceptions from this rule are known. However, if the deformation of a metal is continued until rupture occurs, and the breaking stress or the work consumed is measured, a test bar of large cross section appears to fail before or at lower stresses than does one having a small cross section. Thus, the specific impact energy has been often found to decrease with increasing size of the test specimen, particularly for materials with a limited ductility.4 Another exception from the rule of similarity is offered by fatigue-strength values, which usually decrease with increasing section size. 5,6 The conclusion must be drawn from these experimental facts that the ductility of a homogeneous metal decreases with increas¬ing section size (Fig. x). This effect has been actually confirmed by Docherty,7 who observed that in static notch bending tests large specimens failed earlier and in a more brittle fashion than small specimens ma-

Jan 1, 1941

By R. J. Wygal, J. Naar

An equation for three-phase (water, oil, gas) imbibition oil permeability is developed, assuming the water to be the dominant wetting fluid. Oil isoperms are obtained for consolidated sandstones characterized by 1/pc2 = CS*. The evolution of an oil-gas system imbibing water from Swi to(Sw,imb )max is shown to proceed along a line of constant oil saturation with increasing oil permeability and decreasing gas saturation. When the gas satuation cannot be reduced further, the system evolves along a line of constant Sg with decreasing oil saturation and permeability. The initial gas saturation is shown to reduce markedly the effect of complete wetting by either oil or water on flow performance. INTRODUCTION Imbibition oil isoperms are required for performance prediction when a well is producing water, oil and gas. This situation occurs in multiphase displacements such as underground combustion, steam injection and the water flooding of highly depleted reservoirs. In a recent paper,1 a model was presented for the prediction of two-phase imbibition characteristics. This paper extends the imbibition model to the case of three phases by assuming that the water is the dominant wetting fluid. The following results were obtained from the model: (1) an analytical expression of oil isoperms; (2) oil isoperrns as functions of reduced water, oil and gas saturations, valid for all sandstones having a capillary pressure curve which can be approximated by 1/PC = CS*; and (3) evaluation of the three-phase flow performance as dictated by complete wetting by either oil or water. The agreement between predicted and observed oil recovery in the presence of a gas phase, reported in Ref. 1, is a partial support for the present development. However, experimental data are not available at this time to check fully the model predictions. Perhaps this paper will stimulate the collection of such data. The imbibition model of a porous medium has been described previously, and the reader is referred to the paper of Naar and Henderson1 for details. In brief, the model is formed by the random interconnection of straight capillaries, with a provision for the blocking of the non-wetting phase by the invading wetting fluid. The following expressions were derived from the model. 1. The amount of oil blocked by the invading water is

By R. P. Carreker, J. G. Leschen, J. H. Hollomon

THE external appearance of a crystal which has undergone plastic flow suggests that adjacent blocks of the crystal have glided bodily past one another along the slip planes. However, the great discrepancy between the shear stresses calculated to effect such a movement and those actually observed has for many years stimulated searches for more satisfactory interpretations of the slip process. Appreciable success in these efforts has been realized by assuming the presence in the crystal of various sorts of imperfections and by considering the consequences of the presence of these flaws when stress is externally applied, The theory that has received the most attention recently-that of dislocations-postulates the occurrence of small, mobile imperfections or dislocations which move through the crystal along the slip direction, each dislocation being attended by a local shear displacement of one interatomic distance. Thus only that portion of the crystal through which the dislocation has passed may be said to have slipped, Since each dislocation produces a displacement of only one interatomic distance, an avalanche or train of many dislocations would be necessary to account for the observed displacements of several hundred or thousand interatomic distances. The salient point of the theory of dislocations is the concept that a slip band does not suddenly appear in its entirety. On the contrary, it grows progressively across the slip plane as the individual dislocations successively appear and advance in a train through the crystal. However, the concept of growth is not intrinsic only to the theory of dislocations, since atomistic mechanisms other than that postulated by the dislocation theory can quite probably also describe the growth of a slip band. For instance, a slip band might resemble a disc-like interface that appeared and then grew continuously from a small size, producing a displacement that increased with the size of the disc, Whatever the precise mechanism, the concept of growth is in itself consistent both with -the observed low values of critical shear stress and with the experimental observation that slip bands. frequently do not traverse the entire crystal. The likelihood that slip bands grow implies that they must first be nucleated and that the initiation of slip can therefore be analyzed in terms of the general concepts of nucleation. Indeed, this suggestion was advanced1 several years ago, but the matter does not appear to have been further pursued. Recent advances in the theory of nucleations2,3,4 have encouraged such a treatment of the slip process. As will presently be demonstrated, this approach to the problem not only accounts successfully for the incubation periods that have been observed5,6 to precede slip but also predicts certain transient effects in the deformation process, The existence of these transients apparently has not hitherto

Jan 1, 1948

By R. P. Carreker, J. G. Leschen, J. H. Hollomon

The external appearance of a crystal which has undergone plastic flow suggests that adjacent blocks of the crystal have glided bodily past one another along the slip planes. However, the great discrepancy between the shear stresses calculated to effect such a movement and those actually observed has for many years stimulated searches for more satisfactory interpretations of the slip process. Appreciable success in these efforts has been realized by assuming the presence in the crystal of various sorts of imperfections and by considering the consequences of the presence of these flaws when stress is externally applied. The theory that has received the most attention recently—that of dislocations—postulates the occurrence of small, mobile imperfections or dislocations which move through the crystal along the slip direction, each dislocation being attended by a local shear displacement of one interatomic distance. Thus only that portion of the crystal through which the dislocation has passed may be said to have slipped. Since each dislocation produces a displacement of only one interatomic distance, an avalanche or train of many dislocations would be necessary to account for the observed displacements of several hundred or thousand interatomic distances. The salient point of the theory of dislocations is the concept that a slip band does not suddenly appear in its entirety. On the contrary, it grows progressively across the slip plane as the individual dislocations successively appear and advance in a train through the crystal. However, the concept of growth is not intrinsic only to the theory of dislocations, since atomistic mechanisms other than that postulated by the dislocation theory can quite probably also describe the growth of a slip band. For instance, a slip band might resemble a disc-like interface that appeared and then grew continuously from a small size, producing a displacement that increased with the size of the disc. Whatever the precise mechanism, the concept of growth is in itself consistent both with the observed low values of critical shear stress and with the experimental observation that slip bands frequently do not traverse the entire crystal. The likelihood that slip bands grow implies that they must first be nucleated and that the initiation of slip can therefore be analyzed in terms of the general concepts of nucleation. Indeed, this suggestion was advanced1 several years ago, but the matter does not appear to have been further pursued. Recent advances in the theory of nucleation 2,3,4 have encouraged such a treatment of the slip process. As will presently be demonstrated, this approach to the problem not only accounts successfully for the incubation periods that have been observed 5,6 to precede slip but also predicts certain transient effects in the deformation process. The existence of these transients apparently has not hitherto

Jan 1, 1949

By George S. Rice

THE year 1929 has shown a surprising growth in the attention given by mining men to the subject of ground movement and subsidence from mining, as evidenced by the large number of articles that have appeared in technical journals, also papers and discussions in mining societies in the leading mining countries of the world. These have not been confined to consideration of the narrower limits of the subject but in application have extended to many of the fundamental questions involved in mining. The papers and discussions have been concerned with .ground movements resulting from mining of a great variety of minerals, metallic and lion-metallic. Examples of the former are: the mining of gold ore at Johannesburg, South Africa, and in the Kolar field, India; mining copper ores in Arizona and Utah; and lead and zinc in the Joplin region. Examples of ground movement resulting from mining non-metallic minerals are found in: the mining of. coal in many countries; potash mining in Germany; the mining of- common salt in several parts of the' United States; and the mining of sulfur in Texas and Louisiana; and examples of subsidence in the non-metallics are found exceptionally in the extraction of petroleum by wells, as in the Goose Creek field, on the Gulf Coast,' and recently in the Sour Lake field' of Texas

Jan 1, 1930

By M. C. Flemings, R. Mehrabian, G. E. Nereo

Analytic expressions were developed and applied in two preuious papers to predict effects of solidification variables on macrosegvegation. In this paper, experiments are reported to test the analyses quantitatively and qualitatively. Good quantitative agreement is obtained between predicted and measured compositions for the following types of segregation (all experiments were on laboratory-size ingots of Al-4.5 pct Cu alloy): (a) inuerse segregation, (b) composition distribution in ingots solidified with unidirectional heat and fluid flow, (c) simulated centerline segregation, and (d) segregation resulting fro, change in solidification cross section. In addition, qualitative agreement of prediction of theory with experiment is obtained for (a) segregation resulting from sudden change in heat extraction during solidification, (b) centerline segregation in a bidirectionally solidified ingot, and (c) under-riser positive segregation. IN two previous papers,''2 it was shown that a variety of apparently different types of macrosegregation result from the same basic mechanism. This mechanism is the flow of solute -rich liquid to feed solidification and thermal contractions. Analytic expressions were derived and examples given of their application to predict macrosegregation. Calculations were for Al-4.5 pct Cu alloy. In this paper, we describe a series of experiments designed to test results of the foregoing calculations. All experiments were on laboratory-size ingots (weighing 10 lb or less), of A1-4.5 pct Cu alloy, nominal composition. APPARATUS AND PROCEDURE A typical mold and chilling arrangement used for unidirectional solidification is shown in Fig. 1. Before casting, this assembly was placed in an electrically heated air furnace, and heated to 680" to 700°C. When the plaster reached the desired temperature (usually 1 to 2 hr after the furnace temperature), the mold was filled through a funnel extending from the outside of the furnace into the cavity. The assembly, with liquid, was held for several minutes to allow convection to subside. The coolant, either air or water (depending on the desired solidification rate), was turned on and the ingot solidified. With the four sides and top insulated, heat removal for solidification was through the bottom surface, resulting in a fully columnar structure. Design of the casting cavity was varied, as discussed below, to produce desired macrosegregation effects. However, for castings solidified with unidirectional heat flow, the top was always open to the furnace atmosphere and temperature. The bottom sur- face rested on a chill through which the heat was extracted, and all other surfaces were insulated with plaster. In one case to be discussed, the mold design was changed to obtain bidirectional solidification. In this case, two vertical chills were used (on two faces of the mold) and the bottom was insulated. In a last case discussed, that dealing with under-riser segregation, experiments were conducted in bottom-chilled sand molds at ambient temperature. Except for this one case, all experiments were conducted in the electrically heated air furnace as described above. In many ingots, thermocouples were used to obtain continuous records of solidification. In all cases, these were chromel-alumel couples with output continuously monitored on a twelve-channel recorder. Where thermocouples were employed, these were embedded in the refractory mold walls during mold-making so their heads extended to the vertical centerline. Six to nine couples were employed, placed at intervals from the chill. METAL-MEL TING PROCEDURE Aim analysis was A1-4.5 pct Cu; alloy was prepared from high-purity aluminum (99.9 pct Al) and A1-Cu master alloy (50 pctOFHC Copper, 50 pct high-purity Al). The A1-4.5 pct Cu alloy was cast in 5- to 7-lb ingots for subsequent remelting for the macrosegregation experiments. Melting for ingot casting was as follows. After preheating the melting crucible for an hour or more, the charge was melted and superheated to a temperature of 690" to 720°C. After stirring, the melt was degassed with chlorine for 10 min. After stirring again for 1 min, a gas sample, under reduced pressure, was taken. When the sample was gas-free, the crucible

Jan 1, 1969

By Mark David Rankin

This paper represents a general assessment of the primary factors driving the market for mobile offshore drilling rigs and the utility of those factors as choice variables for the offshore drilling program planner.

Jan 1, 1982

SAMUEL L. HOYT.-The question of adding the ferromanganese to the ladle or to the furnace involves both theoretical and practical questions and its discussion might very easily occupy the rest of the day. One of the points to be kept in mind is the desirability of obtaining uniform steel. If ferromanganese is added to the ladle, it is necessary first to melt the manganese and then to distribute uniformly throughout the heat. The only heat available for this purpose is that of the molten steel itself. No doubt sufficient heat is present, but in our desire to pour the steel as quickly as possible there is hardly sufficient time allowed, many times, for the proper distribution of the manganese. In other words, this is an operation which takes a certain amount of time and any undue shortening of the time allowed must affect the quality and uniformity of the steel. Again, this particular method does not lead to as efficient a use of the manganese as might be desired; a contention which is based on theoretical grounds. In concentrated solution, manganese will completely reduce all the ferrous oxide, the presence of which I hypothecate and produce, as the reaction product, manganese oxide. In dilute solution, the manganese only partly reduces the iron oxide, but the manganesee oxide which does form dissolves the iron oxide in simple solution. The dissolution of ferrous oxide in the manganese oxide will result in a more economical utilization of the manganese and an equal purification of the heat. This whole point, at present, has not been definitely proved and its answer will involve very difficult research work. On the other hand, if the manganese is added to the furnace, the heat of the furnace is used to melt the alloy and there is plenty of time during tapping for the manganese to be very uniformly distributed throughout the steel. By distributing the alloy throughout the charge we can secure a better utilization of the manganese than is possible if the addition is made to the ladle. Certain other points, such as the recovery, have been dealt with at greater length in the paper.

Jan 4, 1919

By J. M. Tobin, L. H. Cadoff, L. M. Adelsberg

The reaction between liquid zirconium and graphite at temperatures above 2000 °C has been investigated. The reaction products were found to be carbon-saturated zirconium metal and ZrC which formed between the graphite and the metal. Parabolic growth behavior was observed for the ZrC Phase at all temperatures of this investigation. The parabolic growth constant at temperatures between 2000° and 2860°C was measured to be 1.83 exp 84,300/RT) sq cm per sec. The reaclion mechanism was proposed to be the rapid carbon saturation of the liquid metal and the formation of ZrC at the metal-carbide interface with diffusion of carbon through the ZrC, the "rate - determining step" of the reaction. The concentration-independent diffusion coefficient of carbon in ZrC, (DZrC), was expressed as 0.95 exp? 78,700/RT) sq cm per sec. This value mas calculated using the temperature-invariant ZrC phase fields proposed in the literature. The [ZrQiq)] — [ZYQiq) + ZrC] phase boundary over the temperature range 2000° to 2800°C was determined and the ZrC + C eutectic temperature was found to be 2890° ± 50°C. ThE Group IV and VB transition-metal refractory carbides are of interest because of their high melting points, high temperature strength properties, and relative inertness in certain corrosive environments. The present-day understanding of these materials, however, is limited by the general unavailability of accurate and reliable physical and chemical property data. This is due primarily to the difficulties associated with the preparation of suitable, high-density, high-purity carbide samples, and the achievement and control of uniform high-temperature environments. Accurate measurement of temperature is also an important factor limiting the reliability of reported data. The Zr-C reaction was selected for investigation because of the high melting point (>34000C) and favorable nuclear properties of the reaction product, ZrC. The direct reaction method afforded an opportunity to obtain kinetic data on the fully dense carbide. In this paper, layer-growth techniques were used to estimate the diffusivity of carbon in ZrC and to investigate the phase equilibria in the Zr-C system at temperatures above 2000°C. EXPERIMENTAL PROCEDURES AND DATA Crystal bar zirconium (99.9 pct Zr), purchased from the Nuclear Materials and Engineering Corp., and ZTA graphite (99.9+ pct) were used in this study. The analyses of the materials are listed in Table I. A schematic of the high-temperature carburization apparatus is shown in Fig. 1. The sample was a zirconium metal charge in a 1/2 -in.-ID graphite crucible which was capped with a tightly fitting graphite stern. The crucible and stem were designed to closely approximate black-body conditions. The graphite crucible was packed in lampblack (outgassed 1 hr at 2100°C) which provided insulation and thermal stability to the system. The inert atmosphere was maintained by a constant flow of high-purity argon or helium gas. The nozzle-diffuser section on the top flange was sufficient to prevent back-diffusion of air into the system. Chemical analysis of the carburized samples revealed oxygen and nitrogen concentrations of less than 44 and 20 ppm, respectively. The sample was heated by induction with a Westing-house 5 kw-450 kc power source. Temperature was measured with a Milletron two-color pyrometer which was sighted into the crucible by reflection from an overhead front surface mirror. Optical losses due to glass absorption and light reflection at air-glass interfaces were minimized by the employment of the dynamic-gas seal. It was found that no correction was required for the front surface reflector. The pyrometer was calibrated periodically against a U.S. Bureau of Standards tungsten ribbon secondary standard. Temperatures inside the crucible were also calibrated against the Zr-ZrC eutectic (1850°C)1 and the Nb-Nb2C eutectic (2335°C)2,3 temperatures and agreed to within ±10°C of these values. The temperature was controlled by manually adjusting the power input; variations of

Jan 1, 1967

By R. A. Vandermeer, J. C. Ogle

The preferred crystallographic orientations (texture) developed in randomly oriented, poly crystalline niobium during rolling were studied by means of X-ray diflraction techniques. The evolution of texture at both the surface and center regions of the rolled strip was carefully examined as a function of increasing defamation throughout the range 43 to 99.5 pct reduction in thickness. Certain aspects of the center texture development in niobium are in agreement with the predictions of a theory by Dillamore and Roberts, but others cannot be explained by the theory in its present form. Above 87 pct reduction by rolling, a distinctly different texture appeared in the surface layers which was unlike the center texture. The present results are compared with previous results obtained from other bcc metals and alloys. RANDOMLY oriented, poly crystalline metal aggregates when plastically deformed to a sufficiently large extent develop preferred orientations or textures. In a recent review article, Dillamore and Roberts1 pointed out that the nature of the developed texture may be influenced by a large number of variables. These include both material variables such as crystal structure and composition and treatment variables such as stress system, amount of deformation, deformation temperature, strain rate, prior thermal-mechanical history, and so forth. From a practical point of view, the control of preferred orientation may often be important for the successful fabrication of metals into usable components. During the past few decades many experiments have been devoted to the study of deformation textures. This work, however, has been confined in large part to metals and alloys that have an fcc crystal lattice. By comparison, bcc metals and alloys have received much less attention, and consequently our understanding of preferred orientations in these materials is only shallow. This state of affairs worsens when it is realized that almost all of our present howledge about this class of materials derives from studies on irons and steels.' The bcc refractory metals, which are relative newcomers to the industrial world, have, on the other hand, been given at best only passing glances in the area of texture development. Our understanding of the evolution of preferred orientations in bcc metals can only remain fairly limited until systematic studies of metals and alloys other than the irons and steels have been carried out and the influence of the many variables has been determined. To that end a program was initiated to investigate in detail texture development in niobium. The present paper reports some of the results of this study. Textures were determined at both the center and surface of strips rolled variously to as much as 99.5 pct reduction in thickness at subzero temperatures. Emphasis in this paper is on texture description and on texture evolution during rolling to progressively heavier deformation. EXPERIMENTAL PROCEDURE The niobium was purchased from the Wah Chang Corp. as a 3-in.-diam electron-beam-melted billet. Chemical analysis indicated the impurities to be less than 300 ppm Ta, 40 ppm C, 10 ppm H, 170 ppm 0, and 110 ppm N. All other impurities were below the limits of detection by spectrochemical analysis. This large-grained billet was fabricated into specimen stock so that a fine-grained randomly oriented grain structure resulted. This was accomplished in three deformation steps alternated with recrystalli-zation anneals of 1 hr at 1200°C in a vacuum of low 10"6 Torr range after each deformation step. The first step was to alternately compress the billet 10 to 20 pct in each of three orthogonal directions. The second step was to compress in only two directions 90 deg apart to produce a 2-in.-sq bar. The final step was to roll this bar 50 pct to give a 1-in. by 2-in. cross section. After the final anneal, metallo-graphic examination showed the material to have an average grain size equivalent to ASTM No. 5 at 100 times (i.e., 0.065 in. diam). Specimens cut from the center and edges of this bar gave no indication of detectable preferred orientation when examined by X-ray diffraction. Samples 1.5 in. long, either 0.625 or 0.750 in. wide, and approximately 0.400 in. thick were machined from this fabricated ingot. The surfaces corresponding to the rolling planes were ground so as to be parallel. The samples were chemically polished in a solution of 60 pct nitric acid and 40 pct hydrofluoric acid (48 pct solution) prior to rolling to remove any cold work introduced in the machining operations. Rolling was accomplished with a 2-high hand-operated laboratory rolling mill that had 2.72-in.-diam rolls. Prior to operation, the rolls were polished with 600 grit paper, cleaned with acetone, and then soaked in a container of liquid nitrogen for several hours. The samples were also soaked in liquid nitrogen prior to rolling and were recooled between each pass. While some slight heating of the samples occurred during rolling, this procedure maintained the sample temperature well below 0°C at all times. The samples were rolled unidirectionally, and the rolling plane surfaces were not inverted during any phase of the operation. The draft per pass averaged between 0.010 to 0.012 in. After 96 or 97 pct reduction the draft was reduced to 0.001 to 0.002 in. per pass. Samples were rolled to various reductions in thickness between 43 and 99.5 pct.

Jan 1, 1969

By T. D. Tiemann

The chemical and mineralogical composition of Caribbean bauxite ores are described. Extraction of alumina by several processes from both Haiti and Jamaica bauxites is discussed and data presented. IMMENSE deposits of bauxite occur in the Caribbean islands of Hispaniola and Jamaica in the high plateau lands and have been excellently described by 0. C. Schmedeman.' The bauxite occurs as deposits in catchments or etched depressions in Tertiary limestone believed to have been deposited in the Eocene and Oligocene periods.' In appearance both the Haiti and Jamaica bauxites resemble a relatively high iron clay and have indeed been mistaken for such.' They are very soft and friable and disperse readily on vigorous agitation in water. The color range in general is light brown to red. Chemically, the outstanding characteristic of the bauxites is the low silica and high ferric oxide content. The extremely low silica makes them particularly valuable for the production of alumina in the Bayer plant since silica is responsible for the loss of both alumina and soda chemically combined as XNa,OYSiO2,ZAl2O2. The ferric oxide, only traces of ferrous iron are present, offers no interference in the production of high grade alumina. Typical oxide analyses of three types of ore are given in Table I2 and a list of the elements occurring in spectrographic quantities in Table 11." The size of the individual particles in the ore makes successful petrographic examination extremely difficult. The ores contain some relatively coarse grains of heavy minerals such as ilmenite, magnetite, and rutile, but other than occasional crystals of a few microns, the greater portion of the minerals are submicroscopic in size and approach colloidal dimensions. The mineralogic composition of the ores has been investigated by X-ray and differential thermal analysis.' These investigations indicate that the predominant mineral phases present are gibbsite (A1203.3H2O), boehmite (Al2O3.H2O), hematite (Fe2O3), and goethite (Fe2O3-H2O). There is no evidence of the occurrence of diaspore (Al2O3.H2O) in either the Haiti or Jamaica ores, but some type of "amorphous" alumina may be present in some of the bauxites of Jamaica." The temperature stability regions in the alumina-water system have been investigated and are given in recent literature. In the temperature range where the hydrated forms are stable, as determined by hydrothermal bomb methods," ibbsite is the stable phase to 155°C (311°F), boehmite from 155°C (311°F) to 280°C (536oF), and diaspore from 280°C (536°F) to 450°C (842°F). Although quite similar in many characteristics, the Haiti and Jamaica ore show a divergence in mineralogic composition that is reflected in the extractability of the alumina described in later paragraphs. Two principal differences occur in mineralogic composition. The iron-bearing mineral in the Haiti ores is predominantly hematite, while in the Jamaica ores goethite is predominant.4 Directly related to the extraction of alumina are the two minerals, gibbsite and boehmite. Boehmite is relatively high in the Haiti ores and in some of the less soluble Jamaica ores, while gibbsite predominates in the ores in Jamaica amenable to the American Bayer process of extraction. Pedersen and Related Processes In general, all processes for the extraction of alumina involving sintering or fusion of bauxite ores with limestone, soda ash, or a combination of limestone and soda ash followed by leaching, are based on the formation of alumina compounds that. yield alumina soluble in the subsequent leach. The principal idealized reactions in respect to alumina and silica for the three types of processes are as follows: Soda Ash Sinter: A12O3 + Na2CO3 = Na2O-Al2O, + CO2 SiO2 + Na2CO3 = Na2O . SiO2 + CO2 A12O2 + SiO2 + Na2CO3 = Na2O.Al2O8. SiO2 + CO2 Leach (with excess water): H2O + Na2O-A12O3 = 2 NaOH + A12O3 (insolution) H2O + Na2O-SiO2 = 2 NaOH + SiO2 (in solution) Soda Ash— Limestone Sinter: Na2CO2 + A12O3 = Na2O.A1203 + CO2 2CaCO3 + SiO2 = 2CaO . SiO2 + 2CO2 Leach (with excess water): Na2O' A1208 + H2O = 2NaOH + A13O3 (in solution) These latter reactions are the basis of the sinter process currently used for the recovery of soda and

Jan 1, 1952

National Society of Professional Engineers has thrown its full sup- port behind pending legislation to appropriate $500 million for national conversion efforts that would provide employment opportunities for engineers, scientists, and technicians who are currently unemployed because of the decline in defense and aerospace programs. Known as the Davis-Giaimo bill, the proposed legislation would raise total Federal investment in science and technology to an adequate annual spending level and keep it proportionally equal to the growth in the GNP. If passed, the bill would increase and maintain Federal obligations for civilian-oriented research and development activities to a parity level with similar obligations for defense research development. U. S. Bureau of Mines has cataloged and placed on open file an inventory of U.S. coal deposits which can be economically strip mined at today's production costs. The costs include charges for reclaiming the mined land as required by 21 states. The report claims that some 46 billion tons of bituminous coal and lignite can be strip mined under present economic conditions, and that 32 billion tons of the total is classified as having less than 1% S. The report reviews strippable coal deposits by state, by county, by coal seam, by coal-seam thickness and by sulfur content. The report also gives an up-to-date summary of state laws on surface mine reclamation. Open-file copies of "Strippable Reserves of Bituminous Coal and Lignite in the U.S." may be consulted in Washington, D.C., at the Department of the Interior library and at U.S. Bureau of Mines offices in Pittsburgh, Denver, San Francisco. Dallas. Spokane, and Douglas Island, Juneau. Alaska.

Jan 1, 1971

By J. E. Hanafee, G. J. London

MANY studies of the deformation behavior of materials under a superimposed hydrostatic pressure have shown that materials brittle at ambient pressure behave in a ductile manner under pressure. Thus, with a metal such as beryllium which possesses relatively low ductility, but otherwise exhibits quite useful physical and mechanical properties, hydrostatic pressure may be particularly useful for both forming beryllium shapes and studying its deformation behavior. In fact, it has been found1"4 that polycrystal-line beryllium in both ingot and powder form appears to behave in a more ductile manner on a macroscopic level in a hydrostatic pressure environment, and it has been suggested2 that this is due to activating a new slip mode. Furthermore, Andrews and Radcliffe5 have found pressure induced nonbasal dislocation activity in hot pressed beryllium. Recently6 it has been shown in "c-axis" compression tests under hydro-static pressures up to 28 kbars that the shear stress needed to cause slip with a Burgers vector out of the basal plane (pyramidal slip) does not change with increasing pressure in beryllium with a purity of some 99.5 pct. This material is equivalent or more pure than the beryllium used in the previous pressure studies. Thus, it appears, as suggested by Inoue et al.,3 that the hydrostatic pressure affects the fracture stress rather than the stress necessary to activate pyramidal slip in beryllium. However, in "c-axis" pressure tests on high purity 12 zone pass beryllium (˜50 ppm total impurities) the macroscopic compression stress needed to cause pyramidal slip was considerably lower than that at ambient pressure.6 It has further been shown that alloying beryllium with nickel and copper in the range 2-5 wt pct also favors the occurrence of pyramidal slip in "c-axis" compression tests,7'8 while lower amounts of nickel and copper do not have significant effects. In the present study the combined effect of hydrostatic pressure and alloying high purity beryllium on the shear stress needed to cause pyramidal slip has been ascertained. A 2.5 wt pct Cu alloy was selected as the first alloy to study as this level of copper did favor pyramidal slip at room pressure. A high purity (12 zone pass) single crystal of beryllium 0.3 by 0.1 by 0.1 in. was cut and polished by an orientation and lapping technique8 so that the top and bottom compression surfaces were parallel and within 3 min of arc to the (0001) plane and the sides parallel to the {l010} and {ll20} planes. In these compression specimens, therefore, the resolved shear stress was nearly zero on both the basal and prism planes, and slip was restricted to pyramidal systems. Analysis of slip traces on the two lateral surfaces served to accurately identify the active slip planes.6'9 The pressure unit was a modified piston-cylinder device fitted with a manganin transducer coil arrangement which continuously monitored and recorded the hydro-static pressure. The load on the specimen was measured by a strain gage load cell which operated entirely within the pressure chamber. This load cell was calibrated before and after each pressure cycle at room pressure in situ and the calibration did not vary more than ±1 pet. These techniques and devices have been previously described in more detail.6 Successively higher compressive stresses were applied to the single crystal under a superimposed hydrostatic pressure until fracture occurred. The strain rate was (4.5 ± 2.0) x 10-6 sec-1 and the average rate of pressure application and release was approximately 0.3 kbars per min. As the load on the specimen was applied by the piston which was used to increase the hydrostatic pressure, the pressure increased during the compression test. This increase ranged from 0.0 to 0.8 kbars, and the maximum hydrostatic pressures are quoted in Fig. 1. The lateral surfaces of the specimen were examined in a light microscope after each pressurization/stress cycle so that the stress at the onset of {1122} pyramidal slip could be ascertained. Post compression height measurements allowed the plastic strain in the specimen to be evaluated to within 0.03 pct. The resulting compression stress-plastic strain curve is shown in Fig. 1 with results of a "c-axis" test on a similar Be-2.5 wt pct Cu single

Jan 1, 1970

By F. M. Stewart

A paper by Hurst and van Ever-dingen in 1949 led to the practical solution of many nonsteady-state flow problems.' Subsequently, applications of this material have been discussed by several authors. The purpose of this note is to outline a simplified direct procedure for water-influx pressure predictions for pressures above the bubble point. The prcposed procedure is unique in that after the "time-conversion factor" and the "influx constant" are obtained, predictions are made without trial and error. The elimination of trial and error is made possible by expressing certain PVT characteristics as explicit functions of pressure. The procedure is applicable to fields producing at pressures above the bubble point and under radial water drive from an infinite aquifer. In the usual applications it is required to predict (1) withdrawals given future pressure history or (2) reservoir pressure, given future withdrawals or production. The theory, assumptions and conditions under which the nonsteady-state solutions hold are covered in the references and are not repeated. The simplified direct procedure outlined here has been developed from published solutions for the so-called "pressure case". A similar direct procedure for the same special conditions has been developed for the "rate case"; however, in this instance the procedure is lengthy and offers no advantage over the trial-and-error solution. Consequently, this paper covers only the procedure based on the pressure case. DISCUSSION Under the pressure case prediction of withdrawals from a water-drive field, given the future pressure history, involves the use of a nonsteady-state water-influx term together with the material balance equation. The solution of a particular problem requires the following steps: (1) division of past pressure and production data into equal time intervals; (2) computation of cumulative water influx vs pressure drop for each time interval of past history using the material balance equation; (3) determination of the best values for the "time-conversion factor" and the "influx constant" by equating the nonsteady-state influx term with the influx computed in Step 2 (this requires a trial-and-error procedure); (4) prediction of influx for a given pressure drop using the influx term and the computed factors from Step 3; and (5) calculation of fluids produced using the predicted influx in the material balance equation. A forecast of the water-oil ratio or water production rate is required to complete the calculation. It is assumed that a reliable estimate of original oil in place is available, as well as the production and pressure history, and data on reservoir fluid characteristics. If the original oil in place is unknown, it may be computed simultaneously with the tinie-conversion influx factors2,3. However, the oil in place so computed may be considerably in error3; consequently, it is usually preferable to use oil in place estimated from pore-volume data unless there is considerable doubt as to its accuracy. The Material Balance Equation Above the Bubble Point Above the bubble point the simpli-

By W. N. Best

This paper is not intended as a scientific discussion of the combustion of oil but is written from the standpoint of an operator who has the experience and qualifications necessary to guide others in producing the most economical results in the use of liquid fuels. Oil, in this paper, usually means petroleum or its products but incidental reference is made to other liquid and gaseous fuels, so that the term may be considered as referring to all liquid and gaseous hydrocarbons in comparison with solid fuels, as coal and wood. However, only a few of the principal factors in the use of oil as a fuel can be given. The present, and prospective, high price of coal is causing users of fuel to renew inquiry as to the merits of other forms of fuel for industrial purposes. Crude oil (petroleum) is proving to be one of the world's most valuable mineral resources. The recent discovery that oil underlies a considerable area of the United States, Mexico, and other parts of the world to a greater extent than was formerly believed and the large production of some of the wells in these areas shows the probable quantity of fuel oil that may now be available. Through the energy of Lord Cowdrey, who was one of the pioneers of the oil industry in Mexico, oil has been discovered in England; some prominent geologists believe that it may be found in quantity in Great Britain. For years, oil has been known to be of great value in the manufneture of metals. It has proved incomparable in forge shops, steel foundries, heat-treating furnaces, and wherever accuracy of temperatures is essential, or where a maximum output is desired as well as quality of metal. In some types of equipment, the output produced with oil as fuel is double that obtained with coal and at a reduction of 50 per cent. in the cost of the fuel. For example, in drop-forging plants, the metal is always waiting for the man when oil is used as fuel, whereas with coal, the man must wait for the metal to become sufficiently heated. It has only been since January, 1919, that the oil supply could be relied on for boiler service, owing to the war conditions and the inability to get oil tankers for the delivery of the oil from Mexico to Atlantic ports; but now a constant supply is assured, and many manufacturers are installing it in their power plants. The cost varies with the size of the

Jan 1, 1921

By AIME AIME

As already announced in the January Bulletin, this publication will be issued during the coming year monthly instead of bi-monthly as heretofore. Among other reasons for this change, it is desired to effect thereby the earlier transmission to members of important papers, lists of candidates for membership, and other items of timely information. Spokane Meeting and Excursions. Further details of the' 97th meeting of the Institute have been sent to members in the Circular of May 8, 1909. For, convenience of the members a summary of the additional in¬formation is here presented. A special train of Pullman cars will leave Chicago about September 15. This train will be side-tracked at all places visited, and the sleepers will be available for lodging and the dining-car for meals during the entire trip, except during the Yellowstone Park tour. The general. cost of the trip per member will be $300, which includes transportation, berth, and meals for the entire trip from Chicago back to Chicago, almost 6,000 miles, and the tour through Yellowstone Park, occupying in all about 30 days. Special accommodations on the train will be furnished at the following, rates

May 1, 1909

By Alfred Weiss

Over the past 25 years hard-rock mining companies have developed a number of profitable computer applications which appear applicable to operations in the coal industry. The evolution of these applications are described and the most profitable discussed. The basic nature of these systems is that they must cut across organizational boundaries. While technological advances contributed significantly to the successful implementation of computers within mining, the human aspects related to organization, management and control of systems projects remain as key to future success in coal as they were and still are in hard-rock mining.

Jan 1, 1983

By F. D. Rosi, C. H. Mathews

THE plastic properties of face-centered cubic metals below room temperature present a field of investigation which has not been extensively ex-plored. The work by Schmid and Boas1 has demonstrated the importance of temperature upon such properties as strain hardening and critical resolved shear stress. The work by Yamaguchi2 upon the shear stress as related to the number of slip bands accentuates the necessity for further experiments of a similar nature. The approach to a mechanical equation of state from the standpoint of thermal fluctuations and activation energies by Becker3 and more recently by Kauzmann4 further emphasizes the need for a quantitative and more comprehensive analysis of the dependence of fundamental plastic properties on temperature. The purpose of the present work was to investigate specifically: (1) The gross shape of the stress-strain curves at several temperatures, (2) the change in the critical shear stress as a function of temperature, and (3) the number and appearance of slip bands as a function of strain and temperature. Preparation of Specimens Single-crystal specimens of 99.996+ pct alumi-num, 1/2 in. in diam and 5 to 6 in. in length, were made by the Bridgman method of gradual solidification from the liquid state. The crystallographic orientation of the single crystals was determined from back-reflection, Laue X-ray photograms ac-cording to the method described by Greninger.6 In most specimens the Laue photograms showed double diffraction spots indicative of the lineage structure type of imperfection, discussed in great detail by Buerger.7 The angular spread of these spots was never observed to exceed 2". Most of the crystals were radiographed to insure against microporosity. In preparing the metal surface for optical microscopy, the following sequence of operations gave good results: The as-cast crystals were turned down in a lathe, 0.001 in. per cut, to obtain a 2.5 in. gauge length. The cold-worked layer resulting from this operation was removed chemically by etching with Tucker's reagent. Then the specimen was polished mechanically through 2/0 metallographic emery paper, after which it was etched again to remove the cold-worked layer resulting from the mechanical treatment. A 48-hr anneal at 580°C ±10°C followed so as to insure an essentially stress-free single crystal. After the annealing treatment, the specimen was electrolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. With a current density of 10 amp per sq dm (decimeter) the time required to obtain a satisfactory surface varied from 10 to 12 min. The polish-ing was carried out for short periods of 2 min to avoid rapid deterioration of the solution as well as to enable the rotation of the specimen 180" for uniformity of polish. It was necessary to place the solution in a bath of dry ice in view of its explosive nature at room temperature. Etching of the electrolytically polished surface was accomplished by using the fuming etch-pit method recommended by Lacombe and Beaujard8 for high-purity aluminum. Method for Tensile Testing A modification of the loading equipment devised by Miller9 was used. In this apparatus, the specimen was suspended from a chain and gimbal arrangement (for axial loading) in a heavy steel framework connected at the bottom to a balanced 6:1 lever and bucket system. Loading of the specimen was accomplished by allowing sand to flow from a reservoir into the bucket suspended from the longer end of the lever-arm at a rate of approximately 3 lb per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire, strain gauge and an SR-4 portable strain indicator (type K), which permits a reading accuracy of 2 microinches per inch. For low-temperature study, the gauge was calibrated by measuring the elastic modulus of an annealed stainless steel rod, which is known to be independent of temperature."

Jan 1, 1951