Search Documents

By J. R. Dawson, A. B. Kinzel

THE purpose of testing is to determine whether the material in question is identical in all essential respects with similar material which has given satisfactory service. The most common method of securing such information is to select samples as representative of the entire material and subject them to destructive tests. As the welding industry grew, service data were accumulated and tests of welds took on new significance. New tests were devised and old tests modified so as to be more pertinent to welding. Moreover, in some cases the generally accepted procedure of testing by sampling is not accorded the same degree of confidence when applied to welds as in the usual applications. Thus, in instances where great hazard would be involved should the material fail, means of non-destructive testing have been sought with favorable results. Accordingly, tests used today may be divided into two groups, destructive and non-destructive tests.

Jan 1, 1930

By L. C. Brown, S. K. Behera

The diffusion rate in Ag-Sb couples is sensitive to con~pressive load with the width of Ag3Sb, the only phase present in the diffusion zone, increasing with stress up to 800 psi and remaining constant above this. Kirkendall marker experiments show silver to diffuse much faster than antimony in Ag3Sb and incipient porosity may therefore develop at the Ag/Ag3Sb interfnce restricting the transfer of atoms from the silver into the diflusion zone. Application of compressive stress reduces the tendency for porosity to develop and so increases the growth rate. In a recent paper Brown et al.1 observed a significant increase in the thickness of Cu2Te in Cu-Te diffusion couples on application of a compressive stress as low as 20 psi. Similar stress effects have also been observed in the Fe-A1,2 Al-u,3 arid cu-sb4,5 systems. It has been suggested that the increase in growth rates of intermetallic phases in these systems is due to a decrease in the amount of Kirkendall porosity with applied stress. In the present paper, results are presented of the effect of compressive stress on diffusion in Ag-Sb, together with a detailed examination of the Kirkendall effect. The Ag-Sb phase diagram6 shows that antimony has a moderate degree of solid solubility in silver, 5.7 at. pct at 350°C, but that there is essentially no solubility of silver in antimony. There are two intermediate phases— (hcp7) from 8.8 to 15.7 at. pct Sb and Ag3Sb (orthorhombic8) from 21.8 to 25.9 at. pct Sb. EXPERIMENTAL Diffusion couples were prepared from fine silver of 99.95 pct purity and from antimony of 99.7 pct purity. Both the silver and antimony were produced in the form of discs 1/2 in. in diam by approximately $ in. thick, with surfaces ground flat to 3/0 emery paper. Diffusion anneals were carried out in the apparatus previously described.1 A compressive load was applied to the diffusion couple through a lever arm system, with a reproducibility estimated to be ±10 psi. All runs were carried out in a protective hydrogen atmosphere. Following the diffusion anneal specimens were sectioned and polished and the width of the diffusion zone was measured metallographically. Composition profiles were measured using an electrostatically focused electron probe with a spot size of 10 , counting on Sb L radiation. Corrections for matrix absorptiori and fluorescent enhancement9 were not required. S. K. BEHERA, formerly Graducate Student, Department of Metallurgy, University of British Columbia, is now Postdoctoral Fellow, Whiteshell Nuclear Laboratories, Atomic Energy of Canada Ltd., Pinawa, Manitoba. L. C. BROWN, Junior Member AIME, is Associate Professor, Department of Metallurgy, University of British Columbia, Vancouver, B.C., Canada. Manuscript submitted June 14, 1968. IMD RESULTS Fig. 1 shows an electron probe traverse of a typical diffusion zone. In all couples examined only one intermediate phase was observed and the composition of this phase, 23 wt pct Sb, was in good agreement with the composition of Ag3Sb, 23 to 28 wt pct Sb. The presence of this phase was confirmed by X-ray diffraction of filings taken from the diffusion zone. The probe traverses showed no detectable solid solubility in either the silver or the antimony although the phase diagram indicates that some antimony, up to 6.5 wt pct pct Sb, should be in solid solution in the silver. However the width of this portion of the diffusion zone would be expected to be very small in view of the low diffusion coefficient in the silver, 4 x 10-l6 sq cm per sec at 350°C, 10 compared with that in the Ag,Sb, estimated as 3 x 10-8 sq cm per sec in the present work, and this region would therefore not be expected to be seen in the probe traverse. Application of stress resulted in a significant increase in the width of the diffusion zone, Fig. 2. At 350°C, the thickness of Ag3Sb increased from 250 at 0 psi to 400 p at the limiting stress of 800 psi, indicating an apparent 150 pct increase in the diffusion coefficient. Similar behavior was also observed at 400°C, indicating that the stress effect is not characteristic of just one temperature. The growth of Ag3Sb at 350°C and at various stresses is shown in Fig. 3. In every case the growth rate was parabolic indicating diffusion control. The kinetic curves all passed through the origin showing that delayed nucleation of Ag3Sb was not responsible for the stress effect and that it was a real growth effect. A series of tests were carried out in which diffusion was allowed to take place at a lower stress following an initial high stress diffusion anneal. Speci-

Jan 1, 1969

By J. B. Sellers, G. R. Haworth, F. W. Brackebusch, P. G. Zambas

Results of large-scale mining experimentation carried on in Stage II of the Anvil Points Oil Shale Research Program, Rifle, Colo., are reported. After a new adit was excavated, over 500,000 tons of oil shale was extracted during a 13-month period by a modified room and pillar method. Experiments in drilling and blasting headings, benches, and crosscuts are reported. Roof-bolting procedures, loading and hauling, and ventilation design are discussed. Results of the extensive investigations carried out by the cooperative industry group and earlier work by the U.S. Bureau of Mines indicate that mining oil shale is technologically feasible.

Jan 1, 1973

By R. M. Brick

SEGREGATION can occur only in cast alloys that solidify over a range of temperatures with a difference in composition of liquid and solid phases within this range (ignoring monotectic systems and chemical reactions as in rimming. steels). Thus a pure binary eutectic alloy should show no segregation unless undercooling occurs for one of the solid constituents of the eutectic; e.g., chill-cast Al-12 per cent Si alloys. The phasial condition implicitly described above-solidification over a range of temperatures with a compositional difference between solid. and liquid-is found in nearly all solid solutions or combinations of solid solutions and eutectics. Metastable conditions of solidification of these types of alloys cause coring; i.e., a difference in composition between the center of a dendrite and its periphery. This composition gradient can be detected usually only by microscopic examination of etched structures; it is a "micro" effect. The gradient of more immediate industrial concern is that between the center of a cast section and the surface layers. This gross (macro) effect is usually determinable only by sampling of the casting at different points, with chemical analyses of each sample. If the compositional difference is of the same type as in coring, the first parts to freeze being enriched in higher-melting-point constituents, and vice versa, the effect is called normal segregation. When what is apparently the first part of the casting to solidify shows a higher concentration of low-melting-point constituents, the effect is called inverse segregation. These macro effects are quite separate from the micro effect, coring, yet the latter must be. described first because it is an essential part of the picture. CORING Solid Solution, Ni-Cu The nickel-copper phase diagram is reproduced in Fig. Ia, in which the solid lines represent the equilibrium liquidus 1, 3, 7 and solidus 2, 5, 8, and where the vertical 1, 4, 8 represents a 55 per cent Cu alloy. Upon moderately rapid solidification, the first dendritic axes of composition 2 (see Fig. 1b) start to form at a temperature somewhat under I. Solidification continues by growth of the dendritic nuclei, but at temperature 4 the increment solidifying is of composition 5. The rapidity of this crystal growth prevents diffusion of nickel and copper atoms from adjusting the composition of the entire dendrite at 5, which it would be under equilibrium conditions. The average composition of a specific dendrite, or the entire solid phase, at temperature 4 might be that indicated

Jan 1, 1944

By Adrian C. Dorenfeld

Laboratory data form the basis for the design of flotation circuits. These data, obtained from testing samples of the ore, should show the optimum con- ditions for concentrating the ore and the effects of change in process vari- ables. Among the more important variables commonly met in flotation practice are: Liberation Size-This is the particle size at which substantially all of the valuable minerals are detached from the gangue minerals. Reagent Additions- Experimental data will show the reagents used and their quantity, quality, and point of addition. Pulp Density-This is an important variable in the design of the flotation circuit because it is one of the factors determining the size and number of flotation cells. Flotation Time-The time necessary to make the separation into concentrate and tailing depends on such factors as particle size and reagents used and must be known for determination of the size and number of flotation cells in the plant. Temperature of Pulp-Temperature affects flotation reactions. Water at approximately room temperature is satisfactory for most flotation separations, but some minerals such as fluorspar are best floated in hot water. Type of Circuit-Many types of circuits can be designed, as discussed in detail later. The laboratory tests should provide data for design of the plant circuit best suited to the ore. Water-Knowledge of the quality of the future plant's raw water is important because water quality may drastically affect flotation results. If possible, flotation tests should be made using samples of the water to be used in the plant. Flotation results may vary with seasonal temperatures and with circulation of reclaimed water. Experimentation can show whether it will be necessary to provide for heating, cooling, treating, or reclaiming the water. Uniformity of Ore-The extent of variation of the ore in hardness, grind- ability, mineral content, and floatability should be investigated so that the designer can ascertain methods to overcome problems caused by ore variations. Settling and Filtration Data-To design the plant flotation circuits, settling and filtration rates and ultimate percentage solids of the various products must be determined. Corrosion and Erosion-Corrosion and erosion tests should be made on the flotation pulps, particularly if the pulps are acid or at an elevated temperature, so that suitable materials of construction can then be chosen.

Jan 1, 1962

By Norman P. Goss

It is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.l-8 The broadening of the Ka lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the diffraction lines are broadened and the Ka doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolution of the doublet is lost when a metal is cold-worked and the Laue spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attributed the hardening to fragmentation of the grains into smaller units. Jeffries and Archer,ll after carefully considering the problem of work-hardening from many angles, came to the conclusion that cold-working mechanically refines the grains into smaller crystal fragments, some of which at least differ in orientation from the parent grain. The increase in

Jan 1, 1940

By Norman P. Goss

It is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.l-8 The broadening of the Ka lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the diffraction lines are broadened and the Ka doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolution of the doublet is lost when a metal is cold-worked and the Laue spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attributed the hardening to fragmentation of the grains into smaller units. Jeffries and Archer,ll after carefully considering the problem of work-hardening from many angles, came to the conclusion that cold-working mechanically refines the grains into smaller crystal fragments, some of which at least differ in orientation from the parent grain. The increase in

Jan 1, 1940

By Davis Baker

The direct-metal cars or ladles of the Maryland Steel Company have a capacity of 18 tons when filled within 12 inches of the top. On account of this large capacity, the formation of skulls in these ladles is by no means as rapid as in smaller ladles; but a skull once formed is a very unwieldy piece of metal to handle, and especially to remove from the ladle. We have found it cheaper to clean ladles often rather than make very heavy skulls. We aim to keep the ring of chilled metal that forms on the surface of the iron chipped off, so that the skull shall form principally at the bottom until it becomes so thick as to render the ladle unfit for service. Sometimes it happens that a ladle may be held for several hours filled with molten metal. This invariably leaves a large amount of chilled metal in the ladle. Frequently the skull will weigh several tons, and will be of the full size of the ladle inside, with a top crust, having perhaps a hole 12 inches square, through which the molten metal was poured. In order to remove skulls that cannot be easily chipped out with a bar, we use what may be called a skull-extractor, consisting of a hydraulic cylinder mounted in the center of a heavy cast-iron plate, standing vertically on a suitable foundation. Figs. 1 and 2 show the construction and operation of this apparatus, Fig. 1 being a view of the extractor with pistons extended to full stroke, and Fig. 2 a view with ladle in position and pistons about to commence the stroke. in both figures, A is the hydraulic cylinder, B the vertical cast-iron plate, and C the foundation. The water-pressure, admitted through the pipe, P, is 750 pounds per square inch, and the inside diameter of A is 14 inches. There are two pistons: D, fitting the bore of the cylinder, and E, 84 inches in diameter, moving inside of D. Both pistons move together when

Jan 1, 1893

By AIME AIME

THE autumn is the time that nearly all the special groups within the broad field of the Institute's activitives chose for their own special meetings. The big annual meeting in New York in February has its own special advantages, but to realize them involves sacrificing others. A meeting of a smaller group with the subjects brought up for discussion much more closely limited to a single field of interest has some advantages that a big general meeting cannot possibly have. And so the custom has gradually developed of having these smaller meetings in the autumn, at con¬venient places, so the men will not have to travel too far from the job to be present. Sometimes the meetings have for their field of interest a single phase of mineral technology, and are called divisional, and at other times they cover a diversity of topics that are locally important in that geographical area, and are then called regional meetings. Of the five meetings to be held this fall, four are divisional and one regional. Two of the divisional meetings are to be held in the same place at the same time, but with programs so arranged that they do not conflict.

Jan 1, 1930

By Reginald Williams

THE amount or value of the precious metals consumed in dentistry is probably amazing to most people. It falls very little short of that which is consumed in jewelry. Inasmuch as the ultimate destination is in the human mouth, dental alloys enjoy some importance because life and health depend upon restorations made with them. Prosthetic dentistry has made wonderful progress in the last few years. The manufacturers who supply the metals also deserve commendation. This industry which deals with metals to go-into people's mouths is comparatively new. There is no literature on the subject, and little or no precedent by which to be guided. It was only by close cooperation with the dentist or prosthetic technician that desirable physical properties were produced, as-nearly as possible, in the metals which were available and permissible. It is true that there were and still are conflicting opinions among the dentists as to the physical properties they require. Sometimes they request the impossible, such as alloys which are exceedingly stiff and springy, yet will bend or adjust easily. Even in this latter instance, progress has been made by supplying methods of heat-treatment whereby metals may be softened or hardened at will. (Figs. 1 and 2.) The demands made upon manufacturers are extremely varied. They must supply metals of tensile strengths ranging from approximately 30,000 to 100,000 lb. per sq. in. and over. The latter metals must be workable and in many instances capable of extreme deformation. They must not be affected by mouth conditions, nor should they oxidize greatly when molten, at red heat, or during a soldering operation. In addition to physical, specifications, color demands must also be met. The firm of which I have the most, knowledge manufacturers 11,553 standard stock articles of precious metals, taking into consideration formulas, finenesses, grades, colors, gages, lengths, sizes and weights. If special demands are taken into consideration, the number would be in excess of 25,000. Wrought metals are manufactured in a great many alloys of different sizes and shapes, such as plate, bar, rod, wire, sheet, strip, mesh and foil. There are also other products of importance.

Jan 1, 1928

By Willis H. Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep in Johannesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104º at sea level, insured reasonable safety, since all parts of the machine operated at subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By K. N. Weaver

In the early 1950's the cement industry began putting a new emphasis on geology. This article points up some of the industry's raw materials problems that geologists are uniquely qualified to handle. Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War 11, however, the industry began to recognize the need for geological exploration and some of the larger companies began to build a permanent geological staff. This development has its roots in: 1) The rapid expansion of the industry. After World War II and continuing into the early 1950's the demand for cement far exceeded the production capacity. This placed a great deal of pressure on the producers to enlarge capacity at their plants and to develop new sites. 2) The closing of many cement plants due to inadequate raw materials. Producers feared lack of raw materials due to inadequate exploration and evaluation. 3) An ever increasing pressure for upgrading of the quality of portland cement, necessitated upgrading the quality of raw materials. 4) The increasingly large capital investment needed to build new cement plants required a higher degree of accuracy in reserve calculation. These reasons are more or less self explanatory and will not be elaborated on. They are outlined to illustrate the probable evolution of thought among cement management to justify the development of a geological staff. In the author's personal experience the geologist must continually readjust to changing conditions within the industry. For example, cement production capacity grew so rapidly that today production is only about 70% to 75% of rated capacity (73.8% in 1963). Therefore, whereas the geologist's function during the active expansion of capacity was primarily one of exploration, one of his major functions today is the development of existing reserves. This assumes of course that reserves at existing plants have been proven to be adequate in terms of the company's reserve policy. Through the proper development of raw materials, the geologist can markedly influence quality control, production and long range planning. Examples of several of the operations of Medusa Portland Cement Co. will illustrate how proper attention to geologic detail pays off in the above areas. Because limestone is the major raw material of port-land cement, the examples will be concerned with it. DEVELOPMENT OF GEOLOGIC DETAIL One of the prime objectives of an exploration or development project should be the establishment of the stratigraphy and structure of the deposit. The basic tool for exploration and development is still the core drill, and the geologist must gain a maximum amount of information from a minimum amount of drilling. In order to obtain this objective the following is essential: 1) Adequate detailed geologic logging of cores. The core is first logged and separated into lithologically distinct units. In order to make the lithologic breaks as meaningful as possible, representative pieces of core (not all) are etched in dilute HCI. This removes the "drill polish", brings out the structure of the rock and indicates the proportion of dolomite and argillaceous material because dolomite and argillaceous material etch in relief. In this way the lithologic breaks become clearer and one gains a general idea of the chemical makeup before analysis. This method of logging lessens the probability of including two types of stone, e.g. limestone and dolomite into the same sample for chemical analysis. 2) Representative sampling for chemical analysis. After logging, the lithologic units are sampled for chemical analysis. A representative analysis can be obtained by extracting a 1-in. sample for every foot of core. For example, a lithologic interval of 10 ft to 20 ft would yield ten 1-in. samples taken at 11 ft, 12 ft, 13 ft... and 20 ft. These samples are then crushed, pulverized and split into a sample for chemical analysis. This sampling method represents a significant saving of time over splitting the entire core. 3) Preparing the core as a record. Because of the expense of storage and the difficulty of handling large amounts of core, only representative samples of each lithologic unit are saved for reference. An

Jan 1, 1965

By R. V. Colligan

[CONTENTS PACE Educating and Training Economic Geologists of the Future. By C. H. BEHRE, JR. (TP 2278, Min. Tech., Nov. 1948. Discussions by R. V. COLLIGAN and EVAN JUST) ....... I Mercury Industry in Italy. By EDWIN B. ECKEL. (TP 2292, Min. Tech., Jan. 1948. Discussion .............................. by C. N. SCHUETTE) 3 Chert in the Kingsport Formation at Mascot, Tennessee. By ARTHUR T. ALLEN. (TP 2299, ............... Min. Tech., Jan. 1948. Discussion by M. M. BUTLER) 5 Wall Rock Alteration at Butte, Montana. By RENO H. SALES and CHARLES MEYER. (TP 2400, Min. Tech., May 1948. Djscussions by C. D. HULIN, W. D. JOHNSTON, JR., and L. C. ................................... GRATON) 5] Educating and Training Economic Geologists of the Future R. V. COLLIGAN*-I can best illustrate my opinions by drafting another five year plan (Table 2). This plan is set up following the same stipulations outlined by Dr. Behre, namely: (I) the student is preparing himself for commercial work as a mining geologist; (2) he is attending an institution with a sufficiently broad curriculum (that is, engineering school and mining school as well as liberal arts college) to furnish the courses listed; and (3) he is not planning to continue his studies through to a doctor's degree before going into commercial work. A comparison of my study plan (Table 2) and that submitted by Dr. Behre (Table I) will at once point up the basic similarity, due to the obvious fact that there are so many essential courses which must be included in any outline of study. However, a more detailed analysis will show up certain differences, which, in fact, are only certain refinements on Dr. Behre's program. These I plan to discuss in order of their importance. The first and most important change is the addition of 12 hr of optional subjects, making a total of 24 hr of optional subjects as against a total of 12 hr under Dr. Behre's schedule. This of course entails the elimination of certain courses, which I shall discuss later. However, I wish to make it clear that I suggest eliminating these courses not because I feel that they are unnecessary, but rather because I feel the optional courses are more necessary to the complete education of the individual. I appreciate that Dr. Behre recognizes the importance of the cultural side of education, but I take issue with his thesis that the student will get it without credit and in his spare time. I do not think that the average college student, and certainly not the college freshman, is mature enough to know what he needs and where to get it in his spare time. I think it must be "spoon-fed"; he must be oriented through specific courses. University life (or should I say "college life") is too full of athletics, fraternity activities, dances, "bull sessions," and countless other enjoyable distractions, all of which contribute to the "full man." I fail to see how the average young American male can possibly sandwich in a necessary complement of "cultural activities" in his spare time. Since these latter activities do not fall within the pattern set by the "group," and show less promise of immediate return in enjoyment, or increased social status on the campus, they are bound to suffer in competition with the more popular, "group" activities. No doubt much of the criticism levelled against arts colleges, namely, that the cultural courses are useless, is well taken, for the culture

Jan 1, 1947

By Paul A. Farrar, Sanford Adler

The Tz-Zr system was reinvestigated using both metallographic and X-ray diffraction techniques. It mas found that titanium and zirconium are soluble in all proportions in both the a and 0 phases. The minimum in the transformation was found at 50 at. pct and 535°C. THE Ti-Zr system has previously been the subject of several investigations.1-6 A study by Hayes et al.5 using magnesium-reduced titanium and zirconium melted in graphite crucibles indicated that the system was a continuous series of solid solutions in both a and 0 phases with a minimum at approximately 545°C and 65 pct* Zr. These conclusions were substantiated by the work of Duwez4 as well as by the limited data of Craighead et al.,3 Fast,2 and deBoer.1 However, a more recent investigation of the titanium-rich region by Ence and Margolin6 indicated that the solubility of zirconium in a, titanium at 500°C is approximately 22 pct with the a + 0 field extending to approximately 47 pct Zr. Therefore in order to resolve this discrepancy the following investigation was initiated. EXPERIMENTAL PROCEDURES The alloys used in this investigation were prepared as 20- to 30-g buttons by nonconsumable electrode melting in a helium atmosphere. The starting materials were Bureau of Mines titanium BHN 71 and Foot Mineral iodide crystal bar zirconium. The titanium was premelted before the alloys were prepared to avoid excessive weight losses in the final melting. The compositions of the alloys prepared were as follows: Ti-12.0, 22.2, 29.0, 39.6, 50.0, 58.0, 72.4, 83.5. and 90.8 pct Zr. Prior to heat treatment the alloys were cold-worked 10 to 20 pct, stopping at the first signs of cracking. Specimens for heat treatment were wrapped in molybdenum sheet and annealed in argon-filled quartz capsules for the following times and temperatures: 750°C-40 days, 675°C-61 days, 600°C—109 days, 575°C-112 days, 550°C-112 days, 525°C—127 days, and 450°C —153 days. Quenching was accomplished by breaking the capsules in an iced-brine solution. The standard techniques used for polishing the specimens involved belt grinding, grinding on emery paper, polishing electrolytically, and etching with Remington "A" etch7 or "R" etch 8 Debye-Scherrer X-ray powder photograms were obtained for a number of samples using a 114.6-mm camera and CuK, radiation. Exposure times were from 19 to 23 hr. The powder samples were obtained by filing to 270 mesh size. After filing the samples were wrapped in molybdenum foil capsuled in quartz and reannealed at the temperature of original heat treatments; following the heat treatment the samples were quenched into iced brine without breaking the capsules. RESULTS AND CONCLUSIONS On the basis of the microstructural examinations of the heat-treated samples and of the X-ray diffraction data, the Ti-Zr system shown in Fig. 1 was constructed. The data indicate that a, and 0 titanium form a complete series of solid solutions with a, and ß zirconium. The minimum was found to occur at 65 pct (50 at. pct) Zr and 535°C, in excellent agreement with the earlier investigations,1-5 see Fig. 2. Typical microstructures are shown in Figs. 3 to 7. Figs. 3, 4, and 5 show the 22.2, 39.6, and 50.0 pct Zr alloys after heat treatment at 675°C for 61 days with the 22.2 pct Zr showing equiaxed a, and the 39.6 pct Zr alloy a + transformed ß, while the 50 pct Zr alloy shows only transformed B. Figs. 6 and 7 show the 29.0 and 39.6 pct Zr alloys after heat treatment for 109 days at 600°C. The 29 pct Zr alloy has an equiaxed a structure while the 39.6 pct alloy has a partially recrystallized a+ß structure. X-ray diffraction data obtained from the 50 pct Zr alloys after heat treatment at 525° and 450°C as well as from the as-cold-rolled material showed only those lineos which couid be indexed a: a titanium, good agreement with the previously published values. 2,4,5,9 Chemical analysis* of the 50 pct Zr alloy

Jan 1, 1967

By Saluja, Sunder S.

Man had to learn to break rocks as early as the Stone Age, when they formed his main source of raw material. He started with chipping and over the years has reached a stage where he can employ atomic blasts and break, with one blast, millions of tons of rock. In between these two extremes there have been several stages of development including fire setting, use of the expansion of water on freezing in chipped cracks in cold climates, the use of low or deflagrating explosive black powder in about the 17th century, the use of high explosives with the discovery of nitroglycerine in 1846 by Sobrero, followed by the monumental discoveries of the great Swedish scientist Alfred Nobel in the latter half of the nineteenth century.

Jan 1, 1968

By Robert Linton

IN 1898, Joseph L. Giroux and J. A. Snedaker organized the Pilot Knob Copper Co. and began developing the Pilot Knob mine at Kimberly, Nev., for high-grade copper ores, carrying good gold and silver values that the formation had disclosed. At that time the nearest railroad was over 150 mi. distant. The high-grade ores did not prove to be extensive at this point-at least to the depth. (240 ft.) to which the work was carried-but development of neighboring claims indicated extensive deposits of sulfide porphyry ore of concentrating grade lying at shallow depth, and deeper deposits of direct-smelting oxidized ores occurring in limestone near the limestone-porphyry contact. The properties passed through the hands of several organizations, with only meager development, until acquired in 1913 by Consolidated Coppermines Co., whose holdings now comprise 3480 acres of mining claims in the Robinson district. Since that time development has been prosecuted more actively; and for the purpose of determining the most efficient and economical method of treating the ores, considerable testing work has been done during the past three years, both in the laboratory and in actual mill operations. At first, the shipments were of ore high enough in grade to be profitable even with the long wagon hauls to the railroad and prevailing freight and smelting charges. In 1905, a blast furnace and a concentrator were erected at Kimberly. On account of insufficient ore supply, the blast furnace was never blown in and later was dismantled. The concentrator as originally equipped wag operated for only about two months, both because the ore supply was not sufficient and because gravity concentration did not yield satisfactory extraction. The location and arrangement of the mill further entailed high operating costs. In 1908, the Nevada Consolidated Copper Co. began to mill successfully, on a large scale, its sulfide porphyry ores, which are similar in character to the adjacent Coppermines ores. After that time, all of the ores and concentrates produced by Coppermines Company were

Jan 8, 1920

By O. N. Carlson, W. M. Paulson

A phase diagram is proposed for the Y-C system based on the vesults of thermal analyses, microscopic obsevvations, and X-ray diffraction studies. Three intermediate phases occur in the system: a congru-ently melting fcc phase with a wide range of homogeneity about the composition Y2C, an intermediate solid-solution region between 55 and 58 at. pct C, and a bct dicarbide melting congruently at 2415°C. All three compounds undergo a phase transformation at elezlated temperatures. A continuous serzes of solzd solutions exists between the fcc phase and the high-temperature form of YC2 with a maximum in the solidus at 2000°C and 30 at. pct C and a minimum at 1805°C and 54 at. pct C. THIS investigation of the Y-C system was undertaken as part of a nuclear materials development program. Yttrium-base alloys are of interest as possible containers for liquid metals, and carbides are currently receiving increased attention as high-temperature materials for advanced reactors and other applications. Previous work on this system was limited in scope, and the results were somewhat inconclusive and at times contradictory. Spedding et al.&apos; reported the existence of a triyttrium carbide having an fcc structure with a wide range of homogeneity and Dean et a1.2 reported the existence of a rhombohedra1 phase having the stoichiometry of Y2C. Bachella et a1.3 observed that the latter was the result of ordering of carbon atoms in the fcc solid solution. The ordering range was placed at 800" to 1000°C. Vickery et a1.4 reported a high-melting compound which they identified as yttrium dicarbide, and Spedding and coworkers1 determined the structure of this phase as bct with lattice parameters a = 3.66 and c = 6.17A. Samsonov et al.5 reported the melting point of YC2 as 2300" * 50°C. Recently Bowman et a1.6 found a transformation in the dicarbide from the tetragonal to an fcc form at 1320 20°C. Samsonov and coworkers7 reported a monocarbide of yttrium melting at 1950" * 20°C and also a sesqui-carbide melting at 1800" * 50°C. The existence of the latter has also been indicated by others,1&apos;8 but neither compound has been definitely established. The Y-C phase diagram shown in Fig. 1 was proposed by Chubb and Keller8 in 1964 based on the data available at that time. The tentative nature of this diagram together with the uncertain status of the compounds indicated that additional work on this system was needed. EXPERIMENTAL PROCEDURE Yttrium metal of 99.9 pct purity was prepared for use in this study by the reduction of YCl, with calcium to form a sponge product.9 The major impurities in this material were as follows: 100 ppm C, 150 pprn H, 20 ppm N, 300 to 1000 ppm O, <20 ppm Ca, <100 ppm Cr, <80 ppm Cu, 150 ppm Fe, <30 pprn Mg, <400 ppm Ta, and <100 ppm Ti. Alloys were prepared by arc melting yttrium sponge together with pieces of high-purity graphite rod in a purified argon atmosphere. Homogeneity was insured by repeated melting, inverting the ingot between melts.

Jan 1, 1969

By T. Egleston

circumstances, would prefer the steel with which they are now familiar, to a specimen that Mr. Sandberg has described as having broken into seventeen pieces under the wheels. After blowing such low manganese steel, it may be coaxed into a rail, but it is a wonder that it holds together so long as it does, with so great a nornber of minute flaws. I would not in any way depreciate chemistry, but I think it should be kept in its proper sphere. Let the chemist look after the quality of pig metal, and apply common sense in the avoiding of extremes, then the most fastidious railroad cannot find fault with the result. PROFESSOR EGLESTON, New YORK City : It is not my place as an engineer to apologize for the chemists, but as no one seems disposed to do so, and as they have had more than their share of criticism, 1 am glad to say that I believe there are chemists in this Institute whose work and word are just as reliable, arid perhaps even more so, than that of the average engineer. But we ought to make a distinction; there are chemists and chemists. With the ordinary commercial chemist, who looks upon the science as so much merohandise, I have not a particle of sympathy; but with the chemist who looks upon his profession as engineers do upon theirs, I have every sympathy. When matiufactorers and engineers go to a chemist and ask him to make an investigation, and scretv him dowu to the lowest point, turning the equivalent of his brains into cents and mills, they ustially get an exact equivalent in poor work for miserable pay, and no one has or should have any sympathy with them, and the under these conditions has no right to ask for any, and no reason to criticise any work that he may get under such circumstances. But I am disposed to think that the chemists who have been replwented and discussed at this meeting do their work conscientiously, and that it is as reliable as that of almost any profession. I believe, however, that this problem of steel rails is being investigated in a wrong direction. I said so at the Pittsburgh meeting, and I think the discussion of this meeting will prove it to all those who have heard it. I think the chemigt is incapable of solving this problem unlees he goes very far into the domain of physical chemistry, so far that it becomes physics and not chemistry; and that the physicist will be the one on whom we must rely in the future for the elucidation of the subject. The chemist may aid the physicist, but it is my decided opinion that we are looking in the wrong place to get the explanation of the phenomena.

Jan 1, 1881

By Harold Vance

EMPLOYERS of engineers have not always been satisfied with the training that young graduates have received in the conventional four-year course. Specifically, employers of petroleum engineers for a number of years have believed that a four-year course does not allow sufficient time for the student to secure a fundamental engineering background plus the fundamentals of petroleum engineering. A group of California employers went so far as to set up a type of curriculum for a petroleum-engineering course, which was based on four years of undergraduate work and one year of graduate work, with most of the petroleum-engineering courses included in the graduate year.

Jan 1, 1944

By John S. Crout

TWENTY-FIVE years ago the training of an engineer was of interest solely to the educator and to the student entering the field. At that time the engineer&apos;s position in society was relatively simple. His training emphasized design and operation and he expected to enter industry to handle the engineering problems of raw materials production, mechanical and product design, and the operation of power plants, factories, transportation and communication systems, and similar phases of industrial activity. He was not concerned with or particularly interested in the problems of management, administration, sales, publicity, industrial relations, or of legislation. To a large degree he was content to leave these matters to self-made businessmen, or men trained in law, finance, or commerce. That period in the evolution of the engineer is now history. It is generally conceded that the modern world is dependent upon engineering technology for its day-to-day survival. The continued operation of facilities on which mankind relies is dependent upon the functioning of mines, utilities, chemical plants, and other factories, all of which require the knowledge and the skills of trained engineers. Thus from a purely mechanical point of view, the engineer has become indispensable to

Jan 1, 1947