Search Documents

By Utley Wedge

(Cleveland :Meeting, October, 1012.) In general, the art of securing copper from sulphide ores or concentrates may be said to consist of : (1) separation, in the molten state, of copper sulphide with some iron sulphide, from the great bulk of gangue-material, followed by (2) elimination of sulphur and iron from the molten matte, by oxidation and fluxing, leaving metallic copper. The definition is made broad enough to cover the general practice, whether or not the ore or concentrate is given a preliminary roast for the removal of surplus sulphur. The above process, which I will designate as the smelting process, makes necessary the presence in the ore, or the addition thereto, of such silica, lime, and iron as may be necessary for the formation of a light and fusible slag, together with sufficient sulphur and iron for the formation of copper-matte, and also the addition to the matte of sufficient silica for the oxidation and fluxing-out of the iron. These items, together with the cost of fuel sufficient for melting the mass, constitute important items of cost in the copper-smelting process. Numerous cases where fluxing-materials are scarce or dear, or where fuel is expensive, have caused special attention to be given recently to the wet process of copper-extraction, which may be designated as consisting of forming soluble copper salts which are then washed or leached out of the ore or concentrates by dissolving in water or acid. Metallic copper may then be secured from the solution of copper salts by electrolysis; by cementation; or copper can be brought out of the solution as a * Presented also at the Joint Meeting of the Institute and Section IIIa, Metallurgy and Mining, of the Eighth International Congress or Applied Chemistry, New York, N. Y., September, 1912, and here published by mutual agreement.

Dec 1, 1912

By Reed W. Hyde

SOME information has been published on the sulphur dioxide concentration of gases from Dwight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide flotation concentrates mixed with minus 20-mesh oxide ore, the mixture carrying 16.8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO2 might be utilized, a series of runs was made to determine the concentration of S02 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1) 2 to 1 1/3 in., (2) 4 to 3 1/2 in. and (3) 6 to 5 1/8 in. The averages of the determinations from each series are platted on the graph (Fig. I). The vertical scale shows the percentage by volume of SO2 (as determined by the Reich method), and the horizontal scale shows the time expressed as percentage of the total sintering time. Sintering was considered to be complete when no S02 could be detected in the gases. In all cases the depth of bed was 4 ½ in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which S02 determinations were made could not be measured, but has been calculated from the S02 content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume will usually drop slightly toward the middle of the period and increase toward the end. However, this assumption is a reasonable approximation. Several interesting features are brought out by these data. In general, the published data on S02 concentration in sintering under ordinary conditions show a high S02 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SO2 in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum S02 concentration is obtained 2 ½ min. after

Jan 1, 1942

By Russell G. Wayland

This paper gives the author's personal idea of the general viewpoint of the world's largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. Muscovite Mica Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. The Mica Problem Block muscovite mica is commercially classified into the following general qualitie3, beginning with the best quality: 1. Clear and Slightly Stained (C & SS). 2. Fair stained (FS). 3. Good stained (GS). 4. stained (s). 5. Heavy Stained (HS). 6. Black spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately 1 C & SS to 4 FS to ro GS to 14 S to whatever the

Jan 1, 1948

By Russell G. Wayland

This paper gives the author's personal idea of the general viewpoint of the world's largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. Muscovite Mica Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. The Mica Problem Block muscovite mica is commercially classified into the following general qualitie3, beginning with the best quality: 1. Clear and Slightly Stained (C & SS). 2. Fair stained (FS). 3. Good stained (GS). 4. stained (s). 5. Heavy Stained (HS). 6. Black spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately 1 C & SS to 4 FS to ro GS to 14 S to whatever the

Jan 1, 1948

By D. S. Sanders

IN the four mills of the Cerro de Pasco Copper Corp. in Peru, some 3000 tons of complex sulphide ores are treated daily, with four kinds of concentrates produced: copper, lead, zinc, and pyrite, each containing values in silver, gold, bismuth, and some other metals. Copper occurs in the various ores as chalcopyrite, enargite, tetrahedrite, tenantite, bournonite, and chalcocite; lead as galena; and zinc as sphalerite and marmatite. Small amounts of silver and tungsten minerals are also present. The gangue consist mainly of shale, quartzite, calcite, rhodochrosite, pyrite, and pyrrhotite. In general the values are freed with a relatively coarse grind, about 70 prr cent minus 200 mesh being the finest to which the pulps are ground. In Morococha and Casapalca however. sphalerite particles much finer than this contain inclusions of chalcopyrit r. At Cerro de Pasco the silver and gold are present in all sizes of the ground pyrite.

Jan 1, 1945

By D. D. Pollock

Many constitution diagrams do not indicate the limits oJ solid solubility of the silver-rich solid solutions below 200°C. Thermoelectric measurements were employed to determine this limit in the nieighborhood of room temperature. The appearance of a second phase causes a discontinuity to occur in the tkevtrroelectric power as a function of cornposition at constant temperature and pressure. This discontinuity was employed to determine the limits of the silver-rich terzinal solid solutions of the Ag-A l, Ag-As, Ag- Bi, Ag--Ge, Ag-In, Ag-Pb, Ag-Sb, and Ag-Sn systenls at 30°C. CONSIDERABLE work has been done on the constitution of binary alloys of silver. The available data have been compiled by Hansen1 and Elliott.2 However, many of the binary diagrams do not show the limits of solid solubility of the silver-rich solutions below about 200° C. This work was undertaken in an attempt to extend these limits to the neighborhood of room temperature . PREPARATION OF ALLOYS All of the alloys were made with silver containing less than 0.014 pct (by weight) of impurities. The materials were weighed out into 225-g heats and melted in a high-frequency induction furnace. The indium, tin, and antimony alloys were melted in A1203 crucibles, under a boric anhydride cover, and were poured into split graphite finger molds. The aluminum, germanium, arsenic, lead, and bismuth alloys were melted in machined graphite crucibles; they were also covered with boric anhydride and poured into split graphite finger molds. The $-in.-diam ingots were heated to 750°C and were forged and hot-rolled down to 0.1 by 0.1 in. The wires were pickled in a 25 pct HNO3-75 pct H2O solution to remove any oxygen-rich surfaces. The wires were then annealed at 550°C for 2 hr in a dissociated ammonia atmosphere. They were then furnace-cooled for 20 hr to room temperature in this atmosphere. The wires were cold-drawn to 0.0808 in. diam. The finished wires were again annealed at 550°C in the same manner as in the first anneal. Thermoelectric Power. The thermoelectric power of a single specimen of each alloy was determined against pure silver which contained a maximum impurity content of 0.014 pct by weight. The wire specimens were straightened and then cleaned with ethyl alcohol. They were then reannealed in the same way as the finished wires to assure that any residual stress would be at a minimum level. Previous work has shown that the presence of small amounts of stress has the effect of decreasing the thermoelectric power. The alloy specimen was soldered to the pure silver wire to form the measuring junction. A standard set of copper leads was then soldered to the reference junctions of the thermocouple. These junctions were maintained in separate dewar flasks which contained finely shaved melting ice during the test. The thermal electromotive forces of the thermocouples were measured at four temperatures between 15° and 45°C. A known source of electromotive force was balanced against the output of the thermocouple until a null balance was reached. The data were then expressed in terms of the thermoelectric power at 30°C. The results were then converted to absolute thermoelectric power, s303.3 These data have an average error of less than ±0.2 pct. RESULTS AND DISCUSSION All of the experimental data are given in Table 11. Since the electromotive forces of the binary alloys of silver were determined against the pure silver from which they were made, the resultant thermoelectric powers are only a function of the intentionally added binary elements at the constant test temperatures. This provides a direct measure of the effects of the alloying elements. The absolute thermoelectric power of an alloy of silver is given4 by:

Jan 1, 1968

By R. H. Frazier, C. H. Lorig, F. W. Boulger

THERE are both advantages and disadvantages in using semikilled steels in place of killed steels. One advantage of semikilled steels is they provide a higher ingot-to-product yield. This is especially important to shipbuilders in the time of national emergency. By using semikilled steel for hull plates, a greater number of ships can be built from the same ingot tonnage. Consequently, if semikilled steel plates are adequate for the service, the advantage of the higher product yield is of considerable importance. The performance of hull plates is closely associated with the ductile-to-brittle transition temperature, and this, in turn, is strongly dependent on the composition of the steel. A low transition temperature is desirable because it indicates that the steel is less likely to fail at low ambient temperatures. Killed steels are known to have lower transition temperatures than semikilled steels. It is believed that the better qualities of killed steels in this respect are due mainly to the low oxygen contents of the steel. The principal deoxidizers, aluminum, silicon, and manganese, lower the oxygen content. Fundamental studies1-0 have shown that the oxygen content remaining after the addition of one of these three elements is influenced by the residual amounts of the other two present. In the current study, therefore, various amounts of silicon and aluminum were added to steels containing different manganese contents for the purpose of studying the influence of silicon and aluminum on the notched-bar properties of hot-rolled steels. Eleven types of steels were studied. The temperature at which the plates were finish-rolled was care- fully controlled at 1850°F. All plates were rolled to ¾-in. thickness, and tested in the as-rolled condition. The total number of steels prepared in the laboratory for this study was 95. The charge consisting of ingot iron and ferrosilicon equivalent to 0.10 pct Si was melted in a 200-lb induction furnace under an atmosphere of argon to insure low, uniform nitrogen contents. After the charge was melted and the desired temperature was obtained, the melt was partly deoxidized with either silicomanganese or aluminum. Aluminum was used for this purpose in only those steels with very low silicon contents, where the finished steel was to contain some aluminum. This initial deoxidizing addition was made to obtain consistent recoveries of subsequent additions of ferro-manganese, ferrosilicon, and aluminum. Carbon, in the form of graphite, was added, either just prior to tap or to the final aluminum addition. The entire heat of 200 lb was poured directly into a 6x6-in. big-end-up mold. The ingots of semikilled steel were capped with a steel plate. The killed steels, on the other hand, were poured with a hot-top containing 14 pct of the total volume of the ingot. The ingots were processed by heating to 2250°F, followed by forging to slabs 1¾ in. thick and 6 in. wide. After reheating to 2250°F, the slabs were rolled to 0.9-in. gage, using reductions of approximately 1/6 in. per pass. The 0.9-in. thick plates were immediately recharged in a furnace held at 1850°F. After 30 min in the furnace at 1850°F, the plates were rolled to ¾ in. in one pass. Following the final pass, the plates were stacked on edge on a brick floor, with a brick separating one from another, where they were allowed to cool in air. Drillings for chemical analysis were taken from the plates at locations corresponding to the top and bottom of each ingot. Carbon, manganese, silicon, phosphorus, sulfur, and nitrogen contents of each sample were determined. The analysis of each steel was carefully controlled so that the contents of

Jan 1, 1957

By AIME AIME

THIS year the Chairman of the Institute's Iron and Steel Division is THIS William Anderson Haven, better known to the membership generally as Bill Haven. The Division Chairman is an individual endowed with a broad perspective of the ferrous metal industry he result of his earlier experiences as a successful operating man in the working and management of blast furnaces and his later experiences as an engineering-consulting executive concerned with the design and erection of and steel works throughout the world. William A. Haven was born to iron steel in the Pittsburgh district on ;. 1, 1888, and in due time--or in 1909 graduated from Penn State with a Bachelor degree in industrial chemistry.

Jan 1, 1944

THE IRON HUNTER. By Chase S. Osborn, pp. 316, Ills. 10. The MacMillan Company, New York. 1919. An autobiography, the story of a Hoosier boy who fought his way to manhood and power through early misfortune and poverty, from street urchin and newsboy, to editor and author; from lumberjack and dock walloper to statesman and Governor of Michigan. The reader has the measure of the man in the first chapter, a dramatic recital of how the fighting boy editor cleaned up a lawless mining camp of 40 years ago. The thread of the narrative is the author's life-long devotion to outdoor living, ex-ploration and travel. Residing in Sault de Sainte Marie, Mich., in the heart of the Lake Superior country, he took his delight and, incidentally, found his fortune in prospecting the north woods for iron ore; eventually, extending his travels to the continents and many of the islands of the world, he discovered what, he believes-to be a great iron range in Madagascar. In this book there is plenty of anecdote, a great deal of wholesome social and po¬litical philosophy and some interesting sidelights on the characters of some of the author's prominent contemporaries in the political life of Michigan. The style is direct and animated, flavored and illuminated with the vernacular of Hoosierdom and the woods country of the North. The author levies on the vocabulary of the sciences and the classics for many a noun and adjective and, with Rooseveltian license, now and then coins a word. The reader's interest will be gripped from cover to cover, albeit he may occasionally need a dictionary. R. C. A.

Jan 11, 1919

By L. Graydon Carpenter, Donald E. Garrett

Probably the largest single tungsten deposit in the U. S. is one that has yet to produce any tungsten; it is not even listed in tables showing U. S. reserves. This deposit is at Searles Lake, Calif., where the brine contains about 70 ppm WO3. Small though the concentration is, the amount of brine in the lake is so great that it is estimated at 170 million lb of WO3 (8.5 million units), equaling the total of all other known reserves in the U. S. This dry lake is located in the basin formed by the Argus and Slate ranges in the northeastern corner of the Mojave Desert (Fig. 1). It consists of a massive salt body some 35 sq miles in extent, varying in thickness from 0 to 120 ft and containing more than 3 billion tons of salt. A central section of about L. G. CARPENTER and D. E. GARRETT are with the Research Dept., American Potash & Chemical Corp., Trona, Calif. TP 47881. Manuscript, Nov. 4, 1958. AlME Trans., Vol. 214, 1959. 8 sq miles is exposed salt; the remaining area is overlain by mud. Except for the exposed sodium chloride (10 to 15 ft thick) the body consists of a very complex and heterogenous mixture of soluble crystals, containing at least eight major phases. It is only about 53 pct solid, the voids being occupied by a dense brine which is the raw material for two chemical companies operating in the valley.

Jan 3, 1959

By J. W. Powell, F. H. Spedding

A complete review of the use of chelating agents in the sepa ration of rare earths by ion-exchange is given as well as a concise description of the recent pilot-plant operations of the Ames Laboratory. The two chelating agents which show the greatest promise are ethylenediamine-N,N,N',N'-tetraacetic acid and N'-(2-hydroxyethyl)ethylenediarnine-N,N,N '-triacetic acid. The first successful separations of rare earths by ion exchange were reported in a collection of papers which appeared in the November, 1947, issue of the Journal of the American Chemical Society.1'9 Some of this work was performed at the Ames Laboratory of the A.E.C., the remainder at the Oak Ridge National Laboratory. The processes developed at Oak Ridge, as well as some of the early Arnes methods, employed 5 pct citric acid-ammonium citrate eluant at low pH and were carried out on either H+-state or NH:-state resin beds. These techniques were successful for the separation of small quantities of either naturally occurring or radioactive rare earths and are still used for the isolation of rare-earth activities from fission products. Concentrated citrate is not economical, however, for use in moderate or large-scale rare-earth separations. For this reason, the Ames Laboratory turned its attention to lower concentrations and higher pH's in order to make more effective use of the eluting agent.10-14 Although elutions have been performed successfully over a wide range of conditions, 0.1 pct citrate at a pH of 8.0 is highly recommended for use on H+-state resin beds.15,16 Elu-tion with 0.1 pct citrate in the pH range from 5 to 9 brings about the separation of the constituent rare earths into a series of flat-topped elution bands which progress down the resin bed, head to tail, without actually pulling apart as do the rare-earth peaks which develop when trace quantities are eluted with 0.25M (5 pct) citrate at low pH's. Because of this, elution with 0.1 pct citrate at pH 8.0 do not produce pure rare earths unless sufficient quantities are present to provide developed bands which are at least several inches long on the columns. Although other eluting agents have proved more effective than citrate solutions, articles concerning the use of citric acid for separating rare earths still appear in the literature occasionally. For example, Ketelle and Boyd17 reported some further studies on the separation of rare earths with 5 pct citrate in 1951. They used 270 to 325 mesh Dowex-50 columns at 100°C and a pH of 3.28. vickery18 compared the effectiveness of a number of eluants for the separation of rare earths on NH+4 state Dowex-50 in 1952. He found that citric acid was more efficient than acetic, malic, tartaric, and aminoacetic acids. In 1953, Mayer and Freiling18 reported that citrate was inferior to malate, glycolate, lactate, and EDTA for the resolution of Sm-Eu and Y-Tb mixtures on 250 to 500 mesh, NH+4-state, Dowex-50 at 87°C. pinta20 used 5 pct citrate in the pH range 2.8 to 3.4 to obtain some rare earths for analytical work the same year. Trombe and Loriers21 reported the use of citric acid in their laboratory to separate rare earths in kilogram quantities. Lariers and Quesney22 reported some separations with citrate in 1954. They used 5 pct citrate at pH 2.8 to separate yttrium and the yttrium-group rare earths from the cerium-group rare earths. briers23 used 5 pct citrate at pH 3.2 and 90°C as late as 1956 to isolate thulium in fair purity. For the separation of tracer quantities of rare earths, Mayer and Freiling19 have recommended pH 5.00, 0.24M lactate at 87 °C on 250 to 500 mesh, NH+4-form Dowex-50. Freiling and Bunney24 have also employed lactic acid for the separation of fission-product rare earths. Cunninghame, Size-land, Willis, Eakins, and Mercer25 have reported a 4-hr separation of Y, Eu, Sm, Pm, Nd, and Pr with 1M lactic acid at pH 3.25 on Zeokarb-225 at 87°C. Stewart, et al.,26 reported separation factors for rare earths distributing between Dowex-50 and 0.25M glycolic acid. stewart27 also reported a 30-61 separation of Y, Tm, Er, Tb, and Lu tracers with buffered, 0.25M glycolic acid containing 0.05 pct Aerosol OT. The resin bed was 400-mesh Dowex-50 (X12). The pH of the ammonia-buffered eluant was 3.5. Various aminopolyacetic acids have also been used to obtain varying degrees of separation of the rare earths. In 1951, Fitch and Russell28 investigated iminodiacetic acid (IDA) and nitrilotriacetic

Jan 1, 1960

By Nicholas J. Grant, Michio Yamazaki

Cast copper alloys containing 10, 20, and 30 pct Ni and 0.75 to 0.80 pct Al were machine-milled into chips, then comminuted in a rod mill to fine flake powder utilizing a number of processing variables. The powders here internally oxidized, mostly at 800°C, in a low-pressure oxygen atmosphere. The consolidated powders were hot-extruded into bar stock. Room-tenmperature tension tests, stress-rupture tests mostly at 650°C, but also at 450° and 850°C, and hardness measurements after various annealing temperature treatments to study alloy stability were perfomted. Excellent room-temperature strength, high rupture strength at 650°C, and resistance to recrystallization at 1050°C were obtained. Problems in optimizing conditions for internal oxidation of Cu-Ni base alloys are discussed. THE interesting high-temperature properties of SAP' have stimulated considerable effort in the study of more refractory alloy systems where the potential for high-strength alloys at high temperature is great.2-13 A number of methods have been utilized to produce the desired fine, hard particle dispersions, of which internal oxidation2,9,7 of dilute solid-solution systems offers considerable promise by virtue of the potential for producing ultrafine, well-dispersed oxides. While most of the published works are concerned with pure metal matrices, a number of investigators have studied the effects of solid-solution strengthening.10,19 Use of more complex alloy matrices (for example, aging systems) has been unsuccessful because overaging still occurs at high temperatures in the oxide-containing alloys.14.15 Solid-solution strengthening is, however, effective at very high temperatures9,10 and might be expected to contribute importantly to the strength of oxide-dispersion strengthened alloys. For this study, internal oxidation of solid-solution alloys of copper and nickel, containing small amounts of aluminum, was chosen as the method of alloy preparation. PREPARATION OF ALLOYS Three copper alloys containing about 10, 20, and 30 pct Ni and each containing 0.75 to 0.80 pct A1 (enough to yield about 3.5 vol pct alumina) were prepared as air-cast ingots measuring 2.5 in. diameter by 6 in. high (see Table I for the analyses). Processing steps for all the alloys were as follows (also see Table 11): 1) Homogenization of the ingot at 982°C (1800°F) for 45 hr in an argon atmosphere. 2) Machine milling of ingots into fine chips. Average thickness was about 0.1 to 0.2 mm. 3) Hydrogen reduction of chips at 593°C (1100° F) for 1 hr to reduce copper and nickel oxides. 4) Rod milling of chips to finer powders. 5) Hydrogen treatment of powders as in step 3. 6) Internal oxidation of the powders. 7) Hydrogen treatment of oxidized powders as in step 3. 8) Hydrostatic compression of evacuated powders. 9) Sintering of compacts in hydrogen. 10) Hot extrusion. Variations in processing among the alloys were made in steps 4, 5, and 10 (see Table 11). In the past, two methods were utilized to internally oxidize alloy powders. Preston and Grant3 surface-oxidized dilute Cu-Al powders to obtain the necessary amount of oxygen to oxidize the solute metal (aluminum and silicon), and then permitted the formed copper oxide to diffuse and react with the solute in an argon atmosphere. Bonis and Grant4 exposed Ni-A1 and other nickel alloys to an oxygen pressure derived from the decomposition of nickel oxide at a preselected temperature, in an argon atmosphere. Both methods are applicable and can be modified to generate a range of oxygen pressures for oxidation of the solute but not the solvent metals. Procedure I: Surface Oxidation of Alloy A3, Cu-10Ni-0.76A1. Powders of -20 to +28 mesh were surface-oxidized at 500°C (932°F) to obtain the desired amount of oxygen for oxidation of the aluminum to alumina; the powder was then sealed in Vycor and heated at 900°C (1652°F) for various times up to

Jan 1, 1965

By C. Schlumberger

SINCE the beginning of .the year 1928 the senior authors and their associates have applied a series of procedures which makes possible the detailed study in situ of the formations traversed by a drill hole before the casing has been landed. They have given the name "electrical coring" to the ensemble of these processes, which now replace in a large measure the mechanical coring performed by the drillers, and permit the gathering of bottom-hole data hitherto unobtainable. Three years have elapsed since the technique and interpretation of these measurements emerged from the experimental stage and entered the field of industrial application on a large scale. The total length of drill holes so far surveyed by the authors and their associates, all over the world, amounts to several millions of feet. Practical and strongly built equipment has been evolved, which permits the examination in a short time of an open hole several thousand feet long. No comprehensive paper has yet been published discussing the essential principles of the processes applied and bringing into evidence their economic interest. This is the object of the present paper.1 Numerous examples of field work performed under varied geological conditions are given, constituting a concrete illustration of the services rendered by the new methods. The study in situ of the formations penetrated by a drill hole is based on the measurement of a given physical factor or parameter associated with these formations. Generally. the measurements are made syste-matically along the whole length of the open hole. The physical factors or parameters which are now utilized by us to this end are: (1) the resistivities of the rocks; (2) their porosity; (3) their electrical anisotropy; (4) their temperature; (5) the resistivity of the muds. In order to

Jan 1, 1932

By J. R. Craig, T. N. Solberg, M. A. Linden

The central and southern Appalachian Mountains were the major sources of domestically produced gold throughout the first half of the 19th century and continue to yield gold today. Small amounts of gold were probably extracted by the Indians and the Spaniards but the first documented report of gold in the region was made by Thomas Jefferson who found, in the Rappahannock River of Virginia in 1782, a 1.8 kg (4 lb) lump of gold ore that yielded 26 g (0.85 oz). Gold was subsequently discovered in North Carolina between 1793 and 1799, in Virginia in 1806, in South Carolina in 1827, in Georgia in 1829, and in Alabama about 1830 (Becker, 1894-5; Pardee and Park, 1948). Production climbed to more than 933 kg/a (30,000 oz per year) between 1830 and 1852, but dropped sharply after the California gold rush in 1849 as experienced miners moved west in search of bigger and easier stakes. The Civil War briefly halted gold mining in the Appalachians, but production rose to an average of about 249 kg/a (8,000 oz per year) from 1865 until 1878 and to about 404 kg/a (13,000 oz per year) from 1881 until 1915 when it again fell to near nil (Pardee and Park, 1948). Minor resurgences occurred in the 1930s and 1940s. Although there has been no reported production in recent years, it is likely that "weekend panners" still remove hundreds of ounces from streams annually. The total reported production for the area through 1959 is more than 77 t (2.5 million oz). This paper reports some initial findings of a long-term project designed to investigate the mineralogy, chemistry, mode of occurrence, and petrology of gold occurrences in the Appalachians. The goal of the initial phase was to determine the compositional range of gold in the Appalachians as a step toward deciding if sufficient variations were present to allow the definition of "compositional signatures." The very few published data on gold fineness in the Appalachians are based on assays that commonly include gold and silver from several mineral species. Analyses in the present study were performed on individual grains of electrum using a spot size of 10 µm x 10 µm to 100 µm X 100 µm (394 X 394 micro in. to 3,940 X 3,940 micro in.), and thus reveal the true composition of the principal precious metal-bearing phase.

Jan 1, 1984

ATHOUGH the open-hearth charge contributes CO, CO2, and water vapor to the combustion gases and absorbs oxygen from them, in the main the thermal effects in the melting charge and molten bath can be considered independently of those in fuel combustion, the latter being regarded simply as the source of any extra heat required to finish a heat of steel. First of all, it should be remembered that a large percentage of the heat supplied to the bath is furnished by oxidation of the various elements in the charge itself. If this charge consisted of 80 to 100 per cent of hot metal and the oxidation were obtained by blowing in air or oxygen, as is the case in the Bessemer converter, then the net heat absorption would be negative, that is, the bath would contribute part of the heat required to keep the melting chamber hot, in addition to that contained in the finished steel and slag. In actual open-hearth practices, probably the nearest approach to this is in the duplex furnace, charged with Bessemer-blown metal and some hot metal, where very little heat is required to complete the refining and nearly all the heat energy from fuel combustion is used to keep the roof and walls of the melting chamber up to around 2900 to 3000°F. (1600 to 1650°C.) so that the bath will not cool off during the refining. The other extreme is with all-cold charges containing around 80 per cent steel scrap and 20 per cent cast iron or cold pig iron, in which case a very large proportion of the heat in the bath at tap is supplied from the fuel combustion. THERMAL EFFECTS IN MELTTNG In the previous chapter it was pointed out that in a typical heat, the fuel furnishes about four million B.t.u. per ton of steel produced. The heat required for the metallurgical processes is not easily defined in useful manner (as is shown later), but it ranges downward from about one million B.t.u., depending not only on the charge but on the manner of calculation. In any event this requirement appears quite small in comparison with the heat furnished by the fuel and invites

Jan 1, 1944

THE following employment items ore made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service ore at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., Son Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if. placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Graduate Mining Engineer, 31, married. Six years' engineering experience, mining and construction, U. S. A. and Alaska. Underground metal mining, production, development, geology, mine engineering. Engineering on airfield construction, earthwork, location work, mapping, topography, road location; office work. Commercial pilot license. Desires position mining or construction. Available 45 days. Prefer Latin America. M-676-477-E-8-San Francisco. Mining Engineer, 42, married, one child. Fourteen years' mining with much supervisory experience in developing and operating metal mines; also mine safety engineering. Familiar with many large and small mines in the western U. S. and Mexico. Excellent references. M-677.345-E-1¬San Francisco.

Jan 1, 1952

By H. M. Chance

The iron-ore deposits of the Hartville district are located near the new town of Guernsey, about 100 miles north of Cheyenne. The writer has been familiar with them since 1887, having visited the district several times for different clients— his last examination having been made in November and December, 1897. The deposits extend in a general N.E.-S.W. direction from a point in Section 33, Range 65 W., Township 28 N., on the west side of Whalen cañon, through Sections 4, 5, 6, 7 and 8 of Township 27 N. in the same Range, and over into Sections 1 and 12 of Township 27 N., Range 66 W. General Characteristics. The ore is a remarkably pure red hematite, extremely low in phosphorus, and carrying a small percentage of silica, as shown by analyses given below, and similar in many respects

Jan 1, 1901

By J. B. Newkirk, A. H. Geisler

The alloy Cu4Pd has a disordered face-centered-cubic structure when quenched from temperatures between 478ºC and the melting point (about 1100°C). Below 478ºC an ordered phase is stable. The results of a Debye-Scherrer X-ray analysis indicate that the ordered phase has a tetragonal unit cell described by the space group C24h — P42/mt with 2 Cu in 2a, 2 Cu in 2f, 4 Cu in 4j (x = 0.2, y = 0.6), 4Pd in 4j (x = 0.4, y = 0.2), and 8 Cu in 8k (x = 0.1, y = 0.3). The orientation relationship between the face-centered-cubic phase and the ordered tetragonal phase is given by: [100],,. // [130]al,. COO1Ia.d.//COO1I,,.. • The behavior of Cu,Pd is typical of ordering alloys except that the transformation is very sluggish. The increase in hardness and the microstructural and X-ray diffraction effects are interpreted in terms of coherency strains caused by the ordering. AN anomalous construction in the Cu-Pd phase diagram (Fig. 1) was reported in 1939 and has been allowed to stand without further published attention since that time. The odd figuration about the composition 10 to 27 atomic pct Pd is derived mostly from the work of Jones and Sykes.1 Evidently several features of this binary system require further study if the constitutional forms are to be well understood. The present paper includes a study of one of these features, that is, the crystal structure of a single ordered alloy containing nominally 20 atomic pct Pd. This choice of composition was suggested by the work of Harker and associates who determined the structure of Ni4Mo2 and Ni4W.3 The nature of the ordering process in Cu4Pd was studied also by observing the hardness, microstructure, and Debye-Scherrer patterns of specimens which had been aged at various temperatures after quenching from an initial disordering treatment. Experimental Methods A 20 gram ingot of Cu4Pd was made by melting spectrographically standardized copper from Johnson, Matthey, and Co., and commercially pure (99.5 + ) palladium in an argon-filled quartz tube. Chemical analysis showed that the ingot contained 80.0 atomic pct Cu. The ingot was rolled about 60 pct to a strip 0.060 in. thick and was homogenized for 16 hr at 950°C in low pressure argon. Rods cut from the rolled strip were worked into wire 0.015 in. in diameter, and specimens for hardness and microscopic examination were cut from the remaining strip. All specimens, with the exception of some of the wire, were given an initial disordering treatment by heating for 16 hr at 950°C, followed by water quenching. A 10 cm length of as-drawn wire was water quenched after being held in a temperature-gradient furnace4 for 89 days. Room-temperature Debye-Scherrer photograms were then made at points along the wire to determine the temperature below which the ordered phase was stable. Although the accuracy of temperature determination in the gradient was only about ±10 °C, the temperature gradient was sufficiently gradual that the sensitivity was much better and locations which had differed by as little as 1°C could be distinguished. An analysis of the crystal structure of the well ordered alloy was made by X-ray diffraction using a specimen cut from this wire. The change of Debye-Scherrer pattern as ordering progressed was studied by using isothermally aged samples of initially disordered wires. The wires were sealed under low-pressure argon in small quartz tubes for heat treatment. After the aging treatment, the tubes were quenched in water and photograms were made at room temperature in a 10 cm diam camera using filtered Cu kX. (A = 1.540511) Hardness was measured on a Vickers hardness tester using a 10 kg load and 2/3 in. objective lens. Reported values are the average of at least three impressions made on flat specimens 0.060 in. thick. After the hardness of a heat-treated sample had been measured, it was resealed in low-pressure argon and returned to the furnace for continued aging at the same temperature. In this way, two samples served for all aging times at each temperature. Hardness specimens which had been aged 500 hr or more were used for metallographic examination after the final aging treatment. A dilute potassium-dichromate etching solution was used.

Jan 1, 1955

By E. H. Jr. Dix

OF all the alloying elements used in commercial aluminum alloys, copper stands out as by far the most important, and it is perhaps for this reason that the constitution of the aluminum-copper system has received the attention of a number of experimenters covering a period of approximately 20 years. It would be expected that during this time the equilibrium relations had been thoroughly and exactly worked out. In a general way this is true, but there is a surprising lack of agreement in the details of the high aluminum end of the diagram, particularly in regard to the solid solubility of copper in aluminum, which has been given variously as 2 per cent. to 5 per cent. at the eutectic temperature. The importance of this is much greater than might at first appear to one unfamiliar with modern commercial aluminum alloys. This is true because, with one exception, the susceptibility of the strong alloys to heat treatment depends, in part at least, upon the solid solubility relations of copper in aluminum. In 1919, Merica, Waltenberg, and Freeman1 published the first detailed information on these solubility relations. They found that the solubility of copper decreases with falling temperature from about 4 per cent. at 5.25° C. to about 1 per cent. at 300° C. and is apparently still diminishing at lower temperatures. In 1921 there was published a brief account of the results obtained in the National Physical Laboratory, Teddington, England.2 This laboratory, however, reported that 5 per cent. of copper is soluble in aluminum at 540° C., and that this amount decreases to about 3 per cent. at 20° C.

Jan 2, 1926

By J. P. Smith

Permian salt measures carry extensive lenses of soluble potash salts in north central Germany. Potash deposits of Oligocene age are found in the Upper Rhine Graben of Alsace (France), and in the Catalonian Basin of Spain. These deposits are found in a wide range of structural settings. Reserves are large, and the production of potash salts is an important phase in the economy of each of these countries.

Jan 1, 1950