Search Documents

By Maurício Covcevich Bagatini, Maycon Athayde

Nowadays, the HPGR (high-pressure grinding rolls) is an intermediate step between filtering and balling in the most modern iron ore pelletizing operation. The operation debottlenecks filtering process and reduces pressure over the typical milling process to control particle size to the balling. The present study evaluated aspects of microwave application to the iron ore concentrate fed to HPGR in a bench scale unit. Iron ore concentrate was irradiated varying the microwave exposure time and grinding efficiency was evaluated. The moisture influence in the HPGR efficiency was also assessed. The pellet feed blaine surface area (BSA) improved by 300 cm2/g and % < 325# fraction by 3%. Scanning electron microscope (SEM) images show the formation of micro-cracks onto the particle surface induced by microwave; the effect observed helped improve the milling process performance, in addition to the moisture reduction observed due to the temperature increase.

By Margaret E. Harris

The formation of nitrogen oxides, the decay of carbon monoxide, and the concentrations of residual hydrocarbons in the secondary combustion zones of propane-air and methane-air flames were studied in three enclosed burners designed to simulate gas appliances such as space and water heaters. The effect of thermally or chemically perturbing the combustion gases above these flames was determined theoretically and by means of factorial experiments. The concentrations of air pollutants and the flame temperatures were measured, and the effects of ingress of secondary air into the primary and secondary combustion zones, flame stability, burner port surface, and simulated recycling of combustion gases were noted. Based on this study, four principles were derived that, applied to gas appliance design, will insure minimal emissions of these air pollutants: 1. Oxides of nitrogen can best be kept low by depressing peak temperatures to about 3,050° F. 2. If this is not possible, then the secondary combustion zone should be cooled rapidly to this temperature. 3. Carbon monoxide concentrations can be limited by rapid induction of secondary air. 4. Hydrocarbon concentrations can be controlled by designing for well-seated, stable flames. In addition, empirical reaction rates were derived that predict the concentrations of nitrogen oxides and carbon monoxide in the primary and secondary combustion zones.

Jan 1, 1970

By M. Neven, R. A. Steane, E. Lam

"The Key Lake uranium mill is located in Northern Saskatchewan. It treats a high grade, complex uranium and metal sulphide ore. The plant and process are in many respects unique, because commercial treatment of this type of uranium ore had never been done before. The process and engineering design was based on extensive laboratory test results. A pilot plant testing stage was omitted because of confidence in the test results and time constraints to bring the plant into production.The bench scale testwork on exploration drill core samples along with preparation of the feasibility study and environmental impact statement were carried out between 1976 and 1979. The contract for detailed engineering was awarded to Wright Engineers of Vancouver in late 1980 and in August of 1981 following a public inquiry, approval to proceed with construction was granted.Construction began immediately, and during the winter the foundations for many of the plant buildings were poured and by the beginning of the following winter the buildings had been erected and installation of equipment began. Despite a six month construction worker strike in 1982, the crushing plant started up in June of 1983 and ore processing commenced in October of that year, approximately 3 months behind the original schedule.This paper describes the mill design and compares the expected performance, with the operating experience. Emphasis is directed towards flowsheet and equipment changes made since start-up, operational difficulties encountered and further improvements envisaged. Auxiliary systems are only discussed where they directly affect mill operation."

Jan 1, 1986

By Paulo Braga, Carlos Junior, Silvia França

"Lithium is the lightest of the metals, with high reactivity and great electrochemical potential. It has a low thermal expansion coefficient and high caloric value, and it forms very light and resistant aluminium alloys. These properties make lithium an attractive element for use in battery manufacture and glass and ceramics production, in addition to its applications in the aeronautic industry. Today, two sources of raw material are economically viable for lithium production: pegmatite rocks and brine. The world production, in 2012, was approximately 150,000 tons of LCE (lithium carbonate equivalent), almost triple the production in 2000. The forecasted consumption for the current year, 2013, was approximately 162,000 tons of LCE, and for 2020, it could be as much as 280,000 tons of LCE, stimulated essentially by the growth of world production of electric (EV), hybrid (HEV) and hybrid plug-in vehicles (PHEV), the batteries of which are based on Li-ions. With the growth of world demand and increasing prices, lithium minerals such as spodumene, petalite and amblygonite, once considered uneconomical for the production of lithium carbonate, are regaining their economic value. New projects to produce lithium compounds based on mineral sources are being developed in many countries, aiming to produce battery-grade lithium carbonate (99.95% Li2CO3). Although Brazil has large lithium pegmatite reserves, the domestic production of lithium carbonate and hydroxide is very low, at approximately 600 tons of LCE, which represents 0.4% of the world production. The application of these products is mostly in the grease and ceramic industries. The national lithium market is under government protection due to its potential use for nuclear purposes. Thus, the industrialization activities and import and export of ores and lithium minerals, as well as organic and inorganic products, such as metallic lithium and lithium alloys, are controlled by the National Commission for Nuclear Energy (Comissão Nacional de Energia Nuclear - CNEN). The objectives of this work to quantify the real lithium demand in the Brazilian market, considering that a large amount of lithium is indirectly imported in the form of the Li-ion batteries used in equipment such as mobile phones, cameras, tablets, notebooks and e-bikes, and to compare this demand with the current national production of LCE. Finally, some technological alternatives will be discussed, with the aim of increasing the competitiveness of the lithium industry in Brazil."

Jan 1, 2014

By A Hekmat, M Fuentes, F Armijo, R Castro, F Rodriguez

Interpreting the behaviour of granular material and simulating the gravity flow are complex processes in cave mining methods. In this paper, a new Cellular Automata based code – FlowSim – is used as a flexible tool to simulate the gravity flow and subsidence zone in block caving mines. The simulation results of the gravity flow model in a real scaled mine as well as a scaled physical model are presented in this study. In this research, FlowSim was first calibrated at a mine, based on the information obtained from smart markers. These markers were located in five points of the second block of the Esmeralda sector, at the El Teniente copper mine, Codelco, Chile. The calibration was performed with the objective of reducing the discrepancy between the extraction zone defined by markers in the mine and FlowSim outputs. Regarding the mine data, FlowSim was calibrated with the minimum error of ten per cent between real and simulated results. Then, the calibrated FlowSim model was used to simulate the flow behaviour of a scaled physical model. This model was constructed in the Block Caving Laboratory of the University of Chile to scale down the same block of the Esmeralda sector with the scale of 1:200. The FlowSim outputs show that this software enables the simulation of the gravity flow of the scaled model with less than five per cent discrepancy in grade and dilution entry to the drawpoints. According to the obtained results, this paper recommends FlowSim as an appropriate tool which can improve the design of production level in block caving and can enhance the prediction of the subsidence zone and dilution entry.CITATION:Castro, R, Hekmat, A, Fuentes, M, Armijo, F and Rodriguez, F, 2016. FlowSim – a versatile flow simulation tool to quantify extraction and design alternatives for block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 645–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Steve Kral

Improved metals and other commodity prices have caused the mining industry to open new mines, re-evaluate development opportunities at potential mines and increase production at existing ones. This sense of renewed optimism is being seen at operations and development projects around the world. Except in the United States. The regulatory structure there has not allowed the domestic industry to share much in mining’s resurgence. It can still take up to 10 years to permit a new mine. And, while Clinton-era regulations regarding mill sites have been put on hold, existing mines that wish to expand operations still face significant regulatory and environmental hurdles. But things may begin to improve in the United States.

Jan 1, 2005

Development of New Comminution Testing Methodologies for Geometallurgical Mapping of Ore Hardness and Throughput The emerging discipline of &apos;geometallurgy&apos; is becoming increasingly recognised as a discrete and high-value activity that reflects an ongoing trend towards more effective mine site integration and optimisation. Constrained sampling that reflects and defines inherent ore body variability is a key geometallurgical requirement. This requires use of larger numbers of low-cost physical testing which can be applied to small sample volumes suitable for defining natural variability. The AMIRA P843 &apos;GeMIII&apos; project (Geometallurgical Mapping and Mine Modelling) is a major industry-supported research initiative designed to develop new tools, methods and protocols to support geometallurgical integration. As part of this integrated research a new more rapid low-cost comminution test (GeM Comminution index) has been developed which can be employed as a front line tool for geometallurgical mapping purposes and predictive throughput modelling. The test has been designed to be inserted into routine assay sample preparation and is based on constrained jaw crushing protocols linked to analysis of resultant size distributions. Extensive validation and modelling has shown the GeM Comminution Index (Ci) is correlated with the Drop Weight index A*b and Bond Mill Work Index (BMWi). Large scale trials have been conducted within a commercial assay laboratory to demonstrate and optimise incorporation of the Ci test into routine sample preparation protocols. While Ci based estimates of A*b and BMWi are not as precise compared to larger volume more expensive test-work, the ability to undertake large numbers of tests typically in a systematic down-hole manner, provides a high level of data support through adjacency. A Ci based approach is highly suitable for variability mapping, domaining and selecting large composite samples for more precise testing. Within the context of the AMIRA P843 project this forms part of an integrated work flow designed to support geometallurgical integration. The development of a comminution test linked to routine assay sample preparation represents significant value adding to a process that in most cases is already going to be carried out. This paper introduces the Ci test concept and application to geometallurgical testing for throughput modelling

Sep 13, 2010

By O. Dojcar

The results of a laboratory investigation of rock fragmentation conducted with a model material were partially verified under field conditions. The object of the investigation was to study the qualitative and quantitative relations between the parameters of the primary blast and fragmentation to enable the planning of an economically efficient degree of disintegration with optimum utilisation of the blast energy. The three blast parameters that were considered were burden, specific charge and the ratio of spacing to burden

Jan 1, 1991

By R. L. Zick, J. D. Byars, T. P. Mucho

Recently, a large Pittsburgh seam longwall mine was nearing depletion of a major portion of its current reserves and had begun to develop in a different direction from its original portal area to access additional reserves. This meant that a large area of the mine would be abandoned and sealed. However, continued use of the original mine portal area required that the water accumulating in the abandoned mine would eventually need to be pumped to the surface. This would be in addition to the discharge water associated with the new portion of the mine. Several pumping and sump options were investigated to handle the quantity and quality of the anticipated discharge water. This paper describes some of these options, their advantages and disadvantages, and the final engineering decisions. Some problems and unanticipated outcomes, as well as the eventual solutions are discussed, including: (1) estimates of pump requirements, (2) water pool size, (3) eventual water quality, (4) anticipated inflows, and (5) integration into the overall mine water system.

By J Belke

Murrin Murrin Operations have not had a successful beginning. Numerous reliability and operability issues, many of which are the result of design decisions, have been addressed through mechanical and operational changes and the CCD circuit is no exception. Four design aspects of the CCD circuit that have caused and continue to cause operational problems are: the inclusion of solution neutralisation gypsum in the CCD circuit feed which was designed solely for HPAL residue without proper investigation of its impact on the achievable underflow density and resulting wash efficiency; the decision to construct the thickener base from thickened solids; the lack of redundancy in the overflow, underflow and tailings pipe work; and the lack of thickener operational flexibility in the central rake-lift and feedwell dilution system. In November 2002, the lack of operational flexibility in the rake-lift and the feedwell dilution system was improved through mechanical modification as follows:CCD1 rake mechanism was modified to allow central vertical lift of 600 mm; and CCD1 changed to forced dilution using the Outokumpu TurbodilRântechnology by replacing the E-DucânRtechnology of Eimco. The installation and the results of the CCD1 rake-lift mechanism and feedwell dilution system changes are discussed in this paper.

Jan 1, 2004

By Mark E. Schlesinger

Engineering design follows a six–step sequence. Demonstration of this sequence in materials engineering is less common. A case study is presented, using the 1989 paper by Gafner on the development of 990 gold-titanium alloy. This paper identifies a need, develops the problem, identifies alternatives, demonstrates the use of metallurgical principles to identify alternative responses, and shows how more favorable options are selected. The paper can also be used to illustrate engineering design as an iterative process. The paper is also useful as a starting point for more in-depth examination of specific elements of the design process, and lends itself to the creation of student exercises.

Jan 1, 2014

By Alcides Eloy Cano

Los recursos minerales de un depósito está en función de las dimensiones de la geometría del cuerpo mineral, así como sus reservas minables permiten saber el verdadero valor económico de su contenido. En este sentido, la Geotecnia es una herramienta que define las condiciones de los esfuerzos in situ, predice el comportamiento alrededor de excavaciones subterráneas e interactúa con las labores próximas, así como también la distribución de esfuerzos. Por ello, el presente trabajo señala la aplicación de esta herramienta a una mina subterránea de Oro localizada en el Perú, donde se tiene bloques de mineral económicos, así como señala su accesibilidad con leyes encima del Cut-Off. De forma que se recupera el mineral económico a través de las rutas críticas de carguío, en función de la viabilidad de autosostenimiento.

Sep 12, 2011

By R. A. Bergman

"Process descriptions are provided for the following ten plants that treat high-magnesia lateritic nickel ores (saprolite) by pyrometallurgical means: PT Aneka Tambang; Cerro Matoso S.A.; Falconbridge Dominicana C. por A.; Hyuga Smelting Company Ltd.; Larco (Societé Minière & Métallurgique de Larymna); Loma de Niquel; Le Nickel, SLN-Eramet; Nippon Yakin Kogyo Company Ltd.; Pacific Metals Company Ltd.; and PT Inco Indonesia.Flowsheets, equipment information,chemistry and production data have been compiledfor plants based on both information providedby the companies and on calculated massand energy balances.IntroductionNickel is of vital importance to modern society. Without it, we would not be able to enjoy many of the things that we take for granted, such as computers, airplanes and stainless steel appliances in our homes and workplaces, to mention a few.Nickel occurs in nature both as sulphide and oxide ores. Approximately 36% of the nickel reserves in the Western World occur as sulphide and 64% as oxide ores. Sulphide ores respond to concentration processes, whereas, oxide ores do not. Sulphide ores mined at 1% nickel can be readily concentrated to 10% nickel, whereas, oxide ores cannot be concentrated and therefore have to be processed as mined.Laterite ores are normally classified intotwo groups:1. The high-magnesia ores, saprolites or serpentines, are, as a rule, processed by smelting. The main reason for this is that the nickel replaces magnesium in the magnesium-silicate lattice. To be able to recover nickel, the lattice has to be destroyed. This can be achieved by smelting under reducing conditions.Acid leaching is also possible, but in this case, large amounts of MgSO4 or MgCl2 will be produced making it costly to regenerate the acid.2. The high-iron, low-magnesia ores are known as limonite. The nickel is relatively loosely bonded to goethite and hence can be recovered by selective reduction followed by ammonium-ammonium carbonate leaching. In recently developed processes, these ores are also being extracted by acid pressure leaching, with high Ni and Co recoveries.This paper focusses on the production of ferronickel and nickel matte from the highmagnesia ores."

Jan 1, 2003

By Matthew E. Meyer

Renovation, rehabilitation, restoration and expansion of existing residential, retail, commercial, hospital facilities and historic structures requires assessment and evaluation of foundation systems of various ages. The concept of demolition and reconstruction in urban areas is often more challenging, costly, and even prohibitive in some cases due to historic regulations. The authors have been involved with numerous projects related to existing foundation assessment and retrofit, including: hotel and hospital expansions, historic Art-Deco hotel renovations and expansions, garage structure expansions, additions to prominent auction houses, casinos, printing facilities; high-rise structure foundation retrofitting; forensic evaluations of existing building and highway structure foundation systems, and marine bulkhead sheeting systems. The use of non-destructive testing techniques, high-strain dynamic load testing, full scale pile cap load testing and 3-D laser scanning technology has proved to be vital in the assessment and evaluation process, as well as design of foundation retrofit alternatives. This paper presents various methods and techniques to facilitate a phased approach for optimization of existing foundations and subsequent re-use of foundation systems. These methods and techniques are illustrated through the author?s experience and selected case histories from projects with varied foundation and geologic conditions.

Jan 1, 2011

The discussion which followed the publication of my paper by the formert has, I think, enhanced its value. It may therefore be of interest to members of our Australasian Institute, who are not members of the Institution of Mining and Metallurgy, if I give a synopsis of the discussion.My attention was drawn to the fact that my paper did not make clear the extent of the improvement in furnace operations, which followed the use of coke of high quality; this comment applied more particularly to the lead content of slag. My failure to supply comparative figures in regard to the lead content of slag was governed by a condition which, I think, is of interest to metallurgists. As a result of industrial...

Jan 1, 1932

By F. Charette

The paper reviews recent investigations of the impact of corrosion on the performance of both plain and coated Swellex rock bolts. It addresses the problems associated with estimating and predicting corrosion rates of friction bolts, and based on field data it suggests an empirical relationship to predict corrosion rates. A review of the necessary qualities for a protective coating leads to recent experience with coated Swellex bolts that suggest that they can contribute to extending the useful life of Swellex bolts in potentially corrosive environments.

May 1, 2004

By Bernard H. Hertlein

All methods of deep foundation construction present challenges to the contractor and engineer that vary according to the method employed, and the geotechnical conditions in which it is being used. Augered-Cast-In-Place (ACIP) piles are generally regarded as one of the most challenging, because the construction method precludes the use of traditional shaft inspection and quality control techniques. Application of Nondestructive Test (NDT) methods can provide quality control for ACIP shafts that traditional methods cannot, but each NDT method has limitations. These make some NDT methods unsuitable for use on ACIP shafts, and may limit the effectiveness of others, depending on geotechnical conditions. To help contractors and engineers working with ACIP piles select the test method most appropriate to specific site conditions, this paper presents a summary of the major NDT methods currently available, and reviews their capabilities with respect to the unique conditions presented by ACIP pile construction. Case histories illustrate how a combination of careful method selection, skilled data interpretation, and experienced engineering judgment have resolved problems and ensured quality in foundation construction by discriminating between potentially serious defects, and those that are unlikely to be significant.

Jan 1, 1997

By Yasuo Ojima

A new copper continuous converting process was investigated to evaluate the possibility of its application in the commercial operation. The tests were performed both in the laboratory and in pilot plant scale. Bath smelting process with the use of the top submerged lance technology was applied in these tests. Furnace shape was modified to a lengthwise eylindrical one with a settling area. The furnace monitor was put in the settling area to check the furnace from inside, FeOx-Si02, FeOx-CaO and FeOx-CaO-Si02 based slag systems were used to check their efficiency, The optimum slag chemistry to have good metallurgical results was discussed and FeOx-CaO system with some Si02 content turned out to be preferable although it has not been practically used, In this pilot plant test feeding rate of I tIH of solid grain matte was charged consecutively for two weeks and continuous converting could be done successively. This process is expected to overcome the problems of existing processes and be easily applied in existing plants.

Jan 1, 2003

By G. A. Bezuidenhout, J. Davis, S. Lefume, J. P. T. Kapusta, D. K. Chibwe

"Although the centennial of the Peirce-Smith (PS) converting process has recently been celebrated, the technology has essentially not changed much since its inception. PS converting is used extensively in the Cu, Ni and PGM industry to remove iron and sulphur from a molten matte phase. A typical PS converting process would use low pressure air supplied by a blower to bubble air through the molten bath. This bubbling injection regime is inherently inefficient from a process and energy consideration. In the late 70’s and early 80’s, Brimacombe and co-workers demonstrated at both laboratory and plant scales that sonic injection (jetting regime) into copper or nickel converters could reduce or eliminate the above hindrances characteristic of PS converting. Since then, in spite of these successes, very little industrial applications have made headway in the converting process of non-ferrous metal mattes on a commercial scale. As part of its operational improvement and energy reduction program (process efficiency), Lonmin Platinum decided to conduct a full scale industrial evaluation of sonic injection using air only to establish if punchless, high efficiency sonic injection was feasible in its small 3.05 × 4.57 m converters (10’ × 15’). A plant trial was run for four weeks in one of its three converters. This paper discusses the plant demonstration with a focus on the experience acquired by Lonmin together with the key learnings from the trials. Reference will also be made to the commercial aspects of a full scale implementation of sonic injection in all three converters in the smelter. INTRODUCTION AND OBJECTIVESAlthough the centennial of the Peirce-Smith (PS) converting process has recently been celebrated (Peirce and Smith, 1909; Southwick, 2009), the technology has essentially not changed much since its inception. PS converting is used extensively in the Cu, Ni and PGM industry to remove iron and sulphur from a molten matte phase. A typical PS converting process would use low pressure air supplied by a blower to bubble air through the molten bath. This bubbling injection regime is inherently inefficient from a process and energy consideration."

Jan 1, 2012

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006