Search Documents

By Robert J. Maron, Mark Fernald, Alex Van der Spek, O’Keefe. Christian, Tim Bailey

"Sonar array-based non-invasive flow measurement technology is becoming an accepted and many times a preferred method of measuring challenging single and multi-phase flows in the mineral processing industry. This fundamental sensor and measurement technology has been extended to two developments that provide new measurement capabilities useful for monitoring and managing slurry flows and pipes.The first development is the non-invasive measurement of real-time velocity profile of slurry flow in horizontal pipes. Multiple non-invasive passive sensors measure localized velocities and are combined to provide a velocity profile measurement. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities and/or higher solids concentration while avoiding solids deposition or plugging and its associated operational costs.The second development is the non-invasive measurement of pipe wear on slurry lines. Presently, such measurements are made by hand-held portable ultrasonic thickness gages. The numerous shortfalls associated with the manual method are overcome with a set of permanently or semi-permanently installed transducers clamped onto the outside of the pipe. This ring of sensors contains a series of conformable ultrasonic transducers spaced around the circumference, which are used to measure the thickness of the pipe under their respective locations. Compared to manual methods, this system and approach results in better repeatability and accuracy. It also decreases inspection labor costs and pipe access requirements. The minimal accuracy variations in the presence of varying environmental temperatures will be shown. Trending of pipe wall thicknesses in high wear pipelines will be illustrated. The benefits of significantly improved pipe wear monitoring in hydrotransport lines with abrasive solids, and associated improvement in the ability to insure safe operation and avoidance of costly environmental damage due to leaks caused by pipe wear will be discussed."

Jan 1, 2009

By Roy A. Imbsen

Following the 1989 Loma Prieta earthquake, California Department of Transportation (Caltrans) expedited an effort to evaluate and retrofit important state-owned toll bridges to en­hance performance of the state's transportation systems during and after major (credible) earthquake events. Imbsen and Associates, Inc. (IAI) along with their sub-consultants, were awarded a contract to conduct seismic evaluation and to develop retrofit design for Benicia-Martinez Toll structure, to meet a "Serviceable" performance requirement after the event of a "Safety Evaluation Earthquake." This paper describes the design and construction specifications for the deep foundations supporting the main spans of the Benicia-Martinez Bridge. Benicia-Martinez Toll Structure (George Miller Bridge), a high-level deck-type welded truss bridge with welded girder approach spans, carries Interstate Route I-680 over the easterly end of Carquinez Strait near San Francisco, CA. The nearly 5000 ft long main truss structure consists of ten spans, ranging from 330' to 528' in length, supported on cellular reinforced con­crete pier structures. Foundation systems across the waterway, consist of cellular reinforced concrete footings, supported by groups of 6' diameter, concrete filled, steel caissons, resting on 5' deep rock sockets, at depths of 50' to 150' below the water level. Seismic evaluation of the existing foundation systems accounted for spatially varying ground motion along the length of the structure, variability of foundation material strength (i.e. at bed-rock), variation and effects of scour depth on the performance of the foundations, and dy­namic soil-structure interaction. Performance of caissons beyond their elastic strength, as well as their effects on the behavior of the foundations and substructures were evaluated and considered in establishing foundation vulnerabilities. Several retrofit strategies were considered leading to a final retrofit strategy to strengthen end connections of existing caissons, as well addition of new caissons to provide adequate lateral force resistance for the foundations. Final design package includes specifications as well as construction methods and requirements for existing and new caissons, under traffic, and pile load testing procedures for design loads of up to 12500 kips per caisson.

Jan 1, 1998

In the plumbing of vertical shafts the methods employed and equipment used, are generally made to best suit existing conditions. Undoubtedly, there is no method that can be called standard or that can be used with equal ease and success on all shafts. At the Mount Isa Mines Limited property in Northern Queensland, Australia, local conditions have presented no major difficulties to be overcome in shaft plumbing work. In fact, compared to those at many shafts, the problem has been rather simple. There are three vertical shafts connecting main mine workings, with the greatest plumbing depth for any single lift, 350 ft.Other conditions pertaining to plumbing work have been generally normal.The method we have employed is, in principle, similar to the Weisbach orientation method with a variation that does not necessitate damping of the wires to bring them to rest. Although conditions encountered have not been such that damping the wires would have been inconvenient, we feel we have saved much time and eliminated unnecessary...

Jan 1, 1940

The use of comparative sampling methods during the evaluation of the tin-copper deposits at Cleveland mine yielded closely checking average results from groove, channel, AXT split diamond drill core, and bulk sampling for both tin and copper content of the ore.The weighted mean tin and copper grades and values for the groove, channel, and split core samples showed small percentage differences from bulk sample results, and the F-ratio test for single population origin of the four types of samples was accepted at the 99· 5 per cent level of confidence.These results indicate that grade estimates based on the assays from AXT split diamond drill core and/or groove samples would be reliable within practical limits.

Jan 1, 1968

By Tapio Leskinen

"In the 1960’s, when large flotation machines appeared on the market, this was a part of a world-wide trend towards the use of ever larger machine units.One factor that has played a decisive part in this development is the increased of the amounts of ore that have to be handled as the exploitation of successively poorer ores becomes necessary. The advancing application of instrumentation and automation has worked in the same direction.In 1970, a working group was set up within Outokumpu Oy, for the purpose of flotation machine development. The principal task of this group was to be the design and development of- a new type of rotor of increased efficiency, especially for the dispersion of large amounts of air- a mechanical-pneumatic flotation machine of substantially larger size that existing plant.This development project required an extensive program of theoretical investigation and experimental studies at several concentration plants of the company.The commonest flotation machine presently used in the concentration plants of Outokumpu Oy is the VK-3. It is of the mechanical-pneumatic type, and the volume of its cell tanks is 2.5 m3 per shaft. This machine was developed within the company, and its first development phase i s represented by the OKKO 3, built for the Kotalahti concentrator in 1959. It was, in its time, comparable in volume to the largest machines that were then in use anywhere in the world."

Jan 1, 1976

By Patrick M. - Langevin

THIS TALK IS ABOUT : How the DBL mining camp deposits have been found and what is done to find the next one PLAN: Overview of the geological context Historical exploration perspective Deposits geology and key features Conclusion

May 1, 2006

"The application of telerobotics to mining is currently being introduced into production systems around the world. Mining companies in Canada, Sweden, South Africa, and Australia have tended to lead the international charge to this form of technology for mining. While this introduction is taking place, a few basic questions have yet to be answered. How many machines can a single operator run? How many types of machines can a single operator run?A Canadian Research Chair in Robotics and Mine Automation has been established at Laurentian University to investigate these questions and many more through a series of experiments in a telerobotics laboratory that connects Laurentian teleoperation workstations to model mining machines at Cambrian College’s eDome. The laboratory supports many experiments allowing researchers to physically run multiple robot scenarios differing the numbers and types of machines at one quarter scale. Further experiments are being designed to investigate the potential for managing time delays in telerobotics. This paper describes the laboratory, experiments, and some preliminary results."

Jan 1, 2005

By S. D. Hill

To help insure the continued viability of the minerals and materials sector of the U.S. economy, the Bureau of Mines is conducting research and disseminating technology that will result in more efficient minerals extraction. As part of this effort, a process is being investigated that involves an aqueous chlorine-oxygen leaching procedure to treat complex sulfide concentrates to produce ZnCl2. Subsequent fused-salt electrolysis of the ZnCI2 produces high-purity zinc metal. Previous reports described preliminary, small-scale research on the chlorine-oxygen leaching system and fused-salt electrolysis of ZnCl2. This report discusses the details of design, construction, and longterm, continuous operation of both monopolar and bipolar fused-salt cells. The effects of temperature, electrode gap, current density, electrolyte composition, and electrode configuration on current efficiency and energy consumption were determined for a ZnCl2-KC1-NaCl electrolyte system. Zinc metal was produced at the rate of about 50 lb/day in a monopolar cell which was operated continuously for 60 days with current efficiencies from 85.8 to 98.6 pct and an average power consumption of 2.1 kwhr/lb. Bipolar cells with several different electrode configurations were operated for 90 days. A current efficiency of about 70 pct and power consumption of about 1.7 kwhr/lb of zinc were achieved using a three-electrode-pair, bipolar assembly with a chlorine gas lift pump to circulate electrolyte.

Jan 1, 1981

By Blott S. F

The smelting plant and equipment at Mount Isa, as originally designed and built, was described by J. M. Callow (1) *.F. A. Forward (2) described alterations and additions to the plant and discussed the metallurgy of mixed carbonate-sulphide concentrates at Mount Isa, prior to 1933, in the Proceedings of this Institute.In 1933, A. F. McAskill (3) gave full mechanical details of the plant in a paper presented to the Institution of Engineers, Aust.FLOW SHEETSFig. No. 1 represents the present general flow sheet. Forward's (2) flow sheet is reproduced here as Fig. lA, and will serve for comparison in depicting subsequent deletions from, and alterations and additions to, the plant.Fig. No. 2 presents the daily tonnage flow sheet of 1939 practice.ALTERATIONS SINCE 1933General. Many changes in metallurgy and operation have taken place, particularly subsequent to March, 1935, when the treatment of a mixture of carbonate and sulphide ores was discontinued and the mill commenced operating on all-sulphide ore. This alteration brought about the elimination of gravity concentration-Jigs and Tables and resulted in the production of all-floatation concentrates of a very fine sizing. Refer Table No. 2, page?) Radical changes in the analyses and physical nature of concentrates also followed (see Table Nos. 1 & 2, page ?) and, similarly, radical changes in the smelting plant have been slowly brought about.

Jan 1, 1939

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004

By C. O’Hara, S. Roy, K. Swedburg, J. Katchen

"New Gold Inc.’s New Afton concentrator commenced operation in June 2012, producing a copper-gold-silver concentrate. During the first two years of operation, various optimization efforts have improved mill throughput, recoveries and concentrate grade. Daily mill throughput has increased 20% above the design rate. This was achieved through more consistent instantaneous feed rate and size distribution from the mine reclaim stockpile, higher pebble crusher reliability, changes to the SAG and ball mill grinding media sizes, larger SAG grate openings, reduced SAG discharge screen-deck aperture size and an increase in the maximum ball mill power draw limit. Metal recoveries at New Afton are primarily limited by liberation in the coarser size fractions; therefore, improving the grind size at a given mill throughput has been the main means of improving recovery. The average rougher flotation feed F80 size was reduced from 175µm in Q1 2013 to 165µm in Q1 2014, while the average operating mill throughput increased by 25%. Other flotation circuit changes focusing on recovery improvement include the addition of froth crowders to the rougher cells and the use of a stronger frother. The average concentrate grade increased from 22% Cu in Q1 2013 to 25% Cu in Q1 2014. This was achieved by redirecting the flash flotation concentrate stream to the regrind circuit and by the addition of lime to the cleaner circuit.This paper describes the above improvements made at the New Afton mill. The paper describes the objectives, timing and end result of each area of improvement.IntroductionThe New Afton Mine is situated approximately 10km west of Kamloops, British Columbia, 340km north-east of Vancouver. The mine has a moderate climate, access to transportation and electrical infrastructure, nearby fresh water supply, and close proximity to industrial and mining service businesses. The population of Kamloops is around 90,000 with most mine employees living in or around the city."

Jan 1, 2015

By S Telford, J Weir

Heathgate Resources Pty Ltd (Heathgate) operates the Beverley Uranium Mine in South Australia, located on the plains between the northern Flinders Ranges and Lake Frome some 600 km north of the state capital Adelaide. The uranium orebody exists in permeable sands within the confined, highly saline Beverley aquifer, approximately 125 m below the ground surface and the uranium is mined using in situ recovery (ISR) technology. The Beverley mine is a highly technologically advanced ISR mine and is operated in accordance with stringent safety and environmental standards. The mine is currently licensed to export 1500 t of uranium oxide (U3O8) per annum. This paper outlines the fundamental differences between ISR operations and the more traditional uranium production methods, such as agitation leaching and heap leaching, where the ore is removed from the deposit, stockpiled, crushed, milled and leached on the surface. Solids tailings from either the mill or the heap are finally deposited in a tailing storage facility. ISR mining differs from conventional mining because the ore remains in place underground (in situ) and the groundwater contained in the ore-bearing aquifer is utilised as the mining fluid. This is achieved by drilling into the deposit and installing wells for extracting and re-injecting the groundwater which is fortified with chemicals. The fortified groundwater (ie mining fluid) flows through the permeable sands containing the orebody, dissolving the uranium. The pregnant mining fluid is then collected and transferred to the recovery plant where the uranium is captured (on ion exchange (IX) resin in the case of Beverley). The barren mining fluid is then re-fortified and recycled to the wellfields. Once mining is completed in a wellfield, the surface infrastructure is relocated to a new wellfield, and the mined-out wellfield is rehabilitated to its original surface condition. A comparison of 'standard' hydrometallurgical plants, heap leach and ISR shows a number of key differences, such as the rate of leaching, the level of control available to the operators, and the type of contact/reaction that occurs. While limited in its applications, ISR mining has proven successful at Beverley and provides another mining and processing method for the production of uranium.

Jan 1, 2008

By M Olsen, L van den Berg

Bowen Basin coalmines suffer from hot and humid ambient conditions during the summer period. The ambient conditions combined with high VRTs, increasing depth of working and significant equipment heat loads results in heat issues underground. Coalmines operate under heat stress management plans as required by legislation with associated trigger action response plans (TARPs). Some mines also employ refrigeration as part of their heat management strategy.A recent case study was conducted on a mine producing about 4.5 Mt/a from their longwall and experiences summer surface ambient temperatures of about 23.5ºCwb. The expected virgin rock temperature is 46ºC at 300 m depth. The mine currently introduces a modest amount of surface cooling at the portal using ‘off-the-shelf’ air conditioning units. This system does not effectively manage face temperature primarily due to positional inefficiency.Underground conditions remain hot in summer and work is typically undertaken in accordance with the Heat TARP. This has a direct impact on the productivity of crews, worker comfort and also negatively impacts the workforce morale. The mine commissioned a study to determine a refrigeration strategy aimed at maintaining underground conditions below TARP levels 90 per cent of the time.The ventilation network model was calibrated against actual temperature data to simulate the heat loads including longwall, conveyor system, strata and auxiliary diesel fleet. This model was then used to determine the cooling requirements for bulk surface cooling, bulk underground cooling, surface district cooling and underground district cooling strategies.These estimates were used to undertake a total owning cost trade-off for the different strategies. The study concluded that a chilled air shaft has the lowest technical risk but the highest total owning cost due to shaft development needs. Introducing chilled water to an underground cooler via boreholes offered the lowest total owning cost and was therefore recommended.CITATION:van den Berg, L and Olsen, M, 2017. Heat load assessment and mine cooling strategies for a longwall coalmine, in Proceedings Australian Mine Vent Conference 2017, pp 231–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By A McDowell

Pound Road Quarry is an alluvial gravel quarry owned and operated by Fulton Hogan Ltd. for the supply of aggregate in Canterbury, and is the largest quarry in the South Island in terms of production. It has evolved from three separate quarries, as a result of which extraction has occurred sporadically in a number of areas. Due to this factor, and the need to manage environmental impacts, a detailed quarry management plan was completed in 1995 which formed the basis for implementation of a certified environmental management system.   In December 1997, the quarry was the first in New Zealand to achieve ISO 14001 (TELARC) accreditation for implementation of an environmental management system. The main potential environmental impacts arising from the quarry operation include dust, noise and groundwater contamination, and visual landscape effects associated with gravel extraction, the mitigation of which is achieved by means of æbest practiceÆ methods. All quarry operations are controlled in terms of the environmental management system by means of regular (monthly and yearly) environmental reviews, appropriate auditing of environmental documents, and monitoring of environmental targets in accordance with consent and statutory requirements.

Jan 1, 1998

By M. M. K. McCrank

"PRACTICAL SAMPLING TECHNIQUESIt is important to achieve reliability when sampling heterogeneous materials where there is a difference in composition, and non random distribution of the constituent particles. Throughout the design, construction and installation of sampling systems it must be borne in mind that the sampling point must be capable of:-allowing each particle in the stream an equal opportunity to be sampled.-accepting and collecting as large a volume or mass of material as necessary to satisfy the requirements of particle counting statistics.-establishing a sampling plan so that the sample is representative of the whole to a defined standard of accuracy.Design ConsiderationsFactors that may influence the design of the sample point include:-the mass, or volume flow rate of the material being sampled-the size and shape of the material or flowing stream-the physical condition of the material being sampled (i.e. temperature, wetness, size consist, density).-the chemical composition of the material being sampled -the location of the sample point and the space available for installation, extraction, reduction where necessary, secondary sampling, and return of the sample rejects downstream.-whether the process to be sampled is in an existing plant or one yet to be designed and built.-ease of access for servicing and maintaining the equipment.-whether the sampled material must be collected continuously or intermittently.-whether an existing sampling method is likely to be adequate or whether a new technique has to be developed."

Jan 1, 1989

By J W. Hedenquist

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Epithermal deposits (Au or Ag dominant, ± base metals) form within ~1 km of the surface in volcanic belts, both arcs and rifts, with the different tectonic settings reflected in distinctly different characteristics. Within arcs, deposits are typically intrusion centred and commonly associated with hypogene advanced argillic alteration, both in lithocaps and as halos to shallow or proximal portions of some veins; such alteration is coupled with processes that form porphyry Cu-Au deposits at depths of ~1–3 km. Introduction of metals is related to the subsequent phyllic-stage overprint; if this fluid rises to the level of the lithocap or into epithermal veins, Au mineralisation with Cu or Ag may occur, associated with sulfate minerals or muscovite. By contrast, Au-rich (both low Ag:Au ratio and bonanza grade) colloform quartz veins form at shallow depths in volcanic rifts, typically within a few hundred metres of the surface, with clay halos and topped by silica sinter if the palaeosurface is preserved. The geologic variability in volcanic belts, including host rocks, structures and hydraulic gradients, means that many epithermal deposits vary from the end-member features of the principal styles. Effective exploration requires familiarity with end-member styles as well as potential variations, plus the mineralogical indicators of palaeotemperature (eg evidence for erosion depth, fluid flow channels). This knowledge helps the geologist in the field to imagine what might be buried and where, and how to best test the target with drilling.CITATION:Hedenquist, J W, 2015. Recent developments in understanding of and exploration for epithermal deposits in volcanic arcs , in Proceedings PACRIM 2015 Congress, pp 11–16 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By W. J. Boone

Experimental determinations were made of vapor-liquid equilibria data for a helium-nitrogen-methane system. A mixture composition was chosen to approximate the crude helium to be produced Or conservation that will eventually be further refined to obtain pure helium. Although there are publications of studies of the vapor-liquid equilibria of helium-nitrogen, helium-methane, and nitrogen-methane binary systems, there is little indication of work done on the ternary system of helium-nitrogen-methane. The experimental data presented in this report supplement the information available for the binary systems. The equilibrium vapor-liquid data and equilibrium vaporization coefficients are presented in tabular form. Graphs are employed to show an extensive amount of the data.

Jan 1, 1963

By Emad W. Shublaq

Contractual site plans are implemented for executing pile foundations (5 x 5) at segmental concrete bridge. Project schedule demands have forced the contractor to find out the most economical procedure in achieving the goal. This paper presents a site management technique which is applied by the Contractor. This was found to be fruitful and as much as 60% saving was gained.

Jan 1, 1992

By B Hiebl, J Martens, L Petzold

A research team at the Iron and Steelmaking department at Primetals Technologies has established new upgrading measures for improving the efficiency of the beneficiation process in ironmaking plants, relying largely on pre-existing equipment. After the upgrade, the iron content in the final iron ore concentrate was shown to be significantly higher. Remarkably, the costs for employing the respective measures are surprisingly low.This case study is based on a Kazakh iron and steel producer, whose beneficiation process is currently generating a magnetite concentrate with a final iron content of 65.65 per cent. The study shows that the implementation of Primetals Technologies’ intelligent modification measures to the current beneficiation process, the realisation of more effective dewatering, and the utilisation of an innovative binder lead to an increased iron content in the resulting pellets, reaching a concentration of 69.17 per cent (iron ore concentrate) and 66.5 per cent (pellets).The current operation consists of three closed circuit grinding stages, four stages of low intensity magnetic separation, vacuum disc filters and straight-grate pelletising. By dividing the slurry after the second stage of grinding and the third stage of low intensity magnetic separation, it is possible to divert the more iron-rich fines before they would enter the third grinding stage and the fourth stage of magnetic separation. This then reduces the load on the existing third stage ball mill. Afterwards, the ground material is treated in an additional low intensity magnetic separator and mixed with the previously diverted fraction of the fines. An improved filtration procedure, combined with the application of a highly sophisticated binder, further reduces the amount of additives needed, so that a genuine direct reduced (DR)-grade iron concentrate is produced as a result.All laboratory, pilot and pelletising test work was executed at Primetals Technologies’ laboratories in Austria.CITATION:Martens, J, Petzold, L and Hiebl, B, 2017. Enabling iron ore concentrate for the production of direct reduced iron with pre-existing beneficiation lines, in Proceedings Iron Ore 2017, pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The clay slime generatea in many sand washing operations is usually very difficult to de-water. Treatment of these slimes is often limited by economic considerations and the properties of the solids to a gravity-driven process. The moisture characteristics of kaolinitic slimes from two different sand washing operations were measured.From these curves, equilibrium moisture contents for sedimentation and for drainage were calculated using the methods of soil physics. The validity of these calculations were confirmed by column experiments.The results show that the increased de-watering to be gained by drainage, as compared with sedimentation, is significant. Furthermore, observed rates of outflow indicate that water can be removed considerably morerapidly when drainage is possible.The practical application of these results to the dewatering of clay slimes is discussed.

Jan 1, 1978