Search Documents

By John T. Metcalf

The assembly procedures for nine different wire rope terminations used in the mining industry are presented in a format and manner to facilitate training and to provide points where inspection of the termination should be performed. The nine terminations addressed are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Sleeve & Thimble, Thimble Splice with Four Tucks, U-Bolt Clip & Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The manual was prepared to be used primarily for field type mining operations or training where high capacity machinery is quite limited. It is nut the intent of this manual to suggest that the procedures presented are those to be used by manufacturers or other commercial enterprizes. A different set of procedures may be more appropriate where ideal space and equipment resources are available. The assembly procedures were derived from standard industrial practice, manufacturer's recommendations, and the open literature on the subject. These same procedures were used to prapare test specimens for an extensive series of pull and axial fatigue tests. The results of these tests indicate that these procedures are satisfactory in all respects. This manual is to be used as part of a complete training program. Although a brief glossary is included, there has been no attempt to make this a primer on wire rope. The selection of wire rope termination hardware, like the selection of the wire rope, is a subject not covered by this manual. The reader is cautioned that there are various sources for such hardware and this selection must be done carefully.

Jan 1, 1978

By K. E. Robinson

Appendix A is an abridged extract of the report prepared by the Geotechnical and Structural Engineering Society of Idaho, and presents the results of their one-year study to evaluate the feasibility of disposing mill tailings by landfill construction. Appendix B describes the field and laboratory testing program completed by RDM to assess the effectiveness of a soil (slimes) liner as a means of seepage control to reduce the introduction of contaminants into the local ground water regime. Appendix C presents a summary of a thesis by Lawrence Martin on the analysis of the acid production potential of mill tailings, and the results of geotechnical testing of mill tailings completed by ROM. Appendix D describes potential landfill sites identified within the study area, the development of these sites to meet the present needs of the mining industry and the future requirements of the community is described. Appendix E summarizes the main legislation impacting on tailings disposal. Appendix F discusses the environmental and socio-economic factors that should be considered.

Jan 1, 1981

By S. Makni, R. E. McIvor

Grate discharges historically outnumbered the overflow type of industrial wet ball mills. However, overflow discharge mills now strongly dominate. In order to understand their comparative advantages and disadvantages, Corem carried out a broad review of this topic. Where the data made it possible, the Functional Performance Equation was used to separate circuit classification from mill grinding effects. Batch tests were conducted in a torque-metered mill at different slurry levels. This paper presents the outcome of these investigations, which is a very strong case for the industry to once again consider grate discharges.

Feb 1, 2023

By E. C. Hoeman, W. C. Stoecker, R. C. Redfield

"INTRODUCTION Industrial sands, characterized by specific physical and chemical proportion, are,essential new materials for the manufacture of glass, sodium siliante and other products. Sands of suitable characteristics are used extensively for molds and cores in the casting of metals as a granular medium in municipal water filters, as abrasives, as traction sand to prevent the slipping of driving wheels of self-propelled vehicles on trucks and in various ceramic and other structural forms. In addition to the use of common silicon sands in concrete, cement, and mortar, special sands find use in sand-lime brick oxychloride cement, and flooring, for coating prepared roofing, and for placing ware in saggers although sand for sandpaper has been mostly displaced by other harder mineral or synthetic grains, other abrasive uses are numerous and include sandblasting stone sawing, glass burnishing and finishing."

Oct 1, 1945

By R. Lahtinen, M. Tiainen, R. Salminen

The application of similarity analysis derived from regional geochemical mapping data to the location of Ni-bearing intrusions was tested in southwest Finland, where a well-known nickel belt is situated. Samples of till from the vicinity of the Vammala and Kylmakoski Ni-Cu deposits, which were collected independently of the Geological Survey of Finland's regional geochemical mapping programme, were used to provide geochemical modelling data. The data consist of the aqua regia-leachable concentrations of 20 elements from the less than 0.06-mm fraction of glacial till. The variables used in the similarity analysis were selected on the basis of a factor analysis in which the method of oblique rotation was used. A hierarchical clustering of the modelling samples produced two main groups. The first group was described as the "nickel deposit environment model" and the second as the "nickel deposit location model". The data for the standardised variables were compared sample by sample with the model data by similarity analysis using the Simana program with a cos theta measure of pattern similarity. The nickel deposit environment model delineated the known Ni belt and indicated an extension to the east. The nickel deposit location model identified target areas of reasonable size with the greatest potential for Ni ores within the nickel belt

Dec 1, 1991

By Michael S. Wieland

"Toxic fumes cause fatal andnonfatal incidents in underground mining, where the working environment tends to trap the fumes, hindering the restoration of non-harmful conditions. Workers can underestimate the residual fume toxicity and return to the work site too quickly. The toxic fumes from charge explosions depend upon a number things: formulation ingredients, mixture uniformity, water resistance, hole contaminates, rock hardness, and dust interactions. Transitory hole-to-hole waves can cause partial desensitization, ruin the reaction kinetics, and worsen the fume toxicity.Traditionally the toxic fume hazard for a candidate explosive is resolved from a requisite tally of fume components. The resolution starts with the fume spectrum, a tabulation of specie concentrations, transformed to standard reference conditions and readjusted to remove the air dilution. The resultant influence, which is referred to as relative fume toxicity RFT, is deduced by a formula rule with some chosen constants and the requisite concentrations. The RFT result is normally compared to an RFT criterion that represents the worst-case (maximum) tolerable fume toxicity, as stipulated by regulations or otherwise."

Jan 1, 1997

By B. van Beek, T. Goff, P. Gebski, P. Szyplinski, W. L. Ying

"Monitoring the refractory lining integrity is essential to assure the safety of the operators and to determine the remaining campaign life of a furnace. Early detection of refractory lining degradation is essential to avoid sudden furnace failures and prevent unscheduled shutdowns. In the mid-1990s a stress wave propagation technique was developed and since then it has been utilized by Hatch Non-Destructive Testing (NDT) Group to evaluate furnace linings. For the last 17 years the AU-E technique evolved in terms of hardware, software and signal acquisition and interpretation. Most importantly, based on more than a decade of commercial applications, an extensive database of various failure modes, refractory deterioration trends and material properties has been created. This knowledge base is an integral part of AU-E which progressed from a NDT technique towards a comprehensive approach for furnace condition monitoring. All of the improvements introduced over the last several years have greatly improved the accuracy of the measurements. The data analysis process has also become more time efficient making the critical results available to the furnace operators in a more timely manner. Today the AU-E technology is used on a variety of process vessels in non-ferrous, glass, chemical and iron and steel industries.In this paper we are reviewing the available techniques for furnace refractory lining measurement and discussing the pros and cons of each method. The need for continuous improvement and development of new techniques for refractory monitoring is also emphasized. Finally, we are presenting a number of case studies and comparisons between the physical verifications and the AU-E measurements."

Jan 1, 2015

By George P. Jr Schivley

Looking at the process of drilling rock from the standpoint of the power required, yields an equation that relates Force-on-the-Bit; Torque, to rotate the bit; and bit Angular Speed to the Penetration Rate of the bit; the Area of the hole being drilled and the Specific Fracture Energy of the rock. Specific Fracture Energy and the Compressive Strength of the rock are related.

Jan 1, 1994

By W. P. Yant

A previous report of the Bureau of Mines dealt with the toxicity of dichlorodifluoromethane5, a new refrigerant that has a remarkably low toxicity. Continued research by the Prigidaire Corporation6 and toxicological experiments performed in the Laboratory of Applied Physiology of the University of Cincinnati7 revealed another organic fluoride, dichlorotetrafluoroethane, whose toxicity also appeared to be of a very low order and whose physical-and chemical properties make it suitable for refrigeration purposes. In addition to low toxicity, safety in its use is further enhanced by its physical properties, which permit the design of equipment that operates at comparatively low pressures and hence mitigates the dangers and problems of leakage. The investigation described in this report was performed by the Bureau of Mines at the request and with the cooperation of the Frigidaire Corporation.

Jan 1, 1932

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

By R. Hipsley, D. Arbonies, P. Dobak

South Arturo is a “Carlin-type”, breccia-hosted, oxide gold deposit located at the north end of the Carlin Trend. The discovery hole was drilled in July 2005 from mine dumps 1,000 feet south of the Dee open pit. Discovery hole (BD-72) encountered a cumulative 245 feet @ 0.056 opt Au beneath 850 feet of post mineral Tertiary Carlin Formation. Oxidation extends to depths greater than 2,000 feet in the deposit area. The deposit is presently in definition drilling stage with approximately 190,000 feet of drilling completed to date. A resource estimate is in progress. This paper will focus on the discovery and descriptive characteristics of the mineralization.

Jan 1, 2007

By Steve Kral

U.S. mines are among the most efficient, productive and safest in the world. Much of that efficiency is due to the high-technology equipment and processes available to the industry. The U.S. mining industry can produce more material now with fewer people than it could a few decades ago. And that material can be produced more safely. However, the workforce is growing older and fewer young people are filling the holes created by retirements. Even though mining is one of the highest paid occupations in the United States, young people believe they can find jobs that pay almost as well without the risks and the often remote locations associated with mines.

Jan 1, 2002

By C. H. Kats, E. G. Meiter, J. J. Bloomfield

"INTRODUCTION.Street manholes for underground power and signal circuits, and for sewers vary in size from small openings that a workman can enter, to large central vaults. As the gas hazards in manholes are similar to those in mines, the mine safety committee of the Bureau of Mines was asked whether the miners' flame safety lamp is a practicable device for indicating inflammable gases in manholes.The coal miner detects firedamp (methane or CH4) with his flame safety lamp by observing the luminous can or the increased length of flame that appears when 1.5 per cent or more of the combustible gas is present. The lamp flame also warns him of lack of oxygen by going out when the oxygen becomes less than 16 to L7 per cent. A tentative rule regarding the proposed use of safety lamps at manholes has been suggested previously as follows: ""Testing for gas: Do not enter manholes until you have .assured yourself that the manholes are free from dangerous gases, by testing with an approved safety lamp, by ventilation, or by other adequate methods."" The Bureau's committee recommended that miners' flame safety lamps are not suitable,testing in manholes because hydrogen gas may be formed therein. The flame safety lamps approved by the Bureau of Mines for use in aseous mines are safe in presence of methane and while not tested against the members of the paraffin hydrocarbon series (CnH2n+2) higher than methane they been have been used therein; the lamps should not be used in hydrogen or acetylene they can initiate explosions in presence of these gases."

Oct 1, 1925

By Denis Labrie

Le minage en profondeur sous contrainte modérée à élevée présente de nombreux défis aux opérateurs et aux ingénieurs de mine notamment au niveau du contrôle de terrain et de l?environnement minier souterrain, pour assurer la sécurité des travailleurs sous terre et la continuité du cycle d?opération. Des conditions de contrainte élevée signifient une pression accrue au front de taille et sur les structures minières tels les piliers de mine et les fins de zone, un risque de rupture violente ou de coup de toit plus élevé, des zones de rupture plus grandes au pourtour des excavations, des charges accrues sur le support de terrain, etc. Le présent article fournit un aperçu du travail fait à l?intérieur du Programme de Contrôle de terrain de CANMET au cours des sept (7) dernières années, entre 1995 et 2001, pour comprendre et suivre l?évolution des niveaux de contrainte à l?intérieur des structures minières. Les propriétés déterminées en laboratoire sur des échantillons rocheux et les prévisions effectuées au moment de la conception sont comparées avec les observations effectuées en chantier à la paroi des excavations et à l?intérieur de la masse rocheuse. La plupart des cas discutés ici montrent une corrélation satisfaisante entre les observations effectuées en chantier d?une part, et les résultats d?essai obtenus en laboratoire et les calculs réalisés lors de la conception d?autre part. Ces observations peuvent donc être considérées comme des moyens relativement sûrs pour vérifier et suivre l?évolution des niveaux de contrainte présents à l?intérieur des structures minières.

May 1, 2002

IN this paper it is proposed to present certain features of operating practice at the Port Pirie works of The Broken Hill Associated Smelters Proprietary Limited, in the smelting in a blast furnace of lead ores carrying a high concentration of zinc.The subject matter selected for presentation is:(i) The effect of zinc on lead blast-furnace operations, together with an outline of the methods adopted in actual practice in dealing with the zinc problem.(2) Development of the height of tuyere above the bottom of the jacket, and the extension of the tapping interval and the combined effect of both factors upon the lead content of blast furnace slag.It will later be seen that one phase of the investigation carried out in connection with the effect of zinc on blast-furnace operations was largely responsible for the decision to increase to a marked degree the height of the tuyere above the bottom of the jacket.Due to this interdependence, it has been considered advisable to deal with the two features above mentioned.The high concentration of zinc in the lead-bearing materials smelted at Port Pirie has brought with it those troubles which are associated with zinc in the smelting operation.In the early stages of the history of The Broken Hill Associated Smelters Pty. Ltd. the trend towards increasing cost for labour, fuel, and stores, etc., rendered it necessary to increase the lead content of the charge, and reduce to a minimum the quantity of barren flux used.

Jan 1, 1931

By Reinhard Gnilsen

Soil Nail walls, like any other structure, must meet high standards of design to be acceptable to the public and owners. On the other hand, the concept of soil nailing trails behind other structures in terms of defined design criteria that are commonly acknowledged. This is not to say that soil nail walls need to be less safe or less conservative than alternative more conventional concepts. Instead, the lack of established design criteria and design methodology entails that rules of thumb from past experience, overly simplified calculation assumptions, and the engineers&apos; common sense judgement must substitute for a complex analysis of true stability and wall performance. Those "design approaches" must be conservative to ensure an adequate structure. Also, soil nailing may not be perceived prudent where site conditions are considered beyond past experience. For instance, site conditions may be perceived out-side the scope of soil nailing applicability where walls are very high, soil parameters variable or low, or nearby buildings close to the wall edge. The latter relates in particular to deep

Jan 1, 1988

By Holt L. Farley

This report describes the development of an electronic system which detects unsafe slack and overload conditions in underground mine hoist ropes. The Slack and Overload Rope Protection System (SORPS) includes a fail-safe load cell inserted between the rope and the conveyance, and an accelerometer mounted on the conveyance. Signals from these transducers are telemetered via a radio link to the hoist control room, where they are combined with drum speed and chair status in a microprocessor-based decision and display unit. Abnormally high external force levels are detected as discrepancies between rope tension and cage acceleration; conveyance weight is inferred continuously. Hazardous conditions are displayed to the hoist operator, along with general hoist status. The system has been tested in a working mine for approximately two years. The report contains specifications, design data and field test experience generated under the SORPS program. It also includes information on dynamic modeling, vibration environment, the status of existing slack detection systems, and applicable control strategies.

Jan 1, 1983

By M. I. Mthenjane

"BackgroundThe paper discusses post-mining land use however, the essence of the topic is the emotional motivation behind the decisions related to mining investment and development. Therefore this is not a typical SAIMM technical paper about the science and techniques of post-mining land use. There are already numerous papers written and conferences held on this aspect of post-mine land use; the science is well understood, but the evidence of the practical application of the (environmental, social, and economic) science is sparse. At a recent conference held in November 2017 on the theme of ‘Science, Business, Society Dialogue – linking science, society, business and policy for the sustainable use of abandoned mines in the SADC region’, it was demonstrated through the delivery of several papers on the possible viable options of post-mine land use. The conference was structured in nine sessions, covering the following relevant topics:? Sessions 1 and 2: Nature and magnitude of the problem: raising awareness? Sessions 3 and 4: International experiences in remediation: case studies? Sessions 5, 6 and, 7: Technological solutions: converting liabilities into assets? Session 8: Implementing solutions: social and legal aspects? Session 9: Wrap up, lessons learned: conference resolution.Summaries of the key outcomes of the sessions are available for reference.The aim of this paper, accompanied by the video speech, is to provide a visualization of the possibilities of post-mine land use. Mining contributes approximately 7% to South Africa’s GDP - this is the lowest it has ever been and is attributable to both a diversifying economy and to poor mining and investment policy which has resulted in reduced investment in the sector. The objective of the paper is to highlight the opportunities, for succeeding and diversifying economic activity following mining and mineral extraction which can continue to sustain the livelihoods and wellbeing of communities and societies beyond mining.During mining, very few alternative and local economies develop. Dependence on mining and its value chain prevails until mining ceases. This idea is conveyed in Figures 1a and b."

Jul 1, 2019

By K. Coleman, C. Visser, N. Selby, X. W. Pan, T. Letwaba

A prototype weightometer soft sensor is under development at DebTech, De Beers in partnership with Venetia Mine. Its main function consists of an online data source; data validation; dynamic weightometer models; online detection of weightometer failure; alarming and replacing a weightometer when it fails. 31 dynamic models have been developed. All models with R2>= 85%are accepted as good models and they generally have satisfactory results with a daily error of less than 8% within 90% confidence level. By using those models, a set of soft sensors can be set up to cover all weightometers in the entire processes starting from primary crushing to the stock piles of dense medium separation (DMS). Some practical issues and concerns on model development are discussed, including data collection, data analysis, data pre-processing, variable selection, time delay, model training and model validation. When deploying the weightometer soft sensor system, the potential benefits could include: reduction in plant downtime; reduction in unplanned maintenance and even replacement of non-critical weightometers, particularly where nuclear weightometers are used. Keywords: soft sensor, weightometer, dynamic modelling, neural network modelling

Jan 1, 2003

By L. A. Neumeier

The Bureau of Mines investigated hot-rolling and forging characteristics of experimental ductile iron castings, both sand and permanent-mold, made with charges containing up to 70 pct foundry pig iron and 95 pct steelmaking pig iron. Between 1,550° and 1,950° F, most castings could be rolled to 90-pct reduction or forged to 70-pct reduction without serious cracking. Charge and composition have less bearing on workability than on subsequent properties. Permanent mold castings could be worked as readily as sand castings at 1,750° and 1,950° F. Plasticity improved with temperature. Small billets were also forged cold to 50-pct reduction without cracking. With equivalent nodularity, composition affects properties of wrought materials by altering matrix structure and strength. Properties vary with reduction and improve with increasing working temperature. Rolled material has high strength and anisotropy, and low ductility, particularly in the trans-verse direction. Annealing reduces strength and improves ductility, but anisotropy persists. At 70-pct reduction, impact resistance in the longitudinal direction is about twice that in the transverse. Annealing roughly doubles impact resistance. Deformation enhances damping capacity. The feasibility of die-forging and bar-rolling of ductile iron was evaluated in trial tests conducted under a Bureau contract. Although workability and ductility of ductile iron are inferior to those of steel, more advantage could be taken of ductile iron&apos;s plasticity to work rough shapes to final dimensions.

Jan 1, 1980