Search Documents

By Iain B. Mackenzie

In 1997, a thin layer of Microtherm Microporous Insulation was used to replace fireclay brick behind the magnesia/chrome working lining in #5 refining furnace at BHP?s San Manuel AZ smelter. A 23°C reduction in shell temperature was obtained, together with a large increase in the working capacity of the vessel. There was no sign of metal penetration as a result of the increased insulation. Following these highly favorable results, BHP have introduced this product into all of their refining furnaces.

Jan 1, 1999

By Guiqing Zhang, Liansheng Xiao, Zuoying Cao, Li Zeng

A new process of direct solvent extraction of nickel from sulfuric acid leach solutions of low grade and complicated nickel resources using a novel extractant HBL110 was proposed. The basic performance of new organic system was investigated and the continuous pilot plant and the industrial test were conducted. The results indicated that the extractant of HBL110 can be used to directly extract nickel selectively over iron, aluminum, manganese, magnesium, calcium and chromium from sulfuric acid leach solutions. The loaded organic solution can be easily stripped using dilute H2SO4 solutions. Both kinetics of extraction and stripping of nickel were fast. The continuous pilot plant test with the sulfuric acid leach solution of laterite containing 6.22g/L Ni2+, 14.1g/L Fe3+, 0.73g/L Fe2+, 33.9g/L Mg2+, 1.58g/L Al3+, 0.495g/L Ca2+, 0.97g/L Mn2+ and 0.5g/L Cr3+ as feed in mixer-settlers showed that the process had run stably with 98% recovery of nickel. The concentration of nickel in strip liquors reached as high as 50 g/L while the removals of Fe3+, Fe2+, Mg2+, Al3+, Ca2+, Mn2+ and Cr3+ were 98.5%, 91.5%, 99.95%, 99.8%, 99.1%, 98.6% and 99.5%, respectively. The industrial test with the sulfuric acid leach solution of electroplating sludge containing 11.5g/L Ni2+, 2.68g/L Fe3+, 7.54g/L Cr3+, 0.61g/L Mg2+, 2.09g/L Al3+, 0.68g/L Ca2+, 0.022g/L Mn2+ and 0.154g/L SiO2 as feed in mixer-settlers also showed that the process had operated successfully with 99.5% recovery of nickel. The concentration of nickel in strip liquors reached 42.7 g/L while the removals of Fe3+, Cr3+, Mg2+, Al3+, Ca2+, Mn2+ and SiO2 were 99.2%, 99.77%, 99.73%, 99.56%, 99.57%, 98.51% and 98.75%, respectively. The new process exhibited big advantages of short flow sheet, high recovery of nickel, high removal of impurities, low chemical reagent consumption and low cost. Application of this process in industry is expected to make important impact on the extraction of nickel from sulfuric acid leach solutions and to deliver good environmental and economical benefits.

Jan 1, 2016

By Shaohua Ju

Siderite ore is abundant around the world, due to its inert properties of low grade, mudding when milling and low magnetic, and it is very hard to be beneficiated. Nowadays, decomposition by roasting becomes the main process for utilization of the siderite ore. The methods of energy input for roasting are normally electrical heating, coal or gas combustion. Because traditional roasting methods owns some disadvantiges, such as low energy utilization, high cost and/or large exhaust pollution, only about 10% of the siderite ores in China were used as iron concentrate. In this work, the possibility of roasting siderite ore with microwave energy is studied by both laboratory and pilot experiments. The result of laboratory experiments showed that the optimized condition is roasting for 20 min with a power density of 3 W/g, and the Fe content of the final sample obtained is about 59.12%. The pilot experiments result showed that the decomposition is thoroughly, and the main phases of the roasted material are magnetite and wustite, and the energy consumption of the roasting process is 695.8 KWh/t.

Jan 1, 2014

By Yasuhiro Konishi, Yoshiyuki Noda

"This paper describes a new processing of rare-earth oxide precursor, in which rare-earth carbonate powders are precipitated directly from emulsions of rare-earth loaded carboxylate solutions, using CO2 gas and water. This synthetic route of rare earth carbonate is a combined process of the stripping and precipitation stages in a conventional solvent extraction. Using this technique, lanthanum carbonate and yttrium carbonate were prepared at temperatures of 10 to 80°C and CO2 pressures of 0.1 to 3.0 MPa for 120 min. The rates of carbonate precipitation in a batch autoclave were sensitive to processing parameters such as CO2 pressure, temperature, and organic-phase composition. The particle size distributions of the carbonate powders were markedly dependent on temperature and C02 pressure.IntroductionSolvent extraction is the most appropriate commercial technology for separation and purification of rare earths. In typical commercial processes, the rare earths are stripped from loaded solvent extractants using aqueous solutions of mineral acid. After adjusting the pH of the aqueous strip solution, the rare earths are precipitated as insoluble powders of oxalates or carbonates, from which oxides can be produced by calcination. Such conventional processing can be simplified when the stripping and precipitation stages are combined by emulsifying rare-earth loaded solvent extractant with aqueous oxalic acid solution. It is likely that the single-stage precipitation stripping results in a marked decline in the consumed amounts of precipitating and neutralizing agents, thereby saving on both running and capital costs.Yoon and Doyle1) first demonstrated that oxalate powders of lanthanum and yttrium are directly precipitated from rare-earth loaded carboxylic acid solvent extractant when contacted with aqueous oxalic acid solution at ambient temperature and atmospheric pressure. Yttrium oxalate pow4ers were also prepared by precipitation stripping of di-(2 ethylhexyl) phosphoric acid. (D2EHPA) extractant using oxalic acid-hydrochloric acid solutions. 2) Moreover, neodymium oxalates were directly precipitated from organic solutions of tertiary aliphatic monocarboxylic acid and 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester using aqueous oxalic acid solutions, and powder characteristics of the resulting oxalates were compared with those of powders by the conventional solvent extraction routes. 3 • 4) Recently, attention has been directed towards the influence of processing parameters on the particle size distributions of yttrium oxalate precipitates. 5)"

Jan 1, 2000

By E. V. Redin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Green pellets were processed via a lab tube (chamber) furnace to simulate RHF conditions. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2012

By R. S. Tahautdinov, A. N. Posazhennikov, V. V. Bastrygin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Samples of iron ore and carbon reductant were chemically and physically analyzed. Green pellets were processed via a lab tube furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2011

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Viviane Tavares Moraes

"The development of mobile phone technology has increased the replacement of outdated equipments for more modern models, transforming disposal of such devices into a serious environmental problem. Recycling appears as an attractive alternative to minimize the environmental impact of disposing such large quantities. Recycling can be accomplished by treating the printed circuit boards of used mobile phones by using the same techniques used in ore treatments with hammer mill; magnetic separation, electrostatic separation and grain size range. Before performing the recycling process a PCB characterization was performed to identify the fraction with the higher metals concentration/content. This study demonstrated that the electrostatic separation was not the best metals concentration of PCB aiming the recycling, while the non-magnetic residue had presented a more significant metal concentration. Furthermore, after the magnetic separation was possible to separate the following metals: iron and nickel.IntroductionPortable electronic devices have gained increasing acceptance over the last decades. Mobile phones sales in Brazil, for instance, have reached 104 million in 2007, and 128 million in 2008. It is estimated that, around the world, 100 million mobiles are thrown away every year, either because of loss of functionality or because newer models are launched in the market [1,2, 3]. Printed circuit boards in mobile phones are made of many materials, with approximately 83% in weight being metals and fiber-glass, and the balance being plastics pl. Several metals can be recovered from the electronics waste, such as copper, tin, iron, lead, nickel, titanium, aluminium as well as some precious metals such as gold, silver and palladium [4, 5, 6, 7, 8]. Concurrent with the increasing world demand for copper, there average metal content in ores has been decreasing. Economically interesting copper mines used to have 4% metal content, whereas presently, such content is around 1%, i.e., for every 1 ton of ore extracted, only 10 kg are copper [9, 10]. Approximately 33% of printed circuit boards (PCBs) composition is copper, that is, for every 1 ton of PCBs waste, 330 kg are copper [1]. Research in recycling PCB waste focuses on mechanical, electrometallurgy, pyrometallurgical and hydrometallurgical processes [3, 8]. Collecting and recycling obsoletes electro-electronic equipments is very important these days, in order to, not just preserve the non renewable natural resources but also to keep the environment and the population safe from the pollution caused by the toxic materials and heavy metals present in this kind of waste."

Jan 1, 2011

By Chao Zhang, Jian Guo, Chaoquan Yao, Leige Xia, Xinyu Li, Jianliang Zhang

In this research, analytical reagents were used for the sintering experiments. And the sinters were using X-ray diffraction, scanning electron microscope and mineralogical microscope analysis to study the effect mechanism of manganese on the silico-ferrite of calcium and aluminum (SFCA) bonding phase formation during the sintering process. The results indicated that the increasing content of manganese would greatly reduce the content of SFCA, and promote the formation of calcium aluminum silicate and the amount of pores and cracks. The existence of manganese inhibited the silicon form into the SFCA and a great deal of Fe2O3 was participated in the crystal transition to Fe3O4. When the ratio of the added manganese was less than 3% in the mixing, the calcium ferrite was in substantially interleaving corrosion with hematite and magnetite. Both the porosity and silicate glass phase content were low simultaneously, which contributed to the sintering production.

Jan 1, 2015

By Jewel Gomes

Green rust is an important intermediate in oxidative transformation of Fe(II) phase. This unstable compound contains a mixture of ferrous and ferric hydroxides that belong to a family of minerals known as layered double hydroxides (LDH). Its general formula is [FeII(6-x) FeIIIx (OH)12]x+[Ax/n-*yH2O] x-, where A is an n-valent anion mainly Cl-, CO3-2 and SO4-2, and in which either the bivalent or the trivalent iron can be replaced for other trivalent or bivalent metal ions. It was first identified as corrosion product, later in soils as a product of interactions between microbes and metals in soils. Due to its high reactivity, it is used in the reduction of organic and inorganic compounds, As removal, and the treatment of acid mine drainage. In this paper, we described the method of electrochemical generation of green rust, its characterization by XRD, SEM and FT-IR, and its implications to electrocoagulation.

Jan 1, 2009

By Liu bing-guo, Peng Jin-hui, Guo Sheng-hui, Kong dong-cheng, Hu jin-ming, Zhang Li-bo

The novel technology of calcination to prepare triuranium octaoxide（U3O8）from ammonium uranyl carbonate in microwave fields was investigated on the basis of the temperature rising characteristics of ammonium uranyl carbonate, triuranium octaoxide (U3O8), and their mixture. The result of experiments show that ammonium uranyl carbonate had weak capability to absorb microwave energy, while triuranium octaoxide has the very strong capability to absorb microwave energy and the sample temperature increased rapidly with an increase mixture ratio of triuranium octaoxide. The optimal calcination conditions were as follows: microwave power 700 W, calcination time 10 min and 60 g in this experiments range, respectively. Under these conditions the value of total uranium and 4 U of triuranium octaoxide was 84.28% and 31.02%, respectively. It is feasible to prepare triuranium octaoxide by calcination from ammonium uranyl carbonate, which mixed with small amounts of triuranium octaoxide under microwave fields.

Jan 1, 2015

By Metehan Erdogan, Ishak Karakaya, Fuat Erden, Emre Ergül

"The FFC Cambridge process was suggested as a promising Si production technique for the expanding solar energy industry. Direct electrochemical reduction of bulk SiO2 plates and porous SiO2 pellets in molten CaCl2-NaCl salt mixture were investigated at 750°C by applying 2.8 V potential difference. The produced Si powder was brown and found to be contaminated by the Ni and stainless steel plates used as the cathode contacting materials. The reduction rates of the bulk SiO2 plates and porous SiO2 pellets were compared from variations of current and accumulative electrical charge that passed through the cell during the electrochemical reduction. The amorphous bulk SiO2 plates were reduced slightly faster than porous pellets of crystalline SiO2. The overall reduction potential of SiO2 pellets against the graphite anode at 750°C in molten CaCl2-NaCl salt mixture was determined as 2.3 V by cyclic voltammetry. This potential was supported by calculations.IntroductionMetallurgical grade Si cannot be directly used in electronic industry and some intermediate steps are required to produce industrial solar grade silicon (SOG-Si). A promising alternative solar grade silicon production technique is the FFC Cambridge Process [1]. Production of Si by electrochemical reduction of SiO2 at 850oC in molten CaCl2 electrolyte was first studied by Nohira et.al. [2]. In their study; Si formation was observed on bulk SiO2 cathodes after 1 hour of electrolysis. Complete electrochemical reduction of porous SiO2 pellets was first reported by Jin and his coworkers [3]. The mechanism of electrochemical reduction of SiO2 to Si in molten CaCl2 was explained in another study [4]. Reduction rates of bulk SiO2 and porous SiO2 pellets were also compared previously and it was found that reduction rates for bulk plates were higher [5]. Furthermore, it was reported that mixing Si into porous SiO2 pellet increased the reduction rate [5]. Mo [2, 4-7], Ni [3, 8, 9] or Si [6] were used as cathode contacting materials in various studies. Yasuda et. al. [6] produced Si with 99.80 % purity using Si plates as cathode contacting material to reduce metal contamination."

Jan 1, 2012

By Tugba Basargan Çagatay Morall, Gülhayat Nasun-Saygili

"The aim of this study is to prepare the apatitic material using colemanite mineral (2CaO.3B2O3.5H2O) which was obtained from Eastern Anatolia, Turkey. For this purpose, colemanite mineral was reacted with different phosphate sources, namely, dipotassiumhydrogen phosphate, ammoniumhydrogen phosphate and ortophosphoric acid at various temperatures and time periods. Experiments were run in batch system. The apatitic material was prepared by a wet method and followed by heat treatment at various temperatures. Structure of the samples was analyzed by XRD, FTIR, XRF and SEM. The particle size analysis was also made for the result product. The experiments showed that reaction temperature, contact time and heating temperature are important parameters to transform the colemanite into apatitic structure. Reaction of colemanite with dipotassiumhydrogen phosphate and ammoniumhydrogen phosphate results in amorphous, non-stoichiometric hydroxyapatite type structure, while acid based phosphate source gives brushite and monetite type product before and after heat treatment, respectively.IntroductionBoron which has properties intermediate between metals and non-metals is a member of semiconductor group of elements. Its atom is very small and has three valence electrons. Boron exists in Earth's crust (from 5 mg/kg in basalts to 100 mg/kg in shale) and in the oceans (4.5 mg/l) [1]. Turkey has 60% of world's boron reserves which is mostly in the form of colemanite (2Ca0.3B203.5H20). Colemanite is the most important calcium containing commercial borate mineral with 5 mol of crystal water [2].Calcium phosphate cements are very useful for bone repair applications because of its chemical structure. They are injectable, easy to shape and can be maintained locally. Because of those reasons calcium phosphate cements are very effective to fill bone defects with an irregular shape [3]. Hydroxyapatite (Ca10(PO)6(OHh) is the major component of the bone (70 wt%). However, hydroxyapatite stoichiometry, composition and crystallinity differ in human skeleton system [4, 5].The main objective of the present work was to study the transformation of colemanite to apatitic material using different phosphate solutions at several time spans and temperatures. The experiments were run in a batch system, change in pH and also weight loss were measured after the experiments. Several analysis methods were used to investigate the chemical and structural changes."

Jan 1, 2012

By Robert Fritzsch, Ragnhild E. Aune, Mark William Kennedy, Behzad Mirzaei

"The quantitative particle concentration can give important information about the cleanliness of melts for quality control in primary and secondary production of aluminum. Manual quantification of the particle concentration is normally a time consuming process and human control can bias the acquired images and particle count.The present paper explains the automated image-processing steps for the quantification of SiC-particles, with equivalent diameters from 2 to 25 µm, in solidified A356. A total of 700 micrographs, acquired with a standard white light microscope with 10 x magnification, were analyzed. The applied software (Image Pro-Plus 7.0 from MediaCybemetics®) allows for programming of macros which in tum provides the user with a higher degree of control. The automated results are compared with the results obtained by manually counting the particles in the same micrographs. The impact of the automated results on the estimated filtration efficiency was established to be only -3%.IntroductionInclusions are both indigenous and exogenous particulates that are present in commercial metals such as aluminum. If large individual or large numbers of inclusions are present, they can have a significant negative impact on the appearance, mechanical and chemical behavior of products produced from the metal. Aluminum is known to contain large numbers of inclusions: =50 µm in size, e.g. typically <l ppm by volume or <100,000 inclusions of>20 µm per kg of metal as detectable using a Liquid Metal Cleanliness Analyzer, LiMCA [1]. Depending on the final application of the aluminum, inclusions can render the metal 'not fit for purpose', and result in serious economic consequences to metal producers.It is not surprising that the aluminum industry has developed a number of treatment processes to improve metal cleanliness, given the large number of high value products whose quality can be adversely affected by inclusions. CFFs are the most commonly applied filtration process and have been used to filter >50% of the world production of aluminum since the 1990's [2].Inclusions in aluminum may be particles, bifilms [3] or clusters of: oxides (Al2O3 , SiO2), spinels (MgO· Al2O3), carbides (SiC, Al4C3), nitrides (AlN), borides (TiB2), sulfides, phosphides and intermetallics [ 4]."

Jan 1, 2013

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Lei Zhang, Shining Chen, Lina Wang, Pu Liu, Benquan Fu, Jiannyang Hwang

A three-dimensional (3D) electrode reactor combined with Fenton reagent was used for advanced treatment of coking wastewater from secondary biological treatment. Effects of some key factors on total organic carbon (TOC) removal rate were investigated, and the results were compared with those of the common three-dimensional electrode reactor. Experimental results showed that TOC removal rate could reach 51.7%, when optimal operating conditions were as follows: initial pH value 3.5, H2O2 dosage 17.6mmol/L, reaction time 90min and FeSO4·7H2O dosage 3.5mmol/L. Analytical results from UV absorption spectra indicated that the organic substances in the coking wastewater were well degraded by this system, which provided good experimental basis for the practical application of this process in the treatment of coking wastewater. This can be meaningful for the treatment of other kinds of wastewater.

Jan 1, 2015