Search Documents

By A. Martikainen, H. Dougherty

"At the Kemi Mine, a recent expansion into the Surmaoja orebody required an increase in ventilation capacity. A new ventilation shaft was built with two main fans. The installation is near the entrance gate and only 1.7 kilometres from the nearest permanent dwelling. The main fans were first taken into use as exhaust fans in October 2014. Shortly after the fan installation, comments concerning fan noise were received from the neighbours. The first noise measurements were taken at the main fan installation site by Outokumpu personnel in March 2015. Due to higher than expected recorded values, during late June, 2015, a two-week environmental noise study was planned by the engineers and executed by a consultant specialized in noise measurement. The measurement results were analysed and compared to the requirements of the environmental permit and Outokumpu’s factory standards. While the measured values at the nearest dwelling were within the environmental permit limits, high noise values were recorded at the fan station. A second two-week study will be performed after construction of the main-fan heating station has been completed. Actions taken will depend on the outcome. INTRODUCTION The Kemi Mine is a part of the Outokumpu chain of integrated ferrochrome and stainless steel manufacturing in the Kemi-Tornio region in Finland. The mine itself is a large underground operation with a production capacity of 2.7 million tons of ore per annum. It is also the European Union’s only chrome mine, and at present (2015) the mine extracts 2.4 million tons of chrome ore per year. Safety, cost-effectiveness, and environmental friendliness are hallmarks of the Kemi Mine. Environmental impact produced by the operation of the mine is limited due to the insolubility of the oxide chromium ore, the gravity-based and chemical-free enriching process as well as the closed circulation system of the process water which serves both the whole mine and the enrichment process (Outokumpu, 2015). Importance of the environmental impact of the Kemi Mine is amplified by its closeness to the cities of Kemi and Keminmaa with the nearest habitants living less than 2 km away from the mine site. To show the cooperation with residents the Kemi mine organizes special “neighbour days” for the habitants of the areas closest to the mine. Also, information letters are sent to the neighbours, when changes that may affect the neighbours are being planned and executed."

Jan 1, 2016

By A. K. Raina

Blast induced damage to the final wall of rockmass in any civil or engineering application is a major concern to the rock excavation engineers. There are at least four distinct techniques practised by blasting engineers to minimise the damage to the parent rock during blasting that are classified as contour blasting. One of the methods to achieve a smooth wall or rock surface in blasting is pre-splitting, where blastholes in the final row are mildly loaded with explosives and fired first in sequence before the rest of the holes in a round of blast to achieve a split in rockmass. Since blasting is one of the most adopted methods for achieving a final wall in a desired shape, while maintaining the rockmass integrity, the design of pre-split blast assumes importance. There are several variables that determine the final shape of the pre-split face including the rock type, the drill diameter, the explosive characteristics, the orientation of major joints with respect to drill hole, the linear charge density, the spacing of drill holes and inclination of the drill holes. This study attempts to determine the importance and sensitivity of variables in pre-split blasting using historical data from open excavations of a hydroelectric project in India. Keeping in view the multitude of variables, low correlation of independent variables with responses and high level of interactions between the variables that define the blast results, it was found suitable to use ANN to determine the importance and sensitivity of the variables involved. A new method to determine the blast induced damage to rockmass, namely, undamaged area (AUD%), is introduced. Half Cast Factor (HCF%) and AUD%were calculated for a high wall and trenches by digital image analysis technique using the Fragalyst software. Joint spacing and linear charge density emerged as most controlling variables in determining the final result of pre-blast. The relative importance of other variables assuming significance in the case of both the designed outputs is also discussed. A comparative analysis of HCF%and AUD%on the basis of results obtained from ANN analysis is also presented. A futuristic approach concept has also been introduced.

May 30, 2021

Contents

Jan 1, 1985

By E. F. Paski

Geological materials are likely the most complex and challenging substances to quantitate by ICPOES (inductively coupled plasma optical emission spectroscopy). For complex materials having widely varying compositions, spectral overlap interferences govern detection and quantitation limits attained by ICPOES based analytical methods.

Jan 1, 1993

By David Cronan

"Most of the recent renewed interest in manganese nodule mining has been focused in the Clarion-Clipperton Zone (CCZ) in the NE tropical Pacific where nodules are rich in Mn, Ni and Cu. However, equally interesting, but compositionally different, nodules occur in the tropical central South Pacific (CSP). The CC Zone deposits lie in the International Seabed Area whereas those in the South Pacific lie mainly in the Exclusive Economic Zones of Island States, principally the Cook Islands and Kiribati. The CSP nodules should not be regarded as an alternative resource to CCZ nodules, as they are enriched in different elements. Rather, the CCZ nodules should be thought of as a source of one group of metals (Mn, Ni and Cu) and the CSP nodules the source of another group (see below), mutually complementing each other and to be mined in parallel for their different metals.Manganese nodule mining in the South Pacific has been mooted since the 1970s. However, new data on manganese nodule composition and abundance there have recently appeared. Also, a recently developed interest in 'rare', 'green' and 'technology' elements has necessitated a re-examination of old South Pacific nodule data for information on these elements (previously thought to be economically unimportant), and the re-analysis of the deposits to obtain new data on them. Additionally, current and possibly future applications to the UN to extend island 'continental shelf' areas necessitates an appraisal of the manganese nodules in these areas. These developments have prompted recent work that has helped to refine our understanding of the distribution and abundance of metals of traditional interest in South Pacific nodules, namely Mn, Co, Ni and Cu, but has also drawn attention to other elements of possible economic interest including titanium (Ti), vanadium (V) and the rare earth elements (REE)."

Sep 1, 2014

By Robert L. Marovelli

Organizational development that attempts to simultaneously deal both with training and with job design parameters as they relate to mine health and safety, productivity, and quality of life is one of several areas of research that the Bureau of Mines is pursuing. The Bureau sees potential in this particular effort for reducing accidents and injuries, improving worker satisfaction and health, and increasing productivity.

Jan 1, 1981

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999

By Jr. Gambrell

For more cost effective strata control, a fundamental understanding of the behavior of the support system is needed. To assist in this understanding for shield supports, behavior of a four-leg shield design used on a soft floor in an operating longwall system is presented. The shield was constructed having a split base and a split caving shield. Attention is focused on other-than-normal loading on the canopy and its effect on deformation of the lemniscate links. Examples of the typical bending and twisting deformations are given. Schematics of the canopy, caving shield, and lemniscates showing important forces and moments are presented. Approximate minimum values of the forces and moments are calculated. The need for use of more inclusive three-dimensional design techniques is demonstrated.

Jan 1, 1990

By David D. Eyer

Since the decade of the 1990s is nearly upon us, I have focused on what I see are the likely trends featured in new large underground coal mines 10 years from now. I do this from the vantage point of having been involved in the installation of large mines for more than twenty years. Little of the equipment resources we have available today was unknown when I entered the coal business in 1960. There were continuous miners, longwalls and diesel-powered equipment in Europe, monitoring systems, computers, heavy media separation systems, froth flotation and conveyors then as there are now. A substantial evolutionary process has occurred with these and other mining machines and processes. Some evolved only to die out, such as boring-type continuous miners; others, such as longwall systems, flourished. My intuition tells me that since there have been largely evolutionary rather than revolutionary developments in the near past, the same is true of the future, at least for the next 10 years. In other words, the elements of what are in the future are with US now. Some, such as computer-based applications, may evolve beyond our wildest dreams -but I doubt it.

Jan 1, 1988

By Ali Jaberi Zamharir, Abolfazl Shoghian‐Alanaghi, Hossein Aghajani, Arvin Taghizadeh Tabrizi

In this study, the leaching rate of molybdenite concentrate was evaluated in sulfuric medium, and the influence of the diverse oxidants including hydrogen peroxide, manganese oxide, copper sulfate on the leaching rate was studied. Also, the effect of the addition of the ethylene glycol to the hydrogen peroxide was studied and results showed that with the addition of ethylene glycol, the leaching rate is increased 55% from 41% up to 80.3%. The optimum condition is achieved as 0.7 M of H2SO4, 4.4 M of H2O2, and 3.5 M of EG at 30 °C within 4 h of leaching time and 500 rpm. Also, inserting the oxygen with the pressure of 6 bar to the leaching autoclave, the leaching rate is increased more up to 86.4%. Finally, the leaching process was studied kinetically and the determined mode of controlling factor was specified based on the activation energy which equals 46.252 kJ/mole indicating the chemical reaction mode.

Jun 5, 2022

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air pollution control is included. However, there are clear indications that natural gas supply from the contiguous 48 states and continental shelves will not indefinitely keep up with this rapid growth in demand. Projections are presented which define the extent of potential deficiencies from the 1970's to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale - by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current minemouth prices - 60-70 million' tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase is gas demand.

Jan 1, 1969

By B. A. Massey

Sooner or later, we'll encounter a subordinate, peer, or boss that will test our management skills to the limit. The chances are good that our formal educations have not fully prepared us to effectively handle the situation, and through trial-by-fire, we have learned that the management of people is often as much an art as it is a science. Assertiveness - as opposed to agressiveness - is basically positive persuation. Assertive management techniques can help combine the art and science of managment to sell ideas, accomplish goals, direct the workforce, and generally promote the corporate - as well as our own - objectives

Jan 1, 1986

By J. J. Reilly

The Vesta Mines of the Jones & Laughlin Steel Corporation operate in the Pittsburgh Seam in Washington County, Pennsylvania. This seam is overlain with a drawslate, 12" to 16" in thickness, which slimes readily when wet. Because of the need for a uniformly good quality metallurgical coal, the amount of reject, together with the top and particle sizes of the raw coal feed, is a serious problem at the Vesta Preparation Plant. The Preparation Plant operates two, seven and one-quarter hour shifts per day and processes 2,100 tons per hour of raw coal feed. The third shift is, used for planned maintenance of equipment. Since the water clarification equipment is so vital in insuring a uniform product, there is no alternative but that it be in operation at all times. To insure this continuous operation,. well-planned maintenance is a necessity. For years, Plant Management has kept performance records of the various units to determine the renewal dates of vital component parts, the length of wear, the various materials used in the manufacture of the equipment, and the labor cost for renewal. These records have been of inestimable help in planning an effective maintenance program to insure continuous operation of the various units.

Jan 1, 1959

By C. W. Overton

The operations of Bethlehem Copper are situated in the south-central interior of British Colombia at an elevation of 4900 feet above sea level. Main road and rail transportation systems pass through Ashcroft in the Thompson Valley, which is 28 miles by road from the minesite. The operation was the first low-grade open-pit porphyry copper mine in British Colombia. The minerals are chiefly chalcopyrite and bornite, while the rock is principally feldspar and quartz. In the outer fringes of the orebodies sane pyrite is present. Average grade of mill feed is 0.55% copper.

Jan 1, 1973

By B. Mishra, K. Savage, T. Evans, A. Noble

"Recent government initiatives and commercial activities have targeted asteroids for in-situ characterization, manipulation, and possible resource extraction. Though emergent technologies may be effective for such undertakings, uncertainties remain concerning the effects a space environment may have on the mechanical behavior of rocks. Various non-destructive rock characterization techniques can empirically predict in-situ rock strength on Earth; however, these techniques must be adapted to account for unique space conditions. In order to mimic one element of a space environment, various rock samples were evaluated after prolonged exposure to low temperatures ranging from -75°C to 0°C. Tests included uniaxial compressive strength, Schmidt hammer, and ultrasonic pulse velocity, while rock types included shale, limestone, and chalk. This data was used to generate a temperature correction for the non-destructive methods and evaluate the accuracy of these methods in predicting strength values. Overall, these results provide insight on the mechanical behavior of rocks at low temperatures and may be used to design robust systems needed for asteroid rock characterization INTRODUCTION NASA and various commercial entities have recently targeted near-Earth asteroids for exploration and scientific investigation to better understand their in-situ properties, mechanical characteristics, and formative processes. In particular, NASA’s Asteroid Initiative encompasses several studies and mission plans that will enable future investigations while vetting technologies that can be applied to deep space exploration. One component of the Asteroid Initiative is the Asteroid Redirect Mission (ARM). This multi-stage space mission proposes to rendezvous a robotic spacecraft with a large near-Earth asteroid. Upon approach and after landing, the spacecraft will prospect the surface and identify a multi-ton boulder (up to 5 m in its largest dimension) suitable for capture. The robotic spacecraft will engage the boulder, remove it from the parent asteroid, and return the sample to a controlled lunar orbit. Once the asteroid mass is in stable orbit around the moon, astronauts aboard the Orion spacecraft will engage with the retrieved asteroid for manned exploration that will include sample collection and geologic prospecting. Launch plans for the ARM robotic craft are expected as early as 2020, and manned explorations of the asteroid mass in lunar orbit are expected to follow sometime in the mid-2020s (NASA, 2015). Overall this mission will demonstrate NASA’s ability to intersect, manipulate, and redirect an extraterrestrial body, while supplying scientific information that is relevant for planetary defense and in-situ resource utilization (ISRU) applications."

Jan 1, 2016

By Raymond E. Zimmerman

The cleaning of coal by the use of jigs is one of the oldest methods of separating coal from its impurities. Although in many situations jigs have been replaced by other methods, by far the largest percentage of coal today is still being cleaned by some form of jigs. Some piston- or plunger-type jigs are still in use throughout the world; however, the greater number are air pulsated, generally called the Baum jig, named after the original inventor, Fritz Baum of Germany. This standard jig, with slight modifications, has been in use for over 75 years. Up until recently, however, it has had certain limitations in obtaining the high performance and efficiencies required in modern coal preparation practice. TO improve its performance, some radical modifications have been made in its design and operation SO that there is now a Baum-type jig giving much higher performance in terms of capacity, efficiency and sharpness of separation- This new jig is called the Batac, and the purpose of this paper is to describe its characteristics and present data giving its performance in treating coarse and fine sizes of coal.

Jan 1, 1974

By Jordi Vives-Costa, J. J. de Felipe, Lluís Sanmiquel, Maria Niubó

The article evaluates the convective heat transfer coefficient of ventilation air in a potash mine. The energy balance is obtained through thermal characterization of the ventilation air and rock, allowing for the calculation of heat transfer parameters. Different models for calculating the convective heat transfer coefficient are analyzed. The results indicate that the Pethukov–Kirilov, Gnielinski, and modified Dittus–Boelter models are optimal for this mine. The study also indirectly examines the conductivity of the adjacent rock, suggesting saturation throughout the studied section and the presence of liquid water upwelling in a specific section.

Apr 7, 2022

By Ernest Y. Baafi

The technique of linear kriging as a grade estimation method of mining blocks is reasonably established in the mining industry. Because of the nonbias condition imposed in kriging which requires that the kriging weights (?i) add up to one, negative weights are sometimes used in kriging. The use of negative weights is not justifiable from the practical standpoint. Also, negative block grades can be obtained in some extreme situations which makes no practical sense. To guarantee non-negative weights an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of non- linear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over or under estimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1984

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.

By R. Raby

During the 1980 decade, the rapid price increase for flake graphite has generated a high degree of interest for the discovery and the development of alternate occidental sources of supply in response to fluctuations in quality and availability from current producers. Alike many industrial minerals, graphite draws its complexity not only from its mineralogy and unique properties but also from the very large spectrum of industrial applications each calling for specific quality criterion. As new high technology uses are being developed, more rigid specifications will apply. Discovered during the latter part of 1988 by Mazarin inc., some 30 Km South of Fermont near the Quebec-Labrador border, the Lac Knife deposit was quickly identified as one of the world major long term alternate source of stable supply for this mineral. This paper also reviews the status of the project development as of late 1991, while updating previous papers published by Industrial Minerals1990 and Mining Magazine 1990.

Jan 1, 1992