Search Documents

By Sarah P. Guerrino

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1987

By W. A. Calhoun

The purpose of this investigation was to develop a procedure for removing excess iron from representative samples of bauxite ore from the Quapaw deposit of American Cyanamid Co., Saline County, Ark., in order to produce a beneficiated ore suitable for use in the alum industry, At the request of the sponsoring company, the samples were reduction-roasted at 800° C. and then magnetically separated. Although some rejection of iron was effected under these conditions, the general results were not satisfactory, A much more successful procedure, from the standpoints of both rejection of iron and recovery of alumina, consisted of a short (l5-minute), low-temperature (400° C.) oxidizing roast, followed by a 2-minute interval in a hydrogen atmosphere, then cooling to room temperature, and, finally, high-intensity magnetic separation to remove the iron.

Jan 1, 1957

By C. B. Manula, R. L. Sanford, R. A. Rivell

A central requirement for using simulation models is the need for retrospect testing to validate experimental conclusions. Acceptance of a model by managers and safety practitioners is more likely to depend on its tested performance in-the field rather than on the underlying logic or the validity aspects of the model itself. It is here that simulation bridges the gap between theory and useful design procedures. The original version of the rail haulage sub-assembly was success¬fully tested in the field (Sanford, 1969). However, the case studies that were described here involved single-stage haulage and restricted jobtypes from UGMHS. Since this report together with Volume VI (Production Subsystem) describes extensive changes and modifications to the rail haulage sub-assembly and UGMHS, field tests were necessary to verify both the rail model and the linking concepts to the Produc¬tion Sub-system. Mine Description The candidate mine selected for model verification works the 6 1/2 foot Pittsburgh seam. Shaft openings are used for manways and ventilation and a dual compartment slope for materials handling. In the bottom half of the slope, a hoist with track handles supplies and equipment. In the upper half, a 42 inch belt conveyor travelling at 450 fpm moves coal from a rotary dump to the surface. The immediate roof is shale with the first 12 inches taken during development mining. About 4500 raw tons are produced daily from seven face units and one spare working three shifts. At seven of the sections,

Jan 1, 1974

By L. A. Haas

The feasibility of removing sulfur dioxide by carbon monoxide reduction in a fixed-bed catalytic reactor was investigated by the Bureau of Mines. The reduction rate of sulfur dioxide with carbon monoxide was significantly dependent upon the iron and alumina content of the mixed catalyst. Maximum catalytic activity was obtained with about 40 percent iron-alumina mixture with a nominal gas mixture of 10 percent carbon monoxide, 5 percent sulfur dioxide, and the balance nitrogen. The synergistic effect of this catalyst mixture was explained by a dual reaction site mechanism, with both iron and alumina augmenting their specific sites at their interparticle contacts. The catalytic activity also increased with decreasing catalyst pellet size. With O.7-mm pellets, the entire pellet appeared to be catalytically active in a 2-gram catalyst bed. The apparent activation energy of the reaction was 18.3 kcal per mole in the temperature range of 350° to 600° C. Carbonyl sulfide (COS) was produced by the interaction of carbon monoxide and sulfur. The amount decreased with decreasing CO concentration. The ratio of COS formed per SO2 removed reached a maximum at about 400° C. The reaction rate appeared to be independent of S02 concentration in the range of 0.2 to 16 percent. The rate, however, increased directly with the CO concentration in the range of 5 to 20 percent. The presence of CO2 (<15 percent) had no appreciable effect on the rate. However, not over 0.5 percent oxygen could be tolerated. This method appears feasible for removing S02 from waste gas if the oxygen is removed prior to the catalytic S02 reduction process.

Jan 1, 1971

Although haulage truck collisions account for only a small percentage of haulage accidents, the likelihood of severe injury, or even death is very high when such a collision does occur. Most rear-end collisions also result in considerable equipment damage, creating a need for expensive repairs. To improve collision protection, some southwestern surface mines have, for several years, been fabricating and using extended bumpers. In cooperation with these mines, the Bureau of Mines has worked to improve this technology by evaluating the structural requiremnts of extended bumpers. How Extended Bumpers Help The Bureau found that when one large rear-dump haulage truck collides with the rear of another an extended bumper protects the driver of the vehicle that is struck by dissipating the impact energy into the rear tires and pushing the whole vehicle forward. An extended bumper also prevents the box on the truck that is hit from penetrating the cab of the other truck-a typical and serious collision hazard. A further advantage derives from the wide design of the extended bumper which helps prevent damage to truck ladders, thereby minimizing any entry or exit problems. Extended bumpers also provide safe work platforms at the front of large haulage vehicles.

Jan 1, 1984

By A. R. Rule

Research was conducted by the Bureau of Mines to develop a process for utilization of Idaho kyanite. A continuous gravity-flotation separation process was applied successfully to recover kyanite-group minerals from an Idaho ore containing about 21 percent combined kyanite, andalusite, and sillimanite. Dry magnetic separation of the concentrate resulted in a product containing about 90 percent kyanite at a recovery of 63 percent of the kyanite-group minerals in the ore, Alumina and silica analyses were within the range generally accepted for conversion to mullite, and the finished products had a pyrometric cone equivalent of more than 38. A recovered garnet coproduct may be of commercial value.

Jan 1, 1973

By James J. Olson

The Bureau of Mines recorded peak particle-velocity levels and vibration frequencies to determine the nature and intensity of ground vibrations for tunnel blast rounds at the NORAD Complex, Colorado Springs, Colo. Previous Bureau of Mines studies in quarries and underground mines had shown that scaling (dividing) the distance from the blast by the square root of the charge weight removed the effect of the various charge weights on vibration amplitudes. The analysis of variance tests performed on the NORAD vibration data, however, indicated that the cube rather than square root scaling exponent grouped the data more effectively. The empirical propagation equation, V = 560 (D/w1/3)-2.04, where V is the maximum peak particle velocity in inches per second, D is the distance from the blast in feet, and W is the zero-delay charge weight in pounds described the attenuation, with distance, of the particle velocities from the tunnel blasts in the Pikes Peak Granite of the NORAD Complex.

Jan 1, 1972

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing. the stage of measurement used in this chapter is what is normally termed ?mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1989

By Michael D. Fenton

The very modest-sized mineral industry of Afghanistan was burdened for another year with problems of internal strife occassioned by the presence of Soviet armed forces. Despite this, production of the few traditional commodities continued, and the mineral industry moved to develop additional mines and plants for both traditional and new products with considerable technical and construction assistance from the U.S.S.R. Among the limited range of mineral commodities for which production was reported, there were no startling changes between 1984 and 1985. Production of both coal and natural gas advanced only slightly, despite substantially higher 5-year plan goals, and cement output was down marginally. Probably the most significant development in 1985 was the Possibility that mine and/or smelter production of copper was initiated during the year.

Jan 1, 1987

By S. J. Page, J. A. Organiscak

Dust surveys were conducted around small truck-mounted rock drills operating at surface coal mines to assess their airborne respirable dust generation and in-service dust control methods. Of four out of seven drills sampled, respirable dust concentrations measured around the drill deck ranged from 8.68 to 95.15 mg/m with3concentrations ranging from 1.37 to 2.69 mg/m at distances 12.2 to 30.5 m downwind of these drills. The other3drills had noticeably lower respirable dust concentrations measured around the drill deck at or below 1.30 mg/m.3Rotoclone-type dry dust collectors were commonly used with dust being emitted from around the drill deck shroud, collector exhaust, and collector fines dumping. Wind speed and direction was also a factor in the dust concentrations measured on the bench. Dust control modifications were made to three rock drills to reduce their airborne dust emissions. Dust controls tested included water injection into the Rotoclone exhaust, Rotoclone exhaust extension, improved sealing of drilling deck shroud, shrouding the Rotoclone hopper dump process, and wet drilling. These control techniques showed noticeable improvement in dust concentrations measured around the drills. Finally, repositioning the drill operator showed that operator dust exposure can be improved by avoiding the dust cloud around the drill.

Jan 1, 1995

By Verne E. Hooker

Stress relief measurements were made at three underground test sites associated with the Henderson project, American Metal Climax, located in the rugged, mountainous region between Loveland Pass and Berthoud Pass on the Continental Divide in Colorado. Sufficient data were obtained to determine the three-dimensional stress ellipsoid for each site. The measurements were made at hole depths greater than one diameter of the mined opening; thus, calculated stresses are representative of premining in situ conditions. The vertical components of stress are in good agreement with overburden depth including the influence of mountain topography. Horizontal components of stress substantially increase with depth. These components are believed to be influenced by stresses presumably of tectonic origin. The largest measured principal stress was 5,900 psi at a depth of 3.708 feet. The predominant orientation of maximum principal stress for the determinations at greatest depth is in the NW-SE quadrants.

Jan 1, 1972

By Carlton E. Brown

The purpose of this report is to present results of tests on the effectiveness of a spray of water mist, commonly called compressed-air water blast or water blast, in reducing the concentration of dust present in the air shortly after blasting and during mucking of the blasted material. Many observations have been male on the effectiveness of such ,sprays, but published quantitative information on comparative dust concentrations with and without their use, obtained by dust-sampling methods in use in this country, is rare if not absent. Tests conducted in South Africa about 19164/ and more recently in England5/, 6/ have shown that such sprays reduce the dust concentration to very low values within a fen minutes after blasting,

Jan 1, 1938

By William G. Gruzenaky

The separation of yttrium and the individual rare-earth elements (lanthanons) from mixtures in which they occur has been a difficult problem through-out the years. Because of the increased interest in the various uses of these metals, the economy of their production may become of great importance. Studies relative to this problem, undertaken at the Federal Bureau of Mines Albany Metallurgy Research Center, resulted in the development of a solvent extraction method by which yttrium can be separated from the rare-earth metals. A separation factor of 10.93 was obtained between yttrium and cerium from a single-stage extraction, and a factor of 1.78 was obtained between yttrium and erbium from a multistage system. The valuable metals were extracted from euxenite by caustic soda fusion or by chlorination, and several separation methods were investigated. Partial separation of the yttrium and rare-earth element fraction was made by chemical methods and by solvent extraction. Thermal decomposition of aqueous rare-earth nitrates or selective ignition of yttrium and rare-earth oxalates yielded a fraction enriched in cerium. A fraction enriched in the light rare-earth elements resulted from a double sulfate precipitation, whereas a potassium ferrocyanide pr cipitation yielded a fraction enriched in yttrium. Precipitation with dimethyl phosphate yielded a fraction enriched in yttrium and heavy rare-earth elements. Enriched fractions were obtained with several solvent extraction systems. A system consisting of rare-earth nitrates, nitric acid, and tri-n-butylamine-3 methyl-2-butanone favored the separation of yttrium from the heavy as well as from the light rare-earth elements.

Jan 1, 1961

By John C. Edwards

A two-dimensional, time-dependent, mathematical model has been developed that describes fire spread along the walls of a ventilated duct. The model is based on the assumption that the leading edge of the fire zone propagating along the wall surface coincides with the isotherm for the fuel ignition temperature. The model includes gas-phase energy transport via radiation and forced convection inside the duct and solid-phase energy transport by conduction into the fuel lining. Product gases emitted from the fire zone are assumed to mix uniformly with the ventilation gas to produce an optically dense gas mixture at the combustion temperature that enters the preheat region. Numerical solutions of the model equations for a coal-lined duct (simulated coal mine entry) have been used to investigate the effects of tube radius, air velocity, combustion temperature, and optical density of the soot-laden gas upon the terminal fire spread rate.

Jan 1, 1977

By Francis R. Redfern

Newton&apos;s method of solving a nonlinear equation is employed to develop a least-squares acoustic emission source location method in which the spatial residuals of the location equations are minimized. These residuals, related to the distances from the least-squares source location perpendicular to the surfaces described by the location equations, permit location error to be estimated to first order along the spatial axes. The solutions obtained by this method are the best spatial solutions to the location equations in the least-squares sense. Also presented is a procedure by which the geometrical control of a transducer array can be evaluated using the rate of change of source location with fractional velocity change.

Jan 1, 1982

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1985

By D. E. Traut

A fluidized, countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future national needs. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous, except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid-leach-uranium solution and a strong-base, ion-exchange resin was studied, together with subsequent elution using an acidified sodium chloride solution. The effects of the number of compartments, compartment height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. Also examined were the kinetic and equilibrium relationships for the absorption and elution steps. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The columns system was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By G. E. Rennick, F. E. Armstrong, J. Pasini, J. R. Abrams

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 112 part per billion. Expand- able cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jul 1, 1972

By Dean H. Ambrose

A computer model was created that generates contact data by means of simulation while altering several variables associated with the machine and its operator. These variables include work environment, the operator&apos;s anthropometry, work posture, choice of risky work behavior, and the machine&apos;s appendage velocity. In the model, a contact means two or more objects intersecting or touching each other, e.g., the appendage colliding with the operator&apos;s hand, arm, head, or leg. This report documents the code development of special features of the computer model, random virtual human motions and behaviors, which made it possible for researchers to study hazardous interactions, such as contacts between the operator and machine. The original idea for random virtual human motions began with the need for a model that, when simulated, would experimentally mimic machine and human actions that could cause actual injuries or fatalities in the workplace. Injury incident investigation reports do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are also not feasible because of safety issues and ethical issues. Early investigation that evaluated the feasibility of random motions resulted in a primary programming structure and building blocks for code expansion. Basic motions and standard derivation data provided random parameters for the operator&apos;s movement in the random motion code. Experimenting with basic motions in preliminary models helped researchers devise a random motion technique that worked with xyz motion parameter values from basic motion parameters. Both values were the building blocks used in motion commands that comprised the core of the random motion code. When the code is executed in a three-dimensional computer model, it generates realistic starting positions for the operator&apos;s (virtual human) body and body parts and realistic motions mimicking a work sequence with a valid range of variation in movements. Researchers developed several rules for the random motion technique that, when applied, will maintain directional integrity of a virtual human&apos;s basic motions. From previous research, researchers formulated the algorithm that determines the behavior during machine operation. The decision algorithm was needed by the random motion code to randomly select what behavior to use for a simulation execution for a realistic representation of the operator&apos;s motions and risky behaviors during work tasks. The operator&apos;s chance of avoiding the moving appendage was also a concern to ensure that data reflecting a near-miss would not be considered a contact. Therefore, to filter a database obtained from simulations for actual contacts, it was necessary to track the operator&apos;s field of view and determine from this information when the appendage is in and out of the operator&apos;s view. NIOSH researchers successfully applied random motions and risky behaviors to examine the speed range of a roof bolter machine appendage for different workplace scenarios and compare statistically which is most likely to cause contacts (and possible injuries) to miners. Researchers in this study believe that the use of such simulations, treated with advanced statistical procedures, are extremely useful tools to evaluate the hazards of tasks where it is not possible to perform experiments with human subjects.

Jan 3, 2004

By James P. Ulery, Stephen J. Kravits, William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and Beth Energy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from overlying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine&apos;s ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the Iongwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 1992