Search Documents

By R. V. Ramani

This report, Volume I of the seven-volume Final Report on the U. S. Bureau of Mines research contract no. G0254030 titled Application of a Total System Surface Mine Simulator to Coal Stripping with the Pennsylvania State University provides an executive summary of the purpose and scope, objectives and results of the research. The remaining volumes of the Final Report, listed below, describe in detail model development, input and output documentation and the three case studies. Under the project, an existing surface mine simulator, Open-pit Materials Handling Simulator (OPMHS) was modified and extended for application to surf ace coal mining. In addition, two equipment selection models, and a cost model were also developed. Volume II: OPMHS User's Manual Volume III: Equipment Selection Models Volume IV: Surface Mining Cost Model Volume V: Application of OPMHS to an Illinois Mine Volume VI: Application of OPMHS to a South Eastern Ohio Mine. Volume VIII: Application of OPMHS to a South Western Mine.

Jan 1, 1978

The question of earth models has repeatedly arisen in our work. An accurate representation of the seismic properties is required for three reasons: 1.To be able to determine from a set of received arrival times, the location of a seismic source in the earth, and secondly the degree of accuracy required in the model used for calculating source location from the set of arrival time differences. 2. To be able to determine the expected arrival times at an array of geophones produced in response to a hypothetical source in the earth. 3. To be able to estimate received signal strengths more accurately. The work reported here on earth models is based on information from sever- al consultants and from others who expressed an interest in the problem and supplied information to us. II. COAL MINE GEOLOGY On one of our earlier assignments for the Bureau of Mines, Earth Science Research Inc. of Cambridge, Massachusetts prepared for us a short description of the lithology to be expected at coal mine sites. This description follows, together with the ranges of compressional seismic velocities (Figure I*) associated with typical materials comprising the layered structure of a coal mine area. Coal is primarily associated with fresh water sediments including sandstones, shales, and clays, and occasionally may be metamorphased to varying degrees. In the Appalachian Basin the coal beds occur within cyclical sequences of non-marine shales, sands tones, conglomerates, limes tones, and clays. The beds range in thickness from a few inches to 60 feet, averaging between 2 feet and 10 feet. They have generally broad areal extent, occasionally up to 5,000 square miles, and have an overall tabular or lens-like shape. Within a particular lens, local changes in thickness are normal.

Jan 1, 1974

By August J. Kwitowski

This Bureau of Mines report describes how the reinforcement mechanisms of untensioned, full-column resin bolts were determined during one underground study. Both axial and transverse shear loadings were identified for two instrumented resin bolts that replaced standard resin bolts in an opera-ting room-and-pillar mining section. The strain responses of resin bolt steel cores to local axial and transverse shear loadings are described. This information was obtained from laboratory testing of resin bolts installations; it was also used to analyze the data from the underground test.

Jan 1, 1980

By W. D. Bensema, J. W. Adams, W. W. Scott, H. Dobroski

Measurements of the absolute value of electromagnetic noise and attenuation along a hoist rope were made in an operating hard-rock mine, Lucky Friday Mine, located near Wallace, Idaho. Spectra of electromagnetic noise generated by various pieces of equipment, spectra of specific noise signals at various depths, and noise and attenuation on the 4250 foot (1295 meter) hoist, were measured. Three techniques were used to make the measurements. First, noise was measured over the en- tire electromagnetic spectrum of interest for brief time periods. Data were recorded using broadband analog magnetic tape for later transformation to spectral plots. Second, noise amplitudes were recorded at several discrete frequencies for a sufficient amount of time to provide data for amplitude probability distributions. A third technique gave attenuation data through the direct measurement of field strength at various depths. The specific measured results are given in a number of spectral plots, amplitude probability distribution plots and amplitude curves as a function of depth.

Jan 10, 1974

By S. J. Davenport

[The tremendous increase in mine mechanization since 1929 has increased markedly the application of electric power in and about the coal mines of the United States. Cutting, drilling, and leading machines have replaced hand-mining methods in nary mines. As a result, expansion of the gathering haulage has necessitated introduction of extensive feeder, trolley, grid other power wires. (1)3/ In spite of this vast mechanization the fatality rate from electric shock has been on the decline. However, there are still too many accidents, and efforts to eliminate electrical hazards cannot be relaxed. It is hoped that an acquaintance with the physiological aspects of electrical accidents will make workers end management aware of the lurking dangers of this very common and extremely dangerous form of energy.]

Jan 1, 1951

By Martin H. Stanczyk

Freezing to dewater typical Florida phosphate rock slime as demonstrated in laboratory tests appeared to have potential commercial use because of indicated moderate energy requirements, good compaction of dewatered solids, and effective recovery of usable water. After freezing, thawing, decanting, and filtering, batch freezing of gallon-size 13.7 percent solids slime samples yielded 42 percent solids products. Cationic amine, used as a process additive, yielded 46.8 percent solids product with significant filter area reduction. Semicontinuous 8 stage freezing tests also produced thickened slimes. Cooling and freezing 13.7 percent solids slime from 30° to minus 10° C required removal of 183 Btu per pound of slime; Carnot cycle calculation indicated that the theoretical minimum energy to transfer this heat was 27.8 Btu per pound. To produce 1 ton of 44 percent solids slime from 13.7 percent sol-ids slime, the calculated theoretical energy required for cooling and freezing was 52.3 kilowatt-hours. During the research heat capacity and heat of fusion data were determined for the slime at various percent solids.

Jan 1, 1971

By C. M. K. Boldt

This report summarizes five separate Bureau of Mines contract studies on the use of aerial photogrammetry, satellite transmission of in situ instrumentation information, and satellite imagery to monitor and update mine waste embankment data. The equipment used, methods applied, results, recommendations, and cost analyses are presented along with a bibliography of related investigations.

Jan 1, 1987

By E. Chin

Bangladesh, whose population probably passed 100 million by yearend, remained one of the poorest countries in the world, with a per capita gross domestic product (GDP) of $126.2 Its only economically significant mineral production was natural gas. A few other minerals or mineral-based commodities were also produced, generally for local consumption. These included cement, clays, nitrogenous fertilizers, limestone, salt, steel, and pilot plant production of ilmenite and rutile. Exploration for oil was a continuing quest, which was hindered by a lack of funding and a hesitancy on the part of foreign petroleum companies to make long-term or expensive exploration commitments. PODUCTION AND TRADE Production of natural gas continued to increase as more use was being made of the abundant gas reserves variously put at between 7 and 16 trillion cubic feet. The main consumers were nitrogenous fertilizer producers and electric powerplants, but other industries were converting to natural gas from imported coal or fuel oil wherever possible.

Jan 1, 1986

By David C. McHuron

The U. S. Bureau of Mines in their continuing research into sealants, selected MBAssociates to design, build, and test equipment and evaluate sealant as to its effectiveness is shale degradation. There were 20,050 sq.ft. of coal mine roof sprayed with a mine sealant and as a result, it has been estimated that the sealant coated roof has from 50% to 95% less roof falls than that roof which was not coated with sealant.

Jan 1, 1980

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550- and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974

By E. J. Kloos

The Bureau of Mines developed a test for evaluating gas masks designed to protect against phosphine gas; phosphonium iodide is used as a source of phosphine. Gas masks approved by the Bureau for respiratory protection against phosphine include the GMC-SS-1, Mine Safety Appliances Co.; the LG-10 and LG-10G, Willson Products Division, The Electric Storage Battery Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By Curtis H. Elder

In studies conducted by the Bureau of Mines, two test areas were hydraulically stimulated and exposed by mining: One in the Pittsburgh coalbed at the Vesta No. 5 mine, Washington County, Pa.; and one in the Illinois No. 6 coalbed at the Inland mine, Jefferson County, Ill. Induced fractures were contained totally within the coalbed with no adverse effect on the stability of associated rock strata. Induced fractures were vertical and were propagated normal to the direction of least residual tectonic stress. Gas production was increased fivefold to twentyfold by hydraulic stimulation.

Jan 1, 1977

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects world-wide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1992

By David A. Benjamin

In 1989 and 1990, the Bureau of Mines conducted a mineral resource investigation of the 122,000-acre Trinities study area, located in the Trinity Mountains of south-central Idaho. No identified mineral resources were delineated during this study. There are 58 lode mining claims within the area. Five localities contained elevated metal concentrations which may indicate precious metal mineralization at four localities and molybdenum-precious metal mineralization at another. Four of the five localities appear to form a northwest trend through the center of the study area. Twenty-eight individual sites contain anomalous concentrations of gold, silver, bismuth, molybdenum, and beryllium.

Jan 1, 1991

By W. N. Poundstone, W. M. Merritts, B. A. Light

A joint investigation by the Bureau of Mines and the Christopher Coal Co. at the Humphrey No. 7 mine, operating in the Pittsburgh coalbed in northern West Virginia, was undertaken to gain more insight concerning the hazardous emission of methane gas in mining. This report describes the equipment, procedure, and results. Horizontal bleeder holes drilled in the faces drained large quantities of methane, eliminating downtime of mining equipment. Also, larger quantities of methane were removed by forcing 14 to 25 g,.p.m. water at 25 to 200 p.s.i. 5 pressure into the bleeder holes. In one infusion test a fluorescein dye was added to the infusion water; in later mining operations, the infusion water was traced for a distance of 1,500 feet. With vacuum pump applied to the horizontal hole the gas-flow rate increased, and the methane content decreased. Tests indicated that methane and water infused in bleeder holes traveled along the bedding planes of the Pittsburgh coalbed at a faster rate than across the planes. Methane associated with coalbeds is produced by the slow decomposition of carbonaceous material in the absence of air and the presence of water. It is lighter than air and, depending on its concentration, forms an inflammable or explosive mixture with air. It is believed that methane is entrapped in and around the pores of the coal and adjacent strata--often under great pressure. In many cases where the strata have been disturbed by geologic movements the

Jan 1, 1962

By N. A. C. Smith

During the past, six, years, the Bureau of Mines has made and. published several hundred analyses of typical crude oils and 'has developed a system of interpreting the analyses and of classifying crudes. This system is presented here with. It is apparently equate for classifying crude oils into four main groups and has also been found very convenient in studying the geological relationships between crude oils, and the probable refinery yields of valuable products from them. Crude petroleum is morn to be a very complex substance. An analytical statement of its properties must, therefore, consist of two distinct parts, - first, the report of the results of the determinations made by the analyst in the laboratory, - second, the proper arrangement, classification and interpretation of these results so that the analysis, as a mole, will indicate the meaning- and the relative- importance of the essential characteristics of the oil.

Jan 1, 1927

By Richard F. Hewlett

The mining industry utilizes a vast store of knowledge, wisdom, and engineering talent in designing mining systems. However, the complexity of the required systems and the presence of numerous variables frequently necessitates raking important decisions without having adequate accurately detailed information. That many of the decisions made in the past were nearly correct, in the long run, is substantiated by the number of successful mining enterprises that exist in the world today. Subsequent to 1940, the disciplines of operations research and systems engineering were developed. The disciplines have produced methods of providing better information to persons responsible for making decisions.

Jan 1, 1963

By A. Gene Collins

The Bureau of Mines conducted a research study of the geochemistry of the Smackover Formation to determine what geochemical relationships are useful in exploration for and production of oil and gas. Samples of oil, gas, brine, and rock were collected and analyzed. The oilfied brines were analyzed by methods recommended by the American Petroleum Institute and by tentative methods of the American Society for Testing and Materials. The crude oils were analyzed by Bureau of Mines methods; the gas, by Bureau of Mines methods; and the rocks, by wet-chemical, atomic absorption, and neutron activation methods. The results were correlated and interpreted, and several geochemical relationships useful in exploration and production were found. These include the type and class of brine, organic constituents in the brine, redox potential, in situ temperature and pressure of brine, degree of sulfate and carbonate saturation of brine, and halide concentrations in the brine.

Jan 1, 1974

By Thomas W. Martin

This chapter includes tables from 1984 that were not available in time for publication of the 1984 Minerals Yearbook, but does not include corresponding tables for 1985. The value of raw nonfuel minerals produced in the United States during 1985 was estimated at $23.2 billion, an increase of $0.07 billion over the value for 1984. This is the third consecutive year that the value has increased, and except for a decrease in 1982, the value for each year has increased since 1971, or 13 out of 14 years. However. while the value of industrial minerals production continued to grow, reflecting the growth of the domestic economy, the value of metal mine production decreased in 1985 by 6%. This drop was more than offset by a 3% increase in the value of industrial minerals production because the value of industrial minerals produced was more than three times larger than the value of metals. The decrease makes 1986 the third year in the past 5 years in which a drop in the value of metal mining production occurred in the United States where production continued to lag behind growing world production. Domestic production of such major commodities 88 aluminum, copper, iron ore, phosphate rock, and zinc continued to decline owing to a number of international and domestic factors. Gold continued to be the most active commodity in the domestic metal mining industry. Despite lower prices, gold output increased to 2.5 million troy ounces, a 19% increase over that of 1984. The estimated annual production capacity of new gold mines beginning production exceeded 1 million ounces.

Jan 1, 1987

By Charles Prasky

This report describes bench-scale studies and pilot-plant development of the Bureau of Mines process for roasting iron ores with a ferrous scrap reductant, such as discarded automobile hulks, to yield artificial magnetite. Quality magnetic concentrates containing about 66 percent iron and 6 percent silica with iron recoveries of over 90 percent were obtained after roasting fine-grained oxidized or nonmagnetic taconite with unburned, sheared automobile hulks in a rotary kiln. The relatively complete oxidation of the lighter gage metal in the automobile during roasting resulted in a metallic byproduct consisting of the unconsumed heavier gage metal scrap. This residual or tailored scrap is potentially useful as heavy melting stock and has more value than the original automobile hulk.

Jan 1, 1970