Search Documents

By Clive-Workman Davies, K K. Kabongo, Mensah Frimpong

Given the capital intensity of the dragline operation coupled with rising cost of explosives, the onus is on mine operators to make maximum use of explosives in blasting to assist dragline diggability. At a surface coal mine in South Africa large boulders necessitating secondary breakage and in some cases completely unfragmented sections of a blast resulting in low dragline diggability were encountered in the interburden blast. Twelve blasts were therefore closely monitored and dragline productivity evaluated. The ultimate aim was to improve the overall blasting performance and hence increase dragline productivity. Three areas were in focus; fragmentation assessment, dragline productivity assessment and cost analysis. The studies indicated unsatisfactory explosive and initiation performance, problematic blast design and questionable operators performance. It is established that dragline cost account for 60% of the total mining cost whereas the drilling and blasting cost account for the remaining 40% and that improvement in dragline productivity results in automatic cost saving.

Jan 1, 1996

Several surface coal mining operations in North America are attempting to adapt microprocessor-based monitoring equipment as well as programmable logic controllers onto rotary blasthole drills, towards improving overall drill and blast productivity. These Monitoring While Drilling (MUD) systems permit the recording and processing of important drilling parameters such as rotary speed and torque, instantaneous penetration rate and weight on the bit, and enable the operator ultimately to optimize drill and bit performance. MWD systems on production drills in surface coal mines offer the potential to define mine bench geology in detail and in advance of explosives loading. Recent advance s in explosives and initiation technology will require such a detailed knowledge of ground conditions in order to be fully exploited. Additionally, the logic developed from drill monitoring technology will eventually enable full drill automation through feedback and control, once a more complete understanding of the influences of rock mass characteristics on machine performance is achieved.

Jan 1, 1988

By C M. Deosthale, V N. Pangal, M N. Rao

New Mangalore Port is the most important port in Karnataka State, on the west coast of India on Arabian Sea. It handles export of iron ore, granite, coffee, spices etc and imports of crude oil, fertilizers etc. Since 1991, after economic liberalisation by the Government of India, the exports and imports at this port got a boost. Hence the Port Trust felt the need to increase the draught by about 3 to 5 meters for access to bigger ships. In response to a global tender in 1995, the Dutch Dredging Company got the contract to remove 30,000 cu.m of hard granite bed rock, covering 28,000 sq.mtr. area for the Turning Circle and oil Jetty. The operations of drilling, blasting and dredging were to be carried out to deepen the area to about 15 m draught without affecting the normal trade at the Port. This was a time bound contract to avoid interruption by severe Monsoon rains.

Jan 1, 1999

By Sarma Kanchibotla

In mineral industry operations the insitu ore is’separated from the waste rock and is subjected to a series ofprocesses to convert it into a valuable product. Profitability of any operation in this industry depends on how eficiently the insitu rock (ore -I- waste) is converted in to the final product and how much value @ice) it commands in the market. Traditionally, the total process in mineral industry is classt@ed into two groups as mining and milling, and optimised independently without considering the impact of one over the other. This paper investigates the impact of mining operations (especially blasting;) on downstream processes and demonstrates the potential benefits of the “Mine - Mill Blasting” approach through simulations and case histories.

Jan 1, 2000

By D T. Froedge

To preface these remarks, it is not intended that this paper be a criticism of anyone or any organization involved in drafting the current regulations, for it appears that everyone involved in the process has made an extreme effort to be safe. We wish to show that in this case by making huge safety margins, we have created an unsafe condition in another area. That is by creating vast safety margins in the area of mobile transmitter intensity versus distance scales we have caused a severe handicap in the use of the mobile transmitter in securing blasting areas. The use of these mobile transmitters, which are absolutely essential in clearing areas where there are woods, mountains, or urban structures is virtually eliminated because of the safety factors prescribed in the regulations. We wish to show that these mobile transmitter safety factors are much too great, and can be traded off to increase the margin of safety in the ability to clear blasting areas.

Jan 1, 1975

Case histories in blasting show that Livingston's cratering technology has been applied successfully to blast designs with explosives having a charge length to diameter ratio not larger than 6. But the evaluation of experimental results such as the crater volume is tedious and sometimes impractical. A key analysis presented in the study shows that the optimum scaled volume relates well with the optimum scaled rupture limit, and the latter can be determined by means of high speed photography without excavating the blasted material. Through the studies of harvesting gypsum from a dried up settling pond the high speed photography approach has demonstrated to be effective for determining the optimum design for blasting plastic material.

Jan 1, 1987

By Gungor Tuncer, Erhan Bakirci, Ali Kahriman, Atilla Ozmen, O. Nuri Ucan, Savas Gorgun

There are several methods for demolition of structures but most of them depend mostly on conventional ways of using machines for breaking and crushing structural elements. However the need for lots of work force, expense and extreme amount of time for demolition, made most of these methods non-popular nowadays. Therefore, trials to accomplish a more economic and less time taking method lasted with the use of blasting. By applying controlled blasting on a suitable structure, the structure can collapse and break down to pieces in very short period of time, with no extra work force and cost. In spite of advantages of explosive demolition, the potential danger of explosives and the damage that the blasting may cause to surrondings, if not controlled properly, made people timid to the method especially in urban areas. Therefore, the pre-assumption by computational analysis has become an essential matter in the process.

Jan 1, 2002

By David Siskind, Mark Stagg

Vibrations from Dade County (Miami area) quarry blasting and structure responses were measured at 11 locations between February and April, 2000, and 10 homes were inspected to analyze the characteristics of their cracking and other damages. These results were combined with information collected by the County and other studies done in south Florida for a blasting impact assessment specific to this area. In addition over 40 quarry blasts in the nine-week monitoring period, about 800 measurements were available from previous monitoring in Dade and neighboring Broward counties. An overall worst-case analyses based on the highest individual amplitudes suggested that vibrations in some areas could have been as high as 0.35 in/s. While amplitudes in the study period were below this value, they were found to be relatively high for the distances and charge sizes. Attenuation with distance is less in Dade County than found elsewhere with quarries having to use scaled distances several times higher than similar sites in the north. Consequently, the vibrations are perceptible at very large distances.

Jan 1, 2001

By D K. Joyce, B Mohanty

In a previous paper, it was shown that a lack of clear understanding of the role of initiation mode on detonation characteristics often leads to under-utilization of the explosive system in blasting. This is of particular significance since the very large number of explosive initiation practices currently in use implicitly assumes that the blasting performance of an explosive is largely independent of the exact mode of initiation. This paper deals specifically with bulk-loaded and pneumatically-loaded ANFO under various initiation modes in small diameters. These include initiation by booster and detonating cords of various strengths, and combination of cords and boosters. The nature of energy release and energy partitioning between shock and gas energy have been studied in the underwater test as a function of charge diameter. The paper describes the relative merits of various initiation modes for specific charge geometries and confinement, under end- and side-initiated conditions. Guidelines have also been formulated for use in the field to match initiation practice with blasting requirements.

Jan 1, 1994

By Timothy Stark

At present blasters are strictly liable under tort law for personal injury and property damage caused by ground vibrations and/or air overpressures. The application of strict tort liability to vibration and air overpressure damage has resulted in litigation that has hampered and probably will continue to hamper the blasting industry. There are many case histories in which blasters have been sued for the appearance of cosmetic cracking, some of which have involved frivolous claims and marginal expert testimony (Oriard 1999). This litigation has resulted in additional costs to the blasting and construction industries and the American public because there are usually many plaintiffs involved and each case is usually adjudicated separately instead of under a class-action format. It is proposed herein that blasters not be held liable for vibration or air overpressure damages unless their conduct is proven to be negligent. A number of reasons are presented for raising the legal standard from strict liability to negligence including: (1) improvements in blasting technology that allow blasting to be conducted without substantial risk of damage and if damage does occur it is likely to be cosmetic, (2) establishment of conservative ground vibration and air overpressure damage limits for typical structures, and (3) established industry standards for construction blasting.

Jan 1, 2002

By Don Houston

Vertical crater retreat mining (VCR) requires initiation methods that minimize debris in the borehole. The use of detonating cord and shock tube detonators eliminates debris that could interfere with subsequent loading operations and avoids the cost of using drilling equipment to clear the debris. The explosive must not be sensitive to the strength of detonating cord used, otherwise timing will be affected. “Slicing and Dicing” of product before “Air mailing” down boreholes may facilitate loading, especially in wet holes, and can result in product surrounding the detonating cord. Cord sensitivity testing confirmed that having the detonating cord surrounded by product significantly increases the likelihood of an energetic reaction. Careful formulation and testing, based on a thorough knowledge of the application and the role of ingredients in affecting performance, ensures reliable initiation and avoids cord sensitivity. The use of certain metallic nitrate salts, even in relatively small amounts, was found to significantly increase the cord sensitivity of watergel formulations. Evidence of increasing cord sensitivity includes increasing amounts of damage to product and packaging, to ejection of product from the test pipe, then cracking of the pipe, followed by deflagration then detonation of the product. Predictably, the likelihood of an energetic reaction increases with product temperature, cord strength, and borehole diameter, while it is inversely related to product density.

Jan 1, 2002

By V Krishna Mohan, J Edmund Hay

This paper discusses the results of the gap sensitivity measurements made on water-gel explosives, sensitized by monomethylamine nitrate (MMAN) and flake aluminium, and one emulsion explosive. This study specifically deals with the effect of the mode of initiation, end or center, on the measured L50 values with air gap and coal dust gap for the above explosives. Similar measurements have also been carried out on a nitroglycerine (NG) - based explosive. The results show that the mode of initiation plays an important role in determining the air-gap sensitivity of these explosives. However, in tests carried out with the coal dust gap, the L50 ( grams of coal dust ) values for these explosives are close in both the types of initiation. The results indicate that the sensitivities of these explosives may be ordered in the following manner: NG-explosive>> Aluminized explosive ~ MMAN-explosive > Emulsion explosive

Jan 1, 1982

By J P. Tidman

The demand for more data on the detonation properties of commercial explosives grows as blasting becomes a more exact science. Proper use of this information by blasting engineers depends on the appreciation of the assumptions and limitations inherent in calculating energies and pressures of explosives. The strength of an explosive is usually a calculated energy value derived from a model of the explosive. The model may be simple or complex, depending on the thermo-hydrodynamic assumptions made. The calculated energy and pressures of commercial explosives are sensitive to assumptions about their reaction products. The equation of state describing the reaction product gases, the treatment of solid reaction products (e.g. reacted calcium and sodium nitrate and aluminum) and the reaction time are examined to show the variability of calculated results as a result of different assumptions. These same models of explosives also serve to explain phenomena of explosives such as the effect of charge diameter on V.O.D. (and strength) and decoupled explosives.

Jan 1, 1981

By Robin L. Simmons

Mining in the Genesis open pit has been conducted above the active haulage and ventilation declines of the Deep Star underground mine. Production has continued in both mines. The Deep Star haulage and ventilation declines, the primary and secondary egresses respectively, had to remain open and safe for travel until the new haulage and ventilation accesses were completed. Eventually, the upper 350 feet in each decline will be removed. The declines are in relatively competent calc-silicate hornfels with several high-angle, northeast-striking, clay-filled or open-spaced fault zones that create localized areas of poor ground requiring steel sets. To maintain the integrity of the declines, blast-induced vibration levels and damage were monitored in both declines after each surface blast. Seven geophones were installed in the declines to monitor peak particle velocity and peak vibration frequency. These data helped design subsequent blasts and predict expected vibration and damage levels. Blast design modifications included reducing the pattern size, reducing the powder factor and limiting blasthole detonations per delay. While limiting blast-induced vibration, these blast design modifications had to allow effective surface mining to continue. Linear regression analysis of peak particle velocity and scaled distance was used to determine the scaled distance necessary to keep the peak particle velocity under 2 inches per second. To date, the new ventilation raise, which is also the secondary escapeway, has been established and safe conditions were maintained in the original ventilation decline. Data collection and conscientious blasting procedures continue above the haulage decline.

Jan 1, 1998

By Lina Lopez, Jose Sanchidrian, Jean Du Mouza, Essaieb Hamdi

This paper evaluates the actual energy delivered by the explosives used in the fragmentation of rock during blasting vs. the available theoretical explosive energy. The evaluation of the fragmentation energy of the blast is first done. Fragmentation by blasting can be seen as a process in which creation of new surfaces within the rock mass is made by generation of new cracks or extension of pre-existing ones. From this idea, the fragmentation blast efficiency can be assessed as the fraction of the available explosive energy used for creation of new surfaces. The evaluation of new cracks area created by the blast is based on the SIMBLOC methodology and the corresponding fragmentation energy is then obtained by the Griffith theory. Secondly, the amount of energy delivered down to a certain pressure or volume along the detonation product expansion process, given by the useful work, is calculated. This is done by first determining the CJ state of the reacted explosive and subsequently performing an adiabatic expansion calculation of the detonation products from that state. W-Detcom code has been used for the calculations using the BKW equation of state with the Sandia parameter set. The fragmentation energy and the useful work are calculated for blasts performed in two mines in Spain. Multiple regression is applied to the results in order to give an assessment of the better description of the explosive energy .

Jan 1, 2002

By Quian Liu

Since the establishment of the CANMET Experimental Mine in Val d'Or, Quebec in 1991, research activities in rock fragmentation have been carried out not only in the underground laboratory but also in production mines in the north-west Quebec region. Among the instruments available for rock fragmentation, the Kodak EktaPro 1000 Motion Analyzer (also called the high speed video system) has been one of the most useful tools for monitoring blasts in both underground and open pit. This system is capable of recording events at rates from 50 to 12,000 frames per second (fps). The buffer memory has a capacity of storing 2050 images. To use this system in the underground, a steel box was made with a bullet-proof glass in the front to protect the camera. The processing and recording equipment are placed in an aluminum case which can be located about 30 m away from the camera via an extension cable. For each blast monitored, high frequency geophones and accelerometers were used to monitor ground vibrations and give a timing reference of the explosive detonations to correlate with the observation of the captured images.

Jan 1, 1994

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

Active avalanche control is the intentional triggering of avalanches while people are kept out of the hazard area. Explosives are frequently the most effective tool for triggering avalances. In a highway setting an avalanche control program will reduce total highway closure time, while providing greater safety to motorists and maintenance personnel. Avalanche control with explosives is effective when the snow is somewhat unstable and almost ready to slide naturally. Forecasting this condition involves having a network of local meteorological stations, examining snow structure, using mountain weather forecasts, doing snow strength tests, and having the results of ski and explosive tests. The method of delivery of explosives to an avalanche starting zone is governed by the accessibility of the starting zone. Common methods include; hand placing or throwing charges, remote delivery cableways, or "trams", surplus military weapons, and a compressed gas charge launcher, or "Avalauncher". Charges dropped from helicopters are also occasionally use. We have increased the effectiveness of our program by use of large elevated charges. Efforts are being made around the world to develop and utilize better methods for the safe, remote initiation, but procedures have varied dramatically between individual control programs. There is now a movement to review and standardize operational guidelines for avalanche control. Highway avalanche control is often done at night, during winter mountain storms. Heavy rain or snow, high winds, and high avalanche hazard, are common work site conditions. Commercial and economic pressures are increading, so methods that redice highway closure time are important. There are also many safety issues to be addressed in avalanche control work.

Jan 1, 2002

By Hung Tran, Denis Fleury, (Ken) Qian Liu

Pastefill technology has gained an increasing popularity over the past decade. The main advantages are: environmental performance (mainly in tailings disposal), low operation costs and ease of operation, as well as homogeneous properties. However, its weaker nature compared to other types of fill makes it more vulnerable to blast damage. In the last few years, Louvicourt Mine has experienced some cases of pastefill sloughage during the mining of secondary stopes. In order to reduce pastefill sloughage, some studies have been undertaken to investigate the causes and to find possible solutions by looking at stope design, extraction sequence, ground support and blast design. This paper presents the results of a blast damage study carried out at Louvicourt on the 860m level. The instrumentation included vibration monitors (using 6 sets of triaxial geophones grouted in the pastefill), a borehole camera to observe the damage in the pastefill, and a cavity monitoring system for three-dimensional surveys of the blasted stope. The test stope was mined out by four slot blasts and three mass blasts. Most of the damage was created by the mass blasts. It was found that the accumulation of ground vibration was mainly due to the low seismic velocities in the pastefill and the relatively tight delay between blastholes. In addition, there was a substantial difference between the critical PPV in the confined and unconfined pastefill. In practice, these findings have led to modifications of blast design to minimise the exposure time of pastefill walls to air. Such modifications included changes of blast sequence in secondary stopes and delay layout between heavily loaded blastholes. Over the paste two years, the implementation of new blast sequence has shown encouraging results in terms of reduced pastefill sloughage and dilution.

Jan 1, 2000

By Kirlk Yeager

"Ammonium nitrate (AN) is commonly mixed with a wide variety of additives to produce specialty formulations. Two additives commonly utilized are sodium nitrate (SN) and sodium nitrite (SNi). Application of the nitrite is primarily limited to gassing of emulsions. The nitrate, however, is incorporated in a wide variety of formulations. The effect of both these materials on the thermal stability of AN was examined. Experiments initially utilized lab-scale testing methods (sub-milligram sample size), such as differential scanning calorimetry (DSC), with scale-up to cook-off analyses (16 g) eventually applied. Labscale testing indicated that the presence of SN and SNi (both at 5 wt%) produced no harmful effects on the thermal stability of AN. The cook-off results did not agree with those from the lab-scale analyses, with both SN and SNi creating tremendous thermal destabilization of AN. These effects were seen at additive levels as low as 0.1 wt%. When SNi was employed as the additive, cook-offs became violent enough to create explosions in the testing apparatus. Although SN did not create as spectacular a destabilization, it did lower cook-off temperatures to approximately the same level as SNi. The dangerous situation created by SN andSNi seemed to be limited to cook-offs conducted in sealed vessels. If the SN/AN or SNi/AN formulations were allowed to cook-off in vented vessels, the thermal destabilization of AN did not occur. These results seemed to indicate that even “trace” amounts of what might ordinarily be viewed as benign additives could create significant destabilization of AN-based explosives under proper circumstances. Conditions created by blocked pumps, or deep boreholes could well overlap those produced in sealed cook-off vessels. In addition to showing the hazards potentially created by “benign” additives, the study also stressed that experiments designed to evaluate thermal hazards must include duplication of field variables to the fullest extent possible. "

Jan 1, 1999

By Advanced Initiation Systems Inc

10 years in R&D Last 5 years available commercially Worldwide Met strict approvals for manufacturing and use

Jan 1, 2004