Search Documents

By James Ballard, Charles H. Dowding

Recent Office of Surface Mining regulations have called for pre-blast surveys of residences within one-half mile of blasting. Unless lighting effects and the multiple origins of cracks are recognized, hurried (lowest bid price) pre-blast surveys may be more harmful than beneficial. Unrecorded, but pre-existent, cracks can be noticed by homeowners during blasting under special lighting conditions. This paper discusses important factors to note during pre-blast surveys, presents data collection forms and discusses the importance of photographic technique in recording cracks (both present and previously patched).

Jan 1, 1979

By Robert Slivinski, Kyle Hobbs, Michael Stern, John Willox, Brad Jewson

Prairie Mines & Royalty Ltd. produces over 12 million tonnes annually of thermal coal for TransAlta’s Sundance and Keephills power stations from the Highvale Mine. This opencast mine is next to a lake and is surrounded by cottages and farms, which means that blast vibrations and air overpressure have to be kept to a minimum.

Jan 1, 2008

Almost one half of Canada's total land surface is underlain by permafrost. This term describes the thermal condition of earth materials when their temperature remains below 0°C continuously for a number of years. The drilling and blasting of frozen materials requires more energy than the blasting of same in its unfrozen state. The cost of comminution could double in permafrost even with adequate organization, drilling equipment and proper explosives.

Jan 1, 1975

By Dadan Munawar, Benny Gunawan

Blasting at Sebesi in Central Tutupan Pit area in South Kalimantan, Indonesia is planned to be using emulsion, where used oil makes up 50% of the total emulsion fuel. The significant amount of used oil from various mining operation units had been of deep concern since it might be reused to implement environmental programs by substituting 50% of fuel with used oil in emulsion, thus decreasing fuel consumption and increasing efficiency by reducing fuel cost. Used oil must pass laboratory test to meet the Indonesian National Standards (SNI) No. 7642:2010 of used oil specification. Other considerations include the location which is adjacent to the mine office facilities with a radius of <1,750 meters (5,741 feet). Thus, appropriate methods must be performed to meet the SNI No. 7571:2010 of vibration threshold in order to implement safe blasting technique and prevent potential damage.

Jan 1, 2015

By K Ramachandra Rao

Joints, fractures and other structural defects bring anisotropic character Into a rock mass. Conventional methods of blast design In a rock mass consisting phyllites, mica schist etc., which are characterised by the presence of closely spaced, nearly vertical planar Joints, result In formation of large slabs which cannot be handled by the excavation and loading equipment without resorting to secondary blasting. Frequent secondary blasting Is not only expensive but also, Is a source of environmental hazard. Interruption of production cycles frequently, leads to uneconomical mining. This problem could be minimised by designing blasts which produce forces whose components along and across the joints/fracture planes Is lust sufficient to break the rock mass In both directions. Rock mass strength can be assessed from field and Laboratory tests. Projecting structural features with respect to bench orientation on a stereoplot helps In assessing magnitude and direction of force vectors required to fragment the rock mass to the desired size range.

Jan 1, 1995

By Thomas Palangio, Lyall Workman, Jack Eloranta, Tom C. Palangio

The fragmentation distribution of the blasted ore is an important descriptor of blasting results. Traditionally it has been hard to measure quantitatively. Developments in image analysis over several years makes it more feasible to measure fragmentation before crushing on a continuous basis. Post crushing, mill feed distributions can also be measured.

Jan 1, 2007

By Frank Lucca

This study is based on a six month study performed for Lee County, Florida. The study was based on blasting for land development and how this type of blasting affects structures. The study is investigates peak particle velocities and the relationship to other environmental and manmade forces that affect structures. The study also explores the effect of geology on blast vibration. After completion in Lee County, the study was then continued in the quarry environment in Vermont and extremely tight blasting environment of New York City. Charge diameters were 127mm (5 inches) or less.

Jan 1, 2006

By B de Raadt

After discussing mechanisms of collapse for the explosive demolition of towers in general and cooling towers in particular, author comments upon a blasting operation in which four cooling towers were involved. The intention of this paper is to present reliable parameters, generally valid for the explosive demolition of reinforced concrete cooling towers.

Jan 1, 1978

By Bob de Raadt

For a long time industrial underwater blasting has stood in need of a calculation method, for the determination of shockwave-proof as well as shockwave-effective charge distances to objects in water. After a brief discussion of the physical background of the shockwave mechanism in water, the author discusses an empirical theoretical computing method based on the "Bubble boundary" concept. The practical application of this model is finally shown in an account of a few underwater blasting operations in which charge weights of c.1-1000 kg were involved.

Jan 1, 1980

By D O. Tan Sky

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved.

Jan 1, 1980

By Sarah Guzzelli, Enrigue Munaretti, Anneliese Botelho, Jair Koppe

Drill and Blast (D & B) is one of the main operations in the mining production cycle, which aims to fragment rock according to a pre-defined plan for proper loading, haulage and processing specifications. In this sense, data from a Brazilian iron ore mine was analyzed, given emphasis on blasthole length, subdrilling and stemming. The D & B report, including mining data such as number of blastholes, length, and diameter and stemming aspects, was analyzed in order to be able to compare these results with the blast design. The study showed significant differences between the designed blasting pattern and that one obtained by the operation. As a consequence, problems such as inadequate fragmentation, incorrect size distribution and loss of energy, were identified. For example, when stemming has a different length than it should have, noise and flyrock can occur, including inadequate fragmentation and vibration in both situations. Therefore, a comparison between the usual D & B procedures and recommended D & B design based on literature reveals the most important deviations and their consequences. The study intends to identify solutions for simple problems, improving D & B operations and safety practices.

Jan 1, 2014

By Eddie L. Catbagan

The Escalante silver-bearing deposit, consisting of a relatively wide and continuous quartz vein, contains openings ranging from minute to a few feet wide on the footwall and hanging wall. These openings (water courses or vug holes) are I believed to have been created by the fluctuation of the water table.

Jan 1, 1983

By Jesus A. Pascual de Blas

After 30 years of development and introduction, electronic initiation systems are now well established in blasting applications, both mining, quarrying and civil works. In terms of blast technology, it could be considered that timing is the new challenge: how to define the most appropriate sequence to improve fragmentation, reduce vibrations, avoid dilution, eliminate damage… Some classic tools have been updated and adapted to the new scenario, and are giving us good performance; on the other hand, others should be considered obsolete, given the accuracy of electronic initiation systems has exposed these tools to incoherent conclusions. Besides, other tools have appeared and are in use, providing new approaches to old issues. Additionally, not only the technical side has to be considered: safety, security, economics are well present in daily blasting activity and affect to the final decision: are electronic initiation systems the right answer to my blast?

Jan 1, 2019

By Alday B. Andrews

A computer program called Seiswise that predicts the character and intensity of ground vibration generated by surface blasting operations was developed and field tested. The program uses the time histories of one or more pilot shots in combination with various initiation sequences to construct synthetic seismograms which are examined to select designs that will produce low levels of ground vibration.

Jan 1, 1990

By Sandor Nagy

The Explosive and Blasting Department of the Hungarian Mining Research Institute is responsible for the research and development of industrial applications of explosives. Appropriate explosives technology is developed for each application, including the explosive demolition of structures, which belongs within our charge.

Jan 1, 1977

By Roger Keller, Jason Ryan

A number of studies have evaluated excavation methods for the construction of subsurface facilities for a potential deep geologic repository for the disposal of nuclear waste at Yucca Mountain, NV. Many of these studies suggest that where TBM (tunnel boring machine) methods are not applicable and alternative mechanical excavation methods can not efficiently excavate harder rock drill and blast methods may be the most efficient means of excavation. However, a number of concerns regarding drill and blast applications have been raised in these evaluations, most notably the affects of blasting on the surrounding perimeter, as isolation of the waste by the natural barrier of the surrounding rock is a key element in the concept of a deep geologic repository.

Jan 1, 2001

Jan 1, 2002

By Daniel Roy, Chris J. Preston, Ron J. Elliott

This paper discusses the use of pressure transducers in water filled boreholes in conjunction with surface mounted geophones to gather field data for in-situ dynamic rock properties determinations. A high speed collector is used to capture the data in the field. The calculated P and S wave velocities and rock density measurements are used as input into the Blastcalc program where the values of Young`s Modulus and Poissons Ratio are calculated. The rock properties information is used along with geological structural data and explosives properties in a 3-D blast modelling program to calculate predicted fragmentation distribution and other blast performance criteria based on the proposed blast design.

Jan 1, 1996

By M. L. Mendes, J. Q. Nojiri, S. C. Botelho, A. P. Campanha

In February 28, 2001 JOULE coordinated the first tests with an electronic detonator in South America at an iron ore operation - ITABIRA MINES from the Brazilian COMPANHIA VALE DO RIO DOCE (CVRD) - the largest producer and exporter of iron ore in the world. ITABIRA MINES (CAU and CONCEI O) belong to one of the complexes, called the Southern System, producing 56 million tons of ROM as well as concentrated products and pellets. This paper is going to describe the tests at ITABIRA MINES with results indicating the improvement in the excavator productivity and reduction of the mining global costs (due to the better performance of the equipment and potential reduction of the maintenance cost).

Jan 1, 2002

By Roger L. Keller

Cautious, productive blasting is employed in the adaptation of a mobile crushing system extending into a highway through cut. In Hong Kong's final chapter of infrastructure development in preparation for handover of sovereignty, the vital link to the new governing country, The People's Republic of China, is now being completed. The Ting Kau approach and Tai Lam tunnel involves the removal of 6 million cubic meters of rock by drill and blast means. For the main-cut excavation (because of removal Iogistics) a unique adaptation of a Lokotrack crushing and conveyor transfer system is being used. The characteristic narrow working area associated with through cuts, positioning of equipment, and production demand place many limiting factors on blasting. Add to this the strict criteria set by the local regulatory body, the Hong Kong Mines Division, and nearby vibration limiting structures (13mm/sec), has led to highly cautious, fine-tuned blasting.

Jan 1, 1998