Search Documents

By M. A. EI Zeky, A. E. El-Nikbaily, M. A. Shahin

"Possible mechanisms of microsilica dust formation and factors affecting its quantity have been discussed. General mathematical models to predict the dust quantity based on electrical and coke consumptions, and flue gas temperature as functions of silicon recovery in the process and silicon content of the alloy have been established. It has also been shown that the flue gas temperature can be used as an additional process control parameter. Comments are made on the effect of the dust formation on the whole process economics and it is pointed out that the formed microsilica dust is a valuable by-product and not an industrial waste. INTRODUCTIONFerrosilicon is produced in electric arc furnaces with submerged electrodes. The charge mixture consist s mainly of quartzite, coke as the reducing agent and iron chips. The products are ferro silicon and carbon monoxide, various other volatile materials, water vapour and silicon monoxide gas. Carbon monoxide and silicon monoxide oxidize at the charge surface when mixed with air entering through the furnace hood openings. The off-gas contains a considerable amount of dust, which is mainly very fine particles of silica formed as a result of oxidation. The emission of dust containing gases to the atmosphere causes serious pollution problems to the environment. Therefore, the control of the formation of the dust, preventing it from escaping to the atmosphere, and dealing with this very fine dust collected from the flue gases represent important technological and economical parameters in the ferrosilicon production industry.This paper is concerned with the relations between the quantity of formed micro silica dust, as a function of both silicon recovery and silicon content in the alloy, and various other technological parameters; and their possible effects on the energy consumption and economics of the whole process."

Jan 1, 1989

By J. M. Skeaff

"The main solution, ore and residue pulp streams in the Rio Algom Quirke I uranium mill at Elliot Lake have been sampled and analyzed for radium-226. Analysis of the ore and leached residues indicates that Ra-226 dissolves and precipitates within the first pachuca tank. A maximum of approximately 0.2% of the Ra-226 in the ore remains in solution during leaching.IntroductionConcern over the acid drainage and radionuclide dissolution problems associated with uranium tailings disposal sites in Canada has prompted investigation into methods for improving current uranium processing practice.Present commercial practice usually involves leaching of the uranium ore with sulphuric acid, ion-exchange separation of the uranyl sulphate complex from the leach liquor and"" precipitation of the uranium as yellowcake. Daughter products of U-238, such as Th-230, Pb-21O and Ra-226 remain with the tailings and undergo long-term dissolution.Table I summarizes the probable behaviour of the radionuclides during milling. The concern here is with Ra-226, because it will deposit in the bones if ingested and is ""thus considered a serious health hazard(1), Similarly, Po-218 and Bi-214, which are daughter products of Rn-222, can be retained in the lungs and are considered to be the principal sources of radiation dosage(2) arising from the inhalation of Rn-222. Previous investigations(3-9l indicate or imply that Ra-226 undergoes redistribution during milling. However, detailed published information on the behaviour of Ra-226 in the uranium milling process appears to be lacking. A knowledge of the behaviour of Ra-226 in uranium mills, particularly during leaching, could lead to improved methods for its control.This paper reports the occurrence of Ra-226 in the Rio Algom mill. The main objectives of the study were to determine (1) the distribution of Ra-226 within the solids, (2) at what point, and how rapidly, redistribution occurs and (3) whether there are high concentrations of Ra-226 in solution."

Jan 1, 1981

By D. A. Trotter

"Low-pressure sodium light sources have been available for several years, but have not received wide acceptance in underground mining. This is because they are difficult to operate using DC power, they are not an intrinsically safe light where explosive gases may be encountered and they give poor colour rendition.With the need for energy conservation, several Canadian hard-rock metal mines are now changing their lighting to low pressure sodium, as it has the highest efficacy of any light source in terms of lumens per watt. Studies have pointed out several other advantages as well. Glare can be controlled, they penetrate fog well, they are easily maintained, they have a long life and they give the highest visual acuity when compared to other types of lighting. As well, in an underground mine, contrast is much more important than colour for task identification. For close work, the colour problem is alleviated with the use of cap lamps.Case studies are presented from Canadian practice. These show how the lights are modified for underground use, calculations preceding light installation, and how and where the lights are installed in the underground environment. Mention is made of worker reaction to the lights and possible physiological effects.IntroductionThe importance of good underground lighting to the total environment of mining cannot be overemphasized. In addition to the obvious benefits of improved worker morale, available studies show that good lighting practices reduce accident severity and frequency as well as increase production."

Jan 1, 1982

By V. Maazallahi, A. Rouleau, A. Saeidi

"The geometry of the terrain topography before and after the failure are the essential factors for analyzing a landslide and for the design of remedial works. This paper presents a method to determine these factors, considering that the determination of the slide surface profile is difficult and costly using traditional methods and the pre-slide topography data is often not available. The presented method to locate the 3-dimensional geometry of the slide surface is based upon determining the slide surface in 2- dimensional vertical sections. This method utilizes post-slide topography of the area to determine the pre-slide topography and uses equations to estimate the pre-slide situation using a statistical process applied to points located on the sliding mass. This method is tested on the Maskun landslide in Iran. The results indicate the applicability of the proposed method to obtain the key factors for the back analysis of a landslide in a cost effective manner.INTRODUCTIONProbably the most reliable method of determining the strength of soil and rock mass is to back analyze a failed or failing slope (Caia et al. 2007; Wyllie & Mah, 2004). This method is used in geotechnics for estimating geotechnical parameters of the rock and soil mass (Sakurai et al., 2003; Frayssines and Hantz, 2009; Cepuritis et al. 2010), but it requires that the failure mode is well established and that there is complete and precise information available on the slide surface and the sliding mass (Sjöberg, 1996). Measurement of the slope profile before failure provides the basic information required for a back analysis (Hock & Bray, 1981). The post-slide topography is another key factor. The back analysis process for determining the actual strength parameters of soil or a decomposed rock mass after a landslide requires knowledge of the sliding mass geometry, both before and after the sliding event. Many studies are reported in the literature about the application of back analysis for determining geotechnical and geomechanical parameters of rock and soil mass (Sakurai et al., 2003; Cepuritis et al. 2010; Frayssines and Hantz, 2009, Hussain and Stark, 2011), but they generally present little information about the geometry of the slide surface, and the weight of rock and soil mass that slid, although these factors are the most important parameters for back analysis process. Liang and Xue-song (2012) determined the slip surface having the minimum factor of safety (called critical slip surface in deterministic analysis of slopes) and the slip surface with the minimum reliability index (called critical reliability slip surface), but they have not considered the actual profile and geometry of the slide surface. Rocscience (2013) proposes the back analysis option in the Slide software for slope stability study, but it requires an imposed slide surface as input; alternatively, one can estimate by a finite element analysis the surface with the minimum factor of safety. However, this estimated surface is very likely different from the actual sliding surface, considering the uncertainties in input data of the finite element method."

Jan 1, 2015

By BARRY BANNATYNE

Gypsum in Manitoba is quarried from the Jurassic Amaranth Formation a1 Gypsumville and Harcus; it has been mined near Amaranth and Silver Plains. At Gypsumville, gypsum is carbonate- free but has thin clay laminae between gypsum layers; the rock is folded in places, and some anhydrite is present. At Harcus, gypsum contains scattered dolomite, both as patches in a penemosaic pattern and as thin layers; small chalcedonic concretions also can be found. The quarry at Harcus was opened late in 1978 and currently produces about 100,000 tonnes annually. The two inactive mines near Amaranth operated from 1932 lo 1963 and from 1967 to 1970, and contain a central anhydrite layer. The mine near Silver Plains was flooded from an underlying artesian aquifer in 1975 and has not been reopened. Manitoba gypsum is used in cemem plants in Mani1oba and Saskatchewan and in wallboard plants in the three Prairie Provinces.

Jan 1, 1984

By J. Keith Haddock

"The Luscar Mine is a metallurgical coal mine located in the foothills of the Canadian Rockies, 41 km southeast of Hinton, Alberta. The mine is operated by Cardinal River Coals Ltd., a 50/50 joint venture between Luscar Ltd. and Consolidation Coal Company of Canada. The mine produces a high quality medium volatile metallurgical coal which is sold on the export market principally to Japan and South Korea. Operations consist of a surface mine with capacity to produce 3.0 million tonnes per year and an underground mine which is currently mothballed due to market conditions.GeologyBedrock units within the Luscar minesite are of Devonian to Upper Cretaceous age. The commercial coal measures in the area are, however, confined within the Lower Luscar Formation. The Luscar Formation consists of a 460-metre thick sequence of interbedded sandstones, shales and coal seams. The sequence is primarily deltaic in origin, and is bounded to the north and south at the Luscar mine by tectonically induced thrust faulting.The only mineable coal seam at Luscar is referred to locally as the Jewel seam. Average thickness of this coal measure is usually 10.5 m to 14 m, although in some areas folding and faulting has produced ""pods"" of coal from 15 m to over 40 m thick while in others the structural deformation has thinned the coal to 3.0 m to 4.6 m. Waste within the Jewel seam seldom exceeds a metre of shale, carbonaceous shale or infrequent sandstone stringers.Reserves and Coal QualityProven surface mineable reserves, based on pit scheduling through 1996, are 50.8 million raw tonnes. An additional 19.2 million raw tonnes are contained in possible extensions to the present planned operations. These surface mineable reserves are considered to be those reserves within 155 m of the surface. Underground reserves, located within 770 m of the surface show that 25.7 million raw tonnes have been proven to date in additon to 27 .5 million indicated and 260 miIJion inferred.Coal specification at Luscar Mine is as follows:"

Jan 1, 1985

By B. Lewis

Paper did not make deadline for printing

Jan 1, 1982

By J. G. Stevens, S. W. Colley

"Selective separations of metals and ions in mineral extraction and refining are becoming more challenging as ore bodies become more complex and environmental pressures increase. The separation and containment of mercury produced in gold mining are a factor in the profitability and operability of mines. This paper will discuss the development and implementation of the Johnson Matthey HgFree selective mercury removal process. The process is designed to selectively recover co-leached mercury from either heap leach pregnant solutions at ambient temperature and low mercury concentrations, or electrowinning pregnant solutions at elevated temperature and high mercury concentration, without affecting gold or silver recovery. The process utilizes a highly selective adsorption-desorption step in which mercury is removed quantitatively by the HgFree adsorbent without adsorption of gold, silver or other metals present. Development of the original HgFree adsorbent has resulted in a process whereby mercury can be recovered as an inert salt and is never present as the free metal. The HgFree adsorbent can be regenerated and recycled in situ, and is capable of being reused multiple times. The overall process is compatible with existing gold mining and recovery practices and offers significant environmental and sustainability benefits, including reduction or elimination of the need to retort mercury with a subsequent reduction in potential mercury air emissions. Development of the HgFree adsorbent and process will be discussed along with a pilot operation at two operating mines.INTRODUCTIONMany gold ore bodies contain high concentrations of mercury which when extracted with cyanide, co-extract with the gold and other metals. This mercury is carried through the process with the gold, posing environmental and technical issues when it is separated from the doré. This paper describes a method to selectively adsorb mercury from the gold recovery circuit while it is in a soluble form, leaving gold to be processed as normal. The removal of mercury from the circuit eliminates the need for mercury retorting of doré and so reduces the potential environmental impact of fugitive emissions of elemental mercury."

Jan 1, 2016

By T. Hartmann

The presence of crud represents a permanent challenge for solvent extraction in the hydro-metal industry. The crud is a stable emulsion which slowly spreads along the phase boundary between the aqueous and organic phase. The crud can significantly impair the efficiency of hydro-metal extraction because the phase boundary between the aqueous and organic phases assumes substantial proportions, and the settlers cannot react flexibly. In a chain reaction, all settlers connected in series become infected with crud. The transfer of organic phase to the electrowining (EW) cell can cause 'cathode burn'. Continuous treatment of the crud is extremely effective and reliable with a 3-phase separating solid bowl centrifuge. All three phases are separated distinctly from one another. All associated process steps exhibit a steady uniform efficiency. First and foremost, they ensure a reliable, continuous extraction process and, second, they recover valuable re-usable organics from the crud.

Jan 1, 2007

By M. Ghiani, P. Carbini, R. Ciccu, C. Del Fà

"This paper is concerned with the problems inherent in the efficient and economical processing of the fine fractions of a coal from the Sulcis basin (Sardinia, Italy) whose characteristics are typical of low-rank coals occurring in the Mediterranean region. Three different techniques, based upon surface properties, are examined. Flotation can be very efficient from both a technical and economic point of view, provided care is taken in the modulation of the flotation pulp. Interesting results have been obtained with oil agglomeration and this method could be economically feasible. Finally, electrical separation has proven a viable technique, although it entails preliminary drying.Besides discussing the problems encountered in the experimental research, some significant results of general validity are also given. They demonstrate that cleaned products can be obtained with fairly interesting recoveries, thus opening the way to advanced research aimed at setting up the most suitable technique for industrial application. IntroductionAs a result of the oil crisis, which caused a major upset in world energy supplies, the last ten years have seen a revolution in the energy policies adopted.In particular, the status of coal, which seemed destined to decline in view of the availability of liquid fuel, has had to be re-examined. The need to meet energy demands under improved reliability conditions and controlled prices through a broader and more flexible diversification of sources of supply has evoked, especially in highly industrialized countries, a renewed interest in coal. The result has been a consistent increase in demand and production as well as investments in new mines and the reinforcement of the infrastructure.This turn of events has also lead to a re-evaluation of young low-rank coals, hitherto considered uneconomical and thus neglected, because of their low heat value. In fact these coals, which have a high ash content, may also be relatively highly contaminated with sulphur. The above drawbacks, which still today preclude the widespread use of these coals, are bound to create even greater problems in the future as increasingly restrictive environmental control imposes, without exception, recourse to cleaner fuels."

Jan 1, 1986

By P. R. Brito-Parada, G. Bhutani

"The physical processes occurring in flotation columns are very complex as they take place at different scales over a range of sizes and multiple phases. Column design and optimum operating parameters are usually obtained from empirical studies and although progress has been made on its numerical modelling, most column models rely on simplifications that do not fully capture the hydrodynamics. In particular, Computational Fluid Dynamics (CFD) models of the pulp phase in flotation usually assume the bubble population to be monodispersed. While this assumption may be reasonable in some situations, the polydispersed nature of the gas phase can have a significant impact on the predicted flotation rates.Techniques to model size distribution do exist in the literature and have been rigorously analysed in the past two decades for bubble columns, which are very similar to flotation columns from a hydrodynamics point of view. In fact, available CFD models of flotation columns are an extension of bubble column models, sometimes including additional equations for solids treated as passive scalars. This work focuses on the development of an efficient CFD model for flotation columns. The bubble size distribution in the column has been modelled using the Population Balance Equation (PBE), which is solved using the Direct Quadrature Method of Moments (DQMOM). Coupled with the PBE, the multiphase flow equations in the column have been modelled using the standard Eulerian–Eulerian approach. The solution of this coupled system has been made tractable in this work with the implementation of a highly parallelised adaptive-mesh finite element method. This powerful framework has been implemented in the open source CFD code Fluidity and it allows the carrying out of detailed simulations of flotation columns in 2D and 3D, with important implications for industrial column evaluation and design."

Jan 1, 2016

By J. G. Schofield, R. C. Francki, K. M. Donaldson, F. E. Ham

"Developments in pyrometallurgical technology have led to larger furnaces operating under more intense process conditions. In order to maintain the reliability of these furnaces, which are frequently single-line units, the design of the refractories, cooling systems and bindings has become more critical. Traditional thermal and chemical requirements for the refractory to resist slag attack must still be carefully determined. The larger, modem furnaces have placed a new emphasis on the structural properties of the refractories as well as their thermal properties to suit the extensive cooling systems. Based on operating experience, supported by computer models, the refractories and bindings are designed to work together to accommodate the thermal expansions and contractions in order to minimize permanent furnace growth and the risks of leaks. IntroductionElectric furnaces are used extensively in smelting copper and nickel ores and concentrates. Laterite nickel ores and high-magnesia copper, nickel and platinum sulphide concentrates are smelted virtually exclusively in electric furnaces to accommodate the high melting point of the slags produced. Although a number of smelting processes using oxygen-enriched and/or preheated air have been developed to replace reverberatory furnace smelting of conventional copper and copper-nickel concentrates, (lnco, Noranda, Outokumpu, Mitsubishi) electric matte furnaces remain a strong process alternative for these concentrates, either as the primary smelting vessel or for cleaning the slags produced from these processes.The development of large, high-powered furnaces has been an important factor in the growth of electric smelting technology, as evidenced by the list of operating matte and ferronickel furnaces shown in Table I. Because the compressive forces required to maintain a tight, leak-free furnace increase with furnace dimensions, the selection and design of the furnace refractories, cooling systems and bindings require increased attention."

Jan 1, 1993

By Sylvain Castonguay, Sylvain Pilon

"Operator competency is an important factor in the safe and successful operation of today’s complex processes. Competent process unit operators deliver superior performance and results. In greenfield projects, operator competency is particularly critical, as the lack of specific operations experience must be offset with proven practical knowledge and skills to avoid mistakes that can cost millions in terms of start-up delays, production losses and equipment damage. It is, therefore, important to know precisely what competencies are required for a project or site, and what any gaps in operator competency need to be addressed and improved. The success of plant commissioning, start-up and sustainable operations is directly tied to operator competency. The significant investments required for new projects, the exploitation of more challenging ore bodies, and the increasing complexity of plant operations have placed renewed emphasis on the need for competent operators. Furthermore, many large capital projects are being developed in remote regions, often with ties to the delivery of social benefits for the local population in terms of jobs, training and other development opportunities. While automation and processing technologies have helped do more with less, indicators now point to a bottleneck in human performance limiting operational results.Automation industry development in managing abnormal situations, including solutions for simulation and operator training, has produced applications to provide customized and flexible training methods. This paper will discuss tools to automate the operator competency process in order to guide trainers to effectively teach, measure, control, provide feedback, and monitor operator skills. Today’s competency management solutions can be effectively applied throughout the course of an operator’s professional life, as a guide to hiring new operators, for developing competencies to support operations, and also to develop and refine best practices and share lessons learned."

Jan 1, 2016

Caterpillar Inc The world's largest manufacturer of construction and mining equipment, diesel and natural gas engines and industrial gas turbines. Technology leader in logistics, construction, transportation, mining, forestry, energy and electric power generation.

Aug 1, 2013

By Jehan Rondot

Les bancs de quartzite inhabituellement purs et epais decouverts lors de la cartographie geologique de la region de Charlevoix sont maintenant entres au stade de !'exploitation et se revelent etre une richesse naturelle durable pour cette region. Les etudes stratigraphiques effectuees dans cette partie (Quebecia) du bouclier canadien indiquent que la succession: lo. complexe a amphibolite et leptynite a la base, 2o. quartzite et gneiss a sillimanite, muscovite et gneiss calcosilicate et conglomeratique au sommet est constante sur de grandes distances (de Charlevoix a la Basse Cote Nord) et represente une sedimentation continentale et de plateforme, peu epaisse, du proterozotque inferieur. La purete et la grande epaisseur du quartzite s'expliqueraient par un processus de sedimentation continentale complexe ou se succedent climat tropical-humide et glaciaire-aride et transport fluviatile et eolien. Parmi la multitude de depots de quartzite qui existent dans le monde, peu sont de qualite superieure. Or, de par sa composition chimique, le quartzite de La Galette se compare avantageusement a ceux des meilleurs gisements des Etats-U ni s, de l'Europe de l'Ouest et de I' Afrique du Sud. D'acces facile pour l'exploitation, les gisements ne sont qu'a une quarantaine de kilometres de Baie Saint-Paul ou de La Malbaie, sur le SaintLaurent. L'utilisation en metallurgie du quartzite de La Galette comprend la production de silicium, de ferro-silicium et d'autres alliages de silicium . La composition du quartzite est en outre appropriee pour la production de carbure de silicium et de silicate de sodium. Les fines peuvent etre utilisees pour la fabrication du verre et comme matiere de charge.

Jan 1, 1984

Presentation Plan Hoist ropes ?Importance ?Mandatory and routine Inspections Continuous monitoring of wire ropes for mine hoisting ?Why a continuous monitoring of mine hoisting ropes.? ?Description of the ??Contiscan?? monitoring system ?Information data gathering Advantages of the ??Contiscan?? monitoring system ?Visual rope inspection on daily basis ?Monthly inspection ?Payload capacity flexibility and potential increase for deep mining operations. ?Periodical inspections by external experts ?Importance of the costs associated with hoisting production shutdowns. Commercialization and availability

Aug 1, 2013

By Akira Fujisaki

"The oil crisis accelerated the change of non-ferrous metals' demand structure. Maturing societies in developed countries and preference for lighter, thinner and smaller products are eroding the non-ferrous metal industries' growth potential. Inventory-control, stockpiling and developing new demand are measures Japanese smelters have taken to cope with the changing demand.The most effective means for risk management of product demand lies in the cooperation between ore producing countries and metal consuming developed countries to assist developing countries in their efforts to ""take-off"", which in turn will bring about a surge of demand for metals.SummaryThe non-ferrous metal industry in the world is suffering its most serious slump since the war. With some of the markets of the advanced industrialized countries approaching saturation point and economized usage of natural resources and substitution growing, the possibility of a quick recovery of the demand for base metals is dim.To cope with the changing product demand Japanese producers have had recourse to such measures as strict inventory control and stockpiling for the purpose of stabilized imports. They have also tried hard for securing raw materials and promoting new field s of demand but the very core of ""risk management"" has been the diversification of line s of business to bolster and stabilize the foundation of management of the non-ferrous metal industry in Japan.To see the demand for nori-ferrous metals recover from the slump and be put on a path of solid development, we have to wait for the economies of the developing countries to ""take off"" and for its realization the economies of the developed countries must be reactivated with new growth industries playing a leading role, and the transfer of technology and money recycling must be carried out smoothly under an orderly international trade system."

Jan 1, 1983

By Robert B. Parsons

"While it might seem like heresy to suggest that ""taxation"" can be a source of financing, never the less some generous tax rules can considerably enhance the tax savings pertaining to a particular expenditure or project. A basic tax knowledge, and careful tax planning, can optimize government participation in a project. INTRODUCTIONIn trying to identify sources of financing for a project, ""government"" as a source of funding is normally thought of in terms of government grants, loan guarantees, interest rate buy downs, property tax waivers, hydro subsidies, and so on. Generally, such concessions are somewhat difficult to obtain, especially in the current period of apparent fiscal restraint. One source of government funding which should not be overlooked is the income tax regime, and, at the provincial level, the various provincial mining tax regimes.While the taxpayer would not normally view a tax system as a potential source of government financing, nevertheless various federal and provincial rules applicable to the mining industry can offer attractive tax deductions - and tax savings - with respect to particular expenditures. In fact, it is not unusual for a civil servant to refer to a tax deduction as a tax ""subsidy"". For example, in the right circumstances, the cost of a smelter expansion in New Brunswick would cost the operator only 31 cents on the dollar, with the federal and provincial governments paying for the other 69 cents by foregoing tax revenues (Table I). In a sense, such tax savings could be compared to a government grant equal to 69% of project costs. Of course, not every project expenditure will generate that degree of government funding. The fact of the matter is that the percentages of tax savings attached to different expenditures cover a wide range, depending on a complex mix of factors. The point to understand is that the tax rules can offer some valuable savings, even after tax reform, and that a basic knowledge of the tax rules can yield some fruitful rewards."

Jan 1, 1989

By D. Groenveld, M. Rozou

"Recent trends move towards automation, smart sensors, internet of things, powerful DCS, and more data. Are those trends already utilized in a real time production environment? Today operators still have to monitor several complex processes at the same time and predict their behavior based on an overwhelming amount of data available.The fact of the operator being overloaded and humans being unable to process multivariable problems shows the need of a tool merging essential data and providing consistent, sound decisions for long-term profitability.This paper shows a successful execution of ABB’s process improvement services in Aitik (Boliden SA), a copper mine located in Sweden. Soft sensors, fuzzy rule blocks and model predictive control were seamlessly integrated in the control system of the grinding area, resulting in proper control of mill loads and particle size without violation of any constraints.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations. The goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. It is also crucial to execute this process step at the lowest possible energy and grinding media consumption.An optimal grinding process controller must manage to maintain a given fresh feed level while keeping the product size within a given range without violating any constraints such as power, torque or load limits. To accomplish the aforementioned, it is necessary to manipulate the ore feed rate, water feed rate and the mill speed. The most significant disturbances adding another degree of complexity to this control problem are ore hardness and the amount of circulating load."

Jan 1, 2016

By G. T. Lapidus, O. J. Solis-Marcial

Currently, ores with high-grades of copper oxides and secondary sulfides have become increasingly scarce, which has encouraged industry to look for alternative raw materials to obtain copper. The problem is that primary sulfides are difficult to dissolve at near ambient conditions. Proposed hydrometallurgical processes have not been implemented beyond a pilot or demonstration scale. One of the principal disadvantages is that the majority of these processes are not viable with ores that contain less than 4% copper. One of the more recently proposed techniques involves the use of organic solvents in the dissolution of copper concentrates with a chalcopyrite content of between 20 and 30%, which has shown high efficiency. The present research explores the ability of this process to leach copper from low grade chalcopyritic ores (<4% Cu) at different temperatures ranging from 20 to 50°C. It was found that depending on the temperature, high percentages of copper were extracted in 40 to 100 minutes, using different oxidants. Additionally, distinct leaching behavior was observed with each oxidizing agent. In some cases, the extraction kinetics adjusted to the diffusion controlled shrinking core model.

Jan 1, 2014