Search Documents

Epicentres of recent shallow earthquakes in the region (3-12¦S, 126-150`E) were plotted to identify the various plate boundaries in the region, in particular the southernmost one marking the northern edge of the Australian plate. New and published fault plane solutions were examined to determine the style of faulting and state of stress along the Australian plate boundary. From east to west the boundary is first a subduction zone along the Solomon Islands, then a spreading centre across the Solomon Sea, a zone of compression and left lateral strike slip along the Papua Peninsula, almost pure thrusting across the centre of New Guinea and lastly left lateral strike silo through Irian Taya to the outer Banda Arc. The principal stress is very consistent, trending NW to NNW in a near horizontal plane, from the triple junction of the Pacific, Solomon Sea and Australian plates in the east to the Banda Sea in the west. Only along southern Solomon Sea plate margin which is a divergent boundary, is the stress different in type and direction.

Jan 1, 1987

By Dunstan N, Valentine C

Gas power was first used on the Sons of Gwalia mine in January 1911, when a twin-cylinder Crossley engine of 167 hp was installed to belt-drive a 112 kw 550-volt ac generator. This engine was connected with a No 8 Crossley up-draught suction gas producer, using mulga charcoal as fuel.A second Crossley engine, of 400 hp direct-coupled to a 550-volt ac generator, was installed in 1912, and operated by a down-draught wood producer.This was followed by a large Kynoch twin tandem four-cylinder engine, rated at 660 hp, sea level, with a rope drive to the crushing and treatment sections of the plant.These engines operated until January 1921, when the plant and power house were destroyed by fire. After the fire, both Kynoch and second Crossley engines were salvaged and reconditioned and they continued to give useful service for some years.

Jan 1, 1932

The karst water system in Han-Xing District is charaterised by heterogeneity in karstification and permeability of the limestone aquifer, unsteady flowing of the groundwater along karst runoff zone system, periodic recharge related with the periodic precipitation, and concentrative discharge of the groundwater in the form of karstic spring groups. The basic law is that the quantity of the water is very large during waterflood period and rather small in dry period, which has brought about difficulties and contradictions in mining and water supply. The measure to bring the karst water under control must be based on the principle of comprehensive ways and on the systems engineering method. Macroscopiclly, it is the reasonable countermeasure to retain surface water in the upstream section of the karst water system and to strengthen infiltration in the midstream section and to combine exploitation and utilization of the groundwater with water protection and mine dewatering in the area in which mines are distributed.

Jan 1, 1988

In an earlier paper(l) details of a laboratory method of extracting and separating tantalum and columbium oxides from tantalite have been given. In view of the fact that Australia may have need to be self sufficient in this field it was decided to erect a pilot plant for the production of tantalum oxide in the Metallurgy School, University of Melbourne. The plant was designed for treating about 40 lb. of ore in a batch over a period of two weeks, although; because of the sectionalized nature of the process, the capacity of the plant was 40 lb. ore per week.Australia is fortunate in possessing some very rich tantalite and columbite deposits, particularly in the Pilbara District in Western Australia. The ore used in this work was obtained from a small but high grade deposit near Greenbushes, Western Australia, and consisted of lumps, weighing up to 8 lb. each, of almost pure ferro-tantalite with occasional thin veins of the very' rare' mineral stibiotantalite.The main constituents were:

Jan 1, 1946

By Carrucan M. J

Costain Resources Limited operates two open cut coal mines in the Hunter Valley coalfields of New South Wales, Ravensworth Mine and Warkworth Mine. The location of the Ravensworth operation is shown in Figure 1. In the case of the Ravensworth Mine, Costain Australia is essentially a contract miner and is contracted to supply coal to Pacific Power (previously The Electricity Commission of New South Wales), on contracts won through a tender system. Due to the existing infrastructure and the lease area that associated with the contract, the mining strips at Ravensworth South have a maximum strike length of 1500 metres. This paper deals with the methods of scheduling used to overcome the challenge of mining the short strike length, multi-seam deposit at Ravensworth South.

Jan 1, 1992

By H. J. Glass, A J. Cornah

Improving the quality of the variogram helps to improve subsequent estimation and simulation processes. Two strategies for conditioning data prior to construction of the variogram are investigated using data from the Luce iron ore deposit in Canada. One strategy is the classic approach in which the deposit is subdivided into a set of structural domains. The domains are analysed individually and datapairs are recombined to produce a variogram. The second strategy is reconstruction of the deposit at an earlier stage of its history through unfolding. This involves transformation of the Cartesian coordinates into stratigraphic coordinate system. Improvement in the variogram quality, expressed in a decreased weighted deviation from a fitted model, is observed for both types of data conditioning. This indicates that, for the Luce deposit, application of data conditioning could also help to inform the selection of sampling locations.

Jan 1, 2006

By Miovski P, Hooft P. V

In the majority of recently commissioned gold mines granular activated carbon is used to adsorb gold from alkaline cyanide pulps or solutions. At the same time the carbon also adsorbs many other inorganic and organic species, most of which lower the activity of the carbon. Removal of these foulants is necessary before the carbon is reactivated and recycled. Standard practice for re- storing carbon activity involves high temperature treatment in a kiln - an apparently straightforward unit operation which is not always satisfactorily carried out. This paper presents the results of some fundamental work carried out on the thermal reactivation of carbon in a laboratory rotating pot kiln. The effects of temperature and steam addition on carbon activity were examined and compared with the activity of carbons obtained from a number of commercial kilns. Carbon was also reactivated using a small-scale Rintoul Furnace in which carbon was resistively heated by the direct passage of an alternating electric current. It was established that both elevated temperatures and the addition of steam to hot carbon generally enhanced its activity although peat-based extruded carbons responded a little differently to coconut shell types. Other measurements made included the weight loss and the hardness of carbons as a function of reactivation conditions.

Jan 1, 1987

By Marshall T, Nicholson DS

Reserves of high-grade quartz gravel, lignite and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while ooencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferro-silicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

Based upon specialised experience of rope mechanics spanning over 20 years, this paper reviews the processes of degradation and fatigue that are relevant to hoisting ropes in mines. The review is brought up to date with an account of the most recent work in this field, which identifies a torsional fatigue process and quantifies the impact of degradation upon the residual service life. A proper understanding of these processes is important in determining how different parameters of hoist design and operation interact to determine rope life. This knowledge is also important in informing decisions relating to rope discard based upon observed condition, as well is identifying the critical features that must be quantified reliably during inspection.

Jan 1, 2005

By Steinbrucker G

Improvements in mining by the application of electronics necessitates analy-sis of the objectives and problems. A detailed analysis has shown that increased tunel-ling performance is one of the most important objectives. In mining, the environmental conditions for machines, their handling and servicing are very hard. Therefore a health monitoring system for tunnelling machines in hazardous areas has been developed. This system measures operational parameters, such as-flow, pressure, temperature, etc., de-rives forecasts of possible failures from these values, and assists maintenance person-nel. Important data are transmitted to a surface computer via telephone cables. Health monitoring is based on the cognition that slow deterioration of characteristic parame-ters, e.g. fluid loss, are symptoms of wear. Sudden changes of machine parameters indi-cate sudden destruction. Computer technology is very advanced, but transducer technolo-gy has not,been able to keep pace. Filling the yawning gap in the mining industry is a challenge to technology and requires special techniques. Machine monitoring and automa-tion in underground mining is still in its infancy. A lqt of development and research work is still necessary. The risks are great-The expected benefit due to increased min-ing performance (up to 5 %) justifies the risks in development.

Jan 1, 1985

By Jones IO, Coles A, Austin D

This research project came about as a result of ICI Australia offering a scholarship to a final-year mining engineering student at the Western Australian School of Mines. A signifi-cant part of this year of study is devoted to an industrial project and consequently one of the conditions of the award is that the successful applicant pursue a research project of interest to the donor company.Having selected the project and the most appropriate final year student, a steering committee composed of representatives of ICI Australia, Kalgoorlie Mining Associates, the Mines Department and the WA School of Mines was set up. This committee is largely responsible for planning the main thrust of the research work whilst the detailed planning and day-to-day activities have been largely the responsi-bility of the research student, his academic supervisor and senior staff at the Mt Charlotte Mine.

Jan 1, 1984

The techniques used by the State Electricity Commis- sion of Victoria to handle and store brown coal in the both the raw coal and boiler bunkers are outlined. These tech- niques were adopted in agreement with the science of modern bulk solids handling. By successful balance between practical requirements and bulk solid handling system design require- ments the Commission expects to confidently attain reliable coal flow even for the most adverse of coal flow properties. Attainment of this goal demanded full attention to channel detail selection. An outcome of this attention has been the development of a novel bunker and discharge arrangement for handling extremely difficult to handle coals. Due to the novel features of this slot bunker outlet arrangement it's ad- vantages and disadvantages are discussed.

Jan 1, 1987

By Fermino R

Reduction of waste oxides from steel plant operations was investigated in a laboratory tube furnace at different temperatures and furnace atmospheres. The results have shown that the waste oxide pellets are reduced rapidly to very high degrees of metallization irrespective of the furnace atmosphere and that the reduction is simultaneously accompanied by significant low- ering of the original impurities. It is shown, for example, that treatment at 1000¦C for 30 min. can reduce the Zn content from 0.98% to 0.0065% and K and Na contents from 0.19% and 0.76% respectively, to less than 0.01%. However, pellet strength at 1000¦C was low but this, as shown in the paper, can be very significantly improved by treatment at 1250¦C. The results indicate that the reduction of the waste oxide pellets of this investigation proceeds almost certainly by a chain reaction mechanism and that this principle could be advantageously extended to the reduction of iron ores and other oxides in general.

Jan 1, 1984

By Masszi D

INTRODUCTION The association of methane with coal has been known almost since coal was first mined and in general it has been considered the curse of underground coal mining. Historically, most of the effort to handle this methane has been directed at diluting it to a safe level and preventing an explosive mixture of methane and oxygen from forming in any part of the mine. This is generally achieved by in-mine activites. This approach has two principal drawbacks, the severity of which are dependent on local conditions. The first is that the activity associated with the handling of the methane is undertaken in the mine and there- fore competes with the mining activity for the limited space available. The second drawback is that the whole methane handling activity is generally a cost to the coal because methane is so diluted that it cannot be used. With the value of energy increasing thi; second drawback is gaining importance so th.u several mines in Europe and North America ;it,, now installing systems to recover the methane in a useful form. Two approaches are

Jan 1, 1982

By M Roper, M Lovitt

WMC Resources Olympic Dam Operation located in South Australia, is a poly metallic underground sublevel open stoping (SLOS) mining operation with a current annual production rate in excess of 9.0 Mt. Stope size, geometries, geotechnical considerations, drilling and blasting are critical components in stope performance. These factors are further influenced by stringent ventilation requirements due to the presence of airborne radioactive contaminants from uranium mineralisation. Stope planning is complex and mass blasting methodologies have been trialled at Olympic Dam with the view to reducing the frequency of stope blasts, improving stope stability, productivity and ultimately improving overall stope performance. A key aspect in the ability to undertake underground mass blasts of this scale is the application of i-konTM electronic initiation technology by Orica. In the past two years in excess of three million tonnes has been initiated utilising this electronic technology, with an average blast of 250 000 t ranging to the largest to date being 580 000 t. By providing flexibility in blast designs, the use of electronic detonators has allowed mass firings over multiple sublevels. This has resulted in a significant reduction in stope extraction steps compared to conventional pyrotechnic firings. The benefits of this reduction in the number of stope blasts are wide ranging from improved stability of interim stope voids between blasts, reduced blasthole damage, improved blast vibration management and reduction of complex changes to ventilation systems for blasting.

Jan 1, 2004

**Add abstract here**

Jun 1, 2010

By P Fines, D J. Williams, G W, S Miller

This paper presents the results and findings of geochemical and mineralogical testwork conducted on samples collected from waste rock dumps at two mine sites, located in South Carolina, USA (Site 1) and Sudbury Ontario, Canada (Site 2). Important aspects of the relationship between the physical and geochemical aspects of the dumps are also presented. The overall aims of the project were to 1. determine if the physical and hydrological nature of the waste-rock dumps had any impact on the geochemical and mineralogical characteristics of the dump materials; and 2. to identify key implications for dump construction for ARD control. The results of geochemical and mineralogical tests indicate that the waste rock at Site 1 had undergone significant in-dump weathering and was relatively advanced with respect to ARD evolution. In contrast, the waste rock at Site 2 had undergone some weathering, however still contained a considerable amount of sulfide minerals. Testing also suggested that flushing of oxidation products at Site 2 had been limited, which therefore promoted the storage of oxidation products at the site. In addition, materials that had a D50 particle size in the range of 5 mm to 30 mm appeared to be more readily flushed than samples that had a D50 particle size of 30 mm. This suggested that preferential water pathways may have developed within the dumps at both sites.

Jan 1, 2003

Stressed steel cables, similar to those used in pre-stressed concrete, have been used for rock mass reinforcement, in civil engineering, for many years. This type of reinforcement has been attempted for open pit wall support, on several occasions, but has never gained wide acceptance as a practical approach because of high cost and complexity of installation in a mining environment. On the other hand, untensioned, fully grouted cable dowels (cable bolts) have gained wide acceptance for ground support in underground mining and it is perhaps surprising that this technique has not been used to a greater degree in open pit mining. The first systematic application of this technique in Australia was at the Mary Kathleen uranium mine in 1976, where it was spectacularly successful in maintaining steep stable walls in a jointed rock mass with unfavourably dipping structures. Cable bolting, and other techniques, are now being used to an increasing degree for wall support in both small and large open pits, for two basic applications: 1. stabilisation of potentially unstable sections of a wall, or 2. to allow steeper walls and reduce waste stripping volumes. In virtually every situation, wall rein- forcement has significant economic as well as technical advantages. The paper describes the development of the techniques, the mechanisms of wall support, the methods used, and discusses several case histories of its application to Australian open pit mines.

Jan 1, 1986

By D Morris

This presentation discusses a water filtration technology termed Fabric Media that is somewhat novel to the Australian market place and reports several recent mining industry installations. Like many novel household cleaning products, the Fabric Media technology applies the science of active washable micro fibres as the means of capturing contaminant solid particles. The simple Fabric Media water filtration product offers several attractive attributes when compared to the more traditional media bed filtration processes such as sand filters, and barrier filters such as micro membranes. A micro fibre based filtration media enables both superior adsorption for the contaminant and wash ability. Stronger adsorption capture enables a much higher flux and greater solids loading density for the filtration task, meaning that lower cost and smaller footprint equipment is available. For Fabric Media water filters, a textile weave is selected that minimises the flow backpressure for a given particle size separation. Thus for an equivalent filtration performance this provides a much lower operating energy requirement, generally between 50 and 80 per cent less than for a sand filter. A Fabric Media is not abrasive to itself or to the filter tank. The filtration performance remains constant and predictable. The equipment life is much longer and the asset value of the new filtration equipment should maintain throughout the project life. Fibres are extremely mechanically robust and chemically inert. Fabric Media survives repetitive exposure to a rapid mechanical washing event providing high wash efficiency with minimum equipment off-line time for the backwash. Dislodging captured contaminants by a high-speed mechanical agitation enables a minimum off-line time during backwash events. The vigorous backwash destroys adhering flocculant and eliminates the formation of mud balls, which can permanently foul sand filters. The mechanical agitation wash of the Fabric Media water filter ensures complete removal of grease and biofilm, which can adhere and block a membrane surface. In comparison to sand filters and micro filtration membranes, the Fabric Media product is applicable to a significantly wider range of solids concentrations without permanent damage. The technology is very forgiving to excursion in plant control and is therefore considered a very operator-friendly concept.

Jan 1, 2006

By Gallet M, Watsford R. M S

The 1989 feasibility study of the chessy, france, copper, zinc, pyrite and barite orebody was based upon a classical flowsheet. The flowsheet included, three stages of crushing, conventional rod and ball mill grinding in series, and sequential flotation of four products utilising conventional mechanical flotation cells. To improve the profitability of the project the partners commenced a search for ways to reduce the projected capital and operating costs of the proposed development. This paper presents the improvements in the projected capital and operating costs as a result of design and concept changes. The major changes included: ò the simplification of the crushing section with the adoption of semi autogenous grinding (SAG) milling of primary crushed ore. ò the deferral of pyrite and barite flotation circuits until market conditions were positive. ò the simplification of the flotation circuit by the use of column flotation cells for combined rougher/cleaner duty. ò the purchase of second hand equipment. The result of these changes was to reduce the capital cost estimate of the plant from US$ 21 million to US$ 11 million and operating cost estimates from US$ 18.90 to US$ 13.60 per tonne of ore for a decrease of approximately ten per cent in potential revenues.

Jan 1, 1991