Search Documents

A narrow (200-300m) zone of amphibolite facies metamorphic rocks underlies the Papuan ophiolite near the Musa-Kumusi divide, SW of Popondetta, Oro Province. The amphibolite rocks are bounded up-section, to the NE, by peridotite and gabbro of the ophiolite; and down-section, to the SW, by mafic greenschist, which in turn overlies blueschist facies mafic schists of the Emo Metamorphics.Amphibole compositions within the narrow contact zone show a strong chemical zonation which reflects a steep thermal gradient, with maximum temperatures >800¦C at the peridotite contact. The zonation is recorded in Ti content and A-site occupancy, relative to Al'¦

Jan 1, 1994

The Crown Minerals Act 1991 has introduced some significant changes to the New Zealand mining industry, not the least of which relate to the ability of miners to obtain access to land to conduct mining activities. This paper briefly reviews the relevant provisions of the Crown Minerals Act dealing with access arrangements, considers some typical features of access arrangements and examines a number of areas where problems may arise.

Jan 1, 1992

By K Matsui, R N. Gupta, H Shimada

Roof falls and failures of powered supports were major threats at longwall face. Abnormal geological conditions were caused roof falls and shield damage. Therefore continuous monitoring and analysis of strata behaviour was imperative on real time for forecasting adverse behaviour. Novel PXI instrumentation system was successfully developed for continuous monitoring and analysis of supports pressure, leg closure and gate roads convergence. However, this paper briefly examines the novel gate roads convergence monitoring system with field applications.

Jan 1, 2003

By Walker BV

Mining activity has been an integral component in the New Zealand economy since the early days of European settlement. Recently in common with other Pacific Rim countries there has been a resurgence of investment in gold. A sustained and increasing exploration effort has resulted in the rapid development of alluvial gold mining operations, a number of hard rock gold discoveries, and a general optimism about New Zealand's prospectivity. New Zealand's attitude to mining development, in particular hard rock gold mining is influenced by high environmental values and a concern, largely through absence of examples, that modern mining may not perform to community standards. While these environmental concerns are wide spread there is a growing realisation that gold mining, if properly managed, can take place within acceptable environmental standards and that it has the potential to contribute significantly to New Zealand's economy. New mining developments have an important role to play in this process. The mining industry in New Zealand is now at a crossroads. Having invested substantially and confirmed the potential for gold mining developments it has found itself in a rapidly changing economic environment as the Labour Government puts in place a number of fundamental economic reforms. The reforms are intended to free up the economy removing the rafts of subsidies and protective measures which have stultified initiative and growth. A fundamental reform of the public service has been initiated including corporatisation of trading activities and the establishment of a Department of Conservation to administer estensive areas of Crown land. Both petroleum and mining taxation are being reviewed with the intention of creating a more neutral competitive environment. Mining legislation is also being re-examined with both efficiency and equity objectives. While the current environment is characterised by uncertainty and rapid change, the outcome will be a more market-oriented stable policy environment, to the mutual benefit of the industry itself and the New Zealand Community.

Jan 1, 1987

It is proposed to deal with those raw materials which are produced in South Australia to meet the needs of the country's steel industry. They are chiefly, iron ore, limestone and quartz.Iron ore and limestone are fed to the blast furnaces of Newcastle and Port Kembla together with coke to produce the hot metal charge for the open hearth steel furnaces.They are also qsed in the raw state in the steel furnaces to assist in the conversion of the hot metal to steel. The iron ore is quarried from' Iron Knob and shipped from Whyalla to Newcastle and Port Kembla, whilst the limestone is supplied from the deposits at Rapid Bay and shipped in the same manner.Quartz is used in the manufacture of ferro-silicon, an alloy which is added to the ladles of molten metal tapped from the open hearth furnace in the case of almost every grade of steel. It is obtained from a quarry situated between Iron Knob and Whyalla, and shipped to Newcastle.IRON OREWith the exception of several small quarries situated at Breadalbane, Cadia, Cowra, Crookwell, Michelago, Jerrawa and lerraama in New South Wales, the iron ore requirements of Australia's steel industry to date have been met from Iron Knob and the Middleback Range in South Australia.Several of the small deposits in New South Wales were worked during the war years of 1941-44 during the shipping emergency and produced 1,355,417 tons, compared with an output of approximately 43,000,000 tons from Iron Knob between 1901 and 1949.

Jan 1, 1951

By Chappel R. A, Fishburn B. R

The Eastern Distributor Tunnels - the first major road tunnel project in Australia - are the preferred solution to traffic congestion problems, when compared with alternatives, in this inner urban environment. This is because of the reduced impact on residential housing, the improvement of the existing environment, less restrictions on future developments, and a reduction in noise and pollution. Developments leading to a tunnelled solution, traffic needs and reasons for route location are discussed. Criteria for design of tunnel alignments and geometry are described, including the restraints imposed by surface connections on profiles and grades resulting in low rock cover at tunnel portals. The main geotechnical restraints are a major weathered dyke at the shallow large span underground fork and the weathered Ashfield Shale capping the Hawkesbury Sandstone at a portal. Rock cuttability and excavation methods are discussed. Roadheader machines are the most suitable for the varying shallow arched cross sections required and the tunnel lengths involved but the use of blasting in special situations cannot be ruled out. Initial support for the major tunnel lengths will be provided by rock reinforcement in conjunction with shotcrete. Steel ribs are proposed in areas of low cover and weak ground. Final support will comprise an insitu concrete lining. Construction concepts and special tunnelling methods required at the shallow underground forks and tunnels are described.

Jan 1, 1987

By Komosa T, Muir D. M

Adequate levels of dissolved oxygen are essential for efficient gold dissolu- tion. The actual levels in plantpuips can be seriously reduced by the presence of oxygen consuming reactive minerals, and reduced oxygen solubility in saline water. The rate of gold dissolution is then limited by oxygen availability rather than cyanide. Ion selective electrode dissolved oxygen meters can give an effective indication of the relative oxygen saturation, but they are not able to give meaningful values of dissolved oxygen in saline water, without custom calibration curves. When the dissolved oxygen concentration is rate limiting, the addition of oxygen or peroxide can improve gold leaching kinetics as well as reduce cyanide consumption.

Jan 1, 1991

Upper Cretaceous and Eocene coal measures of the Ohai Coalfield are stratigraphically complex, and coal seam geometry and quality are influenced by washouts and partings resulting from accumulation in a fluvially active environment. Mining efficiency is influenced by these seam discontinuities, which are difficult to predict in the absence of refined paleoenvironmental models of peat accumulation. Petrographic variations between the Upper Cretaceous and Eocene coals indicate differences in the environments of peat accumulation. Seams in the Upper Cretaceous Morley Coal Measures accumulated autochthonously (in situ) in predominantly forest swamps with a high water table. These swamps were occasionally subject to brief floods. No significant changes in swamp vegetation, as indicated by petrography, have been detected between seams. In contrast, the greater content of mineral matter and maceral detritus within the Eocene Beaumont Coal Measure seams indicates hypautochthonous (locally transported) peat accumulation under more frequently flooded conditions. A precursor forest-moor is again indicated but the greater resin content of these coals compared with the Upper Cretaceous examples may suggest a greater contribution from conifers. Integration of coal petrography with investigation of other seam characteristics and coal measure sedimentology is expected to result in a detailed understanding of original depositional controls on peat accumulation. Paleoenvironmental models derived in this way should facilitate prediction of seam geometry, roof and floor conditions, and variations in coal quality, with obvious benefits to exploration and mine development.

Jan 1, 1983

By Harris RW, Wood BR

At any given time, the tidal force subjects massive regions to a spatially uniform load. The deformation of any large structure due to these forces is proportional to the elastic properties of the structure. In this aspect, the tidal force applies a load in a manner similar to that of a large-scale testing machine. Any anomalies in the measured tidal response must reflect alterations in the average elastic response of the massive structure. In the present work, tidal tilt measurements obtained in the wall of a large dam are used to infer changes in the response of the dam to applied loads. In particular, it is found that the dam response has changed by approximately 13 percent, on average, for two monitoring periods separated by 5 years. It is possible that these changes were produced by the different volumes of water in the dam for the monitoring periods. The tidal measurement technique can also be applied to monitor changes In the average structural response of large underground and surface masses relevant to coal and metal mines.

Jan 1, 1992

By Shonhardt JA, Bagster DF

This paper firstly examines the pollu- tion potential of burning colliery wastes. A comparison of two means of estimating the pro- pensity for coal to combust spontaneously is next presented. The use of microwaves, as a new procedure, is discussed in detail, while a comparison of the results is made with a modi- fied adiabatic technique. A number of coals that are known to combust spontaneously was tested, as were some coals that are not consi- dered to have self heating potential.

Jan 1, 1987

By J Araya, O Leiva

The mine evaluation process, composed of the designing, planning and valuation of a mine project, is, among other variables, based on an estimated orebody model. However, as the information from the drill holes is limited, it is impossible to know with certainty the mineral content in each block within the estimated block model. Consequently, uncertainty about the value of metal grades, or other geological attributes, arises because of the lack of information at unsampled locations. This is one of the reasons why, in any mine operation, there will always exist a divergence between estimated and real values. Cut-off grade optimisation is the process used to determine the operating mining strategy (long-term production scheduling) that will maximise the total profit value (normally referred as the net present value (NPV)) of a mine operation. This is done by defining a dynamic cut-off grade policy which is constrained by the production capacity of the mining, mill and refining.Real options is a type of contract, written on real assets such as mining, oil and other natural resource industries, that gives you the right but not the obligation to exercise the contract. It is based on operational and managerial flexibility, which allow mine decision makers to react to either good or bad operational and economic events in the future. But, what do geostatistics and cut-off grade optimisation have to do with the application of real options in a mine project evaluation process? The objective of this paper is to answer the previous question by showing how geostatistics combined with cut-off grade optimisation are key tools for corporate/managerial decision makers, which allow them not only to analyse the resource/reserves of their projects, but also to generate operational strategies that can maximise project value by minimising the downside risk due to ore tonnes and grade uncertainties, while achieving operational and physical constraints such as mining and processing capacities. A real copper grade open pit mine project is used as a case study.

Sep 26, 2011

By Lownds C. M

Several classes of commercial explosives and blasting agents behave non-ideally, especially in diameters near their critical diameter. A direct and convenient measure of non-ideal behavior is the detonation velocity (VOD); if the VOD is less than the ideal value, usually obtained by calculation, then the explosive is detonating in the non-ideal mode. Such lowering of the VOD is usually due to both lateral loss of energy and post-CJ release of energy. The second of these factors, namely slow release of chemical energy, is of most interest in blasting. While the observation of a low VOD clearly suggests slow reaction of part of the explosive composition, it does not necessarily mean that the energy is lost to the overall rock-breaking process. The partition of the energy of the explosive into various useful and wasteful categories is considered. Simple models of energy partition in blasting, and of explosive reaction kinetics, are presented. The models consider the effect of explosive type and rock type, the explosive being described in terms of the most common phases namely liquid, air bubbles, porous ammonium nitrate, dense or crystalline ammonium nitrate, and aluminum. Over a range of combinations of the above phases, the model predicts reasonable critical diameters and VOD's. Results are presented which show the effects of non-ideal detonation on fragmentation and heave in different rock types. Conclusions are drawn about those blasting conditions in which ideal behavior is beneficial, or Disadvantageous.

Jan 1, 1990

By Tucker G, Clark A, Young M. F, Johnston M

Mount Isa Mines has made a huge commitment to process control in milling. Yet in lead zinc we still failed to achieve a steady operation. Comparisons with manufacturing plants showed the key difference was failure to control plant inputs. Lead

Jan 1, 1998

By Singh TN

Rampura-Agucha Zinc-Lead deposit is unique as it is reported for the first time in the gneissic terrain with a rich oregrade quality of early to middle Proterozoic of Bhilwara supracrustal belt in the Precambrian of Northwest India. These sulphide ores are mostly confined to the graphite bearing Quartzofelspathic gneisses with intermittent bands of Calc-Silicate granofels and amphibolite. The ore and country rock mineralogy and their textural features are indicative of highly metamorphosed deposit and further the presence of marmatite and monoclinic phyrrhotite revealed high temperature environment of deposition.The present paper deals with some of the ideas about the ore genesis and petrographics of the associated rocks for Rampura-Agucha Zinc-Lead deposits of Bhilwara District (Rajasthan).

Jan 1, 1990

By Hefter G. T, Singh P

The use of sulphur dioxide (SO2) as an anode depolarizer in place of traditional oxygen evolution reduces the energy costs of copper electrowinning. This paper reports the effect of various metal ion impurities, which are usually present in th

Jan 1, 1998

Refractory gold concentrates and their roasted products have been examined by mineralogical and chemical methods, and the distribution of gold in the tailings after leaching has been Investigated.

Jan 1, 1989

Maintaining and improving the economics of open pit mining in the future requires understanding of the characteristics of open pit mining that are different to other mining or business activities, designing mines in the first place to be less susceptible to changes in these important characteristics, and adopting strategies which yield reliable returns despite unforeseen change. Planning and production personnel require guidelines and performance standards that are based on sound economics not solely on production criteria. The guidelines adopted for long-term implementation must assume a declining price for mineral products along with declining real costs, with research efforts directed at development of both evolutionary and revolutionary ideas aimed at implementation. Decision-making must focus on risk and probability criteria rather than just simple return-on-investment criteria, and the approach for management of personnel must support the higher level of communication essential for fast decision-making in the new environment of continual change.

Jan 1, 1992

By Corbett GJ

Comparisons between individual SW Pacific Rim gold deposits have facilit-ated proposal of a new classification of porphyry-related mesothermal gold deposit types. Carbonate base-metal gold systems form at relatively high crustal levels, peripheral to porphyry intrusions. There is a spatial assoc-iation with major structures which focus fluids from degassing porphyries at depth. Milled matrix intrusive breccias and extrusive maar volcano/ diatreme breccias form as a result of pre-mineralisation phreatomagmatic eruptions. These focus degassing magmatic fluids by the provision of fracture ground preparation, typically within competent host rocks, adjacent to the breccia bodies. Local dilational structures control the form of individual deposits which may contain bonanza gold grades at sites of fluid quenching and/or repeated mineral deposition.Early quartz veining and porphyry-related alteration is common and later gold mineralisation typically occurs in association with carbonate veining and Fe and base metal sulphides as Zn > Pb > Cu. The progressive cooling by mixing of the upwelling mineralised magmatic fluid with descending bicarbonate waters, produces characteristic zonations in carbonate compositions. These vary with distance from the porphyry source, from Ca through Mg, Mn and distal Fe types. Gold mineralisation is preferentially distributed within the Mn/Mg carbon-ates.

Jan 1, 1994

Bureau of Medical Inspection, Broken Hill, New South Wales.INTRODUCTIONFor a considerable time it has be3n realised that the pathological changes produced in human lungs by the inhalation of free silica varied, not only according to the amount of silica inhaled, its particle size and the period during which it was inhaled, but also according to other mineral elements which might be admixed with the fine silica dust and inhaled along with it, or inhaled subsequently to the silica containing dust. It was observed that, in many instances, these admixed dusts tended to inhibit the action of the free silica in causing injury to the lungs, as well as the development of certain complications, whilst in other cases it was felt that certain substances could actually accelerate the tissue damage caused by the silica.A fresh impetus to the problem of the prevention of the development of silicosis was given when, in 1937 and 1939, Denny, Robson and Irwin published papers entitled "The Prevention of Silicosis by Metallic Aluminum." Working at the same time at the Saranac La.boratory, and quite independently, and using a colloidal aluminum hydroxide, Gardner arrived at the same conclusions as Denny, Robson and Irwin, namely, that in experimental animals the development of silicotic changes could be prevented if eithertogether with the silica, or subsequent to its inhalation...

Jan 1, 1946

By Blair JR

The tunnel alignments investigated for the Gosford Regional Sewerage Scheme are located in the Terrigal Formation and are covered for most of their length by a thick blanket of soil and weathered rock. The following techniques were found to be most effective in geotechnical investigations for tunnelling in this area: air-photo interpretation, seismic surveys to pinpoint drilling targets, in-situ measurements of strength,deformation modulus and permeability in cored holes, and the construction of rock- mass models. Cross-hole seismic modulus measurements, surface resistivity soundings and electric well-logging techniques were found to have limited applicability due to adverse local conditions.

Jan 1, 1976