Search Documents

By Li YQ, Yoon RH

The photoresponse of natural mineral pyrite and galena electrodes has been studied in aqueous solutions on freshly fractured surfaces (some fractured in situ) using moderate overvoltages. When fractured in situ, the electrode potential of both minerals instantly drops several tenths of a volt. Pyrite exhibits a spontaneous anodic photocurrent at fracture, which indicates upward band bending (depletion layer) on the n-type electrodes. The negative surface charge responsible for the depletion layer is believed to arise from a surface state that is intrinsic to pyrite surfaces, possibly modified by hydroxide ion adsorption. The flat band potential, Vty, of pyrite is at approximately -1.0 V (SCE) at pH 9.2 but to reach V(b, pyrite has to be cathodically decomposed. In contrast, galena assumes the flat band potential at fracture. Subsequent polarisation of galena at potentials positive of Vth produces an anodic photocurrent (upward band bending) and polarisation negative of Vro a cathodic photocurrent. Most of the galena electrodes studied were degenerate n-type and at potentials negative of Vtb, no cathodic photocurrents are observed, indicating the bands cannot be bent downward, consistent with the Fermi level at the surface merging with the conduction band edge near Vn,. Several were close to intrinsic, with the photocurrent changing sign near Vn,.

Jan 1, 1993

By Scherbatsky VB, zon BM, Babushkin NM, Kitaev BI, Shabel&apos

The structure and hydrodynamics of the raceway zone of a blast furnace was studied on a cold model representing a sector containing two tuyeres. The model differed from the usual in that it was prov- ided with continuous flow of the coke layer at pre- determined rates, had provision for changing the tuyere parameters (diameter, protrusion, inclinat- ion) and irrigation of the layer with liquid. A combination probe was developed which per- mitted simultaneous measurement of the pressure field both across the area and through the height of the layer as well as determining the topography of the raceway. The velocity fields in the layer were measured with a specially made impulse thermo- anemometer. The determining criteria of the model were taken as the relationships between the energy of the blast and the particles, the dimensions of the raceway and the cross-section of the tuyere. The model established the effects of the tuy- ere structural parameters, blast parameters and amount of liquid products of smelting on the con- figuration of the raceway, the structure of the layer, pressure and velocity fields in the vicinity of the tuyeres and in the vertical direction through the layer. The properties of the raceway formation and the structure of the layer in motion have been clarified.

Jan 1, 1981

By Hendrix J. L, Nelson J. H

A study was conducted to examine how pretreatment of carbon-bearing gold ores with chlorine enhances gold recovery by cyanidation. It is hypothesized that metal species (including iron and copper) dissolved during chlorination adsorb on the carbon surface hindering the adsorption of dissolved gold. To test the hypothesis, samples of several sulfide minerals were subjected to reaction with sparged chlorine gas to determine which, if any, dissolve faster than gold under these conditions. Then, a synthetic carbonaceous refractory gold ore containing pyrite, chalcocite, activated carbon, and gold was subjected to gas sparging. The results of these experiments showed that chalcocite and arsenopyrite dissolve so that metal (copper and iron) is put into solution slightly faster than gold under the same chlorination conditions. Also, it was observed from the experiments that gold adsorbs on activated carbon during chlorination, but is replaced by copper and iron as the chlorination process dissolves more of the chalcocite and pyrite. The study concluded by investigating ferric chloride addition prior to chlorination to hinder gold adsorption on activated carbon.

Jan 1, 1991

By Gonzalez JM

The Pao gold prospect in N. Luzon, is an example of a high sulphidation epithermal gold system hosted in Mid-Tertiary alkaline volcanics, in the Philippine Arc. Styles of mineralization include: quartz-enargite veins, vuggy silica alteration bodies, and pervasive low grade (0.5ppm) gold mineralization, associated with kaolinite-pyrite-quartz alteration, and geochemically characterized by high As and Hg. Early magnetite-epidote-chlorite alteration linked to an unexposed granitoid is overprinted by an extensive zone of advanced argillic alteration (kaolinite-pyrite-quartz). No alunite is recorded. Important controls of mineralization include; a broad anticline intersected by axial faults, permeable pyroclastic units, and upward confinement of the alteration system by a highly impermeable, clay-rich volcanic unit. At this stratigraphic position the most important mineralization waz developed. The Pao high sulphidation system is not closely related to a stratovolcanic centre, and has formed subsequent to deformation of the volcanic field. It may, however, be related to an unexposed comagmatic intrusion.

Jan 1, 1990

The Olympic Dam smelter utilises Outokumpu Oy, flash smelting technology to produce blister copper direct from high grade copper concentrate.This paper describes the unit processes involved, including filtering/drying, materials handling, smelting, gas/dust handling, waste heat recovery, sulphur fixing, anode refining and casting.

Jan 1, 1993

Two ends of a longwall face are not only concentrated locations of equipment, but also provide ventilation and access. The roof strata stability here has an important influence on mining coal and safety. Based on field obser- vations in the gateways at Zaozhuang Colliery (Shandong Province) and model tests, the author developed a structural model of the overlying strata at the ends of the longwall face - the arc triangular cantilever plate - to which the elastic theory of plates can be applied. Factors influencing the stability of the cantilever plate and its breaking character- istics are discussed. Requirements and design parameters for supports at face ends are pro- posed, based on these factors.

Jan 1, 1986

By Wright D. C

The operation of the cyanide-sensitive Mintek/TB1 kegold electrode was studied in the laboratory, with regard to equilibration time and drift, the effects of pH, stirring, salinity, dissolved oxygen, zinc and copper(I) ions. Methods for valid calibration in the range 20-600 mg(NaCN)/L and pH values in the range 9 - 12 in the absence of copper were also studied. Increasing the salinity beyond a threshold of 40 g(NaCI)/L improves calibration and measurement. The sensitivity is 91 mV per decade change in the concentration of ionic cyanide, and output is reproducible to within 10 mV with attention to the factors listed above. However, salinity of 40 g(NaCI)/L also sensitises the electrode to interference by copper(1) ions. This copper sensitivity seems capable of saturation, suggesting a research strategy for possible remedies.

Jan 1, 1996

A simulation model of the load and haul process where the loader cycle has been subdivided into its individual components is used to consider the benefits derived from improved drill and blast methods. Field data from a Hunter Valley mine is u

Jan 1, 1998

By De Broglio R

The Mae Moh coal deposit was discovered some 60 years ago by villagers who noticed spontaneous combustion of coal outcrops. The first production began in the 1950's to fuel a fertilizer plant and a 12.5MW power station. During the period 1976 to 1979, three 75MW power station units were constructed on site. These have a total daily coal consumption of some 5000 tonnes and are served by a stockyard of approximately 60 000 tonnes total capacity. Stacked coal is reclaimed by means of a front end loader onto reclaim conveyors. During the years 1983 to 1986 four 150MW power station units were constructed east of the eastern seam subcrop, sons 2 km from the original power station complex. These have a daily coal consumption of nearly 12000 tonnes and are served by a stockyard of total capacity 270000 tonnes, equipped with two stackers and two bucket-wheel reclaimers for a totally mechanised system.

Jan 1, 1986

An understanding of the importance of the different components that comprise a rock bolt unit is necessary to ensure the proper use of rock bolts as a means of roof support. The various anchors, bolts and plates in use in Australia have been designed and adapted for Australian con- ditions. As mining conditions change, so will the types of bolts in use. This is apparent in the development of chemical anchors and other recent innovations.

Jan 1, 1971

Kamhalda is located within the Yilgarn Craton of Western Australia, specifically in the Norseman - Wiluna greenstone belt. Numerous nickel sulphide deposits have been mined at Kambalda with I I mines currently operating. For several years, a program of in-mine geophysics has been operating at Kambalda, with downhole electromagnetics (UHEM) one of the key techniques used. Three case studies illustrating the uses of UHEM in mines are presented here. In the first example, the Helmut South deposit was discovered as the result of an extensional exploration program. The first drill hole in the program intersected ore width and grade mineralisation at around 760 in depth. Two subsequent holes intersected subgrade mineralisation. DHEM surveys were completed in each of these three holes, with anomalies recorded indicating that a large conductor was located directly south of the first hole. The next hole intersected this target, for an intersection of 21.6 in at 3.5 per cent Ni. DHEM continued to play a role as the exploration program proceeded, providing drill hole targeting based on anomalous responses recorded in each drill hole. In the second example from Carnilya Hill, old drill holes were surveyed with DHEM in order to search a large section of prospective contact for massive ore pods. An off-hole anomaly was detected and subsequent mining discovered a small but high-grade pod of ore which was extracted for a considerable profit. Carnilya Hill has limited reserves and discoveries such as this, assist in keeping the mine operating. In the third example from Victor, a program of drilling intersected thin ore profiles in an interpreted flanking position. Without massive ore close by, these intersections probably do not constitute economic mineralisation. DHEM surveys of three holes did not detect any conductors. The area is now regarded as sterilised of significant massive ore and exploration efforts and dollars can be focused in other areas. These three examples demonstrate the type of successes that can he achieved through the use of DHEM.

Jan 1, 1997

By Enever J, Walton R, Wold M

Photoelastic and equivalent material model ling techniques for studying stresses and defor- mations and modes of failure in geological and engineering structures are described. The appli- cation of these techniques to the solution of tunnelling design problems is outlined. Models may contain heterogeneous components to simulate geological and man-made structures and may be two- or three-dimensional. Prototype construc- tion procedures and time dependent behaviour may be modelled. Examples of recent model studies carried out for the design of underground railway tunnels are given. Development of photoelastic and equi- valent material modelling techniques and facili- ties at the CSIRO, Division of Applied Geomech- anics are described, including a biaxial and triaxial frame for testing large scale two and three dimensional equivalent material models and components of full scale prototype structures.

Jan 1, 1976

Within the Mt Whaleback open cut mine the integrity of the final pit wall is achieved through careful rock slope design, use of rock reinforecement technology where marginal stability exists and use of controlled blasting techniques and excavation practices. By reducing the effective density of ANFO explosive within blastholes to around 0.2 glcm', and developing standard blast pattern designs for various rock types, blast damage to pit walls has been minimised. Accurate geological prediction is necessary for optimum blast design. Controlled blasting is undertaken where blasting occurs within 90 m of the designed final batter crest and hole by hole assessment of final limit blast patterns is undertaken before pattern charging. Shovels and trucks remove the bulk of blasted and dozed rock material, but due to the mine's variable pit wall slope configuration, bulldozer excavation of some critical design batters has been successfully Implemented.

Jan 1, 1986

By Evans A, Jones O

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialled the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, she specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tilts, and strains for rectangular panels and describe the sequences of ground movement from the mine roof through to the ground surface.

Jan 1, 1992

By Williams JK, Bolitho BC

Laverton Gold NL (Laverton) is the first junior Australian mining company to establish a viable mining operation in Indonesia. It successfully commissioned the Rawas plant in Sumatra this year with an average anticipated production of 85 000 ounces of gold equivalent (as gold and silver) per year, a feat of which Laverton is justifiably proud.Working in Indonesia and South-East Asia generally is very stressful for juniors and stretches human and financial resources to the limit - more so than in medium to large companies which can absorb the workload in-house more effectively.

Jan 1, 1997

In South African gold mines, the types of material requiring transportation to the stoping areas include timber packs, explosives, hydraulic rock props, scrapers, scraper winches, pipes, pumps and backfill material (in areas where backfill is being used). Currently timber packs are broken down to their basic components (log and brick) and are transported into the stope by means of either monowinches or a combination of monowinch and scraper winch. Other materials, such as explosives, hydraulic rock props, scrapers, scraper winches, pipes, pumps and backfill material must be transported by other means, usually by hand or, in the case of heavier items, by chain blocks. With the drive to increase stope advance rates and the rise in the number of miners with HIV/AIDS, there is a need in the South African gold mining industry for an improved material handling system. To meet future requirements, material handling systems should assist miners to transport materials quickly and efficiently. Furthermore, it must be financially viable and economically competitive with current material handling systems. This paper looks at the in-stope material handling efficiency of current monowinch systems and provides solutions to improve efficiency. In addition, the use of in-stope monorails are reviewed and the possible scenarios that will substantiate the use of monorail systems are discussed.

Jan 1, 2003

By Mason D. O, Tuckwell K. D

Whole rock geodhemical analyses from samples of Potosi gneiss within the Willyama Supergroup have been utilised to identify geochemical trends towards Pb/Zn ore positions. Although the analyses come from disparate sources they have been incorporated in the data base only if locational, sampling, analytical, lithological and stratigraphic descriptors were reliable. These data have been statistically analysed using programmes of the GASP software package. A discriminant function has been derived which permits Potosi gneiss associated with the Pb/Zn lode horizons in the Broken Hill domain to be distinguished from Potosi gneiss in a similar stratigraphic position in the Maybell Domain. In the "near ore" position the Potosi gneiss has significantly lower mean Na2O and significantly higher mean MnO. Also mean Rb, CaO and K20 are higher and mean Sr lower. This discriminant function serves to identify areas prospective for Pb/Zn mineralisation. A second discriminant function based on MnO, Si02 and K20/Na20 gives a semi- quantitative indication of proximity to ore.

Jan 1, 1983

By Corbett GJ, Leach TM

ABSTRAC'T' Although hosted within an Ordovician magmatic arc, the Peak Hill high sulphidation system displays features typical of younger Pacific Rim high sulphidation epithermal gold deposits. Regional NW trending transfer structures are inferred to localise the magmatic source at their intersection of the NS trending arc. Fluids have migrated from the magmatic source along NW structures and thence exploited permeable horizons, which have become silicified. Alteration displays typical zonation from silicification through assemblages characterised by alunite, pyrophyllite and kaolinite and is followed by breccia/fracture controlled sulphide and gold deposition. Sinistral rotation on the NS arc has dilated NW trending fractures to produce the WNW to EW dilational fractures which host the higher grade ore. Mineral assemblages are typical of formation distal to the magmatic source in an epithermal environment. The combination of alteration and mineralisation zonation with structure provide fluid vectors which target a magmatic source to the SE of Peak Hill.

Jan 1, 1995

By Houtgraaf M

The Far Fanning gold deposit is situated 60 kilometres south-west of Townsville (Fig. 1). Previous recorded production is 3756 tonnes returning about 1600 ounces of gold. This has been taken from surface and shallow underground workings- scattered over the strike length of the deposit of 1700 metres. The main production period was from 1895 to 1908.Previous exploration involving extensive trenching and sampling has been: carried out intermittently. since the 1930's, by Gold Mines of Australia (1932), Placer (1974), Anaconda (1975), Marathon (1980-8-1), Aberfoyle (1981-82), and The Northern Queensland Company (NQC) (1983-present).In 1980 Marathon undertook an extensive drilling programme to test the oxidised mineralisation. Over 200 percussion holes and- 7 diamond holes were drilled along traverse lines spaced 29 to 103 metres apart covering a strike length of around 1800 metres.

Jan 1, 1986

By De Carvalho J

The average installed refrigeration capacity on South African gold mines has increased by about eighteen per cent annually for the past 15 years; both the number of installations and their duties have increased. One consequence of these large refrigeration installations is that careful attention must be paid to the system for distributing cold water. In these distribution systems, devices which minimize the temperature rise of the water delivered to the underground workings and which also reduce the pumping requirements for returning the water back to surface are used. In this paper the suitability of these various devices are examined and with the aid of a specially developed computer program their optimum operating conditions are determined. In addition the optimum combination of surface and underground refrigeration plants is examined for a hypothetical mine at various depths and the importance of pump efficiency on total distribution costs is discussed.

Jan 1, 1988