Search Documents

By M Sykes

Gold was initially discovered at Ballarat in 1851. After initial alluvial mining, underground quartz mining commenced in 1853, continuing until 1918. The historic miners were considered to be capable of mining anywhere in the world after overcoming the difficult conditions within the Ballarat goldfields. Whilst mining has changed dramatically since the early 1900s the challenges with underground mining at Ballarat have not. Modern pumping systems cope with the moderate water inflows. However, modern machinery and efficient mining methods influence opening sizes and extraction techniques. In some cases modern techniques have accentuated the challenging ground conditions and complex orebodies that were faced by the historic miners. As the Ballarat East project has progressed towards production, technical challenges relating to geomechanics and mine planning are being resolved resourcefully.

Jan 1, 2008

By O Ishiyama, L Lu

Sintering is the most economic and widely used agglomeration process to prepare iron ore fines for blast furnace use. Due to the depleting reserves of traditional high-grade iron ore, there have been considerable changes in iron ore resources available throughout the world, especially in steel mills in East Asia. Corresponding to the changes in the availability of iron ore resources, the amount of impurities in iron ore has been slowly increasing. Some of these impurities have been found to have deleterious impacts on sinter quality and sintering performance. In the meantime, an increasing number of large blast furnaces with inner volumes of more than 5000 m3 have been built that require more sinter and are often more demanding in terms of the quality requirements of the ferrous materials. Finally, sinter plants are facing increasing pressure due to more stringent regulations regarding their environmental impact. This paper gives an overall review of a variety of technologies developed worldwide to tackle the changing raw material characteristics and mitigate emissions from sintering operations.CITATION:Lu, L and Ishiyama, O, 2015. Recent advances in iron ore sintering, in Proceedings Iron Ore 2015, pp 61–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Flatten, F Reusch

Recent advances in the disciplines involved in simulating large mining operations provide increasingly precise and accurate methods for the study of cave mechanics; however, in large regional-scale models, hydrological aspects are often neglected or studied independently from the mechanical problem. There exists a great demand for a unified approach to study and simulate both the mechanical and hydrological phenomena that allows for a more detailed understanding of the effects of groundwater flow, dewatering and the impact on block cave mining operations.This paper presents a numerical framework that combines three-dimensional regional-scale hydrological simulation techniques for groundwater flow, together with non-linear continuum–discontinuum rock mechanics models, provides such a unified modelling approach. The underlying simulation technique is based on a coupled parallel solution formulation adopting single-phase fluid flow formulations into a discontinuous, strain softening and dilatant finite element model. This approach is adopted for the presented case study of a realistic block caving example in a simplified unidirectional coupling formulation, to investigate the effects of the mechanical analysis on the hydrological response. Here, particular emphasis is on the non-linear coupling of the deformable and strain-softening solid skeleton and fluid phase; eg the change of hydraulic properties with evolution of damage in the rock mass and large-to-intermediate scale structures due to ongoing caving operations. The importance of discontinuum structures is discussed, as mining-induced fault reactivation significantly influences the hydrological response.CITATION:Flatten, A, Reusch, F and Beck, D, 2016. The application of hydromechanical mine-scale modelling for large block caving operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 341–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

BHP Billiton Olympic Dam produces copper cathode, uranium oxide concentrate and refined gold and silver. The operation is comprised of an underground Mine and Processing Plant and is located 560 km north of Adelaide. Water for the operation is sourced from two wellfields located 120 and 200 km from the operation in the Great Artesian Basin (GAB) at a rate of approximately 36 ML/d. Regulatory drawdown limits were established to protect regional GAB springs and are monitored at compliance bores. Drawdown was predicted in the æOlympic Dam Environmental Impact StudyÆ (Kinhill, 1997); however, pumping at higher volumes may have the potential for increased drawdown resulting in a trend towards the compliance limits. In recent years increased usage of water in the Concentrator and Hydromet sections of the Processing Plant has caused excess process water reporting to the Tailings Retention System (TRS). This has resulted in excessive amounts of liquor ponding on the tailings cells with a potential impact being contamination due to seepage of liquor to groundwater. Effective management of water by the operation is necessary to both reduce GAB drawdown and reduce the amount of liquor on the tailings cells. A site working-group has been established to investigate and pursue opportunities to improve the water use efficiency of the operation. This paper will highlight the issue of water management at Olympic Dam and discuss the various options currently being investigated to improve management of this important resource.

Jan 1, 2006

By Bidwell TJ, Servant S

Paste back-fill technology is gaining rapid acceptance in the Canadian mining industry. The authors were able to work on four different mining sites employing paste technology in their operation. In each site the paste hackfll is prepared with very fine tailings containing significant amounts of sulphur minerals. The research program involved laboratory testing on samples prepared in the laboratory, on control samples obtained at the hackfilll plant during pouring into the stopes and on core samples obtained from drilling in backfilled stopes. The laboratory testing provided detailed knowledge of the mechanical behavior of the paste backfill. The need for a means of measuring the in-situ mechanical properties of the backfill became clear. A review of various trials published in literature and an evaluation of available technology suggested the Cambridge Self-boring Pressuremeter. A first field campaign confirmed the efficiency and dependability of this instrument leading to the conclusion that it offers a very good method for the in-situ measurement of paste backfill properties.

Jan 1, 1998

By C Dell

Hillgrove, situated on the New England plateau of New South Wales, is an area rich in history and resources. Key resources are predominantly antimony, gold and scheelite and the area surrounding the historical field is environmentally sensitive and topographically challenging. Since acquiring the Hillgrove leases, Straits Hillgrove Gold has undertaken a significant exploration program on these historical mining areas with the goal to return the field to production. This exploration program has enabled Straits to significantly increase the resource base and has subsequently enabled the planned redevelopment of Hillgrove to be realised. In October 2006, installation of mining infrastructure and the initial stripping of existing development had commenced. To successfully redevelop Hillgrove, Straits has had to adopt a highly mechanised, trackless, diesel mining operation which will see the production rate commence at an initial rate of 250 kt/a of ore from a narrow vein environment. This ore will be processed on site to produce antimony metal, gold bullion and a scheelite concentrate.

Jan 1, 2008

By Just GD, Gillies ADS

There is an increasing need for reliable and comparable coal resource data and it is necessary to standardize the traditional classification procedures by quantifying the three basic evaluation criteria of economic feasibility, geologic assurance and recovery. For well documented deposits, geostatistical methods can consider- ably improve classification quality. A geostatistically based algorithm for classifying coal resources within the current Queensland and New South Wales codes has been developed. Application of the method in classifying resources from a number of seams exhibiting different structural characteristics is assessed. The method is found to give classification results which closely reflect the error associated with an estimate of resource quantities based on current sampling densi- ties. It requires a careful geostatistical analysis with emphasis on geological awareness. Resource category restrictions must be arbi- trarily assigned and remain constant for all deposits being compared. Engineering judgement is needed and interpretation may be required with isolated and peripheral blocks.

Jan 1, 1987

By D E. G Connelly, K Y. Wong

Gold at the Harbour Lights Mine (HLM), WA occurs principally in pyrite (Py) and arsenopyrite (AsPy) minerals rendering it inaccessible to direct cyanidation. Froth flotation produces a concentrate with low mass recovery and with high recoveries of sulfides. After investigating several alternatives, a novel flotation process has been developed to separate the concentrate into pyrite and arsenopyrite rich fractions. The pyrite fraction is finely ground and cyanide leached, while the arsenopyrite is treated off-site. This paper describes the separation process from laboratory bench scale through to commercial operation at the HLM gold plant.

Jan 1, 2005

By H von Blottnitz, J L. Broadhurst

Eco-efficiency has been proposed by the World Business Council on Sustainable Development as an environmental performance indicator framework that contributes to sustainability by assisting corporate decision makers improve the environmental performance of their operations and processes, while also extracting additional economic value. Given that the recent engagement of the minerals industry with sustainability has highlighted the need for requisite tools and methodologies, it is therefore of interest to assess whether eco-efficiency indicators can drive sustainability performance improvement during process design within the minerals industry. Previous work indicates that the choice of sustainability performance indicators to be used for decision making needs to be governed by the decision context; ie the performance indicators need to be fit-for-purpose. Here, the strengths and weaknesses of eco-efficiency indicators are analysed using case studies. First, a more rigorous definition of eco-efficiency indicators for the minerals industry is proposed based on indicators currently offered in the literature. Two case studies are then selected to reflect typical decision situations encountered within minerals process design. For each case study, eco-efficiency indicators are computed and are compared to more traditional graphical representations of the economic and environmental performance of process design alternatives considered. The sensitivity of these indicators to various process design parameters is also investigated. Results confirm that the meaningful application of eco-efficiency indicators is strongly dependent on the decision context in which the process data is generated. Results also show that eco-efficiency indicators can be related to technical process design parameters to allow for richer communication of performance information for various decision trade-offs; however, in some cases, graphical approaches that provide more insights into the environmental-financial trade-offs should be preferred. The research thus contributes to guiding the selection of the appropriate tools for more environmentally sustainable design of minerals beneficiation processes.

Jan 1, 2009

By D Capstick, M B. Ebell

This paper describes the test work, process design, commissioning and operation of a processing system at the Ergo gold operation that improves the extraction efficiency from gold tailings material. The improvement in recovery is derived from the separation of the gold contained within the sulfides of the tailings material and a dedicated process stream to recover that gold.The sulfides are separated by means of a flotation circuit and that resulting concentrate is subjected to a regrind of below 20 ¦m to enable a greater liberation of the gold. The ultra-fine material is then subjected to a dedicated leach circuit to recover the now exposed gold particles.The case study is an example of the challenges of introducing new technology and methodologies to a well-established operation and thereby attaining improved efficiencies and tangible business benefits.CITATION:Ebell, M B and Capstick, D, 2013. Improving extraction efficiency from Witwatersrand gold tailings using flotation and ultra-fine grinding of concentrates, in Proceedings World Gold 2013 , pp 301-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By D Henderson, M Germain

The beneficiation of iron ore deposits to yield haematite and magnetite concentrates for steel making processes typically require the use of one or a combination of wet processing techniques based on gravity, magnetic or froth flotation processes. With the need for more cost-effective technologies with a lower water demand, a re-examination of dry processing techniques has been initiated. For example, a dry processing capability may offer an advantage where suitable quality and quantity of process water hinders the development of a particular resource. This paper describes recent laboratory test work for the production of high grade concentrates using dry electrostatic techniques for -300 ¦m haematite and magnetite ores and compares them with magnetic separation techniques.

Jan 1, 2009

By J Palise

As cities become more populated and the need for tunnelling increases, we continue to dig deeper urban tunnels in more challenging ground conditions. At the same time our expectations for durability and long-term performance are increasing.It has become increasingly apparent in recent years that repairing water leaks in tunnels can be very costly and unplanned infiltration can cause undesirable outcomes for long-term maintenance costs, structural durability and environmental impacts. For this reason, tunnel constructors are investing more time and effort upfront into drainage and waterproofing systems.Tunnel membrane systems are becoming accepted as a necessary part of tunnel construction, however the knowledge surrounding selection of appropriate systems, design detailing and installation methods has not increased at the same rate. Currently Australia relies heavily on International Standards from Europe and the United States with no immediate program in place to establish our own locally relevant industry standards.This paper gives an overview of where the industry in Australasia is heading in terms of adopting relevant standards. Current basic waterproof detailing options for drained and undrained tunnels with success and failure of various methods are also addressed. Finally we look at the Brisbane Airport Link as a case study for how tunnel waterproofing contract methods, design and installation issues are being addressed in context with recent projects including the Epping to Chatswood Rail Link in Sydney, Auckland Northern Gateway Tunnel, Eastlink Tunnel in Melbourne and Sydney City West Cable Tunnel.This paper’s primary objective is to propose guidelines for how tunnel waterproofing could be implemented on large infrastructure projects in the future and to map a path for preparing and introducing a ready to use document for selecting appropriate tunnel membrane and drainage systems whilst implementing detailing methods which are appropriate for local conditions.

Mar 8, 2011

By R Thompson, D Tulloch

"Wet-weather or 24×7 wet-trafficability is a commendable design objective for unpaved mine haul roads, but practically often difficult to achieve, due both to the road sheeting material selected, and also its breakdown under the action of traffic and environment. Accidents allied to wet-trafficability issues, either due to rain or often more commonly, over-watering of mine roads, is increasing and especially the loss of control or uncontrolled vehicle movements categorisation. The dominant system failure is that once vehicle control is lost, control cannot be regained.The friction supply, or ‘skid resistance’ of a mine haul road sheeting is critical to the safe operation of the road and data has to be collated concerning the variation of friction supply with sheeting material engineering or indicator properties. In the light of the paucity of data existing in this field, this paper presents the contributory research that informs the development of improved and validated unpaved mine road friction supply estimates, based on a number of mine site evaluations across a range of sheeting material types and characteristic parameters, leading to improved predictive models of friction supply.Results from this preliminary review will enable operators to assess their road sheeting materials, improve and validate unpaved mine road friction supply estimates. This will contribute to improved road design, management and 24×7 operability decisions and contribute to a reduction in heavy vehicle loss of control incidents on gravel-surfaced mine haulage roads.Citation:Thompson, R and Tulloch, D, 2016. What's Stopping You? The Role of Sheeting Material Selection in Safe Haulage Operations, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 253–264 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By W D. Ortlepp

Seismicity associated with deep block cave mining operations in hard rock can give rise to dynamic loading of the mining openings. A description is given of the source and damage mechanisms associated with such seismic events, and the possible demands placed on the rock support by the resulting dynamic loading. In addition, production level drifts are often subjected to large static deformations during mining. Appropriate support, able to sustain large static deformations, and capable of absorbing the energy released during dynamic loading, is described. The performance of these support types has been determined by means of large-scale dynamic loading tests, and large deformation static laboratory tests. Finally, a support system which is considered to be appropriate for extraction drifts in block cave layouts subjected to dynamic loading is described.

Jan 1, 2000

By B Murphy, J L. Heath

Installation of flotation equipment is a lengthy and intricate process involving conceptual design, detailed design and layout, equipment installation, equipment commissioning and handover prior to the plant commencing operation. During these steps, mistakes are often made that lead to increased costs and/or schedule delays in bringing the new equipment online.This paper presents a series of recommendations for the installation and commissioning of flotation equipment to minimise mistakes and ensure that plant production commences efficiently with a minimum of resources. The advice herein is based on lessons learnt from recent flotation equipment commissioning. It is intended as resource material for flotation plant designers, construction contractors, metallurgists and operators, and is applicable to both new and existing plants.CITATION:Heath, J L, Murphy, B and Bourke, P, 2014. Effectively installing and commissioning flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 399–404 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By T M. Nester, D J. Reardon, A N. Page, B J. Barsanti

The load capacity of a friction bolt has long been regarded as 4 t/m of embedment for ground support design analysis and supported by in situ pull test results. In recent years, the authors have observed lower pull test results or inconsistent results which were rarely sighted in the early 2000s. The lower pull test results indicated in some cases that reliable friction bolt capacity (≥90 per cent of results) is closer to 3 t/m of embedment with some geotechnical engineers adjusting the ground support parameters in the design work accordingly. This can be in contrast with other mines which reliably obtain 4 t/m (or greater) using the same suppliers bolt in similar ground conditions. This raised several questions: • What is the effect of poor installation (bolt twist or bolt hole deviation)? • Does the performance of friction bolts vary in different rock masses? • Does bolt performance vary between suppliers? • What effect does increased jumbo feed/percussion/rotation settings have? • Have the bolt dimensions or steel strip width changed? • Have the physical bolt properties changed? • Have the steel properties changed? This paper was aimed to answer as many of these questions as possible and discuss each variable in detail. This project included friction bolt trials at various mine sites across Australia, multiple friction bolt manufacturers, steel manufacturers and laboratory analysis. The paper also includes discussion on what the authors consider best practice for pull testing. It should be noted, the terms ‘friction stabiliser’ and ‘split set’ used in this paper are used in a generic manner and is not linked to any specific ground support supplier. Whilst its acknowledged within the industry the term split set and friction stabiliser is used interchangeably, the authors acknowledge that the term split set is a trademark of Split Set Mining Systems and has been used in context in this paper.

Nov 29, 2022

By A Holmgren, W Forsling

In the present study infrared attenuated total reflection (IR-ATR) was used to monitor the rate of in situ adsorption of heptyl xanthate on a layer of zinc sulfide synthesised on a germanium ATR crystal. The zinc sulfide surface was characterised using x-ray photoelectron spectroscopy (XPS). The absorbance of heptyl xanthate measured increased with increasing bulk concentration of the adsorbate up to an equilibrium plateau value corresponding to a fractional coverage of the surface sites of the substrate. For the adsorption from solutions of concentrations between 10-3 and 10-5 M, the rate of adsorption increased with increasing bulk concentration. At higher concentrations the measured absorbance should be corrected for the absorbance due to the concentration of xanthate in bulk solution. The present work provides a discussion of this correction. Assuming the adsorption stage to be rate-controlling and proportional both to the concentration of the adsorbing species in solution and unreacted surface area, a rate law governing this type of transient adsorption kinetics was derived. By means of absorbance data for the concentrations 0.1 and 0.01 mM, the rate constant of adsorption was calculated. From the initial part of a Langmuir adsorption isotherm, the absorbance at monolayer coverage and the equilibrium constant of adsorption could be estimated.

Jan 1, 2005

By A Jakowetz

OxianaÆs Sepon Copper Operation (part of the combined Sepon Gold and Copper Operation) is located in Savannaket Province, in southern central Lao PDR. The site is relatively remote, being some five hours inland from the Laos/Thailand border crossing on the Mekong River. The copper processing plant was designed to treat 1.3 Mtpa ROM ore to produce 60 000 tpa of copper cathode. Commissioning of the processing plant was completed in mid March 2005 with ramp up completed in January 2006 with 5260 tonnes of cathode harvested in this month. The focus of this paper is on SeponÆs unique grinding circuit. The entire grinding circuit is operated at highly acidic conditions, adding a number of different operational issues over and above those normally associated with grinding circuits. It became evident early in the ramp up, that reaching design mill throughput of 170 dry tonnes per hour with the original design would be challenging, coupled with the realisation that ceramic grinding media consumption had been underestimated. In order to lift the overall throughput of the processing plant, a significant continuous improvement process has been implemented within the grinding circuit to lift this key unitÆs production capacity. This presentation will focus on the key areas that have been addressed in the 12 month ramp up period and highlight areas for future work. Results to date have shown this improvement process to be very successful, with throughput rates in excess of 200 tph regularly achieved.

Jan 1, 2006

By J. K. A. McLEOD

Address by the President of the Institute (Mr J K A McLeod) in presenting the Institute Medal to Howard Knox Warner, C.B.E. Address by Howard Knox Warner after accepting the award.

Jan 1, 1978

By N Tyson

Throughout Australia and the world, there have been in recent years a number of incidents involving the reaction of ammonium nitrate based explosives with ground containing certain types of sulphides. This paper presents a comprehensive strategy designed to identify, assess and mitigate the risks involved with blasting in areas of reactive ground. Undertaking blasting in reactive or potentially reactive ground involves a degree of risk, the level of which is dependent upon the controls in place for specific sites; this in turn depends upon the degree of sound reasoning and judgement behind the implementation of these controls. Implementation of controls to minimise the risk of incidents also involves a measurable increase in production and blasting costs. To achieve a balanced solution to this matter, decision-makers need to understand how the risks eventuate, how they should be evaluated, and how control measures reduce the risk. Also required is an understanding of how the problem affects the economics of the operation, and the magnitude of this effect. It is the aim of this paper to provide a structured approach to gaining this knowledge, so that mine management, the workforce and explosive suppliers may jointly develop more effective economic and safe blasting systems for potentially reactive ground. Using a combination of fault/event tree risk assessment and semi-quantitative analysis, a structured approach to dealing with the issue will be illustrated.

Jan 1, 2001