Search Documents

By R. B. Burt, James A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1-the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2-power required for pumping, 3-pump selection. The basic factors for a given problem will include: 1-weight per unit of time of solids to be handled, 2-specific gravity of solids, for calculation of volume, friction and power, 3-screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4-shape of particle or some means of determining a friction constant, 5-effects of percentage of solids, 6-development of a viscosity factor to be used in the overall calculations, 7-calculation of the lower limits of pipeline velocities permissible, 8-calculation of total head, pump horsepower, and 9-setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble, phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; -14 +35 mesh, 11.4 pct; -35 +150 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The -150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble, content of the matrix, i.e., the +14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum -velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is, smooth and- polished because of the scouring, action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump, changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1952

[Furnaces (see also Blast jurnaces) :-(Continued.) McGill, Nev., LI, 765. roasting: XLIX, 184, 188. Anaconda, Mont., XXXVII, 462, XLIX, 676. concrete hearths for, XLVI, 419. Crouse, XLVI, 413. gas, XXXVIII, 163. Heberlein, XXXVII, 634.]

Jan 1, 1918

By John T. Awald

The Bradshaw Mountains of west-central Arizona cover an area of 1600 square miles and contain numerous old mines and prospects. The area has been geochemically sampled on a reconnaissance basis to relate mineralized areas to regional structure and rock types. Copper analyses of stream sediments have been classified and contoured to show the distribution of low and high backgrounds and low, intermediate, and highly anomalous areas. Contoured results are compared to geology and known mines. Several prospecting areas are indicated.

Jan 1, 1972

By George K. Burgess

The suggestion has often been made that it would be highly desirable, at least for certain grades of steel, to be able to control more certainly, by pyrometric measurement or otherwise, the temperatures of the operation of the open-hearth and other furnaces used in the manufacture of steel and iron. That the properties of the ingot and finally of the finished steel product are intimately related to the final temperatures attained by the metal in the furnace and to the temperature of casting, has been recognized by metallurgists for a long time, and this question has been very thoroughly treated, especially by Prof. Henry M. Howe, and by A. W. and H. Brearley.1 It is the object of this paper to demonstrate that in so far as casting temperatures of furnaces, steel ingots, and similar operations involving the temperatures of streams of iron and steel are concerned, well-known pyrometric methods may be easily applied—if certain recently determined corrections are made and precautions taken—with a relatively high degree of accuracy. Greater but not insurmountable difficulties will be encountered in the case of open-hearth furnace temperatures, while for those of the converter type a ready solution does not seem practicable. It appears that certain essential data have always been lacking in reporting observations such as those of Le Chatelier in 1892. Thus the correction to be applied for the characteristic radiation—or emissivity— has hitherto not been adequately taken into account nor the limitations of the several possible pyrometric methods clearly recognized. In view of the fact that in open-hearth practice the temperature to be measured in the furnace itself, in the stream of metal and slag and in the teeming into molds or ingots is usually above 1,500" C. (2,700" F.)

Jan 1, 1917

A development drilling and bulk sampling program should furnish the following information: (1) geology of the mineralized zone, (2) quantitative data on grade and tons of material within pertinent cutoff limits, (3) physical size and shape of the deposit and areas underlain by waste as well as ore, (4) mineralogical and metallurgical characteristics of the ore, (5) physical characteristics of the ore, (6) bulk samples for metallurgical testing and grade, (7) data on factors that affect mining operations, such as ground water and ground conditions. The method and equipment best suited for a particular drilling job depend upon the geologic features of the mineral deposit to be tested.

Jan 10, 1967

By H. A. Bedworth, W. H. Bassett

The amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors' laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hampe1 that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe's method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen. Heath4 found that the loss in weight after heating in hydrogen did not represent the true oxygen as cuprous oxide but included also gases derived by the metal from the fuel and refining in the furnace, and any trace of mechanically held moisture. He found, further, that the copper after ignition retained hydrogen equivalent to about 0.01 per cent. Heath proposed to determine the amount of occluded gases by preliminary ignition for 20 min. in pure carbon dioxide—and to correct the error caused by absorbed hydrogen by subsequent ignition and cooling in carbon dioxide, finally replacing this gas with air.

Jan 1, 1926

Jan 1, 1952

America.-Foreman, J. T. Ashland.-Sturdevant, J. C. AItalIa. Henderson, R. M. Bessemer.-Ball, E. M. Maschmeyer, W. L. McKenzie, W. C., Jr. Birmingham.-Abbott, C. E. Aldrich, T. H. Aldrich, T. H., Jr Aufderhaar, H. C. Berg, H. A. Blair, C. S. Bush, M. W. Clark, G. H.

Jan 1, 1923

By J. W. Spretnak, G. Sachs

The: iron-rich iron-nickel alloys have attracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are the base of many alloys with various outstanding properties. The iron-nickel alloys, therefore, have been investigated extensively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,l and will be discussed in some detail in the sections of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to 10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis," which is not dependent upon the rate of cooling and persists even with very slow rates of cooling.3 Honda4 and Merica4 have therefore resigned themselves to proposing a diagram (Fig. I) for practical use, illustrating the structural relations under commercial conditions instead of attempting to establish the true equilibrium diagram. Marsh is less pessimistic and suggests an equilibrium diagram (Fig. 2) which conforms approximately to the facts known about this system. Recent X-ray investigations by Owen-Sully5 and Bradley-Gold-schmidt6 on powdered alloys indicate that the previous work on the iron-nickel system yielded very incomplete results. These investigators agree (Figs. 3 and ,+) that alloys in the powdered form containing more than 8 per cent and up to about 35 per cent Ni decompose into a stable heterogeneous mix-

Jan 1, 1941

By G. Sachs, J. W. Spretnak

The: iron-rich iron-nickel alloys have attracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are the base of many alloys with various outstanding properties. The iron-nickel alloys, therefore, have been investigated extensively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,l and will be discussed in some detail in the sections of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to 10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis," which is not dependent upon the rate of cooling and persists even with very slow rates of cooling.3 Honda4 and Merica4 have therefore resigned themselves to proposing a diagram (Fig. I) for practical use, illustrating the structural relations under commercial conditions instead of attempting to establish the true equilibrium diagram. Marsh is less pessimistic and suggests an equilibrium diagram (Fig. 2) which conforms approximately to the facts known about this system. Recent X-ray investigations by Owen-Sully5 and Bradley-Gold-schmidt6 on powdered alloys indicate that the previous work on the iron-nickel system yielded very incomplete results. These investigators agree (Figs. 3 and ,+) that alloys in the powdered form containing more than 8 per cent and up to about 35 per cent Ni decompose into a stable heterogeneous mix-

Jan 1, 1941

By B. W. Prof. Frazier

(Read at the Wilkes-Barre Meeting, May, 1877.) THIS interesting application of the laws of thermodynamics to metallurgical practice has not been discussed by any writer, within my reading, except the late Prof. Gallon of Paris. In his Cours de Machines,* Prof. Callon has given a short but lucid discussion of this subject in the admirably clear style for which he was remarkable. Although the interest attached to the subject is rather theoretical than practical, I have thought that an attempt to explain the mechanical action exerted in the hot-blast oven might not be entirely devoid of utility, especially in the suggestions which it involves. The statement, that the mechanical work performed in heating the blast is, when high temperatures are produced, considerably greater than the work performed by the blowing-engine, may seem incredible to many who are practically acquainted with the subject, appearing, as it does, to conflict with the results of their experience. It is, nevertheless, literally true, and I shall attempt in this paper to prove it, and to explain why it has not rendered itself palpably manifest in practice. Before proceeding to the mathematical demonstration, it will be well to recall to mind the definitions of some terms employed by writers in mechanics and thermodynamics. The actual energy of a moving body, as defined by Rankine, is the work which it is capable of performing against a retarding resistance before being brought to rest, and is equal to the energy which must be exerted on the body to bring it from a state of rest to its actual velocity. The value of that quantity is the product of the weight of the body into the height from which it must fall to acquire its actual velocity. * Vol. I, chap. x, [§ ] 4, p. 312.

Jan 1, 1878

By James J. Bailey

Percussive drills have been in commercial use for many decades. Until relatively recently there was little serious effort to analyze the stresses in such devices in any detail. Within the last few years such analyses have been developed and have been reported by a number of authors.1-4 We present here an investigation of the impact systems of a family of conventional down-hole drills with optimization the objective. We have assumed that maximum drilling speed was the quality most desired and that this was to be achieved within conventional practice. In fact the methods that are demonstrated in principle below can readily be adapted to other percussive devices, whether conventional or not, and to other constraints. SOME PERFORMANCE PARAMETERS FOR PERCUSSIVE DRILLS Consider a percussive drill with an air motor operating with the following parameters: p-supply air pressure a-effective piston area W-piston mass S-piston stroke If we consider a simple (constant pressure) cycle, the following relationships can be derived. The blow frequency [N~ pa lie WS 377]

Jan 1, 1968

By Bernard H. Coyle, Robert N. Anderson, Judith A. Koperski

Between 6 and 8 million cars are shredded annually in the U.S. This shredded material is magnetically separated leaving a mixture of nonmetallics and nonferrous metals which can be further separated into its metallic and nonmetallic constituents. The metallic portion is a mixture of metalr; and alloys containing predominately zinc, and some aluminum, copper, and residual iron. Hydrometallurgical strategies are proposed for recovering the aluminum, copper, and zinc. The thermodynamic and kinetic behavior of the most promising alternatives to separation are discussed.

Jan 1, 1978

By P. T. Carter, A. B. Murad, H. B. Bell

N. A. Gokcen (Michigan College of Mining and Technology, Houghton, Mich.)—The activities of silica, represented in Fig. 5 for the systems MnO-SiO2 and CaO-SiO2, are in disagreement with the established binary phase diagrams. At Ns102 = 0.50 in MnO-SiO2, and at Ns102, = 0.65 in CaO-SiO2, each binary system is saturated with respect to silica at 1550°C, and therefore as102, is unity in each case. The curves for as102 (FeO-SiO2) and as102, (MnO-SiO,) should nearly co-

Jan 1, 1953

Cycle, automatic, in mine hoists, LV, 17. Cylindrical furnaces, repairing partly collapsed, XXXVI, 215-222. Dacite-porphyry, San Jose, Tamaulipas, Mex., percentage composition, XXXVI, 186. DAGGETT, ELLSWORTH: The Extraordinary Faulting at the Berlin Mine, Nev., XXXVIII, [liii], 297. Daiquiri, Cuba: geology, LIII, 3, 43. iron deposits, LIII, 40. Magdalena mine, LIII, 9, 23, 24. mines, bibliography, LIII, 59. situation of mines, LIII, 42. [ ]

Jan 1, 1918

By O. E. Kiessling

A GROWING uneasiness in the oil fields indicates that doubts are arising as to the efficiency of the present technical, economic and legal arrangements affecting production. Recent documents of the federal government, debates in state legislatures, editorials in the daily press and statements of oil company executives re-echo the notion that the present methods of producing oil satisfy neither the business man nor the public. Such intimations are of utmost importance, since oil is a vital clement in modern industry and dependence upon it increases as new uses develop. SECTION I-PRESENT SCHEME OF COMPETITIVE EXPLOITATION IS WASTEFUL The oil industry has convinced itself, for very good reasons, that the present scheme of competitive exploitation results in losses, both in terms of quantities of oil and in terms of profits. The story of these losses is familiar enough, and it is necessary only to distinguish and summarize briefly certain factors that are of importance to the following argument. Oil pools are exploited under a competitive economic system based on private ownership and contract; the hope of profits attracts capital and enterprise, and competition is supposed to serve as a regulative factor. Whether such a scheme of industrial organization works is partially dependent on the ability of the producer to withhold or produce is commodity as he sees fit, in accordance with the dictates of market demand.

Jan 1, 1927

By H. E. Mussey

WHEN the American Institute of Mining Engineers visited the Birmingham district in May, 1888, the four Ensley furnaces (Fig. 1) then FIG. 1.-BLAST-FURNACE DEVELOPMENT IN ALABAMA. completed were referred to as monumental.1 Their dimensions are given in Table 1. Mr. Gordon stated, with considerable satisfaction, that on the preceding day one furnace had produced 165 tons. The blast was

Jan 10, 1924

By B. Ball, C. H. Cox, S. N. Yap

Electrokinetic measurements on cassiterite were made in the presence of sodium di-hydrogen phosphate, mono-hydrogen arsenate, bisulfite, and sulfate. Flotation studies were also conducted using sodium dodecyl sulfonate in the presence of these salts. It was found that the anions specifically adsorb on cassiterite in the order H2AsO-4 H2PO4 HSO3 SO4 and consequently cause flotation depression. The adsorption mechanisms of the various inorganic anions are discussed in detail.

Jan 1, 1980

By W. H. Bassett

A 10-year, sea-water, corrosion test of tubes of several copper alloys has shown that many alloys withstood attack by solution, pitting, and dezinkification; a 1-year, salt-spray test of sheet-metal specimens of the same composition showed the same results. THE late J. P. Sparrow, chief operating engineer of the New York Edison Co., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in' September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40, 70-30, 80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period.

Jan 1, 1925

MINING, to be precise, ends when the ore is delivered to a bin outside the mine. Usually the next step is concentrating; or, as it is more often called, milling. A few elementary definitions will help make clear the discussion that is to follow. A rock is an aggregate of minerals; copper ore is rock that contains copper-bearing minerals in quantity sufficient to make it profitable to mine and recover the copper in the form of marketable metal. Manifestly, under a literal interpretation, a mass of material might be copper ore one day and merely copper-bearing waste rock a week later, if the price of copper happened to drop in the interim. Emphasis already has been placed on the expansion that took place in the ore reserves of the Porphyry companies as a consequence of the great strides made in the technique of mining and ore treatment. So, even if one inserted a qualifying phrase, "at an average price for the metal," after the word "profitable," the definition would still be open to criticism. Place is another factor. It is evident that a body of excellent ore in Arizona might cease to be ore in the economic sense if it were moved intact to the interior of China. However, it is with ore in its technical and scientific aspect that this chapter is concerned. Speaking in general terms, the ton of Porphyry ore as it arrives at the surface contains 25 to 70 lb. of copper minerals in the form of disseminated particles or thin coats along fracture planes. When subjected to appropriate treatment this ton yields 12 to 40 lb. of metallic copper. These ranges take into account conditions of today and of 25 years ago. Two procedures are available: (1) concentration, followed by smelting of the concentrate, or (2) leaching and precipitation, usually by electrolytic deposition. Smelting and leaching are metallurgic processes in that they involve chemical change; concentration

Jan 1, 1933