Search Documents

By M. Cohen, D. J. Blickwede

Quantitative observations concerning the carbide phases in high speed steel are of importance for two general reasons: (1) the carbides, being inevitable constituents of the final structure, exert a direct influence on the properties of the steel; and (2) a substantial proportion of the total alloy content is tied-up in the carbides, and hence the extent of their solution on austenitizing governs the composition of the steel matrix. The latter relationship has a vital bearing on the response of the steel to tempering as well as on its performance in subsequent service. Accordingly, in the course of a long-term study of the behavior of high speed steels, the authors were confronted with the problem of securing quantitative data on the carbide phases. The obvious method for acquiring such information is to isolate the car-bides from the steel and subject them to chemical, X ray diffraction and other measurements. There are well-known extraction techniques which involve the chemical or electrolytic solution of the less noble matrix (ferrite, marten-site or austenite), thus leaving a residue of the carbide phases. However, the results obtained must be scrutinized carefully1,2 since the carbides may be affected by the chemical or electrolytic action. It is the purpose of the present paper to describe the experiments leading to an electrolytic-extraction technique for quantitatively isolating the carbides from both I and hardened high speed steel. Particular attention is paid to the amount, as well as the composition, of the carbides so that the matrix analysis becomes ascertainable by subtraction from the overall steel composition. Illustrative results are given for the M-2 grade of tungsten-molybdenum steel. Review of the Literature The chemical method of dissolving the matrix selectively with respect to the carbides makes use of dilute non- oxidizing reagents such as hydrochloric or sulphuric acid. Although this simple procedure has led to the determination of the cementite composition,3,4 it achieved only limited success because of the interaction between the acid and the carbide residue. Some of the carbides may not only be destroyed in this way, but the hydrogen released is likely to remove part of their carbon as hydrocarbon gases. The electrolytic technique of isolating carbides has the advantage of rapidly dissolving the specimen (anode) in the presence of less reactive solutions than are practicable with the chemical method. This reduces the possibility of chemical attack on the carbides, and furthermore, the hydrogen evolved during the electrolysis is released at the cathode which is not in close proximity to the carbides. The common electrolytes adopted for this purpose are hydrochloric and sulphuric acids.5-l1 Aqueous solutions of ferrous salts have also been used.12,13 A considerable advance in experimental technique was introduced by Treje and Benedicks14 who developed a double-compartment cell for electrolytic extraction, the anode and cathode chambers being separated by a porous diaphragm. A solution of 15 pct sodium citrate, 2 pct potassium bromide and 1 pct potassium iodide was selected for the anolyte, while the catholyte consisted of a 10 pct solution of copper sulphate, with copper serving as the cathode. This type of cell has a number of desirable characteristics: 1. The anolyte has a pH value close to 7, at least at the beginning of the run. 2. The iron that dissolves from the anode-specimen forms a water-soluble complex ion with the citrate, thereby preventing the precipitation of iron hydroxide (which would contaminate the carbide residue) despite the neutrality of the solution. 3. Copper deposition instead of hydrogen evolution occurs at the cathode, and this avoids an increasing concentration of hy-droxyl ions which (in an otherwise neutral solution) might cause the precipitation of insoluble hydroxides. 4. Contamination of the anode chamber by copper sulphate is inhibited by the porous diaphragm. Houdremont and coworkers15 applied the above method (with the further refinement of excluding oxygen during the electrolysis, washing and drying) to the extraction of carbides from a series of plain carbon steels after various heat treatments. They had quantitative success only with specimens in the annealed condition, and concluded that the size and shape of the carbide particles play an important role in the isolation process, with large spheroids exhibiting the least tendency to decompose during the electrolysis. Up to the present time, the citrate double-cell has not been used to any extent for isolating the carbides of high alloy steels, apparently on the grounds that the complex carbides are more resistant than cementite to attack in the simpler acid electrolytes. In particular, Bain and Grossmann7 and Gulyaev10.10a have employed the hydrochloric acid cell for their investigations of the carbides in high speed steel.* It will be demonstrated here that this type of cell is capable of yielding quantitative results in the case of high speed steel, and actually has certain advantages over the more complicated double cell. However, in order to provide a rigorous test of the quanti-tativeness of electrolytic procedures for the problem at hand, both methods were studied in considerable detail.

Jan 1, 1950

MARCH 15-Industry is rapidly snapping back from another coal crisis, other business news is in general favorable and the outlook through the Spring is by most observers considered quite promising. Most industries report comfortable backlogs of unfilled orders, department store sales in recent weeks have equalled in dollars those of the corresponding period last year, retail sales of automobiles show again over the same period a year ago, and new orders for machine tools are at the highest figures since August 1946. Orders for railway freight cars have shown a very encouraging pickup, with a total of 9385 cars in January and the N. Y. Central alone ordering 4500 in February. Construction continues very active. In January new housing starts totaled 80,000 against 50,000 a year ago and the daily average contract awards, according to the Dodge reports, were 57 pct larger. In the first 22 days of February the increase in awards was 27 pct. Lumber orders since Jan. 1 have run 22 pct above last year. All of these favorable factors bolster the opinion that the upturn in industrial output and employment which began last summer has not yet spent itself and that the setback caused by the strikes will be made up when people get back to work. Only in a few lines are there indications that primary production may be outrunning the consumption of finished goods, although inventory build-up would seem to be rather modest as the National Association of Purchasing Agents reported in February that 78 pct of its members were buying for 60 days or less. Industrial prices as a whole show no significant trend despite the continued alarm over both the immediate and the long-term possibility of inflation caused primarily by the government's increasing expenditure and its inability to balance the budget. A recent advance of 1.9 pct in primary market prices is viewed by some people as the surface symptom of renewed inflation, but even so it is more than two years since the alltime high was reached by the daily index of sensitive commodities in November 1947. Over two years have passed since prices received by farmers hit their peak and about a year and a half since all wholesale prices and the consumer price index touched their highest points in August 1948. The decline in the wholesale price index has been almost continuous, interrupted only twice by slight advances in the monthly figures from February to March 1949, and, later in the year, from August to September. Of course, this continued decline in the last half of 1949 largely reflects a downward movement in farm and food prices. Wholesale prices for commodities other than farm and food leveled out after June and now stand only slightly under the June level. Farm products are down by 22 pct from January and by 18.6 pct from August 1948. Food prices are down only slightly less. Consequently, the farm price support program is in serious trouble and has imposed a heavy financial burden on the Treasury. In those commodities other than farm products only building materials, chemicals and textiles have come down as much as the average, while housefurnishings and metals and their products have fallen hardly at all. Glancing away from the domestic front, the results of the British general election indicated a highly inconvenient situation, that public opinion there is so exactly deadlocked as to divest the victors of much ability to make forceful decisions or create significant policy. It is generally considered that another election in the near future would give substantially the same result. The British people are equally divided and the politicians are not likely to precipitate another appeal to the country until there is manifest reason to believe that external and internal circumstances have changed sufficiently to permit one party or the other to obtain a decisive verdict. Because of the lack of a clear mandate steel nationalization will likely lag in Britain. In the meantime there is considerable discussion going on as to whether the European steel industries as a whole are at a disadvantage in world competition with the American industry. An article in the "Statistical Bulletin" for January of the British Iron and Steel Federation takes issue on this point with the authors of the Geneva report, observing that they wrote before devaluation, and this particular conclusion "has been overtaken by events." The "Bulletin" also contends that the statement was in any case incorrect so far as Britain was concerned, and that it was based on scanty and insufficient evidence. To support the rebuttal a detailed and extensive comparison is made of the home prices of certain steel products in Britain and in other countries of the world. The accompanying table gives a selection of the prices published. It sets out the changed position since devaluation and since the recent increases in American steel prices. These are home market prices; no doubt in competitive export business some of the price levels could be brought closer together at need.

Jan 4, 1950

Mark R. Lamb, Torres, Sonora, Mexico (communication to the Secretary*): I have read Mr. Merrill's paper with much interest, and cannot but accept his challenge as regards the cost of the clean-up at the Homestake mill. If I understand him correctly, the two men take the precipitates from the presses in about six hours, and do nothing towards refining them. If that is so, it would correspond to the work four men do here in about eight hours—that is, to clean the box and to place the precipitates in the driers. In order to make a fair comparison, the bullion in each case should be stated in ounces, since it is as diflicult to precipitate silver as gold, and our bullion is mostly silver. Bullion to the value of $50,000 is equivalent to a weight of about 2,500 oz. At our last clean-up eight standard bars, each 1,100 oz. in weight, were made, which equals a total weight of 8,800 oz'. Four men had the precipitates drying by 8 p.m. This plant, the Minas Prietas works of Charles Butters & Co., at Minas Prietas, has square-bottomed electrolytic vats, an arrangement which necessitates the handling of all the precipitates in buckets. The Butters plant at Virginia City, Nev., is equipped with conical vats, and probably could make a still better showing under similar conditions. Another point is that common labor only is required. (Ordinary laborer's wages at Minas Prietas are $0.70 gold.) I may say also that, except for the convenience of the refinery, the box could be cleaned monthly, instead of bi-monthly, at only a slight additional expense. The comparison, if made a few months ago, would have been much more in favor of the electrolytic process, as the tailings handled at that time contained a large quantity of copper, and the amount of zinc-dust required would have been enormous.

Jan 1, 1904

By A. S. Grove, C. T. Sah, E. H. Snow, B. E. Deal

A summary of- several recent investigations in to the properties of the metal-oxide-silicon system is presented. A major portion of these studies makes use of the MOS capacitance-z)oltage method of' analysis. The particular areas of investigation which are reported include: 1) a general survey of the electvical properties of thermally oxidized silicon surjbccs; 2) a study of ion migration through silicon dioxide films ; 3) measurements of electron and hole mobilities in surface inversion layers; 4) a study of impurity redistribution due to thermal o.ridatiotz; and 5) measurements of the rates of oxidation oj-heavily doper7. silicon. THE importance of the metal-oxide-semiconductor (MOS) system in the semiconductor industry is well-known. In addition to its importance in the "planar" device technology,' the MOS structure is now also used in the fabrication of active solid-state devices. Consequently, extensive efforts have been made recently to obtain a better understanding of the characteristics of this system. A summary of some studies of the MOS system conducted in our laboratories during the past year is presented. For the most part these studies used silicon as the semiconductor, along with silicon dioxide and aluminum as the other two components of the system. Since the MOS capacitance-voltage method of analysis was used extensively in these studies, we will first briefly describe its nature and consider some of the possible causes of deviation of experimental observations from the simple theory. We will then outline the various related areas of investigation carried out in our laboratories and will briefly indicate some of the results. It should be noted that the purpose of this paper is merely to provide a brief summary of MOS studies. More detailed discussions of the various areas of investigation are given in the references cited. PRINCIPLES OF THE MOS C-V METHOD OF ANALYSIS' A sketch of the MOS structure is shown in the upper portion of Fig. 1. In this case the insulating film is Si02 and the semiconductor p-type silicon. If a large negative bias is applied to the metal field plate, holes are attracted to the silicon surface. The silicon then behaves much like a metal and the capacitance measured is that of the oxide layer alone, Co. If a small positive bias is applied to the aluminum, holes are repelled and a region depleted of majority carriers is formed at the silicon surface. This depletion I-egion adds to the width of the dielectric and the measured capacitance begins to drop. With increasing positive bias, the width of the electrical depletion region increases. At some large positive bias an inzevsion regiotr is formed at the surface and additional charges induced in the silicon appear in the form of electrons in this narrow inversion region. Thus the depletion-region width approaches a maximum value and, consequently, the capacitance reaches a minimum value and then either levels off or rises again depending on the measurement frequency and the rate of equilibration of the minority carriers in the inversion layer.3 Band diagrams, along with the corresponding charge distributions, are shown in Fig. 1 for the above bias conditions. If minority carriers cannot accumulate at the surface to form an inversion region, the depletion-region width continues to increase with increased positive bias and the capacitance drops toward zero as in a reverse biased p-n junction. The effect of a work-function difference $hs between the metal and the silicon, and of surface charges per unit area Qss located at the oxide-silicon interface, is simply to attract charges in the silicon much like the applied bias. It can be shown that this results in a parallel shift of the capacitance-voltage characteristic along the voltage axis by an amount corresponding to AV = -$bIs + Qss/Co. Theoretical curves have been calculated4 giving the capacitance of the MOS structure C normalized to the oxide capacitance Co vs the quantity VG here VG is the voltage applied to the metal field plate. In Fig. 2 such calculations are shown as points for a particular oxide thickness and bulk impurity concentration for a p-type semiconductor. (For an n-type semiconductor the curves would be mirror images of these.) All three cases, i.e., low frequency. high frequency, and depletion, are indicated. Also shown in the figure are recorder tracings of the characteristics of actual devices. These characteristics have been shifted along the voltage axis to compensate the effect of surface charges and work-function difference. It is evident that agreement between experiment and theory is good. The nature of this shift along the voltage axis is

Jan 1, 1965

By G. W. Healy, N. R. Griffing

The activity coefficient of sulfur in Cr-Fe-S melts was determined by measuring the values of Ph3Rh,in equilibrium with such melts. The results showed that chromium has a pronounced negative effect on the activity coefficient of sulfur, which up to about 20 pct Cr may be represented by the equation: log f; = - 0.019 pct Cr It was also found that the influence of chromium was not altered by the presence of appreciable amounts of carbon or silicon. The influence of alloying elements on the activity of sulfur in molten iron has been the subject of many investigations; however the effect of one important alloying element, chromium, has not been reported, and the object of the present investigation was to determine its effect on the activity coefficient of sulfur in liquid Fe-Cr-S alloys both in the absence and in the presence of carbon and/or silicon. EXPERIMENTAL PROCEDURE The general method employed consisted of passing mixtures of hydrogen and hydrogen sulfide over the sulfur-containing melt of interest and analyzing the outgoing gas to determine the equilibrium value of which resulted from the reaction shown in Eq. 111. H, (gas) + S (dissolved in melt) = H,S (gas) 111 The activity coefficient of sulfur, fs, was then calculated with Eq. [2] in which K, is the known equilibrium constant of Eq. [I] for dilute solutions of sulfur in iron. Raw materials used in the preparation of the charges included commercial grades of electrolytic iron and chromium and carbon-reduced, acid-treated silicon of 99.9 pct purity. Oxygen in the former presented no problem since it was removed by hydrogen in the normal course of an experiment. Carbon was added in the form of premelted iron-carbon and chromium-carbon master alloys. Sulfur was charged as iron sulfide prepared by first heating powdered iron and sulfur in air in an alumina dish until reaction occurred, and then deoxidizing by melting in a hydrogen atmosphere. Commercially bottled hydrogen and hydrogen sulfide were used after being passed through purification systems containing palladium, "Drierite," and magnesium perchlorate in the case of hydrogen, and "Drierite" alone in the case of hydrogen sulfide. Lamp-grade cylinder argon served as a flushing agent without further purification. Charges weighing from 300 to 500 g were placed in a high-purity alumina crucible of 0250-ml capacity and heated in an argon atmosphere in the induction-heated carbon-tube furnace illustrated in Fig. 1. During heating, a dry hydrogen atmosphere was substituted for argon in order that deoxidation of the charge and flushing out of argon would be accomplished sooner. After the charge melted, a Pt-Pt 10 pct Rh thermocouple contained in an alumina protection tube was immersed in the melt, and the desired melt temperature (usually 1600°C) was established. Higher temperatures up to 1760°C were required for some chromium-rich alloys because of their higher melting points, and in these cases a Pt 6 pct Rh-Pt 30 pct Rh thermocouple was used. The thermocouple output was fed to an automatic controller which provided straight line temperature

Jan 1, 1961

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the Ger- man techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low- cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first German assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission- to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high- cost coke and anthracite for the production of water gas. Although varying degrees of success have been achieved and the water gas produced generally has been higher in calorific value, in only a few isolated in- stances has there been any sustained use of bituminous coal for water-gas production for public utility uses after the shortages of anthracite and coke have been lessened.

Jan 1, 1946

By K. G. Wikle, W. W. Beaver

A general survey of the mechanical properties of commercially pure beryllium fabricated from powder by vacuum hot pressing and other consolidation methods is presented. The effect of fabrication method, grain size, strain rate, and directionality upon both room and elevated temperature tensile properties is reported. BERYLLIUM metal, in spite of its rather restricted use, has been the object of attention for many researchers in the past half century. However, such work was performed on special experimental lots of metal made in small quantities by a variety of reduction methods. Not until 1946 was there a substantial production of beryllium metal, and not until 1950 was there a steady production of a commercially standard beryllium in the United States. This output was both the result of a requirement of the Atomic Energy Commission for a high grade beryllium of consistent quality and the development of a powder metallurgy process, by the Brush Beryllium Co., known originally as Process Q, which yielded a fine grained beryllium suitable for fabrication. Because this powder metallurgy product, known as QMV, superceded other types of metal made previously and represents the great majority of beryllium in use today, it seems worthwhile to present the results of studies on the mechanical properties of this metal as currently made. To the design engineer and the metallurgist, beryllium has extremely interesting properties. It is as light as magnesium alloys while having a stiffness modulus 40 pct greater than steel and a strength-weight ratio superior to titanium and aluminum alloys and aircraft steels. The melting point is high, 1287°C (2348°F), and it has good corrosion resistance both in air and water. Also, it is highly transparent to X-rays and has good heat and electrical conductivity (electric conductivity is greater than 40 pct of Cu). To the atomic energy program beryllium is considered a valuable material because of its low neutron-capture cross section and high neutron-scattering cross section which make it a good moderator and reflector for the lower velocity neutrons. A major technical difficulty limiting the use of beryllium, especially in structural applications, has been its notch sensitivity and consequent room temperature brittleness. Kaufmann, Gordon, and Lillie1 have reported their work on the mechanical properties of beryllium performed from 1946 to 1950. They studied the room and elevated temperature properties of cast and extruded beryllium and extruded electrolytic flake, Table I. Cast and extruded alloys of 85 to 99 pct Be were tested also. They found that extruded metal developed good strength and appreciable ductility in the extrusion direction and that thermal treatment and alloying provided little improvement in mechanical properties. They concluded that preferred orientation and fine grain size were the means of obtaining optimum tensile properties in beryllium. Other investigators have measured and commented on one of the most striking mechanical properties of beryllium, namely, its abnormally low Poisson's ratio.2 Udy, Shaw, and Boulger3 presented the latest published survey on properties of beryllium but their information is based only on published data available before April 1949 and cites little information on metal fabricated by powder metallurgy

Jan 1, 1955

By George G. Binder Jr., James W. Lacey, Arthur L. Draper

An experimental investigation of miscible fluid displacement has been made in linear porous media under highly adverse mobility ratio conditions. Various refined oils were displaced at field rates by liquid propane in both horizontal and vertical models 9 to 36 ft in length. In horizontal tests, mixed zones or transition zones form between the two liquids early in the displace-lents. Initially, the zones grow rapidly. III 2-in. diameter models, the mixed regions become nearly stable zones from 6- to 20-ft long. From then on these quasi-stable zones apparently grow only by molecular diffusion. The lenghts of the quasi-stable zones appear to be almost independent of the core material in which displacement;; are made and increase with increasing rates of injection and oil/solvent viscosity ratios. The lengths of the quasi-stable zones. measured in 2-in. diameter models at viscosity ratios and injection rates anticipated in the field indicate that essentially piston-like displacements of oil by solvent would occur. However, the mixed zone lengths increase markedly as the model diameter increases. In vertical displacements controlled by gravity drainage, only short trans-sition zones form. The entire lenghts of these zones can be accounted for by molecular diffusion. Therefore, in reservoirs having characteristics allowing a high degree of gravity drainage, nearly complete oil recovery should be attainable by miscible fluid displacement. INTRODUCTION The oil industry is faced with an ever increasing cost for finding new oil reservoirs. This, coupled with the fact that conventional methods of oil recovery usually leave from 1 to 3 bbl of oil in the ground for every barrel produced, has aroused considerable interest in developing more efficient methods. An integral part of the mechanism of many of these new methods of recovery is a miscible fluid displacement in which oil is displaced by a much less viscous materiai such as liquid propane. A numher of irlvestigators have explored the mechanics of miscible fluid displace-ment,'.2.1.'."." but in the experiments reported many of the important factors have been varied only over a limited range far removed from norma1 oilfield values. This paper presents the results of an experimental study of oil displacement by liquid propane at field rates from linear, natural-sandstone models of various sizes. Both horizontal and vertical flow tests were made. EXPERIMENTAL APPARATUS AND PROCEDURE Refined oils with viscosities varying over a wide range were displaced at several rates by liquid Propane from both horizontal and vertical flow systems. The behavior of the displacement was observed by propane-oil analyses of the effluent and, when possible, by differential pressure measurements along the cores. A schematic flow diagram of the apParatus used to conduct the experirents is shown in Fig. 1. The cores used in the tests were 9-ft lengths cut from natural consolidated sandstone and turned to the desired diameter. These were cast in steel tubing with a low melting point (160°F) alloy which expands on solidification. Flanges welded to the ends of the steel pipes permitted sealing the ends or butting one core to another. Pressure seals were maintained with O-rings. The cores were cleaned by flushing

By Charles R. Keyes

Continued discussion of the paper of Charles R. Keyes, Trans., xxxix., pp. 139 to 169, 850 to 856, and Bulletin Ho. 34, October, 1909, pp. 945 to 947. CHARLES R. KEYES, Des Moines, Iowa (communication to the Secretary*):-It is with pleasure that I acknowledge the value and interest of the historical notes on early mining at Lake Valley, contributed by Messrs. MacDonald and Courtis. In my own paper there was no attempt to enter into this phase of the subject; partly for reason that the intention was to take up this in detail in another connection, partly because there was not space enough to. devote to it in a brief geologic paper, and partly on account of the fact that the strictly mining features are quite distinct from the purely geologic characteristics. As may be inferred from its perusal, the brief historical paragraph prefacing my paper was in reality geologic in its bearing. The events referred to therein relate to the published information concerning the geologic structure. The personages principally mentioned were noted merely to show how the names of several of our most distinguished scientists came to be closely associated with that of Lake Valley. Far from my intentions was it to slight the memory of any , of that brave band who, with lives in their hands, took so active a part in the early development of the mines. The value of their records is perhaps much greater than that of any published notes. The narratives of Messrs. MacDonald and Courtis are as thrilling as many other experiences related of that time and place. Few of us at the present time can appreciate the dangers of that early day, when the fierce Apache all but swept the. white man from that part of the country, when renegades from Texas overran the land, and when the outlaws of the nations took their last stand before advancing civilization. In marked contrast do we to-day reach Lake Valley by means of the 11 iron horse"; and out of a luxurious Pullman

Apr 1, 1910

By Wm. B. Price

The work of Leon Guillet concerning the effect of nickel on the structural properties of brass is checked. The best value for the coefficient of equivalence t, that is, the amount of zinc replaced by 1 per cent. of nickel, is shown to be-1.1 per cent. The best hot- and cold-working nickel silvers, varying in nickel content between the limits of 4 and 18 per cent., are tabulated and plotted diagrammatically. Also, some data are given showing a comparison between the physical properties of a hot- and cold-working low copper-nickel silver, and a commercial cold-working nickel silver containing approximately 8 per cent. more copper. THIS investigation of low copper-nickel silvers was undertaken to check the work of Leon Guillet on special brasses and to determine, more accurately, the effect of the addition of nickel on the microstructure of the binary alloys of copper and zinc. It was hoped that the results could be successfully applied to the practical production of low copper-nickel silvers. To explain the results of his investigations on special brasses, Leon Guillet evolved his conception of "fictitious compositions." He states,1 in his general conclusions, that on the introduction of a small amount of a third metal to a copper-zinc alloy, it enters into solid solution with the normal constituents up to saturation, but by so doing it brings the ternary alloy into a state microscopically equivalent to a binary copper-zinc alloy of fictitious composition, and physically more nearly like the latter than the brass containing copper-zinc in the ratio actually present. The physical properties of the ternary alloy, when compared to the same properties of an actual brass of the fictitious composition, are modified by the natural properties of the third element. Beyond the point of saturation, a special constituent appears and the above generalization no longer holds.

Jan 2, 1924

By L. L. Wyman

IN order to clarify and amplify the existing data concerning the action of the cementing material in cemented tungsten carbide alloys, the authors have initiated this investigation of the entire range of cobalt-tungsten carbide alloys. Inasmuch as the ultimate objective is relative to what actually goes on during the sintering of cemented tungsten carbide materials, this work was necessarily restricted to heat treatments similar to those used in actual production of these materials. In the course of numerous experiments, the authors have noted several conditions that indicated that there was a solubility to be considered. Among these factors are the following: 1. Many of the alloys showed a much larger amount of binding constituent to be present than could possibly be accounted for by the cobalt content. 2. In many areas, grains of the carbide constituent are much larger than the particles of carbide originally added. In addition, these grains are of very regular contour. 2a. In samples of cemented tungsten carbide which had been fused in the atomic hydrogen torch in the presence of excess hinder constituent, immense grains are formed, and their shapes are very regular. This is also true when the cemented tungsten carbide of 13 per cent. Co content is fused alone in the atomic hydrogen torch. Contrary to general expectation, chemical analysis of this material, after fusion in the atomic hydrogen torch, checks the analysis of unfused material. 3. In making the cemented tungsten carbide materials by the process of exerting the pressure at the time of heating a certain portion of the contents squeezed out of the mold. Chemical analysis has shown that this material contains approximately 12 to 20 per cent. of tungsten. The microstructure shows a cored dendritic structure interlaced with eutectic network, and some graphite, as shown in Fig. 1. 4. Thermal analysis of these materials has consistently indicated an arrest point close to 1350° C.

Jan 1, 1930

By Cyril Stanley Smith

Somewhat over ten years ago the author described studies1'2 on the constitution of the copper-silicon system. The copper-rich portion of this diagram is shown in Fig. 1. The experimental points freely dotted about the diagram seemed to justify an otherwise unconvincing diagram and for several years the curious reverse bend in the alpha-phase boundary was accepted as substantially correct, even by later investigators3 of the system who introduced changes in the high-silicon phases. The binary diagram has been used as a base for several ternary systems5-9 without any suggested changes. Voce10 suspected the existence of another phase from his study of the cast alloys in the copper-manganese-silicon system, but evidently hesitated to extrapolate this to the binary diagram, particularly in view of the too ingenious explanation that was advanced1' to account for the pools of constituent clearly visible in castings; namely, that they were secondary alpha of twinned orientation deposited from beta. Von Schwarz,12 in 1932, called attention to the fact that this micro-constituent in copper-silicon alloy castings was anisotropic under polarized light and asserted that a new phase, not cubic, should be placed in the diagram .adjacent to alpha. Sautner,l3 on the basis of investigations with the polarizing microscope and with X-rays, introduced this phase into the diagram at about 6 per cent Si. The relevant part of his diagram is shown in Fig. 2. Sautner called the new phase beta, renaming the old beta phase zeta. To avoid confusion, in redrawing Fig. 2 the phases have been renamed in accordance with the terminology adopted in the present paper, in which the new phase is called kappa and the other phases retain the designation given them by Arrhenius and Westgren.4 The thermodynamic impossibility of Sautner's diagram and the paucity of experimental data left the exact location of the new phase field most uncertain, although his work proved beyond doubt that an additional noncubic phase exists. Because of the industrial importance

Jan 1, 1940

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Cyril Stanley Smith

Somewhat over ten years ago the author described studies1'2 on the constitution of the copper-silicon system. The copper-rich portion of this diagram is shown in Fig. 1. The experimental points freely dotted about the diagram seemed to justify an otherwise unconvincing diagram and for several years the curious reverse bend in the alpha-phase boundary was accepted as substantially correct, even by later investigators3 of the system who introduced changes in the high-silicon phases. The binary diagram has been used as a base for several ternary systems5-9 without any suggested changes. Voce10 suspected the existence of another phase from his study of the cast alloys in the copper-manganese-silicon system, but evidently hesitated to extrapolate this to the binary diagram, particularly in view of the too ingenious explanation that was advanced1' to account for the pools of constituent clearly visible in castings; namely, that they were secondary alpha of twinned orientation deposited from beta. Von Schwarz,12 in 1932, called attention to the fact that this micro-constituent in copper-silicon alloy castings was anisotropic under polarized light and asserted that a new phase, not cubic, should be placed in the diagram .adjacent to alpha. Sautner,l3 on the basis of investigations with the polarizing microscope and with X-rays, introduced this phase into the diagram at about 6 per cent Si. The relevant part of his diagram is shown in Fig. 2. Sautner called the new phase beta, renaming the old beta phase zeta. To avoid confusion, in redrawing Fig. 2 the phases have been renamed in accordance with the terminology adopted in the present paper, in which the new phase is called kappa and the other phases retain the designation given them by Arrhenius and Westgren.4 The thermodynamic impossibility of Sautner's diagram and the paucity of experimental data left the exact location of the new phase field most uncertain, although his work proved beyond doubt that an additional noncubic phase exists. Because of the industrial importance

Jan 1, 1940

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By G. E. Steudel

THE study of the possibility of effecting a lower cost in the manu-facture of pig iron reveals the importance of the ever present question of slag chemistry and volume. Factors that determine slag chemistry and volume are the impurities in the ore available, the ash-sulphur content of the coke, and a flux material necessary to promote removal of sulphur. Of these, the ores present by far the major source of impurities and what may prove to be the lowest practical slag volume with desired chemistry in one locality may be considered low or high in some other center of iron manufacture. The Chicago district is not only blessed with ores of high quality, but with excellent coke and flux materials as well. It is the intent of this paper to discuss slag problems at the South Works only, where burdens consist of Mesabi ores, Michigan stone, and coke ranging from 7 to 9 per cent ash and containing an average of 0.57 per cent sulphur. Early in the development of modern blast-furnace practice, the con-sideration of slags was secondary to the many adjustments of mechanical difficulties, such as furnace lines, stock distribution, stove design for obtaining higher blast temperatures, improved chemical segregation and size of raw materials. Furnace operators, after making these improve-ments, turned their attention to the study of other refinements in practice, of which slag chemistry appeared to be the most important. It is only within the last two decades that operators have become familiar with the various aspects of slag compositions. The industry, while rather slow in its recognition, is indebted to such investigators as Rankin,1 Wright,1 Feild,2 Royster,2 McCaffery,3 Kinney,4 Holbrook,5 and Joseph5, whose researches concerning the elimination of sulphur within the blast furnace and the effect of slag composition upon melting point, viscosity, and desulphurizing power have established criteria for the selection of slags of the requisite quality.

Jan 1, 1939

By Hans Lundberg

BASED upon an instrumental improvement, a new development has taken place in the art of electrical prospecting, and some remarkable results have already been obtained with regard to potential exploration. In order to visualize the importance of this development, it is deemed advisable to review briefly the fundamental facts about potential surveys. Potential exploration may be carried out qualitatively or quantitatively. Qualitative investigations are made by determining and plotting on a map points of equal potential, whereby any anomalies are revealed, without, however, much clue to their magnitude. Quantitative investigations determine the variations of potential or potential drop, and thus show not only the location of the anomalies, but also their magnitude. Figs. 1 to 6 illustrate the influence of simple types of ground inhomo-geneities, assuming one effective exciter potential only. Such a condition can be closely realized by connecting an electric current source to two electrodes, one of which, is located at a great distance. Assuming uniform ground resistivity, the resultant potential distribution may be represented by concentric spheres. Any change from the normal condition causes a characteristic distortion of the spheres, which becomes different for different types of resistivity variation. The series of Figs. la to 6a illustrates schematically results of qualitative investigations and series 1b to 6b results of quantitative investigations. Figs. 1 and 2 picture the well-known case of local resistivity variations normally encountered in ore prospecting. Figs. 3 and 4 show the reactions caused by more or less vertical resistivity contacts and Figs. 5 and. 6 refer to the problem of ground-water and bedrock investigations where the resistivity contact is horizontal or nearly so. It is evident from Figs. 5a and 6a that qualitative measurements do not permit an identification of such general geological features as widespread horizontal strata, because the resultant contraction or expansion of the equipotential circles at the surface cannot be recognized without quantitative determinations. On the other hand, qualitative measurements are well suited for the exploration of local or lateral resistivity

Jan 1, 1931

By G. L. F. Powell

Bulk samples of silver have beat undercooled lo a large degree in contact with crystalline siliceous and ceramic oxide materials, indicating lhat stable oxides and oxide compounds are not the heterogeneous nucleants which normally catalyze cryslallization within a feu degrees of the equilibrium freezing point. Since 400-g samples were undercooled 250°C in contact with cristobalite, it is concluded that the undercooling required for homogeneous nucleation of sil11er is greater than 250°C. Undercooling was Jacilitated by precleaning the crucibles with a high-fires -sure blast of gas. IN numerous experiments on the undercooling of metal melts it has been assumed that a solid glassy surface, being non crystal line, will have no effect in catalyzing crystal nucleation from the melt. Conversely, it is usually accepted that any crystalline surface, in contact with a metal melt, will catalyze nucleation of metal crystals from the melt at degrees of undercooling less than that at which homogeneous nucleation will occur. Both these assumptions were implicit in the claim that homogeneous nucleation was observed in experiments1'2 on the undercooling of small metal droplets (10 to 100 mp diam). The droplets were thought to be freed of suspended crystalline particles which would otherwise catalyze heterogeneous nucleation. They were supported on flakes of silica glass which were assumed to be amorphous, and therefore incapable of acting as substrates for heterogeneous nucleation. In later experiments, large samples of molten metal were undercooled to temperatures similar to those achieved by the droplet technique by melting in a fused-silica crucible3 or a boro-silicate glass slag.4 Since these samples were usually fully enclosed in glass at the moment of freezing, it seemed possible that nucleation was homogeneous when maximum degrees of undercooling were achieved, despite the large size of the samples (up to 500 g). In experiments on the undercooling of silver5 the metal was contained in vitreous silica crucibles, the

Jan 1, 1968