Search Documents

Jan 1, 1934

By C. H. Li, R. J. Stokes, S. H. Bendel, J. A. Sartell, T. L. Johnston

The mechanism of the oxidation of high-purity copper has been studied at temperatures from 500° to 981°C employing gravimetric, high-temperature microscopic and inert marker techniques. An investigation of the adhesion of copper oxides was also made. The oxidation of copper is found to be parabolic at all temperatures. It is concluded that the controlling mechanism is the outward diffusion of CU+ ions through the Cu2O layer, but the mechanism of diffusion is modified by the state of compressive stress in the oxide layer at the oxidation temperature. At temperatures below the transition from elastic to plastic behavior of Cu2O the growth stresses reach a value sufficiently high to cause CuO whiskers to be extruded. The extrusion of whiskers results in the injection of a large number of vacancies into the CuO. The Cu20 layer grows by the advance of the CuzO/CuO interface into vacancy-rich CuO. Since there is an adequate supply of non -thermally created vacancies, the activation energy for oxidation is that required to move the Cu+ ion through the appropriate saddle point to a neighboring vacancy, which has been determined to be 20,000 cal per mole. At temperatures at which the Cu20 can deform plastically the stresses are never high enough to cause whiskers to form. thus vacancies must be supplied by themal activation and as a result the activation energy increases to 40.000 cal per mole. ALTHOUGH extensive studies of the oxidation kinetics of pure copper have been made in the past. the mechanism has received relatively little attention. As a result, certain features of the kinetic data have not been satisfactorily explained' For example, several workers1,2 have reported that the activation energy for oxidation in the range from 500° to 700° C was about 20,000 cal per mole whereas that above

Jan 1, 1960

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment, these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In U.S. Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center's 900-lb per hr pilot plant, approximately 85% of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to 51000 ppm equivalent SiO*, while maintaining a Ca(II) content of =16 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water. Water quality is perhaps as important to flotation as are the reagents used. The character of water is extremely variable, depending on whether the source is a well, lake, or stream, upon the season and temperature, upon prior use, and upon the character of the watershed. All of these factors influence the water hardness and the quantity of other dissolved inorganic salts, turbidity, dissolved and suspended organic matter, dissolved gases, and pH. Frequently, the differences in water quality can measurably influence flotation selectivity, often to the point of spelling success or failure. Water hardness is particularly troublesome in flotation systems employing fatty acids, but other unrecognized constituents may also contribute to peculiarities in flotation behavior. Furthermore, a given water source may be entirely satisfactory in one flotation system, but entirely inappropriate in another. In recent years, society has given more attention than formerly to water use, even in areas where water is plentiful. However, both the demands of a growing population, with increased per capita needs, and also those of industry must be met. As a result, riparian rights must be negotiated with the appropriate government agency or agencies so that consumption of water is often allocated or otherwise controlled. Furthermore, the disposal of off-process industrial and domestic water is coming under the increasing scrutiny of these same governmental units. In these respects, the mineral industry is no exception, so that conservation, water reclamation, and reuse may be expected to assume increasing importance. In 1932, it was stated that, "water reclamation is generally more expensive than the economy in water and reagents resulting from its use. It is employed only if it is urgent to save water."' The economic aspects of this statement may still be true, but the unrestricted use of water is becoming less and less an option of the user. The purpose of this paper is to discuss an investigation conducted by the U.S. Bureau of Mines (USBM), in which water reclamation and treatment were undertaken to develop procedures for, and to assess the effects of, water reuse on the flotation treatment of nonmagnetic taconites. This investigation is a logical extension of previous work described by the author and associates at the Twin Cities Metallurgy Research Center employing selective flocculation-desliming and anionic flotation of silica from low-grade, nonmagnetic iron ores2,8 The requirements for the selective flocculation-de-sliming and the anionic flotation of silica processes determined the direction of the investigation. Previous studies had indicated that pH levels of about 11.0 and 11.8 were required for selective flocculation and flota-tlon, respectively. The calcium content of the water was believed to be of importance in both of these operations, and since Minneapolis tap water with a Ca(I1) content of about 16 ppm had been successfully used, an attempt was made to reclaim the process water at an equal level of dissolved calcium. Additionally, the objective was to nullify or effectively limit the effects of dispersants and fatty acid residuals from prior stages of processing. Last but not least, the system of water treatment had to have the capability of reducing turbidities to workable levels. With about half of the effluent being derived from the selective flocculation-desliming step and carrying about 25,000 ppm of highly dispersed, suspended fines, this last objective appeared formidable at the outset. Procedures for water reclamation were derived, in part, from well-known mineral dressing practices, from past observations and investigations, and from concepts contained in various pertinent publications on water treatment."c These procedures involved: 1) flocculation with lime and poly electrolyte-type flocculants, 2) lime-soda-ash softening, 3) chemical precipitation, and 4) mineral surface adsorption. Control was exercised at various stages of water reclamation by frequent measurements of Ca(11), pH, and turbidity.

Jan 1, 1971

By P. W. Davies, B. Wilshire

PREVIOUS investigations on the effect of stress changes on the high-temperature creep and fracture behavior of metals have been confined mainly to the testing of complex alloys.172 Most of these alloys are structurally unstable during creep because of such effects as recrystallization, overaging, and so forth, so that the results are of limited application. The only pure metals on which observations have been made appear to be lead3,4 and aluminum5 tested under conditions which allow rapid recovery to take place. The present work describes the effect of a single stress change on the creep and fracture properties of a metal in which recovery is very slow. A Ni 0.1 at. pct Pd alloy was used so that grain growth and recrystallization did not occur during creep testing. Specimens of this material were heat-treated to give a uniform grain size of 10 grains per mm. Creep tests were carried out at 500°C using Denison T.47 machines; details of the creep-testing procedure have been given elsewhere.' All specimens were tested at a constant initial stress of 5 tpsi which gives, in an uninterrupted test, a minimum creep rate of ~10-3 pct per rnin and a life of -7000 min. Specimens were loaded under these standard conditions and after 1500 min, when secondary creep was well-established, the stress was changed to either 8, 7, 6, 4, 2, or 0 tpsi for a period of 180 min. After this time the original load was reapplied and the tests continued to fracture. The results are shown in Fig. 1. No detectable creep occurred during the period of reduced load, even at 4 tpsi, and on reverting to 5 tpsi the creep rate returned to its original value immediately. Increasing the stress to 8, 7, or 6 tpsi resulted in an instantaneous extension followed by a period of transient creep leading to a new steady creep rate. On returning from these higher stresses, the resulting creep rate at 5 tpsi was very low compared with the original value. Furthermore, the higher the stress during the stress change, the lower was the final creep rate. It is significant that the rupture life is comparatively unaffected by any of these stress changes.

Jan 1, 1965

By H. S. Ten Eyck

Fertilizer normally is spoken of as having three main components: nitrogen, phosphorus and pot- ash. Certainly, however sulfur must also be considered a basic component of fertilizers, even though in many instances it does not end up as a part of the end product. In addition, with heavier cropping and the resultant drain of plant foods from the soil, we have now reached a point where the minor elements necessary for plant growth have become a major factor in the fertilizer industry.

Jan 7, 1967

By W. R. Hibbard Jr., R. W. Guard, N. G. Ainslie

Evidence is presented that copper-base solid solutions of different solutes having equal grain sizes, no preferred crystal-lographic orientation, equal electron-atom ratios, and, within experimental scatter, identical initial yield strengths, need not have identical stress-strain curves at strains larger than about 0.04. The stress-strain behavior is rationalized in terms of the proposed Suzuki chemical interaction between solute atoms and extended dislocations using what is thought to be a somewhat different means of representing stress-strain data. ALTHOUGH the effect: of alloying element upon the strength characteristics of sold solutions is a subject which has received considerable attention in the past, the exact relationships between the common deformation parameters and certain common variables are not really known in some cases. As a result some of the experiments reported in the literature in which these variables are inadequately controlled lose some of their persuasion regarding underlying principles. Nonetheless, facts are known which bear pointing up: When the true stress, a, and true plastic strain, E, of tensile deformatic~n are plotted on a double logarithmic coordinate system, one may observe a straight-line relationship at strains greater than 0.02. The form of the curve in the linear region is given by a = Ken! where a represents true stress, E, true strain, and K and tn, constants. If the relationship holds, K and m define the flow characteristics of the material being tested. m and K, however, may vary with other parameters. Hollomon found that in a-brass, m is influenced by grain size. French and HibbardZ found in alloys of copper that inverse relationships existed between m and 1) the solute concentration for a given solute, 2) the 0.01 yield strength, and 3) the constantK. Lacy and Gensamer3 observed (du/d~) (= U/Em) to increase with increasing values of K in systems of alloyed ferrites (although with considerable scatter of data which may be attributed to uncontrolled grain size). Brick, Martin, and Angier* deduced in copper-base alloys a straight-line relationship (with some scatter) between the change in the Dph number due to solid-solution strengthening and the change in the Dph number due to work hardening which suggested that copper-base alloys having equal yield strengths might have identical stress-strain curves in the plastic flow regions. French and HibbardZ concluded that the yield strength of copper-base solid solutions is the proper basis for comparing the effects of solute elements. Also, Allen, Schofield, and ate' showed that, within their experimental variation, copper-base alloys of zinc, gallium, germanium, and arsenic having the same electron-atom ratios have the same true-stress true-plastic strain curves. Dorn, Pietrokowsky, and ~ietz' also found that with aluminum-base alloys the stress-strain curves in the flow regions are approximately the same if "equivalent" concentrations of alloying elements are used. Solute valence and lattice parameter distortion were the parameters used to determine equivalency. The present report describes an investigation in which an attempt was made to obtain copper-base solid-solution alloys of four solute elements having within close tolerances equal grain sizes and yield strengths, and to see if the level of yield strength does indeed define the flow curve regardless of solute type. During analysis of the data certain unexpected features of the stress-strain curves became apparent which gave rise to some speculation and are discussed at length in the paragraphs that follow. EXPERIMENTAL PROCEDURES Alloy Preparation—Using the data of French and HibbardZ as a first approximation, four different binary copper-base alioys were designed so as to have the same yield strength. In addition, other alloys were prepared in which the solute aoncentrations varied slightly from those calculated above so as to span a range of yield strengths, see Table L The yield strengths of all alloys prepared except the copper-tin alloys were subsequently found to Lie fairly close to one another. The copper used in the alloys was produced by the American Smelting and Refining Co. and was of very high purity (99.999 pct). The alloy additions and their initial purities are as follows:

Jan 1, 1960

By Laurence Hicks

CONSIDERATION of the past work on the subject of the diffusion of chromium into iron suggested that additional information might be given by the use of X-ray spectroscopy in following the concentration changes through the diffusion zone. Grübe and Fleischbein1 packed rods of electrolytic iron in a mixture of alumina and chromium. These specimens were heated in an atmos-phere of purified hydrogen for varying lengths of time. After treatment the specimens were examined metallographically and showed the usual structure, consisting of a border of radially oriented columnar grains ending in a sharp boundary line. Reference is made to the fact that etching with certain reagents will attack only the material inside the border of columnar growth and also to the fact that polishing seems to develop a ridge at the position of the boundary between the etched and unetched areas. By chemical analysis of thin layers turned off on a precision lathe, the authors were able to obtain depth-concentration curves. These curves, reproduced in Fig. 1, show that 'in most cases a pronounced change of slope occurs, corresponding to the position of the boundary of the columnar grains. In a later paper Grübe extends his work to other systems which show the same characteristics.2 He concludes that the reason for the break in the curve is that a hindrance of diffusion occurs at the place where the regularly oriented grains of the diffusion zone meet the random grains of the interior portion, on the assumption that the diffusion velocity in one direction in a grain may be greater than in another direction, and that the grains in the diffusion zone orient themselves so as to give the maximum diffusion rate. Kelley3 points out that Grübe has failed to note that the boundary line does not consistently cross all grains and

Jan 1, 1933

By H. S. McKnight

One phase of Canada's rapid development in mining and metallurgy during the past few years has been the creation of Canadian Copper Refiners Ltd., and the establishment of its modern electrolytic copper refinery at Montreal East, Quebec. Canadian Copper Refiners Ltd. is made up of three well-known metal firms whose combined activities cover the entire industry from the mine to the market. They are Noranda Mines Ltd., Toronto, Nichols Copper Co., New York, and British Metal Corporation, Ltd., London. Noranda Mines is the principal owner and provides the greater part of the raw material received by the refinery for treatment. Nichols Copper Co. designed and built the plant and is operating it under contract. British Metal Corporation acts as sales agent and markets the refinery's products. Montreal East was chosen as the site of the new refinery only after a careful survey had been made of the entire eastern part of Canada. The location chosen offers many advantages, chief of which arc the relatively low costs of power, labor, fuel and bupplies, and the fact that it is situated on Montreal harbor, the nearest seaport to the points of origin of the ram materials. All incoming material is received by rail. A majority of the plant's product is exported through the port of Montreal to European markets, being handled to the docks in railroad cars. A large proportion of the product is delivered by means of an industrial railway to the adjacent rolling mill of the Canada Wire & Cable Co., Limited. The refinery was designed to treat primarily the copper produced by Noranda Mines, Ltd. and Hudson Bay Mining &. Smelting Co., Ltd., and its rated capacity is 75,000 short tons per year. A general layout of the plant is shown in Fig. 1. Its capacity can be readily doubled, as shown by the dotted lines. Figs. 2 and 3 are sections taken through the furnace department and the tank house respectively. Except for the main office and laboratory and an auxiliary building containing the stores, warehouse, change rooms, compressor room and machine shop, the entire plant is under one roof. The type of building construction consists of reinforced concrete foundations supported on concrete piles, a steel structure covered with Robertson Protected Metal siding and a 3-in.

Jan 1, 1934

By Arthur S. Dwight

THE professional career of Thomas Septimus Austin, who died at El Paso, Tex., August 23, 1906, was contemporaneous with the growth of the silver-lead smelting-industry of the Far West, to which his talents and zeal contributed in no small degree. Born at Stratford, Conn., December 7, 1853, he was the seventh son in a family of thirteen. His parents were well-to-do; and he received a thorough preliminary training at the Hopkins Grammar School, New Haven, Conn., passing thence to the Columbia School of Mines, in New York, where he was graduated in 1876. His first professional work was that of analytical chemist with a Cuban sugar company. In this position he spent a year, and, whatever else of benefit he may have acquired during that year in Cuba, he gained a facility of speech in the Spanish language which was of inestimable value in his subsequent work in Mexico and the southwestern United States. In 1877, he went to the Rocky Mountains, and, under the firm name of Murphy & Austin, opened an assay-office in Leadville, Colo., which was just then coming into public notice as a rich silver-lead camp. The next year, however, he entered the service of the Germania Smelting & Refining Co. at Salt Lake City, Utah, where he remained until 1882, first as assayer and chemist, and later as Assistant Superintendent. The Germanic bears the honorable distinction of being one of the first of the large " custom " lead-smelters erected in the West. Its founders may be called the pioneers of the modern lead-smelting practice, and the Germania served, to a large extent, as a model for the many plants that sprang into existence during the next few years in Utah, southern Idaho, Colorado and other lead-producing districts. The formulation, for the first

Jan 1, 1908

JOHN W. BELL, *Montreal, Quebec, Canada (communication to the Secretary?). The test results in Mr. Taggart's paper will, I am sure, be recognized as a notable contribution, and of great assistance in the study of the performance of the Hardinge mill. I regret, however, being obliged to note that Mr. Taggart still retains. such confidence in the Kick-Stadler method of computing the ?relative mechanical efficiency" of crushing machines. The Rittinger-Kick graph submitted by Mr. Gates and the tests made at McGill University disclosed precisely the same fundamental defect in the Kick-Stadler theory. Consequently, I have been obliged to recalculate in terms of Rittinger surface units the results obtained in the 28 rock-crushing tests cited by Mr. Taggart, in order to find- out what the relative efficiencies really were. In order to show the large discrepancies between the Stadler and Rittinger R. M. R's, the most, efficient result disclosed by each method is represented by the number 100, and the R.. M. E.'s for the other tests have been recalculated on this basis. The results will be found in Table 1. Personally, I look forward to the time when we shall cease to talk about "relative mechanical efficiency" and merely refer to the "efficiency" of a crusher. All that is required to accomplish this is to agree on a standard method for determining the "crushing constant" of a given rock and a standard method for calculating the efficiency. The figures in the fourth column of Table 1 have been derived by assuming a constant of 2,000 for the quartzite crushed in the Yale tests. The Stadler method sometimes indicates changes in efficiency produced by, changes in operating conditions, as I pointed out in a paper describing rock-crushing tests made at McGill University. It is, however, not enough to determine that certain changes increase or decrease efficiency; surely it is equally important to determine the magnitude of these variations. By examination of Mr. Taggart's results, I have been obliged to conclude that the size of feed and amount of reduction greatly influence the Stadler R. M. E. figures, that they are positively misleading. It should be mentioned that since the majority of the tests have been made at the least efficient feed rates, and since, moreover, it is one of the evidently very important factors affecting efficiency, it is possible that different results might be obtained by a high-tonnage feed series, and that

Jan 8, 1917

An Appreciation of Dr. Douglas by Dr. ALBERT R. LEDOUX The Bulletins of the American Institute of Mining Engineers and the program of the International Engineering Congress, held last September at San Francisco, called attention to an important feature in the pro¬ceedings of the Congress; viz., the public presentation to Dr. James Douglas of the John Fritz Medal, for notable achievements in mining, metallurgy, education. and industrial welfare. Dr. Douglas' health, unfortunately, did not permit of his taking the journey to California. While he had been willing that the bestowal of the medal should be a public ceremony, his natural modesty made him shrink somewhat from what he considered something of an ordeal, and he begged those who were to take part in it to use restraint in anything which they might have to say as to his work and attainments. It was, therefore, with some considerable satisfaction on his side that he learned that the medal would be given him without a public, ceremony in New York, or elsewhere. . On Dec. 5, 1915, the writer of this had the pleasure of handing him the medal, certificate, and official letters of transmittal, at his home at Spuyten Duyvil, where lie was surrounded by his children and grandchildren, with one or two of his most intimate friends. He begged the writer to return his thanks to the Committee of Award; and again to express the feeling that nothing in his career merited so great an honor. On this point all of the members of the Institute will share the writer's feeling that Dr. Douglas is too modest. James Douglas was born at Quebec, Canada, in November, 1837. His father Was a distinguished physician and surgeon, employing his skill in the field of philanthropy: He established the first retreat for the insane in the Dominion, to which lie. devoted himself up to the time of his departure from Canada, when it was taken over by the Government. The son spent 2 years in study at the University of Edinburgh, which lie entered in 1855. Returning to Canada, he graduated from Queens University, at Kingston, Ontario, with the degree of Bachelor of Arts, having also studied medicine, and later theology. After his graduation he traveled extensively with his father in Europe and in the Orient, visiting Egypt several time's. They returned with important archaelogical collections, which Dr. Douglas subsequently donated to the Metropolitan Museum of Art in this city. He then returned to Edinburgh, where he continued his course in medicine, surgery being perhaps his chief interest at that time. He was subsequently licensed to preach and his contemporaries bore testimony to his broad philanthropy and to the sympathy which dominated his every act. His taste was distinctly literary; he had carried off a prize at Edinburgh in English literature.

Jan 1, 1916

By R. R. Sayers

TWO serious hazards from coal dust confront the bituminous-coal miner- -a physical or safety hazard and a physiological or health hazard. The first threatens the miner with loss of life from coal-dint explosions, and the second with loss of health and earning capacity from inhaling large quantities of the dust. Studies by the Bureau of Mines have shown that coal dust, except some grades of anthracite dust, is capable of initiating an explosion when no explosive gas is present and that its property of extending or propagating an explosion has been responsible for nearly all the widespread explosions that have occurred in bituminous mines in the United States in the present century. For years many mining people believed that low-volatile coal dust was not explosive but not only is it explosive but if the source of ignition is intense, it is as explosive as the dust of many high-volatile coals because the war is creating increased pressure for greater coal production and because of the trend toward greater mechanization in mines, explosion and health hazards from coal dust are likely !n increase considerably.

Jan 1, 1943

By Harry Warren

THE Geology Department of the. University of British Columbia has undertaken the task of examining the ores from as many as possible of the gold mines of British Columbia. The object of this work is two-fold. First, it is known that detailed mineralographic studies are useful in attacking ore-dressing problems, and these studies are intended to be helpful to mill operators. Second, it is hoped that mineralogical and mineralographical studies will prove useful adjuncts to those of lithology and structure in throwing more light on problems related to the origin of the deposits. The paper shows that gold, for all practical purposes, is not present in an ore mineral in solid solution nor as a eutectic with any mineral; if the latter were true the gold particles would be distributed equally throughout that mineral. The gold occurs either as native gold or as a gold-silver telluride and is not distributed regularly through any mineral or minerals: The relationship between the gold or gold-bearing telluride and the associated minerals affords a means of classification that is not only simple but also appears to be directly related to the geological nature of the deposit, which may be summarized as follows: 1. Disseminated Gold Type. ;-Precious minerals in extremely small grains, which are distributed without regard to grain size, fractures or grain boundaries: (1) Hedley variety-gold in native form; (2) Surf Point variety-gold predominantly as telluride. 2. Veining Gold Type.-Precious minerals in grains of various sizes, which occur mainly along fractures and grain boundaries: (1) Cariboo gold quartz-gold in native form. (2) Waneta variety-gold as telluride.

Jan 1, 1937

By William P. Blake

It is scarcely necessary to point out the important functions of water in the mining operations of man, especially in the State of California, where sluicing and hydraulic mining have been practiced on such a grand scale as to arouse the opposition of the agricultural interests. But the role which water and ice have played in mining or excavating on their own account is not so apparent. The alluvions of existing rivers, and the higher gravel-beds left by ancient streams, are doubtless the result of running water; but how far these gravelly materials owe their origin primarily as rocky debris and fragments of veins to glacial erosion, it is difficult .to determine. Yet we see on every side in our higher mountains unmistakable evidences of the cutting, crushing and eroding effects of glacial ice. We note that mountain-summits have been reduced in height and shaped into rounded and dome-like summits. We know that the general contour of the hills of New England, of the Highlands of the Hudson, and of the mountains of northern New Jersey, is due to glacial carving. The same is true of the Laurentian hills of Canada and of the mountains of all northern regions. And we recognize in the vast deposits of so-called " drift," which are spread out over the surface of the northern States, the chips and debris from the glacial workshops. Thus we cannot avoid the conclusion that there was an enormous amount of cutting and excavating in glacial times, and that vast quantities of veinmaterial and of ores and metals must have been liberated by ice-action.

Jan 1, 1900

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and re- quires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged be- cause a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced.

Jan 2, 1958

By Erwin H. E. Gaertner

The brown-coal opencast mines in Germany's Rhineland have to cope with several problems. Predominant are densely populated areas with highly productive farmland, many railroads, highways, and rivers, as well as towns and farm settlements which have to be removed before or during the lifetime of a mine. Also the ground- water table has to be lowered to keep the deep opencast mines dry and stable. These problems urged a development towards deep opencast mines with powerful machines; the large material movement and the high coal production are the basis for the economic success in working the Rhenish brown-coal deposits. Up to now, bucket wheel excavators with a daily capacity of 100,000 m3 (130,000 cu yd) are in operation. Machines of twice this capacity are under construction. Corresponding to the excavators development, the stackers' capacity has to be increased too. The new stackers will reach a daily capacity of 240,000 m3 (310,000 cu yd). The haulage in the mine is performed by conveyor belt systems, which are arranged in such a manner that the belt lines meet at a belt switching point. Here the incoming lines may be connected to the outgoing ones so as to direct the material flow to the desired receiving stations. At the moment there are conveyor belts in operation with a width of 2.2 m (7.2 ft); the new belts will have a layout for 37,000 t/h (40,770 stph), the width of which amounts to 3.0 m (9.8 ft). All belts and driving stations on benches are shiftable.

Jan 1, 1976

By W. O. Philbrook, K. M. Goldman, G. Derge

EQUILIBRIUM conditions for steelmaking reactions have been studied extensively over the past two decades by a .number of investigators, with gratifying results. Equilibrium data are essential to the understanding of any process, and such knowledge has the practical utility of placing a limit beyond which control measures cannot succeed. When, however, the driving rate of an industrial process is so fast that there is not time for reactions to reach equilibrium, it then becomes necessary that the factors which control the rates of reaction be known in order to establish full control of the process. The desulphurization of molten pig iron by slags within the iron blast furnace is one such process in which the actual degree of sulphur absorption by the slag does not approach the equilibrium distribution obtained for similar slag-metal systems in the laboratory.' A study of the rate-controlling factors governing the desulphurization of iron by slags is becoming increasingly important as the sulphur content of raw materials increases with depletion of higher grade ores and coal. Following up an initial study on kinetics,' this paper reports some results of a continuing laboratory investigation on the mechanism of sulphur transfer between molten iron saturated with carbon and slags of the CaO-SiO,-A12O3 system. Laboratory experiments cannot reproduce in detail the conditions which prevail in the hearth of a blast furnace, but they will contribute to an understanding of the smelting reactions and perhaps will explain some apparent inconsistencies in the factors controlling the equilibrium distribution of sulphur between iron and slags under reducing compared with oxidizing conditions. The mechanism of a reaction—that is, the individual steps and the sequence in which they occur to produce the overall reaction which is ordinarily observed—must be elucidated to learn which steps are the slow ones, or "bottlenecks," that fix the pace of the process as a whole. In the desulphurization reaction, for example, the overall rate might, in principle, depend upon the rate of diffusion of sulphur in the metal or in the slag, upon the speed of some homogeneous reaction taking place entirely within one of the phases, or upon some heterogeneous reaction taking place across the slag-metal interface. Even some side reaction or the back reaction might have some influence. Evidence on all of these points will be presented in this paper. The rate of diffusion of sulphur in both iron and slag is so slow that it seems necessary to assume that convection provides the mechanism of carrying

Jan 1, 1951

By D. Turnbull, J. H. Hollomon, J. C. Fisher

Application of the concepts of nu-cleation and growth to the analysis of experimental transformation data has led to valuable descriptions of phase transformations, an outstanding example being the transformation austenite —* pearlite which has been examined with particular care by Mehl and co-workers.&apos;-5 In addition to the pearlite transformation, the proeutectoid fer-rite and proeutectoid carbide transformations are known to proceed by nucleation and growth. Martensite, on the contrary, until recently was thought to form by a mechanism involving neither nucleation nor growth; however, extension of standard nucleation theory6 suggests that martensite, bain-ite, and the other products of austenite decomposition all grow from nuclei in the parent phase. The theory that martensite forms by nucleation and growth is strongly supported by recent experimental work of Kurdjumov and Maksimova.7 The concepts of nucleatioli and growth have been fruitful also in providing a sound basis for quantitative theoretical treatments of the kinetics of phase transformations. For example, Volmer and Weber8 and Becker and Döring9 developed the theory of nucleation from fundamental considerations to a point where excellent agreement was obtained with the results of experiments on the condensation of supercooled vapors. As a result of their analysis, the kinetics of vapor-liquid transformations now can be predicted. It seems probable that application of the theories of nucleation and growth to a quantitative study of austenite decomposition similarly will clarify the nature of the individual transfor: mations involved, and will enable the calculation of austenite transformation kinetics. In the present paper, the theories of nucleation and growth are applied to the austenite ? martensite transformation in steels. The analysis begins with a discussion of nucleation in single component systems. Martensite appears to be coherent with the parent austenite, hence the nucleation theory is modified to include the effects of elastic distortion. Nucleation in the two component iron-carbon system then is discussed, for most steels are primarily alloys of these two elements. Finally, M. temperatures and martensite transformation curves are calculated for each of several alloy steels of varying carbon and chromium content, and are compared with those determined experimentally by Lyman and Troiano10 and Harris and Cohen.11 Nucleation Theory NUCLEATION IN SINGLE COMPONENT SYSTEMS6,12-14 The work required for reversible formation of a region of phase within the parent a phase is expressed conveniently as the sum of two terms: W1 = Aa, the product of the area of the interface and the interfacial free energy, and W2 = VAf, the product of the volume of the region and the free energy increase per unit volume associated with the transformation. The total work is therefore W = Aa + VAf. When a is more stable than ß, Af is positive and W increases without limit as the volume increases. The transformation a ?ß does not occur. It is nevertheless true that small regions of phase ß enjoy temporary existence here and there in the a. The equilibrium number of ß regions of given size is proportional to exp(— W/kT) per unit volume of a, assuring that larger (ß regions occur with diminishing probability. When a is less stable than ß, Af is negative and W passes through a maximum as V increases. Assuming for simplicity that regions of ß are spherical, as is true when the interfacial tension is isotropic and there are no elastic strains, W = 4r2a + (4/3)*r3Af The maximum value of W is W* = 16iro3/3Af2 [1] for regions with radius r* = -2o/Af. [2] For single component condensed systems it has been shown14 that the steady rate of nucleation of 0 per unit volume of untransformed a is nearly proportional to exp[- (W* + Q)/kT] where Q is the activation energy for the unit processes of adding or removing one atom from an embryo or nucleus. If To is the temperature at which a and ß are in equilibrium, the rate of nucleation is a maximum at a temperature 0 < T < To where (W* + Q)/kT is a minimum. P regions smaller than critical size are called embryos; they tend to grow smaller and disappear, only exceptionally growing larger. Regions equal to or larger than critical size are called nuclei. A critical size nucleus may grow indefinitely large or may shrink back to a, either process decreasing the free energy of the region.

Jan 1, 1950

By C. W. Washburne

FORMER studies of sedimentary strata have been based upon the mineralogical and mechanical characters of the solid components, rather than upon the open spaces between them. For present purposes let us take another point of view, and consider not the rock material, but rather its cavities, the pores and the fissures or cleaved joints which connect with them. Let us think of the geologic column not as a series of rocks, but as a mass of irregular connecting capillaries. Different parts of the column may be distinguished by the absolute size and by the relative amount of its open spaces. Porosity Each stratum of the column is characterized by a certain porosity, which would be independent of the size of the rock grains if all were of the same shape. Slichter has shown that the percentage of open space in a pile of equal spheres is practically constant regardless of the diameter of the spheres. This is approximately true of clean, assorted sand or gravel, but it is far from being the case with most natural sediments which have a widely variable porosity, the magnitude of which is determined mainly by the amount of fine and of secondary material between the larger grains. The shape of the grains materially affects porosity, round grains leaving more open space than angular or flat grains. The thin plates of kaolin and the fine plastic matter of clay fit quite perfectly when pressed together, and it is probably this close fit, determined by shape of grain, rather than the small size of a grain, that causes the low porosity of ordinary clay shale.

Jan 9, 1914

By Charles A. Colton

The results of a series of analyses extending over a period of three weeks at the Cedar Point Iron Company&apos;s furnace, Port Henry, New York, are given in Tables I and 11. This furnace uses a very pure magnetite and Lehigh and Lackawanna anthracite. The flue leading the gas from the "down-comer" to the boilers was tapped by a 2 inch gas pipe, which carried the gas to the Orsat apparatus. The pressure of the gas not always being sufficient, owing to the small amount made, to force it into the apparatus, I omitted taking samples several days, and with the exception of the last three days of the campaign, made the analyses whenever opportunity offered. I find the Orsat apparatus, as described by Prof. Egleston," to work very well, with one exception. The CO is not absorbed as readily in the ammonia-copper solutiou as he states in his description of the apparatus, as many as 50, and sometimes GO, passes being necessary to absorb all the CO. The power of absorbing rapidly increases as the solution is used, and this would indicate that the more oxygen it contains the quicker will it do the work. Probably the addition of a small amount of some oxidizing agent would remedy this. When the furnace was working in its normal condition, I had no occasion for using the filter, the amount of fume being so small as not to canse any inconvenience. The gas burned with the flame peculiar to CO, and contained just enough solid particles to give it a slight reddish tinge.

Jan 1, 1879