Search Documents

Birmingham - A City With a Future COURTING new industries is the time honored duty of the chambers of commerce; but Birmingham, until recently, has done its courting without the benefit of troubadors. This is all changed now for the iron and steel industry is singing an enticing song about steel priorities for new industries from Birmingham's own mills. Along with the increasing industrialization of Birmingham there has been a marked influx of industry into the Southeast and neighboring areas in the south central states which augurs well for business in Birmingham. This important stronghold of the foundry industry (consuming 95 pct of Birmingham's merchant pig iron in 1950) has been the source of important announcements about additions to steel ingot capacity. The virtual abolition of basing point pricing gives the Birmingham iron and steel industry an advantage in the South's new markets. This means more business for Birmingham, but the problem of raw materials supplies is posed.

Jan 12, 1950

By M. J. Marcinkowski, A. S. Sastri

A detailed compressive stress-strain analysis and transmission electron microscopy investigation has been made of the deformation behavior occurring in a 50 at. pct Ni-Ti (hypoeutectoid) alloy and a 54.5 at. pct Ni-Ti (hypereutectoid) alloy. In the case of the hypoeutectoid alloy, three stages of work hardening are observed. Stage I occurs at a very low stress and is associated with plastic deformation via martensite formation. Stage 11 is characterized by very rapid work hardening and is due to difficulties in causing further deformation in the fine martensite aggregate produced in Stage I. Stage III which occurs at very high stress levels is characterized by smaller work hardening rates and is due to the plastic deformation arising from alternate reconversions of the original martensites to martensites of varying orientation. Rapid quenching of the hypereutectoid alloy leads to very high yield strengths and is related to a fine precipitate dispersion that such treatment brings about. The present investigation represents the final phase of a three-part study directed toward an understanding of the solid-state transformations in near equi-atomic Ni-Ti alloys as well as the deformation mechanisms associated with these alloys. In the first part,"2 to be henceforth referred to as I, it was found that alternate simple shears on {112} planes and in (111) directions convert the parent B2 structure in the equiatomic NiTi alloy into two distinct close-packed monoclinic martensites. All of the marten-sites were of this type, whether they were formed by cooling or by plastic deformation, whether induced to form in bulk samples or in thin foils, or whether examined in the electron microscope at room temperature or below. On the other hand, in the second part of this investigation,3 to be reffered to as 11, it was shown that upon slow cooling to about 640°C. alloys in the neighborhood of NiTi which possess the B2 structure transform eutectoidally into their equilibrium phases Ti2Ni and TiNi3. However, preceding the formation of these equilibrium phases a series of metastable intermediate phases are formed. This paper will set as its goal the elucidation of the remarkable deformation behavior exhibited by NiTi. In particular, Buehler and Wiley4 have found equiatomic NiTi to be surprisingly soft, while Buehler et al.5 have shown this alloy to possess a memory effect: i.e., upon bending at room temperature it will revert to its original shape when heated to above about 50°C. In I it was shown that NiTi was soft in the sense that the yield stress was low; nevertheless, the alloy work-hardened at an extremely rapid rate to very high stress levels. On the other hand, the hypereutectoid alloys with somewhat higher nickel, say 54.5 at. pct (60 wt pct) have enormously increased yield strengths compared to those of the equiatomic alloys. In order to determine the atomistic processes giving rise to the above behavior, it was decided to examine samples that were wafered from bulk specimens deformed in compression to various strains using the techniques of transmission electron microscopy. EXPERIMENTAL TECHNIQUE All of the alloys used in the present investigation contained either 50 at. pct Ni (55.06 wt pct) or 54.5 at. pct Ni (60 wt pct) and were arc-melted in the form of a finger using the same techniques described in I and II. The finger was capsulated in a stainless-steel jacket and swaged at 850°C into rods. Compression specimens 0.300 in, long and 0.200 in. in diam were machined from these rods. In order to completely re-crystallize the samples and remove residual stresses, all of them were capsulated in evacuated quartz, annealed for 1/2 at 1050°C. and then furnace-cooled. Compression tests were carried out in an Instron tensile testing machine covering a range of temperatures from —196° to 200°C using procedures described previously.6'7 In all cases crosshead speed was 0.02 in. per min. Wafers 0.015 in. thick were spark-cut from the cylindrical samples at 45 deg to the compression axes after they had been deformed to the desired strain. These specimens were then spark-planed to about 0.005 in. and then electrochemically thinned for examination by transmission electron microscopy as described in I.

Jan 1, 1969

OFFICERS AND DIRECTORS (The Officers are the President, 6 Vice-Presidents, the Treasurer, and the Secretary) President and Director HENRY DEWITT SMITH' Past President and Director LEO F. REINARTZ President-elect and Director C. E REISTLE, JR

Jan 1, 1955

By Peter Stubbs

Mr. Agelopas is to be congratulated on a fine paper. Although the presentation was simple and concise, you will all appreciate that a great deal of hard work went into the development of this highly successful repair method. Earlier this year Bethlehem invited a group of our people to witness lug repairs at their Sparrow's Point plant. We have since made lug replacements on a trial basis using their method. The repaired moulds are now back in service. We will compare their performance with regular moulds and with moulds repaired by a technique developed by Dofasco weld shop personnel. I would like to explain briefly some of the various types of ingot mould repairs presently undertaken at Dofasco. The first problem will be familiar to most of you. The lower inside edge of a mould wall may be damaged by spalling, a runout or by the washing action of steel deflected from a badly worn stool cavity. We repair this type of damage by welding.

Jan 1, 1972

By E. P. Mathewson

THE OLD Pueblo smelter is being dismantled after 43 years of continuous operation, from 1878 to 1921. It was built by Mather and Geist, on a bluff overlooking the Arkansas River just below the, city of Pueblo. At the time of its construction Pueblo was considered a most favorably situated town for a custom smelter. Coal, coke, fuel, limestone, iron ore, lead, silver, and, gold ores were plentiful. It was a "downhill pull" from all directions to Pueblo. Labor, both common and skilled, was plentiful and efficient. Leadville was in bonanza and there were not sufficient furnaces in Colorado to handle the ore offered. The plant prospered from the start. It soon required more capital; so the owners; with the assistance of Thomas Nickerson of Boston, at that time prominent in the affairs of the A., T. & S. F. railway, formed the Pueblo Smelting & Refining Co. About this time, also, very heavy shipments of rich silver ore from New Mexico began to come in. Agencies were established for the purchase of ores in the most important mining camps in the country from Kingman, Ariz., to Butte, Mont. Highly siliceous silver-bearing ores from Butte were shipped to Pueblo in train loads. This was used chiefly in the concentration of leady mattes. RECOLLECTIONS OF MR. GEIST, FOUNDER OF PLANT Mr. Geist is living in Guadalajara and has sent the following brief letter: "Early in 1878 the firm of Mather & Geist, which had been operating in Utah and had then closed their smelter there, after diligent search for a new location selected Pueblo. We erected the first smelter in the valley, blowing in the first furnace in 1878. Mather & Geist carried on until January, 1882, when they transferred all their business to the Pueblo Smelting & Refining Co., which had been organized in December, 1881. Full details of this transfer are given in the enclosed Report, which was issued early in 1882, for the purpose of interesting more capital, in which we succeeded admirably. "I personally did all the work of manager and super-intendent, some job in these days. My technical quali-fications were that I was a member of the class of 1866, Yale Sheffield Scientific. I was born in 1848, so was the youngest member of the class.

Jan 11, 1923

By Howard L. Hartman

There is reason to believe that ventilation systems so far devised for use with continuous mining machines fall far short of success. This is vividly demonstrated to anyone who has observed in a continuous miner section the localized ignitions of pockets of gas and the generation of dense clouds of dust by the cutting head of the machine. The alarming frequency with which major ignitions and disasters continue to occur in modern mechanical mining and the rise in incidence of pneumoconiosis serve as reminders that our ventilation systems are far from achieving the ultimate in providing protection from either short-term explosions or long- term dust diseases, both of which take lives. Human safety is the main concern in ventilation. But in this day of high-priced labor, let us not forget human comfort, either, for this is a major factor in motivation toward high productivity. The failure or inadequacy of most mine ventilation systems in providing the kind of working conditions at the face that are conducive to productive as well as safe operation is an indictment of our environ- mental control program in mining generally.

Jan 3, 1962

By Eugene McAuliffe

The mining press, as well as certain federal and state bulletins, refer from time to time to the relative hazards that attach to loading bituminous coal by hand when compared with the so-called "mechanical loading" process. Much of the coal coming under the head of hand-loaded coal is won in part by the use of machinery; the coal-cutting machine is in general use, the electric power drill employed to a lesser extent. Therefore it may be said that the principal difference in the process employed, mechanical loading versus hand loading, lies in the fact that some type of loading machine is employed in the mechanical loading process to lift the coal from the face of the room, place or entry, after it is mined, placing it in the pit cars for transport to the tipple. It is a common practice to compute accident records on the basis of tons mined per fatal and per nonfatal accident, disregarding the fact that it is possible to produce by the aid of coal-loading machines the same daily, monthly and annual tonnage with a much smaller force than is required where the coal is all shoveled by hand. Inasmuch as the men who are released by the substitution of machinery for hand labor must find employment elsewhere, suffering some measure of hazard in their new occupation, we are of the opinion that the true relative hazard that attaches to the processes of mechanical loading and hand loading can be determined only by using as the basis of comparison "man shifts worked" or "hours of exposure" experienced per accident. The Union Pacific Coal-Co., beginning with the year 1929, undertook to maintain a true record of man shifts worked per compensable accident, giving equal weight to fatal and nonfatal accidents. Accidents lacking sufficient severity to come under the compensable terms of the Workmen's Compensation Act were not included in the compilation, the Act providing that "no compensation, except the expense of medical attention, shall be allowed for the first seven (7) days of disability, unless the incapacity runs beyond the period of twenty-one (21) days, in which case the compensation shall run from the time of the injury." With the further thought that all accidents suffered by employees engaged in any service, in or about the place where the loading process

Jan 1, 1931

By Thomas D. Henderson, Donald E. Crowell

INTRODUCTION This paper presents a "case history" of the steps taken to estimate capital and operating costs for a typical porphyry copper concentrator of ±9,070 metric tons (10,000 short tons) per day capacity. The concentrator described herein is hypothetical, but is based on experience and is, in effect, a composite of several actual projects. The numbers used are illustrative only and do not represent actual costs at any particular concentrator. These numbers are, however, representative of typical milling costs at one point in time, and. are sufficiently accurate to illustrate the cost estimating procedures described in this paper. It is not possible to publish actual, current milling costs and, in any event, actual cost figures quickly become meaningless in today's economic situation with various costs all rising at different rates. The paper is divided into three parts: (1) order-of-magnitude estimate, (2) feasibility study estimate, and (3) discussion of differences between estimated and actual costs.

Jan 1, 1978

By Edmund C. Pechin

THE writer approaches this subject with a great deal of diffidence —first, because it is utterly impossible to treat it satisfactorily within the limits of a paper, and, secondly, because the larger development is of so comparatively a recent date as to make authoritative data on some interesting points unavailable. For over one hundred years small charcoal-fnrnaces have been in existence, at widely scattered points, making a few tons of iron daily, and then gradually increasing to a daily output of, say 10 to 12 tons, as the market widened. With the exhaustion of local supplies of wood, inaccessibility to market, and sharp competition, bringing lower prices, many were compelled from time to time to make temporary stops, and finally to cease altogether. During the first half of the century there were at different times in operation between 75 and 90 charcoal furnaces. The last Directory of the Iron and Steel Works of the United States (1890) gives 19 as the number of charcoal-stacks in Virginia. Of these several are cold, and, it is

Jan 1, 1891

J. T. LITTLETON, JR., ? Corning, N. Y. (written discussion?).-This. discussion will add little that has not been brought out but will show how the problems encountered in the Corning Glass Works were overcome. The chief points of consideration in any equipment are, first, the work the equipment is called upon to do; second, the installation; and, third, the man who will use it. These three points should determine the type of apparatus adopted. If only rough measurements, merely a little better than the eye, are desired, the cost of the instruments should be considered; but if accurate temperature control is necessary, the cost of the equipment deserves only small consideration. There is no question that the real problem for any factory is the installation, making sure that the elements really give the temperatures desired; also, the instruments must be so designed that any man can use them.

Jan 12, 1919

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By F. R. Van Horn

WALLACE MCKEEHAN, Douglas, Ariz. (communication to the Secretary*).-In going over this report, which I have done very carefully, I find that the summary as composed deals with the various problems almost entirely from the employer&apos;s standpoint and that practically no consideration is given to the employee&apos;s point of view. An experience of 3 ½ years as safety inspector, and almost 30 years as workman-and official, has convinced me that any plan for the betterment of working conditions which will achieve any degree of success must give the workmen their share of responsibility and allow them full participation. The company may finance and direct the movement, but its ultimate success depends upon the support given by the workmen. The cooperation of the men doing the actual work is so essential that all writers insist that this must be secured, but they do not agree as to how this can best be done.

Jan 4, 1917

A. O. GATES, Salt Lake City, Utah (communication to the Secretary*).-The writer is delighted by the results shown in Mr. Bell&apos;s paper, which prove in an experimental way different from that followed by the writer&apos; that "the work clone in crushing is proportional to the surface exposed by the operation," per Rittinger&apos;s Law. Mr. Bell&apos;s work was all clone in commercial types of crushing machines, while my work was clone in a testing machine; his work represents fully one hundred times the expenditure and time that my work represented; a great number of tests were made by his organization to determine single points, while I was obliged to depend on the general trend of a curve for results; we agree absolutely that "Kick&apos;s law," for which Mr. Stadler was sponsor, does not apply to rock crushing. While my work indicated the reliability of Rittinger&apos;s theory, Mr. Bell&apos;s work clearly establishes the reliability and makes it Rittinger&apos;s law.

Jan 5, 1917

By M. E. Learmont, I. Iwasaki

Grinding with steel media adversely affects the flotation response of galena. Electrochemical measurements, flotation tests, and AES, XPS, and STEM examinations were employed to identify interactions between galena and mild steel. Iron oxide, hydroxide, or sulfate species that formed on the galena surface upon contact with mild steel decreased its floatability, with the time of contact and aeration condition affecting the severity of the flotation depression. Parallel tests performed with an active metal, magnesium, indicated that floatability was also affected by the presence of a surface coating involving lead species.

Jan 1, 1985

By Peter Soo

Pvestrained Ferrovac E iron has been neutron-irradiated at approximately 90°C to an integrated flux of 1020 nut (E > 0.82 mev]. The irradiation was found to produce an incveased temperature dependence of the flow stress in addition to a greatly increased athemal stress. Measurements of the flow stress and stress relaxation, from which the activation volume and activation energy for slip were deduced, show that neutron irradiation changes the rate -controlling slip process to one based on dislocation interactions with tetragonal distortions which are Produced around submicroscopic interstitial loops in the lattice. The study indicates that without prestraining prior to irradiation the chances of detecting a change in the rate -controlling slip process are greatly reduced because in the initial stages of slip a substantial fraction of the radiation defects are swept out of the slip plane by gliding dislocations. Thus, activation parameters which are subsequently measured are representative of a greatly reduced defect density and would not differ appreciably from those for unirradi-ated material. The large increase in the athermal component of the flow stress is probably connected with the presence of depleted zones in the lattice which are introduced by irradiation. ALTHOUGH fast neutron-irradiation has not been observed to markedly alter the activation parameters for slip in bcc metals,&apos; small but significant changes do occur. Most experimenters agree that irradiation predominantly increases the athermal component of the yield stress.&apos;-= In addition to this, Laidler and smidt7 have shown that in iron irradiated to 5 X 10" nvt and molybdenum irradiated to 10" nvt, changes occur in the activation volumes for slip. A similar conclusion has been reached by Milasin and Malkin8 for irradiated iron. Work by Ohr et a1.5 shows that for Ferrovac E iron, irradiated to 1.2 X 1016 nvt, small increases in the activation energy for slip also occur. So far these changes in the activation parameters have not been explained on a firm theoretical basis. One important factor which would minimize the chances of detecting a change in the slip mechanism upon irradiation is the presence of "channeling" which has been observed in molybdenum,9 niobium,10 and iron.11These channels are formed by gliding dislocations which sweep irradiation defects out of the active slip planes and thereby create zones in which continued dislocation motion is encouraged. The activation parameters for the dislocations gliding in the defect-free channels would, therefore, be similar to those for unirradiated iron and a change in the rate-controlling slip process would be difficult to detect. In the present work, an attempt has been made to reduce the effect of uneven deformation on the measured activation parameters for slip in neutron-irradiated Ferrovac E iron polycrystals, so that a more realistic assessment of the effects of neutron-irradiation could be made. Primarily, the experiments involve the irradiation of specimens which had been prestrained to 9 pct elongation at room temperature prior to insertion into the reactor. It was hoped that the introduction of a large number of evenly distributed dislocations would substantially decrease any channeling effect which might otherwise occur. MATERIAL AND EXPERIMENTAL PROCEDURE The starting material was vacuum-melted Ferrovac E iron, an analysis of which is given in Table I. The standard tensile specimen had a gage length of 1.125 in., a cross-sectional diameter of 0.120 in., and a re-crystallized grain size of 1.2 x 10-3 in. All tensile tests were conducted on a floor model "Instron" tensile machine at a strain rate of 3 x 10-4 per sec. The irradiation of the prestrained specimens was performed in the Brookhaven High Flux Beam Reactor to an integrated flux of 1020 nvt (E > 0.82 mev) at a temperature of about 90°C. All specimens were excap-sulated in high-purity aluminum sheaths which were lightly swaged around the samples to ensure good thermal contact. Subsequent measurements on the irradiated specimens showed that within experimental accuracy the swaging had not deformed them. EXPERIMENTAL RESULTS Fig. 1 shows the flow stresses for a series of unirradiated control samples. In order to produce a comparable dislocation substructure throughout the test sm range, all specimens were prestrained

Jan 1, 1970

By J. P. Zannaras

If we assume that testing of the model started at time C, that time t2 was the instant at which the elastic limit of the material was passed at the points of the maximum stress, and that at time t3 the failure of the model was completed as shown in the typical photograph (Fig. 1), then actually the photograph shows the final results of what took place between time t2 and t3. By the principle of similitude all conclusions drawn from the behavior of the model were applicable and valid for actual mine roofs up to the time t, after time t, motions and friction came into play during the destruction of the model. The events between t2 and t3 and the photograph itself are not representative of the events expected in an actual mine roof unless corrections imposed by the principle of similitude are made.

Dec 1, 1956

By W. D. Forgeng, R. L. Folkman, D. C. Hilty

The solubility of oxygen in molten Fe-Cr alloys has been determined at 1550° , 1600°, and 1650°C for alloys containing up to alloyshasbeenabout 50 pct Cr and found to decrease as chromium increases to 6 pet and then to increase gradually. Phase relations in the Fe-Cr-0 system at steelmaking temperatures have been evaluated and two previously unreported oxides have been identified. OPERATIONS in the melting and refining of chromium steels are dependent to a major degree on the reactions of chromium and iron with oxygen and are primarily directed toward controlling and modifying these reactions to secure maximum advantage in the utilization of chromium. Although fairly effective practices have been developed empirically, understanding of the specific reactions is limited. Moreover, the ability of molten steel to dissolve oxygen that subsequently precipitates as oxide inclusions during solidification is well known, so that clarification of the effect of chromium on the nature and mechanism of formation of these inclusions is desirable. Study of the problem indicated that increased knowledge of the fundamental Fe-Cr-0 system is essential to further technical and economic improvement. Consequently, an investigation of the influence of chromium on the solubility of oxygen in molten iron and of phases and phase relations in the Fe-Cr-0 system was undertaken at the Metals Research Laboratories of the Electro Metallurgical Co. as part of a general program on the effective utilization of chromium in chromium steel production. Experimental Procedure All of the experimental runs made during this investigation were carried out in the rotating crucible induction furnace which has been described in detail in a previous publication.&apos; In review, the principle underlying this furnace is that rotational forces in the crucible cause the molten metal to assume a concave shape in such a manner that the slag is contained in the molten metal cup, thereby minimizing slag/crucible contact and subsequent reaction. Practically all of the heats were melted in commercial-quality magnesia crucibles of the type usually furnished for laboratory induction furnaces. All of the runs were made under an argon atmosphere after the furnace chamber had been degassed. Bath temperatures were controlled by Pt—Pt-10 pct Rh thermocouples. The basic furnace charge consisted of a premelted 12 to 15 lb electrolytic iron slug which had been cast to a shape convenient for fitting into the rotating furnace crucible. A typical analysis of the electrolytic iron slugs is given in Table I. For certain runs, it was desirable to melt down charges containing high initial chromium contents. In these cases the chromium was added to the electrolytic iron during the premelting operations. Chromium was added to the rotating furnace bath in the form of electrolytic chromium of the analysis given in Table 11. In all of the constant temperature runs, the standard procedure was to melt down the electrolytic iron or alloy slug under vacuum, admit argon to slightly greater than atmospheric pressure, and adjust rotational speed to develop a well formed "cup" on the bath surface. The melt was then saturated with oxygen by an addition of ferric oxide and the temperature of the bath adjusted to within +5°C of the desired level. At this point the heat was permitted to come to equilibrium prior to sampling or further addition. This time interval was varied from 15 min to 2 hr but generally was about 20 min. After sampling, the desired chromium addition was made and the bath again equilibrated prior to subsequent sampling. This cycle of addition and sampling continued for the duration of the run which lasted from 4 to 8 hr. At the end of this period, power was shut off and the bath allowed to solidify in the furnace. Quenched metal samples were taken from the equilibrated melts by means of the "Taylor sampler" which has been described by Taylor and Chipman.&apos; Before being submitted to chemical analysis, all samples were carefully examined for surface slag occlusions and cold shuts. Later in the study, each sample was radiographed and examined metal-lographically in cross-section to determine the presence of internal defects. On the basis of these examinations, sound and apparently clean specimens were selected from the Taylor samples for chemical analysis.

Jan 1, 1956

By M. E. Wadsworth, J. S. Cho

The kinetics of silicate adsorption from aqueous colloidal (SO2 . nH2O) silicate sols on thoria (ThO 2) surfaces were determined at 100, 150 and 200°C in an autoclave system. The amount of chemisorbed silica on the thoria surface was determined by means of infrared spectroscopy. First order kinetics were observed in all cases with the anomalous result that the first order rate constant was found to vary with the initial amount of silica added to the system. These results have been correlated quantitatively by means of a strain model of adsorption involving two types of surface silicate bonding, both of which may be readily observed in the infrared spectrum. Initial adsorption occurs rapidly to produce one type of surface silicate followed by a slow transition to a second type of surface bonding, the latter transition representing the slow step in the adsorption process. Initial interest in silicate adsorption on thoria arose from the dispersive effect silica has on finely divided thoria in aqueous suspensions. Spaepen et al studied the equilibrium adsorption of silica on thoria and noted increased adsorption up to approximately 215°C with a notable decrease in adsorption at temperatures above 215°C. Similar results were observed by Cho and Wadsworth2 who identified two types of surface silica by infrared spectroscopy. At temperatures of 100°C and above, rapid initial adsorption occurred producing a surface species with maximum infrared absorbance at 9.4 After extended periods of time, the 9.4 species converted to a more strongly bonded surface silicate with maximum infrared absorbance at 10.3. The latter was very strongly bonded and difficult to remove by desorption in hot distilled water, while the 9.4 species could be removed more readily by similar treatment. The 9.4 and 10.3-p species were distinguishable from free unadsorbed silica which had maximum infrared absorbance at 9.1 The kinetics of the formation of the strongly chemisorbed silica (10.3) on thoria as determined by infrared examination are presented in this study. EXPERIMENTAL PROCEDURE As a source of silicate, Ludox SM (16.36% SiO2) or Ludox HS (30.25% SO2), DU Pont colloidal silica in aqueous suspensions, was added directly to a thoria slurry made up of one liter of distilled water and one gram of thoria. The thoria used was designated D-16-650 and was received from the Chemical Technology Div. of Union Carbide Nuclear Co. It was prepared by firing thorium oxalate at 650°C. The D-16 thoria had a surface area of 32.4 ± 0.6 sq m per g as determined by nitrogen adsorption.* This thoria &apos;Determined by Unlon Carbide Nuclear Co., ORNL. had a total adsorption capacity for silicate of approximately 19.4 mg of silica per gram of thoria.1 This amounts to approximately one SiO2 molecule for every surface thoria site. In all cases in this study.

Jan 1, 1963

By Douglas W. Fuerstenau, Kalanadh V. S. Sastry

Based on an analysis of green pellet size distributions and kinetic data on ball growth with taconite concentrates, a ballability index has been developed to quantify ball growth behavior as a function of moisture and bentonite additions. The applicability of the ballability index to such other particulate materials as pulverized limestone and ground magnesite is shown.

Jan 1, 1973

In an address delivered at Atlantic City, N. T., Dec. 5, 1918, M. L. Requa, General Director, Oil Division of the United States Fuel Administration, said: We face a new era with all its uncertainties. We have arrived at the period of reconstruction and are face to face with the problems concerning which we have so often speculated during the past four years. In all this reconstruction work the United States must bear an important part. We are looked upon to lead the way, to blaze the trail and our actions will have a profound influence upon the rest of the world. If we are to succeed, even in part, we must not be ashamed to practise economy; we must not despise the clay of small things; the little savings; we must have the closest cooperation between Government and industry. Just as truly do we need civic awakening. All that we have ever fought for, the liberty of the world, is comprehended in the ballot; and yet how lightly we have held this great privilege! We need, if we are to reap in full the benefits of the past 18 mo., an awakened civic consciousness; a jealous guarding of government; a resolution that we will, each and all, perform to the full the duties imposed upon us by Democracy; that we will perform more completely the obligations resting upon us as citizens. During the war, industry, through sane cooperation and intelligent effort, has accomplished results possible of attainment in no other way. Government and industry have worked hand in hand and pointed the way o to future activities which, if realized, can but be most highly beneficial to all. If Government and industry are to fulfill their respective duties satisfactorily, it is obvious that there should be complete mutual confidence. Industry must not attempt to "put something over"-and Government must treat with industry upon the high plane that has characterized the public utterances of the President during the war. The individual who cannot conform to these high ideals should have no place in industry, and equally no place in Government. If the dignified and broad princi-

Jan 2, 1919