Search Documents

By Patterson B. G

The small party of mining men who formed the original Mount Morgan Syndicate in 1882, commenced operations on the top of the mountain with what were practically nothing more than small hillside quarries, It was not until 1891 that underground stoping began, and open-cut mining therefore commenced with the commencement of operations. This hillside quarrying, however, seems to have been quite haphazard and unsystematic ; there is no trace or sign of any properly devised mining scheme. This can be seen plainly enough from an examination of old mine plans; for in less than five years after stoping was; adopted, the open-cut was down into the stoped-out ground. The following table, prepared from these old plans, shows the downward trend of the excavation in the past fiftyseven years:-

Jan 1, 1939

By Juan M. Pestana, Jeremy M. Gasser, Cuneyt Gokmen, Paul J. Sabatini, William Tanner, Daniel J. Woeste

An access pathway and working platform were designed and constructed for equipment access for a Deep Soil Mixing (DSM) pilot study over a coal combustion residual (CCR) surface impoundment (SI). The DSM pilot study was conducted to evaluate slurry mix designs and construction techniques for installing DSM columns up to 95 feet deep. Two-dimensional (2-D) limit equilibrium and 2-D finite element analyses were used to evaluate multiple failure mechanisms including: (i) bearing capacity, (ii) punching shear of mixed ground and underlying CCR, (iii) effect of fluidized DSM columns on working platform stability, and (iv) liquefaction. The analysis results were used to design ground improvement required to increase bearing capacity and stability of the CCR under the proposed equipment access route. A long-reach excavator was used to perform shallow bucket mixing and walk onto the CCR SI atop previously mixed cells following a minimum cure time and acceptance of quality control test results. Prior to mobilizing the DSM rig, a static load test was conducted to evaluate performance of the working platform. Both the access pathway and working platform demonstrated acceptable performance under the design loads during the DSM pilot study. This case study emphasizes the economic and safety benefits that can be realized by appropriately designing critical temporary work items such as access pathways and working platforms in difficult ground conditions. INTRODUCTION A Deep Soil Mixing (DSM) pilot study was conducted at a coal combustion residual (CCR) surface impoundment (SI) to evaluate slurry mix designs and construction techniques for closure design of the SI (Site). Sluicing of CCR at the facility ceased and closure will be initiated based on requirements in the final United States Environmental Protection Agency (USEPA) Rule for Disposal of Coal Combustion Residuals from Electric Utilities, 40 CFR 257, effective October 19, 2015. The proposed closure approach involves constructing a DSM containment structure (DSM Wall) to separate the SI into two areas: (i) a closure by removal area; and (ii) a consolidate and cap-in-place area. The proposed DSM Wall would retain the CCR within the consolidated closure footprint and provide a barrier between the two areas of the SI. The predominant CCR in the SI where the pilot study was conducted were fly ash and bottom ash. CCR materials in surface impoundments are generally soft and saturated as a result of being sluiced into place and can present stability and safety challenges when performing earthwork activities.

Jan 1, 2019

By L-B Fu and J Tan, J H. Wei, N Tian

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Kendenggaoer-Kuokuqueke region lies in the western part of Chinese North-western Tianshan. New laser ablation inductively coupled plasma mass spectrometry zircon U-Pb geochronology for five separate granitic plutons for this region reveal two distinct intrusive periods: late Devonian (367~361 Ma) and late Carboniferous (315~301 Ma). These intrusions all share an arc-like geochemical affinity (ie enrichment of large ion lithosphere elements and negative anomalies of Nb, Ta and Ti). In situ zircon Hf isotopic compositions further differentiate the magmatic cycle, with the late Devonian intrusions yielding more depleted eHf(t) (+1.47~+6.54) composition than the late Carboniferous intrusions (eHf(t) = +4.95~+9.79). These geochemical data suggest that they might be mainly derived from different source regions and the tectonic setting was transformed into post-collisional in the late Carboniferous. As in many significant porphyry-ore districts, this dramatic tectonic reconfiguration, combined with melting of an evolved crust, resulted in genesis of metal-bearing melts. Furthermore, we can show that Neoproterozoic mafic juvenile lower crust intruded by mantle-derived melts and/or partial melting of slab material generated hybrid primary magma during subduction of the Palaeo-Junggar oceanic crust in the late Devonian. Whereas underplating of mantle-derived magma contributed more to the Late Carboniferous post-collisional magmatism.CITATION:Tian, N, Wei, J H, Fu, L-B and Tan, J, 2015. Timing and geodynamic setting of the late Palaeozoic polymetallic mineralisation in Chinese north-western Tianshan – insights from geochronology and petrogenesis of granitoids , in Proceedings PACRIM 2015 Congress, pp 171–174 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By William J. Douglas

This document describes the development of a conventional mining equipment data base, and an approach for conducting industrial engineering studies of arbitrary mining systems employing network techniques. Data was acquired through underground time studies. Each member of a four-man field team was assigned to a specific machine during each shift for which observations were conducted. Using digital wrist watches and networks describing the man-machine interactions, all events occurring luring the course of each shift were recorded on cassette tapes. The tapes were transcribed, coded, keypunched, and validated using computerized editing techniques. The resulting data files were processed to provide statistics relating to activity durations and event frequencies. The results were used to evaluate operator, machine, and system performance for each section which was observed. Equipment, reliability, and maintainability analyses were conducted using the industrial engineering data files in conjunction with historical information collected at the mine site.

Jan 1, 1976

By Raja V. Ramani

Discussion in this section of the Handbook is limited to the working environment of miners, the mine workers themselves, and the machines used in mining (Fig. 11.0.1). The contents emphasize personnel health and safety aspects and engineering design and control practices to ensure a productive health and safety environment. Reference is to the health and safety of the individual miners as well as to the safety of the working environment. This Handbook also contains references to health and safety regulations in Chapter 3.2 and environmental protection in Chapters 3.4 and 7.3.

Jan 1, 2008

By The Staff

Introduction It is the purpose of this paper to discuss a number of the metallurgical improvements in the technology of copper-nickel ore treatment which have been introduced during recent years in the plants of ?the International Nickel Company of Canada, Limited. In common with other ore treatment processes, the procedure for extracting nickel and copper is changing almost continuous! y. These changes are necessitated by reason of changes in ore grades and characteristics, rising material and labour charges, and the constant drive to maximize metal recovery and to minimize production costs. It is not possible to present a comprehensive list of all the changes made, and only a selected number of the improvements in the milling, smelting, and refining operations are covered. It should be clearly understood that some phases of the procedures described have been pioneered by others in kindred fields and due acknowledgment is given to their foresight and efforts. Articles have been published over the years describing the operations of the International Nickel Company plants and the reader is referred to the Engineering and Mining Journal, Vol. 130, No. 9, November 10th, 1930, and to the Canadian Mining Journal, Vol. 58, No. 11, November, 1937, and Vol. 67, No. 5, May, 1946. Other references are the Transactions of this Institute, 1932, 1938, and 1946; Metals Technology, American Institute of Mining and Metallurgical Engineers, February, 1938, and Canadian Chemistry and Process Industries, April, 1940.

Jan 1, 1948

The Development of a Non-Roasting Technology for Polymetallic Gold and Silver-Bearing Sulfide Concentrates Treatment

Sep 13, 2010

By Henry G. Granger

I. INTRODUCTION. REPEATED failures in attempts to work gold-bearing gravels by means of suction-dredges have created the impression that this method is impracticable. The suction-dredges have failed from three special causes excessive wear and frequent breakage of pump-shell, runners and liners; inability to dredge compact gravel which would ,not. readily move towards the intake; and, most important of all, closing. of the suction-pipe by stones too large to enter it. In my opinion, all three causes of trouble may be remedied: the first, by making stronger the parts most liable to wear and breakage; the second, by means for loosening the gravel at the intake; and the third, by sufficiently... Increasing.. the diameter of the suction-pipe. In suction gold-dredges, this diameter has not usually exceeded 10 or 12 in.; whereas there are few profitable gold-fields which can bee considered dredgeable, in which stones more than' 12 in. in diameter, are-.not frequently encountered. II. AN EFFECTIVE SUCTION-DREDGE. In harbor-operations, much larger stones are handled by suction-dredges.., The large dredge of the Henry Steers Contracting Co. worked for nearly four years at League Island, Philadelphia, where it sucked up, passed through the pump, and forced through 3,700 ft. of discharge-pipe; gravel containing boulders up to 200 lb. in weight. This was done with no bad breaks and few shut-downs. The cutter; and liners were the only parts liable to damage, and these were easily replaced with brief interruption of work. The chrome-steel liners are said to have lasted from six to nine months. I am informed that this dredge worked continously for nine

Apr 1, 1909

To George Orwell the year of 1984 was the inspiration for a book. To most New Zealanders it was the year that the fourth Labour Government was elected to power. It was also the year that the review of mining legislation commenced. While Orwell's book and the election of Labour are clearly events of some historic note, one could be excused for classifying the review of minerals legislation somewhat differently in terms of its present achievements! Since the review began it has led a tortuous path through a rapidly evolving policy environment to a point three years hence where no major policies have been determined.

Jan 1, 1987

By R. V. Ramani

The industrial hygiene and safety aspects with internal combustion engines in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. This bibliography, therefore, is a compilation of references from interdisciplinary sources pertaining to diesels and related areas. Related areas are defined as those concerned with: (i) mine ventilation system design and operation; (ii) description, measurement, modeling and monitoring of mine atmosphere contaminants, and (iii) tests, standards, selection procedures, and operational practices for internal combustion engines in underground mines. References cited from source materials span the years 1900 to early 1977. Total number of references cited is 511. Subjective criteria governed the definition and selection of references. Therefore, this bibliography is not claimed to be all-inclusive nor does it purport to be an exhaustive search of all sources.

Jan 1, 1977

An understanding of the origin of mineral deposits and their relationship to local and global geotectonics is essential if regional targets for mineral exploration are to be chosen. Volcanism, metamorphism and tectonism are especially significant for the origin and emplacement of mineral deposits, which, far from being fortuitous oddities of nature, occupy well defined positions within distinctive lithofacies. Thus, suggestions for mineral exploration targets can be made taking into consideration the position of 'fossil' convergent and divergent plate tectonic boundaries to indicate areas of specific types of mineralisation. To be borne in mind, though, that level of exposure, time and location of magma generation are all additional and important controlling factors. To further understand the importance of the above parameters, one must refer to the concept of paired metamorphic belts (Miyashiro 1973) which develop during an orognic cycle. These belts are generally constructed in such a way that an ophiolite type complex with metamorphic grades related to high pressure and moderate temperature regimes is flanked by an area of calc-alkaline volcanism and granitic activity with metamorphic grades within a region of high temperature and low pressure. The former situation is usually the seat of primary magmatic mineralisation, whereas the latter contains base metal. Deposits of acid plutonic and volcanic association. As will be seen later, this particular metamorphic-volcano-orogenic situation is well developed in some parts of New Zealand. For the present purpose a distribution of potential ores as related to plate tectonic processes is given below:a) Divergent plate boundaries: primary magmatic Ni-Cu, Pt,Cr, PeS2 and Cu, Pb,Zn in hot brines-hydrothermal environments Mn deposits.b) Convergent plate boundaries: stratabound Cu-Fb-Zn-Ag of felsic volcanogenic association. Porphyry eu-Au of island arc type, porphyry Cu-Mo of continental type. Cu, Au, Y, Sn, Hg, Sb of vein type and replacement lode related to granitic activity.c) Au of hydrothermal vein association, related to late dynamo-metamorphic events. By virtue of ocean floor spreading, regions of divergent plate boundaries are eventually juxtaposed or welded n to areas where plate collisions occur. This is then followed by partial melting due to various causes, just above the descending plate; thus creating a zone of acid to intermediate magmatism. The final picture is that of an orogenic zone with the paired metamorphic belts outlined above.

Jan 1, 1976

By D. Harrington

"FOREWORDVirtually all government agencies undertook many additional responsibilities during the period immediately preceding World War II; these responsibilities increased vastly in importance and scope after the actual declaration of war following the attack on Pearl Harbor. The Bureau of Mines was one of the agencies thus affected, and it was called upon to perform many duties foreign to its normal peacetime activities.The Health and Safety Division of the Bureau of Mines, at that time designated the Health and Safety Branch, was given several important and difficult duties and responsibilities of an unusual nature because of the war while of necessity-continuing its normal functions of assisting the mineral industries in the preservation of life and health and the protection of property, this being of especial importance in wartime because of the pre-eminent importance of having maximum output of essentially all types of mineral products. Some of these additional functions were given to the Health and Safety Division because the organization of the Division, with its field set-up dividing the Nation into districts with competent, experienced personnel in charge of its work, provided the nucleus of personnel and procedure through which rapid and smooth expanded functioning was feasible.In addition to the responsibilities directly attributable to definite war activities, such as the administration of the wartime Federal. Explosives Act and the Mineral Production Security Branch a new branch (then designated division) was formed to investigate coal-mine health and safety problems after the enactment of the Federal Coal-Mine Inspections and Investigations Act, which became a law on May 7, 1941, but which actually began to function actively after the declaration of war in December 1941.The purpose of this publication is to provide a brief historical record of the activities of the Health and Safety Division as a whole and of its individual branches during the war. The detailed record has been filed in the Archives Building, Washington, D. C."

Jan 1, 1949

By Pratt Rogers, Aaron Young

Digital transformation (DT) is the process by which entities adapt themselves to modern technology. As digital technology becomes more prevalent (automation, cameras, sensors, touchscreens, artificial intelligence, etc.), there will be increased pressure on companies to leverage it for additional gains. For many companies in the mining industry, this will involve overcoming a steep learning curve. Furthermore, as the long-term success of the mining industry is dependent on a labor force with new skills (data management, analytics, digital literacy, etc.), new curriculum will need to be appended to the mining engineering discipline. This paper considers the mining industry’s need for DT. Then, it presents a three-part review of the foundational components of the DT process–ubiquitous data, connectivity, and decision making. Finally, it provides a discussion on the future of DT in mining as well as a research direction, which identifies the need of academia to provide support for mining companies in the form of both research and the education of digitally literate, dynamically capable mining engineers into the coming decades.

By Sara J. Davenport

With the increased demand for mercury incident to preparations for national defense and the reduction in imports from some of the usual sources owing to war conditions, many small mines in the United States Pure now being worked that ordinarily would be unprofitable. This is indicated by the following table on mercury produced in the Unite States in 1939-40 (1)4/

Jan 1, 1941

The 20th annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Westin La Paloma in Tucson, AZ, on Saturday, Dec. 7, 2002. This year’s inductee, guest of honor and featured speaker is J. David Lowell, one of the preeminent exploration geologists of the past 30 years. Among his most recent discoveries is the world-class Pierina gold deposit in Peru, currently owned and operated by Barrick Gold. As representatives of mining heritage, the Hall of Fame will induct Howard Allen Twitty, Sr., and Bernhardt Rohe. Twitty was a respected public lands attorney. He made significant contributions to the mining industry by representing several major companies in many court cases. He was also the author of numerous papers on mining law. Rohe was managing director of Peñoles. In that position, he helped guide the Mexican mining company for its growth into the international mining company that it is today.

Jan 1, 2002

By R Long

The founder of social psychology is sometimes identified as Kurt Lewin. In a 1947 article, Kurt Lewin coined the term ‘group dynamics’. He described this notion as the way that groups and individuals act and react to changing circumstances. Lewin theorised that when a group is established it becomes a unified system with unique dynamics that cannot be understood by evaluating members individually. The discipline of social psychology really emerged out of World War II and tackled questions associated with human judgement and decision-making by the Nazis. For a comprehensive look at the development of social psychology look at Abelson, Frey and Gregg (2004).Social psychology is concerned with the way social arrangements affect human judgement and decision-making. What the author has done is apply the knowledge of this new discipline to an understanding of risk, safety and leadership. This paper will explain some of the developments in social psychology, such as the discovery of the bystander effect, Groupthink, bounded rationality, heuristics, risk homeostasis and the Milgram effect.The social psychology of risk tackles the way decisions are made about risk in their social context. Unless organisations understand that decision-making is socially conditioned, they are unlikely to be able to tackle the complexities of culture change or the development of risk maturity.The paper will offer a new understanding of why people do what they do, how risk makes sense and why a ‘dumb down’ approach to safety is dangerous. A model will also be presented that shows the pathway to risk maturity.CITATION:Long, R, 2016. The social psychology of risk, safety and leadership maturity, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 31–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

J. H. Lord (Geological Survey of Western Australia): During the last few days in Kalgoorlie here we have heard on various occasions of the great job the mining engineers have done persisting against rising costs and increasing salaries without a rise in the price of gold. I think it has been somewhat overlooked that it has been difficult to find additional ore as well. I consider that geologists also should be commended on their action in persisting to search for more orebodies. This goes on in any mining community, but in Kalgoorlie in particular, I believe, over the last few years that it has been more difficult all the time to find additional orebodies and the Companies are calling for higher grades to offset the economic condition. I feel that this paper by Mr. Finucane shows that the geologists have persevered on an idea and discovered that they can find additional orebodies in the calc schist where previously it was thought that these did not occur. This has added many tons to the ore reserves, and although it is not very significant at the moment, the significance will probably improve as more work is done.The whole thing has shown us the importance of economic geology. Mr Finucane has had many years of experience here and he has given us a very able exposition of the economics of ore finding, and there are not many questions that one could pose to him, because most of the information he presented is obviously fact borne out by drilling, underground development and lining up the ore channels. He did briefly touch on ore shoots-the Oroya shoot and several others. It would be very good if we could, and I feel sure...

Jan 1, 1965

By Johnson I. R, Muir M. D

The Dugald River zinc-lead deposit is located 60 km northwest of Cloncurry. It was discovered prior to 1881, and since 1937, has been the subject of several drilling programmcs which have outlined a resource potential of 60 million tonnes grading 10 per cent zinc, 1 per cent lead, and 30 g/t silver.The deposit is a classical example of stratiform zinc lead mineralization in a black shale host. It occurs within a restricted clastic sedimentary basin within the Corella Formation of Carpentarian (Middle Proterozoic) age. Sabkha, lacustrine and fluvial sedimentary environments have been recognized within this basin. Each environment is characterized by suites of evaporite mineral pseudomorphs, after both shortite and gypsum, indicating that both alkaline and hypersaline environments prevailed at different times during basin evolution. The Dugald Slates which host the zinc-·lead mineralization are lacustrine in origin. Thin Mount Isa-type K-rich tuffite beds occur in the Dugald Slates and in the sabkha sequences.The basin as a whole appears not 10 have been marine, and 10 have had strong tectonic controls on its depositional history.The mineral deposit itself is conformable within the Dugald Slates and many primary sedimentary and soft-sediment deformation structures are preserved. It has a strike length of 2 km, average width of 10 m, and a westerly dip of 50-80 . Drilling suggests continuity to 1000 m vertical depth. The predominant sulphides are pyrrhotite, pyrite, sphalerite and galena in graphitic slate and quartz-carbonate ganguc. Anomalous concentrations of barium, manganese, cadmium, mercury and antimony are present in the ore.The deposit crops out over a distance of 2 km as a gossan ranging from 5-15 m in width. There is a striking vegetation anomaly over the gossanous outcrops. The gossan is enriched in lead, silver, antimony, barium, titaniulll, silica and iron, with respect to the primary mineralization. The depth of total oxidation reaches about 20 m.Cieochemical and geophysical test surveys over the deposit give pronounced anomalies.

Jan 1, 1982

This paper discusses support requirements for the proposed monorail system to be used in decline development. The monorail drilling and loading systems are systems that move on the rail (monorail) installed in the roof of the decline and supported by roof bolts, suspension chains and steel supports. However, due to the weight of the components of the two systems, it is imperative that the force in each roof bolt, suspension chain and steel support capable of suspending the weight of the heaviest component is determined. Numerical models that relate the weight of the monorail drilling and loading components to the required strength in the support system have been developed. Using these developed models, numerical values of the forces in each roof bolt, suspension chain and steel support, required to suspend the weight of the heaviest component of the monorail drilling and loading systems are determined.

Dec 6, 2010

By S. Jayson Ripke, Shane Hoff

Cleveland-Cliffs’ Northshore Mining Company operates a magnetic iron ore (taconite) concentrator and pelletizer in Silver Bay, MN. These are two recent cost reduction projects: 1. Rougher Magnetic Separators were upgraded throughout the concentrator; throughput and recovery were simultaneously improved. 2. Green Ball Roll Screens on one agglomeration circuit were upgraded from 3.5-inch to 2.5-inch rolls. Throughput improved by 24% from 62 to 77 LTPH. Green ball size distribution improved as an added benefit.

Jan 1, 2005