Search Documents

By Karl Zipf

In highwall mining, once a sufficient number of web pillars are developed, they can fail catastrophically in a domino-type failure, posing a safety hazard to highwall miners and sterilizing mineable reserves. Three recent case histories of catastrophic web pillar failure in U.S. and Australian mines are documented and analyzed with two design approaches. The conventional design approach uses only a strength criterion, while the postfailure design approach uses both strength and stability criteria to insure an acceptable failure mode should strength failure occur. Catastrophic highwall web pillar failures can cost money through equipment losses, production losses, coal reserve sterilization and lost opportunity costs. Coal recovery may be higher. but the benefits of higher recovery must balance the potential costs of failure. Application of the conventional or postfailure design approach will decrease coal recovery and revenues, but the risk of potentially costly failure is much less.

Jan 1, 1999

By Charles Stone, Hannes Lagger, Dru Desai

The design methodology of the planned Second Avenue Subway Project (SAS) led to development of the initial support design to estimate cost and quantities in the Preliminary Engineering (PE) stage. Careful selection of the cavern design rules that recognized the impact of rock quality, rock cover, excavation geometry, and excavation sequence helped to overcome the design challenges of large, shallow caverns for the initial ground support. In the course of the design verification process prescribed by the design methodology, the design team was continuously reviewing and updating the support quantities. The design procedure includes methods using different approaches of empirical, continuum, and discontinuum analyses, which are currently advanced in the Final Engineering (FE) stage. The paper is a continuation of the RETC 2005 “Trials and Tribulations” and focuses on the procedures that led to the changes in the initial support as a result of the ongoing design development.

Jan 1, 2007

By Michael J. Kelly

IAMGOLD?s Westwood project is the site for the largest, by volume, bored vent raise in North America. When completed, it will be the fifth largest bored worldwide in a single pass. This paper will review the highest capacity raise drill system ever built (Redbore 100); as well as the technical difficulties in a single pass boring a 2,773 ft x 20 ft to 22 ft diameter raise. The difficult ground conditions and associated problems will be reviewed, as well as the solutions to overcome them. Use of the RVDS drilling tool to achieve .04% accuracy (14.5?) and the Geotube® water filtration system will also be covered.

Oct 1, 2010

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania. West Virginia, Kentucky and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought but rather 200 in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Feb 24, 1997

R. W. Raymond, New York, N. Y,:—Since the presentation of my note on this subject at the New York Meeting, Professor Louis has pointed out an error in my statement of his conception of " pitch "—namely, he understands the pitch, in the restricted sense which he proposes, to be the angle of inclination of the axis of an ore-body, measured on the vertical plane drawn through the body; whereas, I represented him as proposing to define " pitch " as the angle of inclination of an oblique body, measured on the plane of the dip, in the direction of the strike. The difference will appear upon consideration of the accompanying isometric projection, Fig. 1, in which ABCD represents the plane of the inclosing ore-deposit (vein or bed), and AC the axis of the oblique ore-shoot. ABE is the angle of the dip, as universally understood; and ACE

Jan 1, 1909

By J. D. Stone

This paper briefly reviews the adequacy of existing management theories and practices and the managerial proficiency or competency in the South African mining industry. The investigation revealed that existing management practices are totally inadequate to enable all employees on all the levels of the mining industry to achieve the results required from them, in all aspects, at all times. As a result, the South African mining industry is gradually losing its long standing reputation as a relative cheap, competitive, and reliable supplier of minerals to the local and global markets. According to some prominent management authors and theorists, an all-inclusive unified management theory does not exist at present. In this paper the authors summarize the main aspects of a newly developed comprehensive, practical, and integrated management method. It is believed that the application of this method would significantly improve the future performance and competitiveness of the South African mining industry

Jan 1, 2010

By José Carlos D?Abreu

The Tecnored process is a new ironmaking technology, developed on a unique approach that combined empirical and theoretical knowledge backed by extensive tests carried out in a dedicated pilot-plant and with close support of universities and research centers. Campaigns in the pilot-plant focused on operate different reactors of different sizes, including a full size slice of the industrial furnace. This approach provided actual conditions to develop the main features of the process such as the internal dimensions, raceway pattern, thermal and gaseous profiles, etc, besides provide reliable data to feed and calibrate a specific mathematical process modeling. This paper presents the first computer model used by the Tecnored technical staff, focusing the behavior of a self reducing agglomerate in the upper shaft of the furnace (zone of solid state reduction). Some results of this model are given and discussed.

Jan 1, 2006

By Martin H. Rogoff

This publication combines a critical review of the literature on the microbiology of coal with an introduction to those areas of microbiology related to studies of coal as a biological material. The attack on coal by microorganisms as yet remains doubtful. Only the low-rank coals contain an indigenous microbial flora, and even these organisms are not peculiar to coal, but are common soil and water forms. No experimental data have as yet been presented, either in the literature or in the present work, which unequivocally demonstrate the oxidation of coal by microorganisms. Reasons for the resistance of coal to such attack, including insolubility, physicochemical structure, steric hindrance of enzyme action, and the presence of antibiotic materials in coal are discussed. Microorganisms do attack large aromatic molecules and the mode of oxidation of aromatic ring systems by bacteria is presented. Well-defined pathways are known for the oxidation of polycyclic compounds with one to three rings, and these paths with their key intermediates are described and related to the possible oxidation of coal.

Jan 1, 1962

By Angela Selau Marques

A ferramenta CAE possibilita a avaliação do processo de forjamento virtualmente para otimização da produção industrial reduzindo o custo final do produto através do mínimo uso de matéria prima, juntamente com a previsão das variáveis que ocorrem durante a conformação do material no processo. Os procedimentos necessários para o forjamento de uma peça com geometria de média complexidade forjada em alumínio é apresentada. O objetivo deste trabalho é analisar experimentalmente o forjamento desta e compara-la com a simulação computacional.

Aug 8, 2018

By F. W. Bowdish

A theoretical and experimental laboratory study has shown that the rate of breaking of oversized particles in a ball mill is proportional to 1) the concentration of such particles, and 2) the area of the balls, provided that the balls are larger than a certain size relative to the particles. If all undersized material were removed as formed, the rate of breaking would be almost independent of the quantity in the mill. Rate equations are given which are similar to those for zero, first, and second order reactions. Deviations of small balls from the equation for a second order phenomena are quantified by a factor called "nipping efficiency." Some data are correlated by a dimension-less equation, which is used to estimate nipping efficiencies from data not in the correlation. The investigation described here was undertaken after a literature survey revealed that little was known concerning the mechanism of breaking of particles within a ball mill and the effect of this mechanism upon grinding rates. One paper, by Roberts1 , offered a theory concerning the mechanism of breaking, and a rate equation for the breaking of particles larger than some size to particles smaller than that size. That paper provided the starting point for a theoretical and experimental investigation of grinding under carefully controlled conditions. THEORETICAL CONSIDERATIONS In his paper on the probability theory of ball mill grinding, Roberts theorized that "... a given expenditure of power leads either to a certain number of point to point blows per bp-hr or to a certain distance of line contact per hp-hr ..." He assumed that the balls touch each other during each blow or during moving contact. Then he said that a volume of pulp, dependent upon the size being considered, would be covered per minute within which all oversized particles would be crushed to particles smaller than that size. Naturally, the higher the concentration of oversized particles in the pulp, the higher the rate of which they would be broken. From this reasoning Roberts obtained the differential equation -dC/dt = k hp/ton C (1) where k is a constant for any size of particle, density of particle, and moisture content of pulp. C is the percentage of oversize in the material to be ground, t is the time, and hp/ton is the power input per ton of material in the mill. He then integrated the equation to log Co/Ct = k/2.3 hp/ton t , where Co and Ct are the percentage of oversize at time zero and t respectively. By always using the same quantity of material in a mill and assuming that it required constant power to run the mill, he was able to combine the horsepower per ton factor with the other constants to give an equation for a first order rate.

Jan 1, 1961

By K. Kohli

A case study involving a historic structure undermined by longwall mining is presented in this paper. The location of this study is in South Western-Pennsylvania; USA. The structure is 150-years old and subsided 4.5 feet. This paper discusses the mitigation measures taken to reduce the subsidence damage and its effectiveness.

Jan 1, 2002

By R. Zivojinovic, S. Vujic

The structural age of the capital mining machinery, representing a part of the system of the Electric Power Industry of Serbia, has been dictated by the initiation and development of open pit coal mines. For example, the oldest bucket wheel excavators were installed some thirty-four years ago, and the average life of the relevant machinery exceeds twenty-two years. Operation of both capital equipment and machinery has direct effects on economic and business activities of open pit mines, and consequently forced us to make a decision and study thoroughly the problem of establishing the optimum exploitation life of capital mining equipment at the open pit coal mines of the Electric Power Industry of Serbia. The aim of this paper is to define and discuss the relative problems as well as to find out the possible solutions and establish the methodology for estimating the optimum exploitation life of machinery. The study was successfully carried out by a team of scientists engaged from and coordinated by the Department of Computer Science of the Faculty of Mining and Geology, University of Belgrade. This paper presents the key observations covering the subject problem. Keywords: Mining, Opencast exploitation, Coal, Optimization, Exploitation life, Capital machinery, Electric power industry, Dynamic programming.

Jan 1, 2003

By Pedro Lilienfeld

This report describes a program to develop, design, fabricate and subject to environmental testing three prototype collection-sensing devices of an eventual mining-machine mounted automated monitor for the measurement of the respirable fraction of coal mine dust to determine both short-term as well as average mass concentrations over typical 8-hour shifts. The design of this instrument is based on collection by filtration and mass sensing by beta-radiation attenuation. The emphasis of this development program was to evolve a rugged, stable and reliable collection-detection head compatible with the environment to which An eventual monitor will be subjected. Laboratory testing of this prototype instrument was performed over a representative range of temperature, humidity, dust concentration and composition, shock and vibration. The results of this testing program indicated that the operation of the prototype version His compatible with these environmental conditions and that further development of this configuration into a field operational device is justified.

Jan 1, 1977

By Berger

A detailed description is given of radio apparatus for controlling a coincidence outfit for relative gravity measurements. This is probably of little interest, since many types of apparatus could be used. The general method employed is the interesting thing about this paper. As long ago as 1883 von Sterneck made a proposal to control two coincidence boxes with the, seine, clock, and many persons have suggested the use of radio for this purpose. In accomplishing this it would appear to the reviewer that this method is probably inferior to that used by the Marland Oil Co., but Berger and Brückner must be given the credit for important advances in the coincidence method. In their apparatus a clock at a central station actuates a relay, which operates a short-wave transmitter (40 m.). At the receiving station the amplification is accomplished at low frequencies... The signal operates a relay which moves a slitted screen in a coincidence apparatus. This screen has been improved considerably, to decrease the mean error in observing a coincidence. As usual, a telescope is used to observe the flashes of light. It has a scale in its focal plane and positions of successive flashes are easily read off and recorded by a second observer. This makes possible' a: higher accuracy in determining the exact instant at which coincidence would have occurred at the zero point on this scale. This method obviously depends on the constance of the mechanical and electrical lag inn both sending and receiving apparatus, and may be adversely criticized from this standpoint. -- A. E. Ruark.

Jan 1, 1929

By Michael A. Staiano

The objective of this study was to determine the magnitude and sources of environmental noise from mining operations near populated areas, to de-scribe monitoring techniques, and to identify applicable existing noise abatement techniques. To this end, noise surveys of a representative sample of mines and quarries were conducted. Noise levels at site boundaries and near specific equipment and ensembles of equipment were measured. Noise exposures in terms of annual day-night sound level were calculated for the boundary noise measurement locations. In addition, the relative sound level contributions were estimated for the mining equipment noise sources affecting the boundary locations. Noise abatement methods falling into three categories were analyzed: equipment practices, operational/administrative practices, and equipment quieting. Selected applications of noise abatement methods were evaluated in hypothetical situations with emphasis upon machinery selection and use. Procedures for measuring noise around mining operations were provided.

Jan 1, 1981

By Fred V. Carrillo

Of the total quantity of secondary copper and zinc that became obsolete in the United States from 19b1 through 1970, more than 11 million tons of copper and 10 million tons of zinc were not recovered. These estimates are based on a study of the flow and recovery of old copper and zinc scrap by consumption end-use. This report describes (1) where copper and zinc are being used; (2) when they become obsolete and available as secondary metal; (3) how they are being collected for recycling; and (4) how much might be recovered from scrap that presently is not being recycled.

Jan 1, 1974

By G. L. Smith

Central to the success of any mining company is the ability to manage capital investment effectively so as to ensure acceptable stakeholder returns within an overall strategic context. Critical to this process is the effective selection and implementation of a strategically aligned project portfolio that enables optimal resource exploitation while operating within mandated bounds and identified constraints. Consideration is given to the strategic long-term planning process, an investment prioritization methodology and specific tools and techniques based on the discounted cash flow philosophy.

Jan 1, 2007

By D. Harry Chambers

The Bureau of Mines, through a memorandum of agreement with the Department of Defense, conducted research to recover silver from aircraft scrap. Silver was recovered by an electrolytic method from stainless steel honeycomb sections separated from the aircraft. These sections had been constructed by sandwiching a stainless steel honeycomb core between stainless steel sheets and then brazing the assembly with a silver alloy. Over 300 pounds of silver was used in the B-58 bomber, concentrated in certain honeycomb sections of the aircraft. Following shredding of the aircraft parts, an average of 95 percent (ranging 67 to 100 percent) of the silver was recovered in a single electro-refining step. After the electrorefined product was magnetically cleaned, purity of the recovered silver was greater than 99.3 percent.

Jan 1, 1980

By Sam S. Taylor

"INTRODUCTION This report deals with a comparatively simple application of some of the engineering principles involved in the evaluation, installation, and operation of air- or gas-injection projects and well-clean-out and repair methods to increase the producing rates of oil wells in partly depleted pools during the war. The methods suggested for developing gas-injection projects take into consideration that in general no new wells will be drilled because of wartime restrictions of equipment and manpower and that only existing wells and second-hand machinery will be used. Because air will be employed as the injection medium in secondary-recovery operations where natural gas is scarce and expensive, the disadvantages and hazards accompanying, its use are discussed. Engineering techniques recognized as best modern practice are discussed in relation to the effect of simple air-injection development of properties on postwar operations and Probable ultimate recovery of oil. The report is an introduction to where, when, why, and how an air-injection project should be installed and operated; it is not intended to be an engineering manual for technical guidance in the selection, development, and operation of simulative methods of oil recovery.The report is intended mainly for these thousands of operators in the Appalachian region owning a few wells prodding small quantities or oil daily. Many such operators are anxious to increase their production rates by simulative means and to rehabilitate their wells so that they will produce more oil to help win the war but, in general, are unfamiliar with secondary-recovery operations and cannot afford to hire technical assistance."

Sep 1, 1944

By L. W. Berger, and R. I. Jaffee, D. N. Williams

The effects of hydrogen on the properties of binary Ti-A1 alloys containing 2.5, 5, and 7 pct aluminum and ternary alloys of the same compositions with added interstitial elements oxygen, nihrogen, and carbon were stzdied. Aluminum increases the apparent hydrogen solubility of the a-phase, resulting in a marked increase in resistance to impact embrittlement. In the Ti-5Al and Ti-7Al alloys, for example, the addition of 180 and 305 ppm hydrogen, respectively, did not cause embrittlement, while unalloyed titanium was embrittled by as little as 75 ppm. The role of aluminum in increasing hydrogen solubility of the a-phase probably accounts for the excellent hydrogen tolerance of a-ß alloys containing considerable amounts of aluminum. There is some evidence that aluminum retards the rate of hydride precipitation. If so, these alloys may be susceptible to slow-strain embrittlement. UNALLOYED a-titanium is extremely sensitive to small amounts of added hydrogen in that there is a marked decrease in notch properties. For example, as little as 100 ppm hydrogen is sufficient to lower the room-temperature notch-impact strength from over 100 to less than 20 in.-lb.' This loss of impact Strength has been associated with the Presence of hydride phase in the microstructure. Hydrogen in the amounts encountered in commercial practice

Jan 1, 1959