Search Documents

By A. Cichowicz

The objective of this work is to quantify the effect of the rock mass surrounding a stope or a tunnel on the seismic signal so that the rockburst damage on the excavation can be derived. It has been shown that the transfer function of rock mass surrounding an excavation can be modelled using a damped oscillator. The method of estimating the transfer function is extended in this paper. The parameters of a damped oscillator are estimated using inversion techniques and the transfer function is modelled as a time-varying system. The technique is tested on data acquired at three different sites in two deep gold mines. Employment of a modal model of the transfer function was suitable in two cases. Application of this technique is essential to track the time variation of the natural frequency during ground motion caused by a seismic event.

Jan 1, 1999

By P. Leo

The Al-Zn-Mg alloys (e.g. 7004, 7020) are employed for land transport and architectural applications whereas the Al-Zn-Mg-Cu alloys (e.g. 7075, 7050) provide the high strength aircraft alloys. The Cu gives rise to suitably sized and distributed precipitation but causes high quench sensitivity. Their hot work processing also has marked differences; the Cu-free alloys have good extrudability whereas the Cu-bearing alloys have low extrudability and are difficult in rolling as well. The behaviors of the two classes are described in terms of flow stresses and ductility over 300 - 500°C, along with constitutive contrasts. The ductility of the alloys with Cu is much reduced above 400°C by precipitation of a phase at the grain boundaries that can be avoided by suitable heating schedules. The high strength alloys are subject to de-lamination corrosion of sheared edges due to severely pancaked grains; this can be alleviated by holding between passes, in mid-rolling schedule. In torsion tests at 10-1 to 10 s-1/ 250 - 500°C, the stresses (ductilities) at 300°C/ 1s-1 and activation energy Q for 7004 were 118 MPa (2) and 262 kJ/mol. The 7075 was tested after several pretreatments: completely over-aged (softened): 107 MPa (5), Q=150 kJ/mol; whereas, solution and quick cooling to testing caused extraordinarily high peaks related to dynamic precipitation resulting in 160 MPa (1.2), Q=300 kJ/mol.

Jan 1, 2011

By Y. Zhoa

The surface morphology of materials is of fundamental importance to many surface related applications, such as wetting, friction, reflection, drag, and adhesion. Various approaches for micro/nano patterning atop polymer surfaces have been proposed in recent years. However, a cost effective technique is still highly in demand. In this paper, we demonstrate a novel but rather simple and generic approach for surface micro/nano patterning using shape memory polymers (SMPs). Different types of novel patterns are realized and their 3-D surface features are quantitatively analyzed by a PLµ Confocal imaging profiler.

Jan 1, 2010

By S. G. Hardcastle, C. K. Kocsis

Ventilation is an expensive prerequisite for underground mining. Current mining trends, including increasing depth and mechanization and more stringent health regulations would generally dictate that more air volume is required in order to provide good working conditions underground. However, any increase in the mine’s intake airflow can produce a disproportionate increase in power consumption and hence operating costs due to the cubic relationship between the sup-plied air power and the airflow (Power a Flow3). Furthermore, forecasts of significant increase in energy prices and new commitments with regard to reductions of greenhouse gas(GHG) emissions, determined the mining industry to look into developing new concepts, design tools and incorporate the latest mining technologies in order to lower capital and operating costs while meeting commitments regarding GHG emissions. The advances in computing power and modelling software now make it possible to design, model and schedule a mine from opening to closure. A developing trend is to design and plan the mine by means of orebody modelling software, followed by using discrete-event simulation techniques to predict production rates and evaluate various operating scenarios throughout the life of the mine. The authors are currently evaluating how such process simulators could be adapted in order to forecast the need for materials or a specific resource, and one of these would be the mine’s “life-cycle” airflow demand as a function of scheduled production rates and mine operating characteristics. Further to this, based upon the mine’s life-cycle airflow demand schedule, the ventilation system could then be designed using a mine ventilation simulator. This new design approach would integrate in parallel the development of the ventilation system with the current mining conditions, therefore, heading towards “develop-as-you-go” as opposed to developing the system for final requirements with high upfront costs. This new ventilation system design criteria would also incorporate the use of the “ventilation-on-demand” technology, which will further lower development and production costs and implicitly, the mines’ GHG emissions.

Jan 1, 2004

Objective To develop safety training tools for mine health and safety trainers that fill gaps in currently available materials and help capture the wisdom and knowledge of “expert miners.” Background NIOSH began a series of stakeholder meetings in 1998 to determine what research was needed to improve miner health and safety. One of the more common concerns among stakeholders was a critical lack of appropriate training materials applicable to metal/nonmetal mining. Participants provided many insights into what effective training materials should include and how materials could best reach both new and experienced miners. The most important factors were that any materials be realistic and interesting and that some way must be found to capture the wisdom of expert miners before they retired. Approach NIOSH researchers chose videos as the best means of achieving these training goals. Over the past 3 years, NIOSH has produced three training videos that present information on safe work practices in underground mines: handling explosives, recognizing roof hazards and using proper scaling techniques, and installing ground supports. The last two videos, “Rock Falls—Preventing Rock Fall Injuries in Underground Mines” and “Miner Mike Saves the Day—or—Ground Support…It’s Important,” have won Alice Hamilton awards, NIOSH’s highest recognition of Excellence in Occupational Safety and Health, in the Educational Materials category. Two new videos are now being released. Both of these videos were shot completely in operating underground hard-rock mines and used expert miners to tell the story. Hazards In Motion The first, “Hazards in Motion,” deals with the dangers of working around mobile equipment in an underground mine. Ben, a new trainee, refuses to pay attention in his 40-hour New Miner Training class, and when the class takes its first trip underground, he wanders off and finds himself in many dangerous situations. He encounters many experienced miners who both chew him out for his unsafe attitude and give him advice and information on how to survive around mobile equipment. Many common pieces of equipment are shown, including haulage trucks, LHD=s, tracks and trains, slushers, skips and hoists, and air doors. The dangers of ignoring signals and of horseplay are also included. After nearly losing his life numerous times, Ben learns his lesson with the help of the Safety Angel, an experienced miner who looks suspiciously like his safety trainer. Ben’s Safety Angel saves his life repeatedly, teaches him how to work safely around these common conveyances, and introduces him to experts who have specific safety tips. Ben learns the error of his ways and vows to be the safest miner in the mine. “Hazards in Motion” is approximately 30 minutes long. Hidden Scars The second video is the first in the NIOSH “Expert Miner” series. “Hidden Scars” is a narrative interview with Don Capparelli, a miner and supervisor at the Sunshine Mine in north Idaho. This video captures the story of a fatal rock burst in May 1994, when Don was seriously injured and his long-time partner, Jimmy Findley, was killed. “Hidden Scars” is a very powerful story. Don Capparelli shares the physical and emotional pain he lives with daily as he relates the events leading up to the rock burst that took the life of his best friend and partner. This video is an excellent reminder of the human cost of uncontrolled accidents and the hidden scars that survivors must deal with for the rest of their lives. It runs approximately 25 minutes.

Jun 1, 2001

By H. J. McQueen

Large-scale industrial production of pipe began with longitudinal hot pressure welding of wrought iron by passage of skelp (narrow strip with beveled edges) through a die or bell that curled it about a longitudinal axis until the edges were forced together. Such small to medium tubes could be reduced by rolling or drawing; with threaded connections, they were excellent for distribution of clean water and of illuminating gas for street, home and industrial lighting. Although steel lacks the fluxing slag for pressure welding it has hot strength similar to iron; hot-pressure bell welding was advantageously transferred to steel in long coiled strip with 50% higher cold strength. For pipe without weld-line defects, hot cupping followed by Pilger mill rolling produced tubing that revolutionized bicycle quality and high-pressure service for boilers and chemical processing. Mannesman hot rotary piercing produced long thick walled tube that permitted reduction or expansion by rolling to provide pipe sections up to 60 cm diameter and 12 m long. During 1910 - 1940, oil and gas pipeline technologies, notably welding evolved markedly as they proliferated in the United States, in response to far-flung petroleum fields, expanding industry consumption and the automobile revolution. In the Second World War combat pipelines were laid rapidly, such as: the Canol line through the Yukon to Alaska, and fuel supply lines across the channel and through liberated France. Perfection of welding techniques for both longitudinal and spiral weld large diameter pipe in combination with controlled-rolling of micro-alloyed steels made possible reliable Arctic pipelines. The development of pipe production and utilization in Canada is recounted. The fabrication techniques and metallurgical controls are explained.

Jan 1, 2005

Discrete Element Method - Computational Fluid Dynamics Modelling of Flow Behaviour in a Stirred Mill - Effect of Operation Conditions

Sep 13, 2010

By J. Ritchey

This report describes the engineering feasibility and economic advantages of using a mobile bridge-type cross-pit belt conveyor system in conjunction with a large dragline to excavate and transport spoils in a typical Western surface coal mine. The studies show that such a system could be built to survive operational and climatic mining conditions, and that its implementation would offer a reduction in both acquisition and operating costs versus conventional mining units of comparable rapacity. Reclamation costs can also be significantly reduced, and the total reclamation process accelerated, making the cross-pit conveyor system attractive to mine Owners and environmentalists alike.

Jan 1, 1976

By P. den Hoed, R. I. Rambiyana

"Four sulphide minerals - pyrite (FeS2), pyrrhotite (Fe1-xS), pentlandite ([Ni,Fe]9S8), and chalcopyrite (CuFeS2) - contain the base metals and most of the iron in concentrates of platinum group metals (PGMs). In the pyrometallurgical processing of PGM concentrates these sulphides form a matte during smelting, and iron and sulphur are removed from the matte during the converting process. This paper discusses the roasting of Merensky concentrate in air before smelting, with the purpose of reducing the matte load to the converter.Roasting tests were conducted in a bench-scale rotary kiln at temperatures from 350°C to 700°C. The concentrate tested contained 17.4% sulphur and consisted of 23% pyrrhotite, 16% pentlandite, 11% chalcopyrite, and 2% pyrite. The particles were fine (d50 = 22 µm), and all the sulphide particles were liberated. Roasting in air at 550°C and 650°C for 20 minutes removed respectively 60% and 70% of the sulphur. The iron in the sulphides was oxidized to Fe3O4 (magnetite) at temperatures below 500°C and to Fe2O3 (haematite) at temperatures above 550°C. At 700°C the bed sintered and copper oxides formed. At temperatures below 450°C oxidation was incomplete: pyrrhotite remained and only 30% of the sulphur was removed. Smelting tests were conducted to assess matte fall and the deportment of copper and nickel to matte. It was evident that roasting resulted in lower matte falls (a drop of approximately 60%) compared with matte falls from unroasted concentrate. The iron and sulphur levels in the matte were reduced to below 3.5% and 22% respectively.This paper also briefly describes the mechanisms by which pyrrhotite, chalcopyrite, and pentlandite are oxidized during roasting. For chalcopyrite, the mechanism proceeds through an intermediate solid solution phase, which extends from Cu1.02Fe1.04S2 to Cu2.04Fe0.72S2 to a copper-rich solid solution of bornite (Cu4Fe1.4S4-Cu2S). The oxidation of pentlandite proceeds through a monosulphide solid solution (Ni0.39Fe0.53S-Ni0.74Fe0.15S) to a solid solution of heazlewoodite ([Ni,Fe]3}xS2). These mechanisms are explored in relation to chemical thermodynamics and microstructures."

Jan 1, 2015

By Seal. Thom

Large heap leach operations around the world contain significant under-leached metal values that present recovery challenges to operators. The first challenge is to find the location of the highest inventory. High resolution resistivity ? has proven sensitive enough to detect such zones in the interior of heap leach pads to target treatment or re-leaching. Newmont Mining Corp. has adapted the high pressure fracturing technology, used in oil wells to stimulate select zones in heap leach pads to add reagents in 3-D for re-leaching, changing zonal chemistry for improved recovery and heap closure. High Resolution Resistivity ? is able to subsequently monitor injected solution flow and determine directional permeability during Hydro-Jex stimulation. The combination of these technologies has shown strong economic success, for selecting targets in the heaps and monitoring solution application. These technologies are now available to the mining industry for adoption.

Jan 1, 2008

By M. Drozd, M. Somppi, Z. Yamak

"Granular activated carbon is widely used in the gold mining industry for gold extraction from aurocyanide-containing slurry. The extraction process can employ carbon as part of the gold recovery operation for various circuit designs including carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) circuits. However, various qualities of activated carbon exist and the durability of the material can change significantly from source to source. Handling this expensive reagent can pose challenges when fine carbon losses occur in the CIP, CIC, and CIL circuits. Additionally, any gold that is adsorbed to these carbon fines can also be lost by various mechanisms including carbon attrition and fracturing, inefficient coarse-fine separation, and poor carbon fines capture. With the above in mind, a series of tests were conducted to investigate standardizing simple laboratory methods for testing carbon quality. A standard procedure beyond or enhancing ASTM methods can serve as additional starting points for evaluating carbon specific to the gold industry. The investigation focused on size distribution, flatness, wet attrition resistance, surface area, gold kinetics, and gold loading. The final results provided information to generate an equation for ranking carbon samples to plant performance.IntroductionActivated carbon for use in gold extraction is amongst the most commonly found processes in modern gold-milling plants. Although gold losses are inevitable in the milling process, operators often focus on the importance of maximizing gold recovery. One focus area that is important in gold recovery is optimizing the use of activated carbon and examining potential changes to realize improved economics for carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes."

Jan 1, 2017

By N. W. Johnson

"Two analysis tools which have been applied to problems in industrial flotation processes are the application of kinetics and detailed mineralogical or liberation data, both on a size-by-size basis. This paper describes practical examples of the application of kineticsto examination of the entrainment recovery mechanism, the retardation of valuable minerals at the commencement of flotation sections and the resolution of problems related to valuable species with reduced rate constants at the end of sections. Examples of the usefulness of size-by-size liberation data for monthly composite samples of products from a concentrator are also described.IntroductionMuch of the published industrial flotation data on the behaviour of minerals in various size fractions have been obtained from specially conducted surveys with a duration of several hours. Such data are very valuable and provide a record of the behaviour of the entire flotation plant or sections during the interval of the survey. Some examples from the literature can be cited Cameron et al. (1971), Lynch et al. (1981), Frew (1982). Less attention has been given to the value of complementary sized data derived from compositing shift or daily inventory samples over an interval of one or several weeks with repetition of the procedure at the completion of each interval. Mineralogical point count data of the size fractions of such samples and data interpretation are rare in the literature.Kinetic data on the behaviour of valuable and gangue minerals in various size fractions have been reported often for flotation banks. In the experience 0 f the writer, there has been a tendency among operating metallurgists to ascribe problems in the flotation process to rate constant values for gangue minerals which were believed to be unsatisfactorily high. Less attention has been paid to the value for the rate constant for the valuable mineral over the length of a particular bank.Examples of the types of data which were mentioned previously have been obtained from the lead-zinc concentrator at Mount Isa Mines Limited. The various types of data have been collected to evaluate their worth in order to provide relevant information for both research and operational aspects of the plant."

Jan 1, 1987

By Jim Nickerson, James McCleish, Tom Abkemeier, Nicholas Willig

The purpose of this project is to convey sanitary sewage from an existing pump station to a new waste water treatment plant. This paper will discuss the design and construction aspects of the project. The scope includes construction of three main shafts ranging from 34 to 100 feet in diameter at depths of 200 to 230 feet and 21,000feet of tunnel. Shaft construction consisted of slurry wall excavations keyed into claystone and limestone at depths ranging from 114 to 130 feet, followed by rock excavation utilizing drill and blast methods. The tunnel is being excavated in the Warsaw and Salem shale and limestone formations utilizing a 12'-6" diameter Wirth hard rock TBM.

Jan 1, 2005

By James W. Cassie

The Snap Lake Diamond Project is located approximately 220 km northeast of Yellowknife, NT, Canada at an approximate latitude of 63?35?. The project location is within the zone of continuous permafrost; measured ground temperatures are about ?2?C at 10 to 20 m depth below surface. The site is located on a peninsula jutting into Snap Lake. The site is generally barren of vegetation, except for some isolated areas with low trees located in topographic lows and near the shoreline of Snap Lake. As part of phased evaluation process with regards to the mining project, an Advanced Exploration Program was undertaken in 2000 and 2001. This program included the underground extraction of a bulk sample of kimberlite, which was processed on site. A Processed Kimberlite Containment (PKC) area was required as part of this program. The area chosen as the PKC facility was a small inland lake, called Inland Lake #1, on the peninsula. Construction of the PKC area required the construction of two dams, one on either end of the lake. At the south end of the lake, Dam 1 was constructed partially on a talik and partially on continuous permafrost. Dam 2 was constructed entirely on permafrost. The effects of the remote location, selection of suitable construction materials and permafrost conditions on the designs of the dams are discussed. A description of the design elements and construction schedule are provided. A review of the performance of these two dams, in terms of settlement, deformations, pore pressures and thermal regime, over the last several years is provided.

May 1, 2003

By U. Storck

"Shaft sinking for exploitation of the deep potash beds in Saskatchewan involved great difficulties from the very first because of the need to exclude from the shaft the high-pressure water encountered in the overburden. Control of the troublesome Blairmore quicksands was achieved relatively quickly by use of the freezing method and by lining with cast iron tubbing. The unsolved problem remained, however, of sealing the water-bearing Devonian where the formations had extremely low permeability and were thus hard to grout. Long experience in German potash mines had shown that the permanency of the whole mine would be seriously endangered if large amounts of unsaturated salt water were allowed to flow in from the shaft wall and merely removed by pumping. The prevention of water movement and the resulting dissolution of salt in the overburden were known to be most important. In the Alwinsal shaft, water flow from the Devonian has been prevented by the use of a steel and concrete sandwich lining similar in principle to a kind of lining introduced a few years earlier, and for another reason, in German coal shafts. As its installation is neither more expensive nor more time consuming than that of cast iron tubbing lining, this same lining was also chosen as protection against the Blairmore quicksands. The great advantage of the steel lining, in addition to its relatively high strength, is the fact that it is possible to make the joints of the individual segments absolutely and permanently water-tight by means of tested welds. The virtual dryness of the Alwinsal shaft will also result in lower costs because significant corrosion of all its steel installations, including skips, cage and ropes, will be prevented."

Jan 1, 1968

By Luciano Gianizeli Rodrigues

Este trabalho estuda a obtenção da fase S livre de precipitados, a partir da nitretação a plasma de pós de aço inoxidável austenítico 316, e analisa a variação do parâmetro de rede (aS) em função das diferentes condições de tempo e temperatura de tratamento. Os pós com granulometria entre 38 e 54 ?m foram nitretados em reator a plasma pulsado DC, sob atmosferas de 80%N2 e 20%H2, pressões de 400 Pa, por tempos de 1 a 9 h, e temperaturas de 420, 450 e 470ºC. Os resultados mostram que para a temperatura de 420ºC o parâmetro de rede (aS) aumenta continuamente com o tempo de tratamento, atingindo a máxima expansão (8,5%). Com o aumento da temperatura e do tempo de tratamento, verificou-se um recuo em aS associado à perda de nitrogênio e conseqüente formação de nitretos. É possível obter na temperatura 420ºC após 9 h cerca de 37% de fase S livre de precipitados, o que mostra a necessidade de realização de experimentos adicionais ou do desenvolvimento de métodos de separação das partículas nitretadas das não nitretadas.

Aug 8, 2018

By B S. Utting, W J. Cowie

The alluvial gold industry of New Zealand is based on the placer deposits in Otago and on the West Coast. Production from these since discovery in the 1850s has been an estimated 480 t (15 Moz) of gold. Annual output has expanded continuously since 1980 and is expected to be over 2 t of gold for 1989. Following a historical review, the characteristics of typical operations, which use hydraulic excavators and mobile trommel units are discussed. Descriptions are then given of alluvial activities in Otago and on the West Coast.

Jan 1, 1990

By Brock Wallis, Steve Davidow

The following text will present the concept of rock socketed drilled shafts used to support electrical substation structures, and discuss the cost and schedule risks that traditional design responses to unforeseen shallow rock can pose to a project. Design considerations will be detailed, including rock characterization, shear strength of drilled shafts, and modeling lateral resistance of the shaft and surrounding rock. The specific case of drilled shafts installed for heavily loaded structures at the Moxie Freedom Substation will provide an example of how close collaboration between the engineer and contractor to refine designs based on site-specific feedback can provide tangible benefits to the project. In this example, value engineered designs resulted in an approximate 40% reduction in shaft/concrete volume and a 60% reduction in total rock socket depth. PROJECT OVERVIEW The Moxie Freedom Project included the construction of a new 500 kV switchyard in Berwick, Pennsylvania. The foundation contractor was selected to install both small and large diameter drilled shaft foundations to support the structures within the switchyard. The small diameter shafts were utilized to support transformers, switches, bus supports and a static mast, while the large diameter shafts were used to support one 180-foot monopole and six H-Frame structures. CHALLENGES: ROCK SOCKETED DRILLED SHAFTS Available geotechnical data at the time of bid included limited borings and seismic refraction. The borings were not located at every structure, and the contractor and design engineer were left to interpret desktop studies and geophysics to determine the probable site-specific conditions at each foundation. The data suggested substantial variability in the quality and depth to bedrock across the project area, indicating significant risk of deep embedment into bedrock at all seven large diameter shaft locations. Rock socketed drilled shafts pose unique challenges for both designers and contractors, and the topic has become a focus of national foundation organizations. Traditional design models result in deeper and/or larger diameter shafts where rock is encountered. In the case where site-specific geotechnical conditions are not clearly understood and rock is encountered at shallow depths, this can lead to significant additional rock drilling, impacting overall project cost and schedule. Rock drilling can result in more than ten times the cost of soil drilling and can easily take in excess of ten times longer to excavate.

Jan 1, 2018

JESSE L. JONES,* Pittsburgh, Pa. (written discussion?).-As the die-casting process is so very different in character from the process of making sand molds, it is often considered that entirely different methods of pouring, gating, venting, etc. should be used. There is really, however, no essential difference in the making of (lie castings and sand castings, and similar methods should be used in each process. In the matter of gating, the metal should be introduced at a central point, as nearly as possible, so that it will have an equal distance to flow from the point of entrance to the most distant points of the mold. This will cause a uniform rate of congealing of the casting and prevent streaks and cold shuts. The venting should be done in such a way that a free exit of the air in the molds can occur. It should be less difficult to take care of the venting of a die-casting mold than to vent an ordinary sand mold. In the case of a sand mold, the venting is left, to a considerable extent, to the judgment of the molder, and it is possible that no two molds will be vented in a similar manner. Further than this, after a vent has been made in a sand mold, it may become clogged by the sand and for this reason be inefficient. There is also quite a variation in the pressure of the metal entering a sand mold, due to varying heights of the pouring gate. In a die-casting mold these factors can be controlled more closely. The vents should be so disposed that the air in the mold compressed by the entrance of the metal may be able to leave the mold at a uniform rate and by exits located symmetrically. These exits are made quite small on molds at first, as they can he easily enlarged if necessary, and they are tapered so that a free flow is guaranteed without danger of the metal spurting out from the die. Uniformity of pressure of the metal as it enters the mold is very important and, as the pressure is mechanically applied, its control is not difficult. It is true that a sand mold has much less of a chilling effect on the metal poured into it than has the die-casting mold, but, outside of this point, there is a great similarity between the die-casting process and the process of making castings in sand folds. It is suggested that much would be gained by regarding these two processes as not essentially different.

Jan 4, 1919

By Pullen G, Rose M

Continuing Professional Development (CPD) is not just a catch-cry. It is an essential component of every-day life in many professions, including accountancy, law and public administration. Without realising it, many other professions are undertaking CPD activities in an un-structured way, including mining, metallurgy and geology. Examples include Annual and technical conferences of The Institute, Branch-level technical meetings and in-company training and development programmes and technical exchanges. Whilst approaches to date have undoubtedly helped keep the Australian mining industry at the forefront of mining technology, one cannot presume that technological development will stand still. To meet this challenge, human resource development must keep pace, not only to optimize utilization of technological developments, but more importantly to develop firm bases from which new products, processes and technologies can be developed within Australia.

Jan 1, 1989