Search Documents

By G. G. Krishna Murthy

Several experiments were carried out to simulate the bath smelting reactions where iron oxide particles were dropped on to an iron-carbon bath containing molten CaO-SiO2-Al2O3 slag layer on its surface. The composition of the slags used in the experiments was %CaO:46.1; %SiO2:41.7; and %A1203:12.2. Experiments were con¬ducted with carbon saturated iron melts contained in either a pure graphite crucible whose walls were covered with a pure alumina tube, or a pure flat bottom alumina crucible, at 1723-1823 K. Degree of reduction of a pure iron oxide particle was linear with time in the initial stages (up to about 20% oxygen of the original pellet was reduced). The rate of reduction of smaller oxide pellets was smaller than that of a bigger pellet - the time for complete reduction of a 5.6 g wustite pellet was smaller than that for a 1.2 g wustite pellet. It was also established that the interaction rates obtained by adding a molten pure oxide particle of given weight to the system were lower than that determined by using a solid oxide particle of same weight. The overall rates of reduction decreased with decreasing the bath temperature. The experimentally determined rates of reduction based on the time for 70% reduction were influenced substantially by addition of slag up to about 50 g on to a bath of 78.8 mm in diameter, and remained constant when slag present on the bath surface was between 50 g and 200 g.

Jan 1, 1993

By Alessandro Navarra, Joël P. T. Kapusta

"The converting cost modeling software introduced by Ng et al. in 2005 [1] has been extended to consider the reprocessing of reverts and copper scrap. The original model evaluated the operational costs of a Peirce-Smith converter; algebraic relationships had been implemented with arrays (to represent matrices, vectors and scalar ratios). The new software brings flexibility to the underlying thermochemical balances, by using linked-lists instead of arrays. It is now possible to consider the blending of several feeds, including reverts and scrap.The software computes the length of the converting cycle from the Fe and S content of the charge together with the blowing rate; the times required for other operations (charging, skimming and idle time) are also accounted for. The costs of consumables such as flux, fuel, oxygen or compressed air are all evaluated. Downtime, labor, and materials for converter lining repairs are also considered. The software is easily extended to examine the costs of alternative operating strategies or injection technologies such as sonic single pipe injection and sonic shrouded injection. The potential cost benefits of alternative operating procedures and technologies are discussed through example calculations."

Jan 1, 2009

By Ramana. G. Reddy, Haoxing Yang

The electrodeposition of zinc from zinc oxide using urea and choline chloride mixture in a molar ratio 2:1 is investigated in different experimental variables, namely, the concentration of added [BMIM]HSO4, temperature, and applied cell voltage. The additive, [BMIM]HSO4, was determined to have beneficial effect on the current efficiency, energy consumed in the process and surface morphology of the deposits. The highest current efficiency (92.6%) and lowest energy consumption (2.92kWh/kg) was obtained for solution with 20mg/mL [BMIM]HSO4. The morphology showed the formation of absorbed additive layer on the cathode at higher concentration of additives. Experiments were conducted at different temperatures between 343K and 388K and at various applied cell voltages between 2.7V to 3.6V to determine the best experimental conditions. By varying temperature, highest current efficiency (91.3%) and lowest energy consumption (2.69 kWh/kg) was obtained at 373K. The electrodeposition process is enhanced between the applied voltage 3.0-3.3V by achieving lower energy consumption (2.75~3.06kWh/kg) and higher current efficiency (88.4~89.7%). SEM images showed grain size is significantly increased in higher applied voltages. While at higher temperatures, it seemed to generate particle growth as clusters at the outer deposit layer.

Jan 1, 2014

By J. L. Johnson

The U.S. Department of the Interior, Bureau of Mines, investigated recovery of concentrates containing tin, tantalum, and niobium from the Kougarok deposit on the Seward Peninsula, AK. To date, 25 million lb of tin has been delineated in occurrences containing 0.36 to 1.32 pct Sn, and the resource potential is estimated to be as high as 25 million short tons at average grades of 0.75 pct Sn, 0.025 pct Ta, and 0,025 pct Nb. Deslimed ore was concentrated to 54 pct Sn, 0.3 pct Ta, and 0.3 pct Nb, with recoveries of 74 pct Sn and 44 pct Ta/Nb using a Humphrey's* spiral followed by a Deister shaking table. Tin values in the slimes were upgraded to a 5-pct-Sn concentrate using a Bartles-Mozley separator followed by flotation. The 5- pct-Sn was further upgraded by fuming to give a concentrate containing approximately 60 pct Sn. The recovery of the two products combined was 80 pct Sn and 46 pct Ta/Nb, A flowsheet with mill-design parameters resulted from the metallurgical testing. An economic analysis was made based on the proposed process.

Jan 1, 1990

By Frederick T. Wallenberger

"Laser assisted chemical vapor deposition (LCVD) is a new containerless fiber process whereby growth of small diameter fibers or microstructures (microsprings, microsolenoids) occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber inside the reaction chamber. Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Continuous fibers and multifilament yams are possible. The use -of high reaction chamber pressures (1-10 bar) and a small wavelength Nd-YAG laser made it possible to fabricate small diameter fibers at growth rates >1 mm/s. This paper describes the synthesis of single crystal, polycrystalline and amorphous fibers by LCVD, and provides a comprehensive analysis of phase transformations occurring during their fabrication.IntroductionLaser assisted chemical vapor deposition (LCVD) is a new containerless fiber process [1-10] whereby growth of small diameter fibers or microstructures occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber in the reaction chamber (Figure 1). The diameter of the growing fiber corresponds to that of the laser focus. Depending primarily on the laser energy (Le., the temperature at the growing fiber tip), it is possible to obtain single crystal, poly crystalline or amorphous fibers by this method.Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Laser assisted CVD is a potentially continuous process; continuous fibers and multifilament yams are possible."

Jan 1, 1994

By Seetharama C. Deevi, Mohammad R. Hajaligol, Sarojini Deevi

"Carbides and nitrides of iron are being considered as magnetic materials for high-density recording due to their chemical stability and high-saturation magnetization values (> 100 emu/g). Iron carbides and iron nitrides with magnetic properties suitable for magnetic media were synthesized by employing a novel synthesis procedure based on fluidization of powders in reactive atmospheres. Fluidized-bed reactors of laboratory, bench, and pilot scale were employed for the synthesis of iron carbide, FeSC2, by reducing and carburizing U-Fe203 in the temperature range of 300 to 550 ºC. A temperature of 400· ºC and a reaction time of 2 to 3 h are found to be optimal for the synthesis of iron carbide. When the carburization was carried out in a reducing and carburizing atmosphere such as carbon monoxide, nucleation and growth of FeSC2 occurred directly from Fe304 with no intermediate phases such as FeO or Fe. Longer carburization times resulted in the deposition of carbon on the surfaces of FeSC2 particles due to Boudouard reaction, and higher temperatures favored the formation of a mixture of carbides such as FesC2 and Fe3C. Iron nitrides were synthesized by reducing u-Fe203 in the temperature range of 350 to 550 ºC, followed by nitriding in the temperature range of 350 to 550·ºC. The powders were characterized using X-ray diffraction, scanning electron microscopy, thermogravimetric analyzer, and a vibrating sample magnetometer.IntroductionRecent demand for high-quality recording of optical, electrical, and audio signals generated interest in magnetic tapes with high-recording densities as compared to the conventional magnetic tapes based on U-Fe203. At present, commercially available magnetic tapes contain maghematite, U-Fe203, as a magnetic material with a saturation magnetization of90 emu/g and a coercive force of 400 Oe. Recording of signals at a higher density per unit volume of magnetic material demands magnetic materials with high-saturation magnetization and a reasonable coercive force. Although metallic iron particles possess a saturation magnetization of 130 to 150 emu/g and a high coercive force of 1000 Oe, the gradual oxidation of iron-to-iron oxides (of lower saturation magnetization) prevents the use of iron particles for high-density recording. In contrast, iron carbides such as FesC2, Fe7C3 and iron nitrides such as Fe4N and Fe3N possess excellent magnetic properties coupled with good electrical conductivities and high hardness. The carbides and nitrides of iron have generated significant interest as magnetic materials for the next generation of magnetic tapes due to their unique magnetic properties and relatively greater oxidation resistance as compared to metallic iron particles [1-4]."

Jan 1, 1994

By V. A. Luganav

The behavior of arsenopyrite under heating has been studied by many scientists. It has been already established that under heating at more than 650°c and without air access the arsenopyrite dissociates with the formation of one atom arsenic. Under vacuum the dissociation process begins at 5500C with the formation of elemental arsenic. The residue of dissociation process contains pyrrhotite and throilite. In the presence of pyrite, arsenopyrite dissociates under lower temperature and with a higher velocity than without it. The industrial realization of fool scale processing of arsenic bearing raw materials is possible only by the use of standard equipment and oxygen containing blast. In this view the paper presents the results of the study on the effect of oxygen in the gaseous phase and its addition into the charge of pyrite in the process of arsenopyrite decomposition. Thermodynamic analyses showed that under thermal processing of arsenopyrite in the presence of pyrite and limited quantities of oxygen in the gaseous phase the formation of arsenic sulfides is possible according to the following reactions:

Jan 1, 2003

By Sharif Jahanshahi

Calcium ferrite slags are often associated with Professor Yazawa due to his pioneering work on the thermodynamics of this type of melts. Over the past years CSIRO has invested some effort in studying physico-chemical properties of such melts to fill in some gaps in our knowledge and explore opportunities for application of the understanding developed. These investigations cover thermodynamics, transport properties of calcium ferrite based slags, as well as the kinetics of reactions of such slags with refractories. The present paper provides an overview of some of these studies and highlights some of the interesting behavior of such melts, The oxidation state of copper and arsenic in calcium ferrite based slags are predominantly Cu+ and As3+, respectively, at oxygen potentials below 10-7 atm. The concentration of CU2+ in such slags becomes significant at oxygen potentials of greater than 10-7 atm at 1300 °C. The activities of CuO0.5 and AsO1.5 in calcium ferrite slags show strong deviations from the Raoultian Law, while that of CoO is very close to ideal behaviour with respect to pure solid CoO. Addition of SiO2 to calcium ferrite slags can have significant effects on the activities of FeO and Fe2O3 and hence the stability of magnetite phase. Transfer of oxygen in calcium ferrite slags is fast with diffusivity of 2x 103 cm2/s at 1350 °C and activation energy of 16 kcal/mol. Presence of solid phases, such as magnetite, has pronounced effect on the viscosity of calcium ferrite slags. The observed dependence on solid loading and shear rate indicates deviation from Newtonian behaviour. The interfacial tension between copper mattes and calcium ferrite slags is strongly dependent on the matte grade, with the determined values being much lower than the corresponding ones for interfacial tension between similar mattes and iron silicate slags. MgO, Cr2O3 and MgCr2O4 have low solubility in calcium ferrite slags and their solubility increases with increasing copper oxide content of the slag at 1300°C. The oxidation state of the slag has strong effects on phase transformation, dissolution rate and disintegration of refractories in calcium ferrite slags. Other key factors with major impact on slag-refractory interactions include viscosity and surface tension of slags as well as the contact angle between slag and refractory material,

Jan 1, 2003

By John B. Cocanour

The U.S. Bureau of Mines (USBM) has developed a laboratory-scale on-line analysis and process control system for a decopperization electrolytic circuit. This system is software driven, running on a 486DX-33 personal computer (PC) utilizing a portable energy- dispersive x-ray fluorescence (XRF) spectrometer as the sample analyzer. The XRF copper reading obtained was used as the control variable through an RS-232 serial interface to the PC for software-based control of feed flowrates. When the copper concentration in the electrolytic cell (as measured by the XRF) deviated from the set point, the feed flowrate to the cell was automatically altered using software-based proportional-integral-differential (PID) computer control to yield the desired copper concentration at the electrolytic cell outlet.

Jan 1, 1994

By John T. Berry, Robert D. Pehlke, Michael J. Beffel

"Pattern making and metal casting organizations are currently adopting CAD/CAM systems and implementing this technology in design and production. Al though significant progress has been reported, these systems generally are based on two or two and one half dimensional analyses. Very few are based on solid geometric modelers.The present paper emphasizes the need for solid geometric modeling of the casting and rigging system and linkage with a solidification simulator. The nature of some of the technological challenges which have slowed this development are discussed, including accurate description of complex surfaces and their intersections and the bridging of computer encoded information with NC technologies and with FEM-based simulators for stress and thermal analyses. A recently prepared modular-structured FEM simulation code implemented on a micro computer is described.Construction of a solid geometric model of the casting and rigging and validation of the combination for optimum characteristics of soundness, quality and yield by solidification simulation are I inked as key elements in the foundry of the future. Data base support for this CAD/CAM system is rapidly being developed throughout the world.INTRODUCTIONThe simulation of shaped casting solidification using the digital computer, goes back to at least the early nineteen-sixties when Forsund (1) in Denmark applied the technique to the problems of casting surface quality.Prior to that time, the work of Paschkis and co-workers using the analog computer ranges back to the nineteen-forties, when work sponsored by the AFS Heat Transfer Committee at Columbia University revealed many hitherto unknown or only partly anticipated aspects of casting solidification (2).Three reviews of the various historical aspects of simulation should be referenced. Firstly, the AFS monograph by one of the present writers (RDP) and his colleagues - describing background and later work, again sponsored by the AFS Heat Transfer Committee at the University of Michigan (3). Secondly, a review prepared by Durham and Berry (4) which discusses broad aspects of casting solidification simulation. Thirdly, a review by Erickson (5) which contains an excellent bibliography to 1980. In addition to these papers, the publications lists of the CADCAST project* and the proceedings of the two Engineering Foundation Conferences of Casting and Welding Modeling, published by ASME, are also most notable (6) •"

Jan 1, 1986

By Liyuan Chai, Qin Liu, Bing Peng, Jia Wang, Qiang Zhang

"Electrolytic Manganese Residue (EMR) was used as the main material to prepare cementing material activator for the utilization of the residue from electrolytic manganese dioxide (EMD) or electrolytic metallic manganese (EMM) production. The effects of chemical activation, thermal activation and mechanical activation on retarding activity and excitation activity of EMR were investigated according to the setting time and activity index of EMR-slag cementing material. The results showed that the EMR exhibited good activating performance after being ball-milled for 18 min and then treated for 1-2 hours at temperature range of 350-450 ?. The optimal properties of cementing material activator were achieved at the weight percent ratio 30 : 3 : 5 of EMR/Ca(OH)2/cement clinker.IntroductionMany hazardous industrial solid wastes such as blast furnace slag, fly ash, steelmaking slag, chromic slag and electrolytic manganese residue [1] are generated n China and their amounts increases every year. The accumulation of the solid wastes during past years is very huge and they could be hardly recycled effectively as a sustainable resource. 2.35 billion tons of industrial solid wastes have been produced up to now [2]. It is estimated that they would exceed 3.3 billion tons by the end of 2015 [3]. On the other hand, the quick development of Chinese infrastructural construction needs more cementing materials. The production of traditional building materials consumes lots of natural resource such as clay and limestone and discharges at least 1 ton CO2 and other pollutants per ton clinker [4]. Therefore, it is necessary to develop new types of cementing materials instead of clinker [5,6]."

Jan 1, 2012

By Wilhelm Brandstätter, Johannes Steiner, Alois Triessnig, Christian Redl

"The results of numerical simulations of bubble detachment from an orifice in a horizontal plate submerged in liquid are presented. The bubbles are created by forcing gas through this orifice into stagnant liquid. The simulations are performed with a two-dimensional incompressible Lattice Boltzmann (LB) scheme. In previous works the same problem was investigated by two-phase simulations in which surface tension effects were considered by an interaction potential formulation between the phases. In contrast, in the present work a volume of fluid (VOF) model consisting of a carrier fluid and a passively advected scalar function for the calculation of gravitational and surface tension forces, respectively, is used. The aims of this study are to examine the applicability of the one-phase LB method to the numerical analysis of bubble formation and to verify the theoretical and experimental predictions of the dependencies of the departure diameter on gravitational forces, surface forces and wettability effects. To this purpose the simulations were performed at different values of gravitational acceleration g, surface tension coefficient s and contact angle ß. Nonlinear fits to the data yield functional dependencies which are in good agreement with the predictions. IntroductionBubble formation behavior is an extensively studied subject, especially in chemical engineering, power industries and metallurgical processing. Knowledge of the underlying physics of bubble motion is, for example, required for the design of chemical reaction towers and agitation tanks. Another important application is the argon gas injection through the wall of the tundish nozzle into liquid steel stream to deter clogging with solid inclusions. Argon bubble motion and its effect on flow depends greatly on different parameters, e.g. gas flow rate and size of the bubbles. Thus, if these bubbles are not managed properly, they can become encapsulated upon solidification and result in undesirable impurities in the material [1, 2]."

Jan 1, 2004

By M. Drozd

Multi-use pad operators require an efficient and economic method to destroy cyanide in their process residues so new material can be stored on the pad and leached. Operators of the dedicated or single-use pads require an effective cyanide destruction method for pad closure. Cyanide destruction can be accomplished by utilizing oxidants such as hydrogen peroxide or calcium hypochlorite, or by utilizing ferrous sulfate which sequesters the cyanide in strong acid dissociable complex. Ferrous sulfate can be the preferred method of cyanide destruction because it is a less costly chemical, reaction rates are almost immediate and unlike oxidants, it can penetrate the total depth of a pile without being destroyed by side reactions. Literature indicates that the (Fe(CN)6)-4 com~lex is produced slowly but it appears that complexes such as Fe(CN)4(H20)2-or Fe(CN)4(OH)2)-4, are formed quickly and should have no U.V. sensitifity, unlike (Fe(CN)6)-4. Stoichiometry of the testwork indicates that Fe«CN)4(OH)2)-4 complex may be the species formed. The usage of ferrous sulfate has the advantage of being able to bring ~ level down that divalent metal ions such as Cu++, Cd++, Hg++, Pb++ and Zn will form insoluble complexes and precipitate from solutions does not destroy weak acid dissolvable complexes and can leave a heavy metal problem behind after cyanide destruction.

Jan 1, 1990

By SM Rao

Nuclear Fuel Complex (NFC ) , Hyderabad (IN DIA ) , is engaged in the manufacture of nuclear fuel assemblies and zircaloy structural components required for the Indian nuclear power reactors. The production of zirconium oxide, sponge and zircaloy materials through chemical and hydro - metallurgical processes generates many effluents containing valuable zirconium and hafnium . This paper deals with the various processes such as multiple crystalization, phosphate precipitation, ion-exchanges amine solvent extraction etc, for the treatment of these effluents and subsequent recovery of valuable zirconium and hafnium .

Jan 1, 1992

By Florian Kongoli

New operating conditions and process parameters are often necessary in today's industrial practice of non-ferrous smelting and converting in order to accommodate various new chemical compositions of mineral charges and environmental requirements or to conceive new and more efficient industrial technologies. An important parameter in non-ferrous smelting and converting is the liquidus surface of multicomponent slags. This surface is affected by multiple factors such as temperature, gaseous potentials, the content of each component in the slag, etc., and cannot be quantified by the existing ternary liquidus diagrams. In this work a new type of representation of the liquidus surface of multi component systems has been presented by means of a thermodynamic model. This representation waives the need of the multidimensional representation of multi component systems and yields practical two-dimensional diagrams, which can be easily used in the industrial practice.

Jan 1, 2000

By K. Knuutila

The behaviour of thiourea, animal glue and chloride ions in the electro¬lysis of copper has been investigated by various different electrochemical experiments, i.e. polarization curves with stationary copper electrodes, long-time galvanostatic electrolyses and Hull cell experiments. Polarization curves with stationary copper electrodes show that animal glue has a polarizative effect on the deposition potential. Small thiourea contents affect depolarizatively when high concentrations retard the copper deposition. The microstructures of the deposited copper after the long-time electrolyses show that animal glue favours a basis oriented deposition structure. With thiourea the field orientated structure was evident. It was also observed that the deposited structure depended much on the grain structure of the starter sheet. The chloride ion concentration has a drastic effect on. the crystal size of the deposited copper as it was found out in Hull cell tests. Chloride ions flattened the the crystals and the deposition became smoother when the chloride ions were added. The cathode copper quality is discussed according to the literature. Special attention is paid on the codeposition of thiourea and the origin of sulphur impurities in copper cathodes.

Jan 1, 1987

By A. Rosenfeld

The feasibility of applying laser induced optical emission spectroscopy to the high speed sorting of mixed alloy aluminum scrap is investigated. The basic spectroscopy for analysing aluminum alloys for the major alloying elements over their full concentration ranges is established. Materials handling issues are also described and the components of an overall sorting system are presented.

Jan 1, 1995

By M. Friák, L. G. Wang, M. Šob, V. Vitek

"The paper gives an account of applications of quantum-mechanical (first-principles) electronic structure calculations to the problem of theoretical tensile strength in metals and intermetallics. First, we briefly describe the way of simulating the tensile test and the electronic structure calculational method. Our approach is then illustrated on calculations of theoretical tensile strength in W, NiAl and transition metal disilicides MoSi2 and WSi2 with C11b structure. In Wand NiAl, we consider uniaxial tension along [001] and [111] directions. Although tungsten is elastically nearly isotropic (C44 = C”), theoretical tensile strength exhibits a marked anisotropy (oth/001 = 29 GPa, o'th/111 = 40 GPa). Calculated results compare favorably with experimental value of 24.7±3.6 GPa obtained for tungsten whiskers grown along the [110] direction. Similarly, in NiAl, the 'hard' orientation [001] differs very significantly from the [ill] orientation (oth/001 = 46 GPa, oth/111 = 25 GPa). This anisotropy is explained in terms of higher-symmetry structures present or absent on the calculated deformation paths. In disilicides, the theoretical strength is calculated for [001] loading (oth/001 = 37 GPa and 38 GPa for MoSi2 and WSi2 , respectively). The role of relaxation of internal structure parameter is discussed and changes in bonding conditions during the tensile test are analyzed.IntroductionIn most engineering applications, the strength of materials is limited by the presence of internal defects. If there were no defects, then, for example, the tensile strength could be several orders of magnitude higher and its value would be comparable with that of shear modulus. Therefore, the strength of ideal (defect-free) crystal represents an upper limit of attainable stresses, which is called the ideal strength. While it may not be possible to achieve the ideal strength in practice, it is not possible to exceed it. However, the ideal strength is already approached in situations which are technologically relevant. These include the low-temperature deformation of inherently strong materials, such as diamond, Si, Ge and some of the transition-metal carbonitrides, deformation of whiskers, nanoindentation of materials with low defect densities, hardened thin films and coatings etc. The ideal strength sets the limits of elastic stability of a solid. Its knowledge is useful for estimation of the ideal work of fracture stresses needed for homogeneous nucleation of dislocations and for modelling of crack propagation."

Jan 1, 2001

By R. Tunold, Y. J. Zhang

"The cathodic kinetics of aluminum deposition from aluminum chloridealkali chloride melts was studied by use of electro-cnemical transient techniques at 700 °C. Aluminum deposited as an insoluble product on a glassy carbon electrode and as a partly soluble product on a tungsten electrode. The deposition was found to be a simple diffusion controlled process involving the exchange of three electrons. The diffusion coefficient of aluminum chloride was calculated - 4.sx10-s cm2 ·S-I in AlCl3 -NaCl-LiCl melts and 2.6x10-s cm2 ·S-' in AlCl3 -NaCl-KCl melts. For AlCl3 -NaCl-CsCl system the diffusion coefficient exhibited some uncertainty due to nucleation. The determined rate constant of aluminum deposition reaction was on the order of 10-' -10-2 cm'S:' Constant potential electrolysis was carried out. TiB2 was well wetted by aluminum. The species of melts penetrated into graphite and glassy carbon but not into tungsten. The diffusion coefficient of species in glassy carbon was evaluated.IntroductionAluminum chloride electrolysis is attractive for its power saving of 30%. Different process to circumvent the conventional chlorization to obtain aluminum chloride economically, such as directly chlorizating mixture of Al~03 and C in a cell with A-shaped laminated bipolar electrodes by rising chlorine (1), or by use of a composite anode (2), will promote the electrolysis technology to be realized industrially. With the appearance of the Alcoa process periodically there are studies on the kinetics of aluminum deposition. Some discrepancies seem to exist on the mechanism of aluminum deposition. Borne studies (3,4,5) showed that the deposition of aluminum was hindered by diffusion process in the melts. M.Gabco et a1. (6) claimed a preceding dissociation of a complex being the rate controlled step. This paper presents our results on the mechanism of aluminum deposition from the study by use of transient techniques and some results from constant potential electrolysis."

Jan 1, 1988

By Zhengjie Chen, Wenhui Ma, Jijun Wu, Kuixian Wei

The gasification reactivity of PC (petroleum coke), strengthened by addition of different potassium carbonate proportions using different grinding medium, was investigated by using thermogravimetric analysis (TGA). Results showed that the gasification reactivity of PC not only increased with the increase of catalyst-loaded, but also showed the effective improvement by anhydrous alcohol. The PC was mixed with potassium carbonate [K2CO3] catalyst at 0.5%, 0.8%, 1.0% and 1.5%, and then ground wet with distilled water. The CO2-gasification rate of PC was only 77.35%, 80.55%, 84.07% and 85.88% under the gasification temperature 1100 °C and holding time 120 min, at different K2CO3 respectively. However, when the PC was ground in anhydrous alcohol at the same condition of catalyst-loading, the gasification rate of PC reached 95.43%, 96.63%, 95.50% and 95.61% at the holding time of 108 min, 101 min, 74 min and 35 min, respectively. It was shown by FTIR, SEM and EDX determinations that the anhydrous alcohol used as the grinding medium can further improve the gasification reactivity of PC when compared with the distilled water.

Jan 1, 2016