Search Documents

By Jerry R. Riding

Metallurgical process methods have seen dramatic improvement over the past fifty years. As these improvements have come about, more and more emphasis has been placed on obtaining accurate and rapid analysis of the metallurgical processes. Well-defined conventional laboratory analysis procedures which have proven to be reliable were developed early in the mineral industry's history; however, these conventional procedures, which have not changed appreciably in fifty years, have the serious drawback that they are too slow to be of appreciable value in automatic control of the processes. For example, the assay results normally become available to a mill operator from eight to twenty-four hours after a sample is taken. Since the desired mineral separation can only be made while the minerals are in the flotation circuit, conventional assay results provide information similar to postmortem reports. Consequently, using conventional procedures, the mill is operated with information from an earlier period of time, which may not reflect current conditions. In recent years there has been a steady increase in the volume of required samples. At the same time, labor, material, and overhead costs have continued to rise causing the cost per assay to reach an alarming level. This rising cost per assay, plus the increasing demand for rapid analysis necessary for control, has caused the mining and metal processing industries to look toward other techniques to solve these problems As a result, X-ray fluorescence which can provide on-stream analysis necessary for control, as well as perform numerous laboratory assays at lower cost and at a much greater speed than conventional methods, has gained wide-spread attention. In addition, multichannel X-ray fluorescent instruments are now available which have been perfected to the point where the analysis of the most important chemical constituents is available within one minute after a sample is presented to the X-ray analyzer. Because of these obvious advantages, extensive use is being made today of X-ray analysis in the mining industry to analyze slags, ores, and mineral content of rocks. The results are used to make quick decisions for both mining and beneficiation of metals. For example, X-ray systems which provide rapid on-stream analysis of the slurries at desired points Fn metallurgical processes have recently been developed. The successful application of these systems has moved the milling process a step closer to fully automatic control.

Jan 1, 1969

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By A. D. Hammond

Vanadium is a transition metal, ductile and silver-gray. It is harder than most metals and steels and it has a good resistance to corrosion. It is stable against alkalis and sulfuric and hydrochloric acids. Vanadium is oxidized in air at about 660° C (1,220° F), although an oxide layer forms even at room temperature. The chemistry of vanadium is noteworthy for the accessibility of the four adjacent oxidation states, 2-5. In aqueous solution, the colors are lilac V2+, green V3+, blue VO2+ and, at high pH, yellow VO42-. Considered to be as abundant as zinc, metallic vanadium is not found in nature, but it is known to exist in about 65 different minerals. Economically significant examples include patronite (VS4), vanadinite (Pb5(VO4)3Cl), associated to the uranium mineral carnotite (K2(UO2)2(VO4)2?3H2O) and in a vanadium mica called roscoelite K(V3+,Al,Mg)[(Si,Al)4O10] (OH)2. Other important vanadium ore oxides are montroseite (V,Fe)O(OH) and corvusite (Na,Ca,K)V8O2.4H2O. Much of the world?s vanadium mine production comes from magnetite-hosted deposits and, to a lesser extent, sedimentary-hosted sandstone.

Dec 1, 2013

By H. E. Hirsch

Propelled by the invention of the transistor at Bell Laboratories, germanium's unique properties have advanced our electronic world by many years. Germanium has found major uses in infrared optics, fiber optics and a revised vigor as a catalyst for PET plastic production. Other advanced applications are in various stages of development. The solid state electronics industry has been the driving force behind the accelerating demand for gallium since the late sixties. Past developments of substrates for light emitting diodes, lasers and magnetic bubble memories are paling in view of the current excitement over the use of semi-insulating gallium arsenide for high performance integrated circuits. This application requires gallium metal and gallium compounds of extraordinary purity.

Jan 1, 1986

By R. Brown, A. J. S. Spearing, M. Treinen, M. Theisinger

The mining and use of coal creates a significant amount of waste material that needs to be safely disposed of. It is likely that in the medium term, the Environmental Protection Agency (EPA) in the U.S. will categorize all such products as a new category – special waste. This would make the materials subject to many of the requirements for handling toxic waste, which will complicate the disposal of such products and significantly increase the disposal costs. Underground disposal would, therefore, seem to be the obvious solution, especially if the placed material can have low or no permeability, so that water table pollution does not present a serious long-term issue after placement. Significant additional advantages could be derived from this backfilling, including the reduction or elimination of surface subsidence, increased extraction, reduced surface waste disposal footprint and the elimination of explosion-proof seals in worked out areas. The research using a specific coal waste product as a typical example proved that the method of placing the backfill at a high density with low permeability is technically viable, but it must be made more cost effective and the other potential benefits quantified and costed in order to present a true comparison.

Jan 1, 2010

By Christoph Schulte-Schrepping, Bou-Young Youn, Rolf Breitenbücher

"The main requirements of two-component grouts are a high workability and sufficient stability against sedimentation with a retention time of more than 72 hours, as well as a rapid strength development im-mediately after grouting. Component A usually consists of OPC, water, bentonite, and retarding agent. Component B, a liquid accelerator, is added to Component A during grouting at the end of the shield tail. Current investigations on different compositions of Component A showed a high workability lasting for at least 72 hours. The workability could be extended with increasing amount of the retarding agent to a certain degree. An increase of the bentonite content improved the stability of the mix, but had a negative impact on the flowability respectively the workability of Component A. High compressive strengths could be rather achieved by an adapted mixing ratio of Component A and B than by increasing the amount of the accelerator. Thereby, the interactions and compatibility of the selected constituents play an essential role. INTRODUCTION In mechanized tunneling with segment linings, the annular gap between segment ring and soil must be filled instantaneously with an adequate grouting mortar. The main functions of the annular gap grouting are to stabilize the tunnel lining and to minimize settlements of the ground surface at the same time. Thereby, two contradictory requirements are demanded on annular gap grouts: On the one hand a high workability and sufficient stability against sedimentation, on the other hand a rapid strength develop-ment immediately after grouting. Besides single-component grouts, which achieve the necessary stiffen-ing by dewatering into the surrounding soil, two-component grouts are used, especially in cohesive soils with a very low permeability. Basically, annular gap grouts are almost exclusively defined on empirical basis. Fundamental studies about the constituents and composition of the grout as well as the related achievable properties are still missing so far. Therefore, it is necessary to investigate the material-specific correlations regarding the relevant parameters of annular gap grouts – workability and flowability, stability of the mix as well as strength development – in comprehensive experiments. Based on the knowledge gained from the investigations, it should also be possible, to perform the grouting material according to a real design concept and thus, to ensure an adequate grouting in prac-tice considering the geological and hydro-geological conditions."

Jan 1, 2016

By Richard M. Chamberlin

Perlite is an altered rhyolitic glass with 2 to 5 wt % water that expands or "pops" when heated quickly to plasticity while evolving steam to form lightweight, glass foam. Commercial perlite deposits in New Mexico are well-developed zones of chemical weathering (hydration) superimposed on highly permeable and thick glassy zones at the chilled upper surface and toes of high-silica-rhyolite lava flows and lava domes. The maximum tonnage of glass in these volcanoes was predetermined by their unique eruptive histories. New Mexico perlite production (80% of US production of 571,00 st) is mostly from the 3.9 Ma high-silica-rhyolite lava flows at the No Agua Peaks volcanic center. The primary vent at No Agua is defined by a 900 ft-high rubidium-rich composite lava dome, known as West Peak, that contains minor perlite reserves. Slightly less rubidium-rich lava squeezed out from under the west flank of the dome to form relatively thin (250 ft) but highly vesicular lobate flows that now consist of about 50 % recoverable perlite. Finally, rubidium-poor lavas were extruded from a radial dike on the northeast flank of the dome. These thicker (400 ft) flow lobes contain about 20 % recoverable perlite. The largest mass of lava does not always contain the most perlite. The thinner (west) flow at No Agua yields the largest perlite reserves rather than the large composite lava dome or thicker (east) flow.

Jan 1, 1994

By J. C. Stankus

Many coal seams are associated with soft floor strata and during mine development if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One of the methods for controlling floor heave is floor bolting. This paper describes the demonstration of floor bolting methods in a West Virginia coal mine. Three methods were used: (1) vertical full resin bolting, (2) floor truss bolting, and (3) floor truss bolting plus a floor cut at the center of the entry. The design of each method and the experimental results are discussed in detail.

Jan 1, 1993

By L. M. Kocher, J. R. Heberger, J. P. Pollard, M. F. Nasarwanji

Injuries associated with hands and fingers are highly prevalent in mining and identifying factors associated with these injuries are critical in developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011–2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53%) followed by bone fractures/chips (26%). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals (pipe, wire, guards) and hand tools as the primary sources of hand and finger injury. Although information on glove use was limited, leather gloves were most often worn when an injury occurred. When worn, gloves were found to contribute to 20% of the injuries, indicating their potential to protect the hands, but also potentially put the hands at risk. Further research is necessary to determine performance requirements for gloves used in mining operations, specifically those offering cut and puncture resistance.

Mar 2, 2022

By G. M. Bernard

The Andacollo gold mine is located near the small town of Andacollo, Chile (population 14,000) in the fourth region. It is approximately 35 miles by paved road from the coastal city of La Serena, and Santiago lies about 300 miles to the south (see map.) Site elevation varies between 3300 feet and 4200 feet. The climate at the site is moderate but arid, with an average annual rainfall of only five inches. Because there is little rain, and the temperature varies only a few degrees (57"F to 75°F); there are no freezing, solution dilution, or pad saturation problems. The climatic conditions are ideal for heap leaching.

Jan 1, 1996

By J. Kemeny, K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in an area of the mine that contains argillite and is relatively homogeneous. This process also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for argillite will be updated as more tests are conducted, and the model will be extended to the four other primary rock types at the Asarco Mission mine.

Jan 1, 2011

By K. L. Gabby

Selective removal of mercury from cyanide leaching solutions while retaining silver has been a long-standing problem, due to the chemical similarity of mercury and silver. In order to be practical, a mercury removal process needs to be both highly selective and use inexpensive materials. This paper reports the use of zinc sulfide (ZnS) as a precipitant for mercury. The mercury cyanide complex (Hg(CN)4 2-) undergoes a replacement reaction with the zinc sulfide, forming insoluble HgS, while the silver cyanide complex (Ag(CN)2 -) remains in solution. Under appropriate conditions, the separation of mercury from silver is nearly quantitative, with close to 100% removal of mercury, while nearly none of the silver is precipitated.

By Donald R. Williamson

Statistical studies at Cyprus Pima Mine indicate that samples from 22 blastholes are necessary for determining average copper grades, within a desired range of precision, for mine-model blocks by arithmetic averaging. The average number of holes in such blocks is 14. Many considerations show that more holes will not be drilled for sampling. A way to determine block grades more reliably than by" arithmetic averaging was sought. Thus far arithmetic averaging has proven to be the best procedure for the particular operation characteristics despite the small number of samples. It naturally follows that expenditure of great effort in sampling blasthole cuttings is unwise.

Jan 1, 1977

By S. Mohanta, S. Chakraborty, B. C. Meikap

"An air dense medium fluidized bed separator is an efficient dry process for the removal of undesirable gangue material from run-of-mine coal. Its cleaning performance depends on a variety of operating parameters that are interrelated in unknown, complex ways. A literature review showed that these parameters' effects had been experimentally investigated using a traditional one-variable-at-a-time approach, which is highly inefficient and sometimes misleading because many of the parameters often interact with each other to alter the overall equipment performance. Also, it is realized that the interrelationship among these parameters can have a significant effect on equipment performance. Therefore, to correctly evaluate the effects of individual parameters as well as their interactional effects on the separation performance of an air dense medium fluidized bed, we conducted a scientific study based on response surface methodology. Empirical models for two key response variables, namely, product ash and combustible recovery, were developed and subsequently used for identifying an appropriate operating region to achieve optimum separation performance. Furthermore, the optimum performances predicted from the empirical models were validated against experimental data. Preliminary results show a strong interaction among the operating parameters investigated in this test program.IntroductionFluidization is widely applied in industry for its various useful features. In the coal industry, it is used in the air dense medium fluidized bed (ADMFB) separator for the beneficiation of run-of-mine coal. In this separator, a medium is created by suspending fine magnetite particles in an upward air flow, and this pseudo-fluid is used as the beneficiation medium, with the lighter coal particles floating to the medium’s surface while heavier particles sink to the bottom. This separation technique had been receiving a significant amount of attention worldwide in recent times for its specific advantages of low operating cost and less restriction for small capacities (Luo and Chen, 2001; Sahu et al., 2009; Dwari and Hanumantha Rao, 2007; Van Houwelingen and de Jong, 2004), but it is still not a well-established industrial practice because of the availability of efficient wet processing technology. However, with a revival of interest in the dry beneficiation of coal, in general, and ADMFB, in particular, there is once again a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have been made to make this process a competitive and viable option. The existing literature reveals that most of these research efforts had been essentially focused on the identification of a single parameter that has a key influence on separation performance, without taking notice of parameter interactional effect. For example, Luo et al. (2004) proposed a pressure drop number to distinguish separation performance without considering the bed height and gas velocity, which are intimately related to this proposed pressure drop number."

Jan 1, 2015

By Peter N. Calder

There is little doubt that the stability of both highwalls and spoil piles is essential to efficient strip mining. Accurate determination of the appropriate geotechnical parameters will pay dividends during mining, but only if the mine operation closely follows the engineering plans which have incorporated These factors. Productivity is invariably higher in mines where failure of highwalls and spoil piles does not occur. This is the result of the reduced rehandle and better working conditions found in stable mines. Control of the waste piles and highwalls also leads to better coal recover since failures can result in the burial of uncovered coal, which is then lost to mining. Safety is an important consideration. The importance of providing a safe working place for employees and of protecting costly mining equipment is hard to overemphasize. For miners, working in areas where instability exists, the degree of hazard involved in their occupation is increased particularly where night operations are involved. It is true, too, that there have been many cases where loading equipment has been buried and severely damaged by failures.

Jan 1, 1980

By W. A. Haley

Wheel loaders became important bulk materials handling tools in the early fifties. As they grew in stature, productivity, reliability, and acceptance, the demand for larger, more rugged machines evolved. In the early sixties, the introduction of a 6-yard model by a major equipment manufacturer led quickly to widespread experimenting and rapid worldwide acceptance in loading blasted rock in stone quarries and smaller metal mines. As the wheel loaders grew in popularity for shot rock loading, larger models, 12- to 15-yard size were developed and saw widespread use by 1970. In the past 20 years, at most quarries and small to medium size mines, most cable operated power shovels have been replaced by large wheel loaders and more recently, hydraulic excavators as the primary loading tool. Wheel loaders larger than the 15-yard class are not used widely. Until about 1970, very few overburden haulage trucks were used in domestic coal mines. About that time, many states started enforcing stringent mine relcamation regulations and in 1977, even more stringent federal legislation was passed. These controls brought about drastic changes in coal surface mining methods in the mountainous areas of Appalachia, in smaller midwestern mines and in the large mines of the western states. Basically, simple material casting methods were replaced at most eastern mines by "haul-back" and "mountain top mining" methods using controlled placement of overburden as it is removed from the coal. These methods dictated much more extensive use of loaders/ shovels and trucks to the point that most coal mining in those areas is now by loader/shovel trucks methods. And those areas have become the home of the country's largest population of large wheel loaders and trucks in the 35- to 85-ton size class with a trend to even larger trucks and shovels. To maintain equal production or provide for growth, the new methods have caused a sharp increase in machine intensity to the extent that at some mines, up to three times as many machines were required to mine a million tons of coal in the late seventies as compared to the machine needs in the sixties. Mining costs and coal prices also took a big jump in the mid-seventies, paralleling the drastic price increases in oil and other forms of energy.

Jan 1, 1984

By R. J. Lee

Asbestos analysis is conceptually simple. The objective, in most environmental analyses, is to determine the number of asbestos fibers per unit area or volume in a sample. The sample may be a consumer product, an ambient air sample, or a water sample. This determination is complicated by several factors including sample collection and preparation, counting techniques, and the operational definition of asbestos in use. Three different definitions have been used in the study of environmental samples; these are summarized in Table 1. [ ]

Jan 1, 1979

By Bo-Hyun Kim, Mark K. Larson

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) have advocated the use of instrumentation in underground mine ground control studies to aid in understanding failure mechanisms and to calibrate numerical models. The purpose of these efforts is to reduce accidents and fatalities in underground mines resulting from inadequate design of mining layout or supports. A recent examination of some results of stress change measurement raised some questions about the validity of elastic solutions in ground, such as coal. Particularly under deep cover as is prevalent in the western United States, the coal around a borehole would likely have yielded so that post-yield behavior would govern the response of the instrument.A numerical experiment was conducted by NIOSH researchers using the FLAC software (Itasca Consulting Group, 2016) to investigate the response of the borehole pressure cell (BPC) and the biaxial stressmeter to varying degrees of plastic behavior. The pre-encapsulated BPC cell pressure exhibits increasing departure from the elastic case with decreasing post-peak-strength slope of the stress-strain curve. On the other hand, because the BSM usually provides much more confinement to the surrounding rock than does the BPC, the measurements obtained from the BSM do not depart significantly from the changes in secondary principal stresses and directions as calculated by the elastic solution.INTRODUCTIONSeveral years ago, Larson et al. (2000) described several instruments that NIOSH had used in underground field studies and how to monitor them with dataloggers. This information is still relevant because of the need to understand how excavation affects the stability of mines and thus, the safety of mining personnel. One class of instruments described in that paper includes those instruments that measure change in rock stress. Although several such instruments might be used to measure stress change, the focus of this paper is on two instruments with which NIOSH has had more recent experience—the borehole pressure cell (BPC) (Geokon, 2018a; RST Instruments, 2018) and the biaxial stressmeter (BSM) (Geokon, 2018b). Other instruments, such as the CSIRO hollow inclusion stress cell (HICell) (Earth Sciences, 2019; Worotnicki and Walton, 1976) may be included in future studies.Early studies in the development of the BPC were those of Panek and Stock (USBM, 1964), Sellers (1970), Lu (1984), and Babcock (1986). Babcock’s work is particularly useful, but his setting and testing range was far below what we experienced in the NIOSH study, and it was Babcock’s data reduction scheme from his laboratory experiments that was used to calculate stress change in the NIOSH study (NIOSH, 2019a)."

Jan 1, 2019

By R. S. Kasper

This paper reviews the procedure used to quantify the conveyor frictional resistance on a 3.9 km (2.4 mile) long overland conveyor belt. Field torque measurements of the three drives were used to help fine tune a computer simulation of the conveyor. This enabled the prediction of the effect on various conveyor components that cold temperatures will have on increasing the throughput tonnage.

Jan 1, 1995

By A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to a reduction in travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation nay be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways nay contribute to formation. The study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Company to identify causes of the problem.

Jan 1, 1982