Search Documents

By M. D. Mwema

Copper oxide ores deposits in the Katanga province of the Democratic Republic of Congo (DRC) contain at variable level cobalt oxide minerals. In contrast to copper oxide minerals which readily dissolve in the sulphuric acid solution, the cobalt oxide bearings are difficult to dissolve, especially if cobalt is present in the third oxidation state (Co2O3). This species become soluble after reduction of Co+3in Co+2. In practice, the use of reducing agent is therefore necessary in order to transform the insoluble minerals into soluble cobalt sulphate species. The following reducing agents are currently used at the Shituru plant: ferrous ions, which are present in leach solutions, pulverised copper or sodium meta bisulphite (MBS). Due to the high consumption of reducing agents (0,8 t MBS/t of solubilized Co; 1,2 t Cu/t-Co), cobalt production is expensive. The use of sulphur dioxide as reducing agent was then investigated in order to reduce operating cost. This reagent also presents the advantage of sulphuric acid production during the leaching process. It has been added in the leaching vessel (tank). From the laboratory and industrial tests, selective leaching of cobalt (78%) has been performed. The cobalt leaching kinetic depend on sulphur dioxide dosage. Dissolution of copper, iron and manganese remained very low. No emanation of SO2 gas was observed during the process.

Jan 1, 2002

Council for 2005/2006 President W.H. van Niekerk President-elect R.P.H. Willis Vice-presidents Senior R.G.B. Pickering Junior A.M. Garbers-Craig Immediate Past-president F.M.G. Egerton Honorary Treasurer J.A. Cruise

Jan 1, 2006

By G. van Aswegen

Seismic monitoring became commonplace in the deep South African gold mines in the early 1990’s. The discipline has, to a large extent, developed beyond the ‘research’ stage, and a ‘Guide to Seismic Monitoring in Mines’ has been accepted by the Department of Minerals and Energy1. Although ongoing research is a requirement for the achievement of all the objectives of seismic monitoring in mines, sufficient knowledge exists to apply seismic monitoring for routine seismic hazard assessment as an aid to risk management. The design and management of seismic monitoring systems can be tested against requirements spelled out in the ‘Guide’. Assuming the seismic monitoring system performs as per requirement, the best practice for routine seismic hazard assessment in mines includes • Long term seismic hazard assessment: through back analysis of seismic data and correlation with numerical modelling output, reasonable tests for planned mine designs are possible. • Medium term seismic hazard assessment: o Spatial analysis through contouring of seismic strain related parameters, with superimposed contours or event plots of stress related parameters allow the delineation of potential instabilities in space. o Quantitative and statistical analyses of seismicity in smaller spatial units (usually encompassing production sites) allow the comparative seismic hazard rating of different areas/sites so that rock engineering input and risk management can be optimised • Short term seismic hazard assessment relies mainly on time history analyses of particular seismicity parameters. The temporal patterns are controlled by a combination of temporal and parameter filters, the optimisation of which determines the success rate.

Jan 1, 2003

By M. S. Smith

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The condition of tunnels at Premier has deteriorated to such an extent that an objective viewpoint on what leads to poor condition was required. Poor and untimely development results in schedule deviation, rehabilitation, and increased working costs. The project focused primarily on quality, and not on efficiency. The project gave management guidelines that need to be focused on in order to produce quality infrastructure. The conclusions were reached by doing literature searches, underground site investigations, benchmarking and computer simulations. From the results we can see that, in order to produce good quality tunnels, we have to have the basics working. This was found to be one of the major problems. Firstly, tunnel profiles are not to the design specification and no fixed blast designs existed. After revising tunnel profile statistics, over break increased to 10% (previously 7%) and development metres were 50 m short of target. Blasting was not monitored and designs not optimized for the conditions. Furthermore, geological factors are the main contributor to tunnel failure, although this process is initiated and aided by poor development (overbroken tunnels, incorrect profiles, direction and location) and blast damage. Continuing to develop tunnels in the current manner will cost R 1.5 million in additional costs for loading and supporting overbreak, whilst an additional 1 800 man-shifts will be required. Blast patterns were designed as a starting point for trials, while the implementation of a blast management system, development statistical database, tunnel hand-over procedures and a revision of the bonus system were proposed.

Jan 1, 2004

Ongoing rockpass problems on mines within the South Africa region, prompted AngloGold Ashanti to embark on a risk assessment of major rockpasses. This commenced with the collection of relevant data to identify gaps in the available knowledge and identify existing problems. This was followed by an assessment of rockpass layouts to determine existing and potential interactions with other excavations. An initial risk assessment has been completed and the rockpasses have been ranked in terms of their risk profile. The lack of geological data and an easy and reliable method of surveying rockpasses have been identified as problem areas. Shortcoming is terms of rockpass management procedures have also been identified. Further work is required to quantify the risk in terms of probability of occurrence and consequences.

Jan 1, 2005

By S. V. Rungan

Since 1994, South Africa has been the subject of international attention, especially in regard to its transformation initiatives, which aim to redress the post-apartheid imbalances. Mining, as a major employer and one of the major industries in South Africa, has been the focus of the government?s Black Economic Empowerment initiative with the introduction of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The historical background to South Africa?s transformation and the role of the mining industry are pivotal to an appreciation of certain aspects of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The issues around Black Economic Empowerment and the enabling of a smooth transition to the South African mining industry of the future are explored in this paper.

Jan 1, 2005

By J. Glazewski

The mining industry in South Africa has developed its own environmental guidelines in the form of an Aide-Mémoire1,which is an extension of the previous rehabilitation provisions to include all aspects of the environment and all phases of a mining operation. This development, at the time, recognized an international trend towards the formalization of environmental management in mining practice, which resulted from the realization of the large environmental liabilities that mines could face, particularly on closure. Over the past decade the international environmental focus in the mining industry has moved from operational management, to the reduction of liability on mine closure. Mine closure guidelines are being developed internationally by nations (for example, SRK, 19982) and by large mining groups (for example, Rio Tinto, 19983). In South Africa the Department of Minerals and Energy (DME) is presently reviewing the Aide-Mémoire to bring it in line with international and local developments and a separate mine closure plan is being considered.

Jan 1, 2000

By N. Kornelius

In recent years there has been an increased focus on corporate governance matters worldwide. The duties and responsibilities of directors of companies have come under close scrutiny, with shareholders increasing their demands for greater responsibility and accountability. Media attention and pressure groups have also had their effect. Governmental actions have supported these demands and directors have witnessed sweeping legislative changes imposing more onerous duties and liabilities than formerly imposed upon them at common law and in terms of the Companies Act. At the same time, the power of regulatory bodies has been increased to enforce this legislation and make someone pay to remedy an alleged infringement. Breach of such duties may incur personal or criminal liability, or both. Environmental protection legislation has become a particularly prevalent feature in this regard, and the number and complexity of statutes concerning the environment have increased over the past few years. Directors of South African companies will be familiar with relevant acts such as the National Environmental Management Act 107 of 1998; Conservation of Agricultural Resources Act 43 of 1983;Hazardous Substances Act 15 of 1973, as well as the National Water Act 36 of 1998. Now the directors of mining companies are faced with the Mineral and Petroleum Resources Development Act 28 of 2002.

Jan 1, 2003

By W. Bryszewski

As a result of strategic analysis in respect of the needs for air quality management a new advanced and holistic approach to air quality management process was introduced in the North West Province (NWP) of South Africa. The process is based on the principle of co-operative management. It involves both active participation of all Interested and Affected Parties (I&AP) and the holistic approach to solving problems with the underlying principles of shared ownership and sustainable development. The process consists of the followings phases: ? Industrial process quantification ? Quantification of impacts ? Formulation of the required control measures ? Definitions of certificate conditions ? Implementation of an adequate compliance management system at company level ? Ongoing co-operative air quality and system management with the strategic objective of continuous improvements The system has been successfully introduced in the North Province and proved to be an effective management tool and aids assurance of sustained environmental ability to cope with the pressure of industrial developments. The benefits and effectiveness are discussed using Hernic Ferrochrome as an example. Hernic Ferrochrome is one of the first companies, which successfully implemented this system.

Jan 1, 2004

By N M. Vegter, C B. Kohler, E H. O Meyer

Zincor operates four Lurgi fluidised-bed roasters at its roast-leach-electrowin refinery in Springs, South Africa. In 2006, Zincor?s four roasters had reached ages ranging between 26 and 38 years, while the expected life of this type of roaster is generally 20 to 25 years. Based on its condition, Roaster 3 was the first to be rebuilt in 2006. Roaster 4 is being rebuilt in 2007 and the last two roasters will be rebuilt over the next few years as necessary. The main damage to Roaster 3 was caused by buckling of the roaster steel shell. This caused the freeboard and dome areas to shift, resulting in cracks in the dome brick lining and crumbling of the bricks lining the freeboard. The steel shell buckled due to the combined effects of too-high operating temperatures and corrosion caused by the following two main factors: ? Thicker external insulation was installed during a previous maintenance shut which resulted in and increased steel shell temperature and exacerbated the normal metal fatigue; ? SO2/SO3 containing gas that had permeated through the brick lining, passed through its dew point during frequent planned and unplanned shuts over the life of the roaster. This caused acid formation between the refractory brick lining and steel shell, resulting in corrosion of the shell. The initial plan was to replace only the damaged areas of Roaster 3, but upon dismantling more damage was found and the roaster was rebuilt from the tuyeres upwards. During the rebuild, the opportunity was taken to modify the design of some of the brickwork to extend its life and make future repairs easier. This paper discusses the mode of failure of Roaster 3 and the lessons learnt during its dismantling and rebuilding.

Jan 1, 2007

By L. A. Cornish, L. H. Chown, M. Matema, R. Süss, L. Glaner, A. Douglas

Mintek has been developing Pt-based alloys for high temperature applications in aggressive environments, for example, land-based turbine engines, to replace the currently used nickel-based superalloys (NBSAs). The Pt-based alloys have a similar structure to the NBSAs, and since Pt is more chemically inert and has a higher melting point, the Pt-based alloys can potentially be used at higher temperatures. The greater chemical inertness of the Pt-based alloys compared to the NBSAs means that coatings can be simpler, or perhaps not even used at all, depending on the environment. TEM work was done at NIMS, Japan, to investigate the changes in the microstructure o f Pt-Al and Pt-Al-Ir alloys at elevated temperatures using in-situheating up to1100°C. Initial casting trials showed that work needs to be done to optimise casting parameters before commercialisation can take place. Room temperature tensile tests were performed and results were variable mainly due to microstructural differences. The alloy hardnesses were in the order of 300-350HV with ultimate tensile strengths of ~800 MPa and elongations of less than 10%. These results are comparable to other alloys used at high temperatures, which is very encouraging. Keywords: platinum, super alloys, hardness, tensile

Jan 1, 2006

By G. S. Littlejohn

Following study of historical South African practice and a review of recent experience gained during the design, construction and testing of the high pressure plugs at the South Deep Water Barrier Project, this paper makes recommendations to improve practice. Initially, site investigation requirements are described with reference to geological, hydrogeological and seismic considerations, including site preparation and pre-grouting of the surrounding rock mass, if permeable. Structural and hydraulic aspects of plug design address topics such as residual permeability, aggressive mine water, plug materials, mortar strength and bleed. In situ thermocouples and piezometers are recommended to optimize the timing of plug tightening and monitor plug performance during service. Plug construction covers aggregate preparation, mortar quality control, plug tightening grouts, injection pressures, records and the overriding need for a method statement specification to control all aspects of plug construction. On completion of the plug, tests to establish surrounding rock stress regime, plug strength, and residual permeability are described to enable a comparison with original design assumptions. Monitoring and maintenance procedures are proposed to ensure satisfactory long-term performance of the plugs.

Jan 1, 2006

By G. A. Craig

The Moon, asteroids, and planets of the solar system represent the most distant caches of wealth that humanity has ever considered recovering. Yet, in addition to the potentially recoverable values represented there, harvesting off-Earth resources has a second, almost incalculable sustainable benefit in that they can be retrieved with absolutely no damage to Earth. Previous research mostly assessed the potential of asteroids and the Moon for mining purposes from a theoretical and scientific point of view. These studies investigated drawbacks that could be experienced in this type of operation, but no detailed economic evaluation that is meaningful for mining project management has been conducted and the parameters that are most likely to make an operation feasible are unknown. This paper provides a preliminary economic and sensitivity analysis of a possible off-Earth mining business extracting minerals from an existing asteroid.

Jan 1, 2014

By P. J. D. Lloyd

At first I read this paper with interest, which grew to fascination, and ended up with horror. Such reactions to a supposedly scientific contribution are rare, and I believe the coal mining community must be warned in the strongest possible terms against the recommendations that this paper makes. The paper purports to have assessed statistically two sets of data on methane concentrations recorded in the return air from Turkish longwalls. The first set of data, from their Table I, is reproduced in Table I below. The data have been rearranged in classes to indicate the underlying distribution. While there is only limited data (N=33), the distribution looks as if it could be the sum of two normal distributions with means around 0.5 and 0.8, or possibly a log-normal distribution. What is quite clear is that it is nota single normal distribution.

Jan 1, 2004

By M. A. Amarante

Beneficiation studies were conducted on a Portuguese feldspar ore, in order to obtain final products capable of being used in the ceramic industry. A simple scrubbing operation is enough to break the lumps in the feed. The ore deposit contains ca 35 x 106tonnesfrom which, by screening, three main products could be obtained. This paper focuses on the beneficiation of the 500/74 µm fraction, which constitutes about 27% of the ore, assaying 9.42% Al2O3,equivalent to approximately ca 46% feldspar, with a mean iron content of 0.29% iron oxides. Magnetic separation and froth flotation testwork was carried out, in order to decrease the iron contamination and increase the feldspar content. Magnetic separation alone decreased the iron content of the feed to values between 0.04 and 0.08% iron oxides with an average yield greater than 90%. Flotation with HF, provided a feldspar recovery of 45?46% with a concentrate assaying 17.6% Al2O3. The use of H2SO4, gave a recovery of 35?36% of feldspar concentrate, assaying 16.1% Al2O3. However, economic and environmental advantages of using sulphuric acid may compensate for the lower mass recovery. The iron content of0.12% iron oxides in these concentrates, could be reduced to 0.04?0.05%, by further magnetic separation.

Jan 1, 1997

By B. M. Nyombolo

Mintek has been involved in the development of bioleach technology for many years, initially for refractory gold extraction, and more recently also for base metals extraction. Mintek, in collaboration with its Australian technology partner (BacTech), is the technology provider for the Beaconsfield refractory gold bioleach plant. At present Mintek, BacTech and Peñoles are constructing a demonstration bioleach plant for copper-zinc concentrate treatment. Bioleach liquors produced in all applications have to be neutralized. In the copper-zinc case, neutralization is required for bleeding iron from the circuit and for adjusting the pH value ahead of solvent extraction. In the refractory gold bioleach circuit, neutralization is required for producing a stable iron-arsenic residue. Some of the challenges encountered in each of these neutralization applications are discussed, and examples of results obtained are presented.

Jan 1, 2000

By D. Pillay

Outsourcing? and ?sub-contracting? have become buzzwords in recent years, as SA industry becomes increasingly exposed to the global economy, and global competitiveness. In its effort to ?catch up? after years of relative isolation, there is a concerted effort to learn from global ?best practice?, in order for South African companies, and the SA economy, to become ?winners?. There seems nothing wrong with this approach at face value. Companies need to compete and be profitable if they are to remain in business. Failure will in the end mean bankruptcy, and the loss of jobs. However, if one interrogates the precise practices, and their implications for all concerned?not just shareholders and employers, but workers, communities, the environment, future generations, the national economy?then the picture can change dramatically. ?Best practice? for whom?

Jan 1, 1999

By P. M. Cole

An unprecedented expansion of the global zinc industry is currently under way. While most new projects and plant upgrades remain committed to traditional processing technologies, recent advances in zinc solvent extraction (SX) have created opportunities for new process routes for both primary and secondary materials. The first commercial plant to use zinc SX for the mainstream processing of a low-grade ore is under construction and promises to become one of the lowest cost zinc producers. Several other oxide and sulphide projects in various stages of feasibility are considering the inclusion of SX in their process flowsheet. Zinc SX has also proved advantageous in the reprocessing of secondary materials, particularly for the treatment of zinc residues and furnace dusts. This review focuses on recent installations and projects underdevelopment that feature zinc SZ as the key separation step.

Jan 1, 2002

By A. Feather

The Minataur? Process (Mintek Alternative Technology for Au Refining) is a novel route for the production of high-purity gold using solvent extraction. Following the successful demonstration of the process on a pilot-plant scale, a full-scale 24 t/a production plant has been commissioned at Harmony Gold Mine in Virginia, Free State. The commercial implementation of this process represents not only a significant advance in gold-refining technology, but may be instrumental in initiating important changes in the legislation regulating the marketing of gold in South Africa. Gold of either 99.99% or 99.999% purity can be produced from intermediate process products having a wide range of gold contents. The process comprises oxidative leaching of the solid feed, followed by selective solvent extraction of the gold from the leach liquor to reject impurities, and precipitation of high-purity gold powder. This paper outlines the process, presents selected results of two pilot-plant trials in which 5 kg/d of high-purity gold was produced from silver-refining anode slime and gold-electrowinning cathode sludge, and provides some details of the cost benefits.

Jan 1, 1997

Cokriging uses a sparsely sampled, but accurate and precise primary dataset, together with a more abundant secondary data-set, for example grades in a polymetallic orebody, containing both error and bias, to provide improved results compared to estimation with the primary data alone, as well as filtering the error and mitigating the effects of conditional bias. The method described here may also be applied in polymetallic orebodies and in other cases where the primary and secondary data could be collocated, and one of the data-sets need not be biased, unreliable, etc. An artificially created reference data-set of 512 lognormally distributed precious metal grades sampled at 25×25 m intervals constitutes the primary data-set. A secondary data-set on a 10×10 m grid comprising 3200 samples drawn from the reference data-set includes 30 per cent error and 1.5 multiplicative bias on each measurement. The primary and secondary non-collocated data-sets are statistically described and compared to the reference data-set. Variograms based on the primary data-set are modelled and used in the kriging of 10×10 m blocks using the 25×25 m and 50×50 m data grids for comparison against the results of the cokriged estimation. A linear model of coregionalization (LMC) is established using the primary and secondary data-sets and cokriging using both data-sets is shown to be a significant improvement over kriging with the primary data-set alone. The effects of the error and bias are filtered and removed during the cokriging estimation procedure. Thus cokriging using the more abundant secondary data, even though it contains error and bias, significantly improves the estimation of recoverable reserves.

Jan 1, 2014