Search Documents

By D. Boshoff

The ability of an explosive to break rock is influenced considerably by the extent of confinement in the blasthole. It is believed that confinement is improved by the use of adequate stemming. The aim of this paper is to present the results of the first and second stages of developing a stemming performance testing rig for small diameter boreholes. The rig was used to compare and contrast the performance of different designs of products. The results showed that different stemming products have differences in terms of their functionality, which can have a major impact on the efficiency of rock breaking. Two test procedures were used, one through the exclusive use of compressed air and the second using a purpose-built high pressure test rig with small quantities of explosives. Both tests were used to identify and evaluate the ability of various stemming products to resist the escape of explosive gas through the collar of a blasthole. An investigation was done to determine the types of stemming products most commonly used in South African underground hard rock mines, and these products were used during the tests. The first stage of tests using compressed air only did not prove adequate to predict with certainty the pressure behaviour in the borehole of a particular product under high pressure conditions. The purpose-built high pressure test rig also did not prove to be a very effective tool to test stemming products under high pressure conditions. The test rig incorporated only the effect of gas pressure on the stemming product, and excluded the effect of the shock wave. This study therefore proved that to take into account only the gas pressure generated in the blasthole is not sufficient to effectively test stemming product performance.

Jan 1, 2011

By K. S. Rao, R. P. Tiwari, V. K. Shrivastava

ABSRACT: In this paper numerical simulation of jointed block mass behaviour obtained in an experimental study has been presented. Singh et al. (2002) conducted extensive tests on the jointed model materials with several joint configurations. The results of this experimental study were used to validate the strength behaviour of numerical block mass model developed using professionally available software. This software basically contains different kinds of material models. From the results of numerical simulation the existence of strength anisotropy was observed. The strength anisotropy so obtained has been compared with the experimental values reported by Singh et al. (2002). The anisotropic curves in both cases are U-shaped with flat base. They show good agreement in sliding mode of failure zone in which inclination ß (= 90° - ?) of joint set-I lie between 20° to 40° for all cases of interlocking. ZUSAMMENFASSUNG: In dieser numerischen Papiersimulation des verbundenen Blockmasse Verhaltens, das in einer experimentellen Studie erhalten wird, ist dargestellt worden. Singh et al. (2002) leiteten umfangreiche Tests auf den verbundenen vorbildlichen Materialien mit einigen gemeinsamen Konfigurationen. Die Resultate dieser experimentellen Studie wurden verwendet, um das Stärke Verhalten des numerischen Blockmasse Modells zu validieren, das mit professionell vorhandener Software entwickelt wurde. Diese Software enthält im Allgemeinen unterschiedliche Arten der materiellen Modelle. Von den Resultaten der numerischen Simulation wurde das Bestehen von Stärke Anisotrophie beobachtet. Die Stärke Anisotrophie also erreicht ist mit den experimentellen Werten verglichen worden, die von Singh et al. (2002) berichtet werden. Die anisotropen Kurven in beiden Fällen sind mit flacher Unterseite u-förmig. Sie zeigen gute Vereinbarung in gleitender Erscheinungsform des Ausfalls Zone, in der Neigung ß (= 90° - ?) von der Verbindung stellenSie Lüge zwischen 20° auf 40° für alle Fälle vom Ineinandergreifen ein. RESUME: Dans cette simulation numérique de papier du comportement joint de la masse de bloc obtenu en étude expérimentale a été présenté. Singh et autres (2002) ont effectué les essais étendus sur les matériaux modèles joints avec plusieurs configurations communes. Les résultats de cette étude expérimentale ont été employés pour valider le comportement de résistance du modèle numérique de la masse de bloc développé en utilisant le logiciel professionnellement disponible. Ce logiciel contient fondamentalement différents genres de modèles matériels. Des résultats de la simulation numérique on a observé l'existence de l'anisotropie de force. L'anisotropie de force ainsi obtenu a été comparée aux valeurs expérimentales rapportées par Singh et autres (2002). Les courbes anisotropes dans les deux cas sont en U avec la base plate. Elles montrent la bonne concordance dans le mode coulissant de la zone d'échec en lequel la inclination ß (= 90° - ?) du joint placez-Je le mensonge entre 20° à 40° pour tous les cas d'enclencher.

Jan 1, 2003

A wide range of drill holes and process streams are sampled for resource estimation, grade control, and contractual purposes in the minerals industry. However, despite the availability of training courses, conferences and both national and international standards on correct sampling practices, it is still surprising how often little attention is given to ensuring that representative samples are collected for analysis. The reason for this is that the responsibility for sampling is often entrusted to personnel who do not appreciate the significance and importance of sampling, with cost being the main driving force rather than whether the sample is representative of the material from which it was extracted. This seriously undermines the precision and accuracy of the analyses subsequently generated and can render the analysis process a total waste of time and money and expose mining companies to serious, potential, financial losses. Company management needs to reverse this situation and ensure that sampling is given the attention it deserves to generate representative samples for analysis.

Jan 1, 2010

By L. Malmgren, A. Ansell

This paper deals with the influence from blast induced stress waves on the performance of shotcrete support in the Kiirunavaara mine. Time histories of stress waves from blasting were obtained from measurements during production blasts in the mine, followed by failure mapping. A finite element model, consisting of beam and spring elements, was used to calculate the shotcrete response to vibrations from blasting. The modelling approach was similar to that of a building during an earthquake, with accelerations measured in-situ used as loads. The analysis showed that the calculated adhesive stresses exceeded the strength in the interface between rock and shotcrete near to the blasted ring. It also indicated that tensile rock failure did occur. These types of failure will presumably result in ejection of joint defined rock blocks or rock slabs and will require a ductile support, such as fibre reinforced shotcrete. The predicted failure was confirmed by the mapping, which also showed that the zone of failed shotcrete was much larger in areas with plain shotcrete compared to areas with reinforced shotcrete. L’influence de l’onde de pression générée par les sautages à la mine de fer de Kiruna sur la performance du béton projeté est étudiée dans le présent article. Les ondes créées par les sautages ont été enregistrées et les domages résultants ont été cartographiés. La réponse du béton projeté aux vibrations de sautage est étudiée à l’aide d’un modèle d’éléments finis, constitué de poutres et de ressorts. L’approche est similaire à celle d’un immeuble subissant un tremblement de terre, avec les accélérations internes utilisées comme charges. L’analyse montre qu’à proximité des sautages, la contrainte adhésive dépasse la résistance de l’interface roche-béton. L’analyse confirme aussi l’existence de ruptures en tension. Ces types de rupture induisent probablement l’éjection des blocks définis par les structures du massif rocheux et requierent un support ductil, comme du béton projeté renforcé par exemple. Le type de rupture est confirmé par les observations de terrain, qui montrent aussi une extension plus importante des domages lorsque le béton projeté n’est pas renforcé. In diesem Konferenzbeitrag geht es um den Einfluss, der aus einer Sprengung hervorgerufenen Schwingungswellen auf die Ausführung der Spritzbetonverstärkung in dem Kiirunavaara Bergwerk. Die Aufzeichnungen der Schwingungswellen von Sprengungen gemäß einer Fehlerkartierung beziehen sich auf Messungen, die während der Sprengungen durchgeführt wurden. Ein Finite Elemente Modell, bestehend aus Stab- und Federelementen, wurde für die Berechnung der Spritzbetondeformation in Bezug auf die Schwingungen aus Sprengungen angewendet. Die Modellierungsmethode war ähnlich der eines Gebäudes während eines Erdbebens anhand der gemessenen Beschleunigungen vor Ort, die als Lasten benutzt wurden. Die Untersuchung hat gezeigt, dass die berechnete Haftspannung größer war als die Festigkeit in der Verbindung zwischen Gestein und Spritzbeton in der Nähe des Sprengungscentrums. Die Analyse hat gezeigt, dass die Zugfestigkeit des Gesteins versagte. Diese Arten von Versagen werden als Folge der Herausnahme von Gesteinsbrocken oder Gesteinsplatten erklärt und benötigen eine faserverstärkte Spritzbeton. Das vorausgesagte Versagen bestätigte sich beim Kartieren, welches auch zeigte, dass die Zone des versagenden Spritzbetons in Bereichen mit unverstärktem Spritzbeton viel größer war als in Bereichen mit armierten Spritzbeton.

Jan 1, 2003

Quantitative seismology is an important tool for investigating mineinduced seismicity and the quantification of the seismic rock mass response. The spatio-temporal interpretation of seismic data within an ever-changing three-dimensional mining environment provides some challenges to the interpretation of the rock mass response. A grid-based approach for the interpretation of spatial variation of the rock mass response provides some benefits compared with approaches based on spatial filters. This paper discusses a grid-based interpretation of seismic data. The basic methods employed in the evaluation of the parameter values through space are discussed and examples of applications to different mine sites given.

Jan 1, 2014

By J. M. Ortiz

Grade control and short-term planning are usually based on the samples obtained from blastholes. These samples may carry a large sampling and sample preparation error. At El Tesoro copper mine in northern Chile, an advance drilling grid is used for short-term planning and grade control. These drill holes are sampled well in advance, and a short-term model that incorporates several variables and sophisticated estimation methods can be prepared for decisionmaking. An additional advantage of the advance drilling samples is that reverse circulation can be used instead of conventional down-the-hole equipment, and a very careful sampling and sample preparation process can be implemented, reducing the total sampling error. Advance drilling can be performed on a wider grid than blasthole drilling, hence the decision about the grid requires assessing the economic benefit of different sampling grids. Furthermore, this process allows the cost of poor sampling and the effect of different estimation procedures to be quantified. We demonstrate the optimization of the drilling grid for short-term planning and grade control at El Tesoro mine by means of the economic evaluation of the performance of different drilling grids, with different drilling techniques (which differ in the sampling error). The methodology is based on creating dense (exhaustive) geostatistical simulations of the grade distribution over a volume defined for a production period in respect of the geological model, and assuming each simulation as the true grade distribution. Then, samples are obtained from the exhaustive simulations at a spacing similar to the advance grid to be evaluated, and a sampling error is added. The short-term estimation procedures used on the mine are applied to determine the destination of each block and the profit obtained. This profit can be compared with the maximum profit (unachievable) and with the profit under different sampling errors and grids. The results show that the current 8 x 8 m drilling grid is appropriate and by reducing the sampling error, misclassification is also reduced, leading to an increase in profit of about US$ 5 million in 4 years.

Jan 1, 2012

By A. V. Roschin, N. V. Malkov, V. N. Karnoukhov, V. E. Roschin

Reduction interactions in solid phases are widespread and occur in most complex metallurgical processes. Among these processes, reactions between oxides and carbon have a special importance. The authors conducted experiments for comparison of reduction by different reducing agents of impregnated chromite ores, in which grains of the reducible chromite spinel are isolated from direct contact with the reducing agent by layers of non-ore material. The results of the experiments have revealed that the beginning of reduction is preceded by thermal and impurity order-disorder transformation of the oxide lattice whilst the transformation of the oxide lattice into the metal lattice takes place as a result of removal of oxygen anions from the zone of metal germ nucleation. Since anions are charge carriers, increase of their mobility can be monitored by changes in electrical conductivity of oxides. Respective measurements of electrical resistance of ores of different metals and a number of pure refractory oxides under heating have indicated that the beginning of reduction coincides with the time of drastic (tens of thousands times) increase of conductivity of the oxides. Besides, the temperature of the beginning of carbon-thermal reduction is in line with the Tammann temperature, i.e. the temperature of transition from the predominantly surface diffusion to volume diffusion. Segregation of metals from the oxide lattice occurs as a result of merging of anion vacancies with defect electrons on defects of the oxide lattice. The transformation of the oxide lattice into the metal lattice requires a certain concentration of anion vacancies and inflow of electrons from the reducing agent to the site of metal segregation. Such inflow has no difficulties due to the mixed anion-electron nature of high-temperature conductivity of oxides. Thus, the reduction is not determined by oxygen diffusion, it is determined by oxygen vacancies diffusion whose speed exceeds the speed of oxygen diffusion by orders of magnitude. This determines that the kinetics of reduction considerably exceeds the kinetics of oxidation at similar temperatures since oxidation proceeds by means of mass transfer of oxygen through the layer of the generated oxide.

Jan 1, 2004

By M. B. Shongwe

Pt-based alloys are being developed for high-temperature applications with the aim of replacing some of the currently used Ni-based superalloys (NBSAs) in the highest temperature applications. The Pt-based alloys have a similar structure to the NBSAs, and since Pt is more chemically inert than nickel and has a higher melting point, they can potentially be used at higher temperatures, up to 1300°C, and in more aggressive environments. Several experimental Pt-based alloys were studied at Mintek, and an optimum composition was found to be Pt84:Ahi:Ru2:Cr3 (at.%). On the basis of hardness and microstructure, a later study identified a new optimum: Ptr8:A111:Ru5:Cr6 (at.%). There are at least two Pt3A1 allotropes, and the high-temperature cubic structure has better properties than the lower temperature tetragonal form, and so needs to be stabilized. This work describes the latest results obtained in transmission electron microscopy (TEM) studies of the quaternary Pt-based superalloys. These results are both interesting and important, because the samples have a higher precipitate density compared to those from earlier work. The precipitate morphology is mainly cubic, with minor areas having irregular-shaped precipitates. The high volume fraction of the precipitates is a major breakthrough, since the objective of this work is to improve the alloys. A prior disadvantage was that the proportion of the precipitates was too low in samples before this work, especially compared with the work from Germany on Pt-Al-Cr-Ni¬-based alloys as well as the NBSAs. TEM -Pt3A1 diffraction patterns were studied, and for each diffraction pattern, many possible lattice point combinations were tried, with the angle between the lattice spots as well as interplanar spacings being calculated for each phase (cubic or tetragonal) to match the measured results. An overall analysis of the diffraction results indicates that the cubic phase fitted the experimental lattice points with much lower errors compared to the tetragonal phase. Thus, with the close match achieved with the cubic structure, the structure of -Pt3A1 precipitates is likely to be cubic. X-ray diffraction has been carried out on selected samples, and the results confirmed the presence of cubic -Pt3A1 and (Pt). Different X¬ray diffractometers were used to further verify the results, and the results were also compared with those from TEM.

Jan 1, 2012

By M. G. Senyur

This study aims at investigating the structural characteristics of backfilling material. In this regard, spatial arrangement of solid particles and associated voids in a unit mass of coal mine refuse as backfilling material were tested. The materials were produced from coal mine refuse of Zonguldak Colliery, Turkey. The experimental procedures were developed to determine their void ratio (or its equivalent porosity), bulk density and the shape properties of constituent particles. The orientation fabric and the co-ordination number were the other two fabric elements determined. The filling materials were sieved and their particle size distributions were found. The results obtained by experiments were related to the particle size distribution parameters, namely, the coefficient of uniformity and the effective size. It was concluded that mean value of void ratio is correlated with coefficient of uniformity. The standard deviation of porosity as an index of fabric heterogeneity is clearly correlated to effective size. By an original experiment, the frequency distribution of coordination number was observed as binomial in uniformly graded materials. Also, the co-ordination numbers of test mixtures were calculated by the Marsal method and results obtained showed a good correlation between the minimum particle size and number of contacts per unit area.

Jan 1, 1998

Assuming that a gold ore has been effectively ground to ensure maximum economic liberation of gold, the circuits that will have the most effect on the successful operation of a gold plant will be that of the leaching and carbon-in-pulp circuit (CIP). The reagent and utilities operating costs associated with leaching, adsorption, elution and regeneration would typically make up some 15% of total operating cost, whilst the capital costs associated with these areas is about 16% of the total. Although not largest (capital and operating costs associated with comminution are generally dominant) these items represent a significant proportion of capital and operating cost. Much more importantly, these plant areas represent the primary gold recovery process and their technical and operational efficiencies will have a significant impact on overall plant efficiency. The objective during process design of these sections is thus to develop a design which provides maximum technical and economic efficiency and which is robust to potential changes in ore throughput, mineralogical characteristics and head-grade. Experience has shown that, particularly for longer life and higher-grade projects typical of the South African underground gold mining industry, small changes in recovery and efficiency have a significant value over the life of the project.

Jan 1, 1999

By K. Shin

Determining the anisotropy of rocks has in the past been difficult and rarely attempted in engineering practice. Here we have developed a new practical methodology for measuring orthotropic anisotropy that requires only one hollow cylinder specimen to determine the anisotropy of a set, even when the directions of the anisotropic axes are unknown. Autrefois, la détermination de l’anisotropie des roches était difficile et elle a été rarement essayée dans la pratique de l’ingénierie. Voilà c’est nous qui avons mis au point une nouvelle méthodologie pratique pour mesurer le coefficient de conductibilité thermique de l’anisotropie qui exige un seul spécimen du cylindre creux afin de déterminer l’anisotropie d’une série, même si les directions des axes anisotropiques sont inconnues. Früher war die Bestimmung der Anisotropie von Gesteinen ein schwieriges Verfahren, das in der technologischen Praxis nur selten in Angriff genommen wurde. Wir haben hier eine neue praktische Methodik zur Messung der orthotropen Anisotropie entwickelt, bei der nur ein Hohlzylinder an Gesteinsproben benötigt wird, um die Anisotropie einer Reihe von Steinen zu bestimmen, selbst wenn die Richtungen der Anisotropieachsen unbekannt sind.

Jan 1, 2003

By J. W. Klokow, K. L. Riemer, R. I. L. Ferreira

As a result of the increased depth of mining in the South African gold mining industry mining induced seismicity is a severe problem. One of the strategies within the industry to contain the problem is to incorporate a system of regularly spaced stabilising pillars into mine layouts. At the Driefontein Gold Mine a system of closely spaced dip pillars is used to contain seismic energy emissions. Comparisons of seismic data for several mining clusters initially indicated a possible measure of success in the containment and occurrence of larger events. A detailed analysis of data over a 5-year period since the start of mining however, has revealed a delayed seismic response to the increasing strike spans. Significant changes marked by an increase in certain seismic variables have been observed at mining spans of between 100 to 120 meters and could be of significance to pillar spacing in the design of deep level mining layouts. La sismicité occasionnée par l’exploitation minière est un problème grave dans les mines profondes de l’industrie minière aurifère en Afrique du Sud. Une des stratégies utilisées dans l’industrie a été de maîtriser le problème en incorporant un système de piliers de stabilisation régulièrement espacés dans la disposition des mines. A la Driefontein Gold Mine, un système de piliers de pendage proches les uns des autres est utilisé pour contenir les émissions d’énergie sismique. Au début, des comparaisons de donnés sismiques pour plusieurs groupes d’extraction ont indiqué un succès possible dans la limitation et l’occurrence d’évènements sismiques. Cependant, une analyse détaillée des données sur une période de 5 années a révélé un délai entre la progression de l’extraction et une réponse sismique accrue. Des changements considérables dans les variables sismiques ont été observés dans des intervalles d’extraction entre 100 et 120 mètres, ce qui pourrait être significatif pour l’espacement des piliers dans la conception de la disposition des mines de fond. Resultierend aus den zunehmenden Tiefen des Bergbaus in der südafrikanischer Goldbergbauindustrie stellt sich die vom Bergbau hervorgerufene Seismizität als bedrohliches Problem dar. Es war eine der Strategien innerhalb der Industrie, das Problem dadurch einzudämmen, daß regelmäßig plazierte Stabilisierungspfeiler in den Bergbaulayouts inkorporiert wurden. In der Driefontein Gold Mine wird ein System von knapp aneinandergesetzten im Abfallbereich befindliche Pfeiler benutzt, um seismische Energieemissionen einzudämmen. Vergleiche der seismischen Daten für mehrere Bergbaugruppen zeigten anfangs ein mögliches Maß von Erfolg in der Eindämmung und im Auftreten von größeren Fällen an. Eine ausführliche Analyse von Daten über einen 5jährigen Zeitraum hat jedoch ergeben, daß eine Verzögerung zwischen der Progression des Bergbaus und einer erhöhten seismischen Reaktion besteht. Bedeutende Änderungen in den seismischen Variablen wurden an Bergbauspannen von 100 bis 120 Metern beobachtet und könnten für Abstandsbemessung von Pfeilern im Design des Tiefbergbaulayouts von Bedeutung sein.

Jan 1, 2003

Following a short review of selected literature, a back analysis of stress measurements of stress regeneration in a closed mini-longwall is shown. The agreement is good, lending confidence to the parameters used in the proposed numerical model. Foundation yielding was modelled in the absence of total stope closure. A ?Prandtl? wedge was formed, coinciding with the yield point of the pillar/foundation system. Some theoretical work is used as a starting point for the formulation of a new design methodology for strike or dip stabilizing pillar/foundation systems in deep level goldmines. The existing guideline for the stability of foundations (APS< 2.5UCS) is critically examined. Finally, the advantages of the new approach, and the work required to substantiate the proposed new design methodology, are outlined.

Jan 1, 1998

By Van Sint JanM., M. Prudencio

ABSTRACT We report the results of a model-testing program to evaluate the strength characteristics of non-persistent joints. We describe the conditions under which new tensile cracks generate and propagate to connect existing joints so that the rock mass becomes fractured into several blocks, leading to a low strength. The strength of some models was equal to that along a single joint through the full sample length. In models with two joint sets, failure took place along a composite plane, partly sliding along a discontinuous joint and shearing through the intervening intact block of rock, or else by rotation and sliding of the blocks. This last failure mode could also lead to very low model strength. ZUSAMMENFASSUNG Dieser Bericht beschreibt die Ergebnisse von Versuchen mit Modellfelsmassen um den Einfluâ von unterbrochenen Rissen in ihrer Widerstandsfähigkeit zu untersuchen. Es werden die Umstände beschrieben unter denen neue Zugrisse entstehen, sich verbreiten, sich mit bestehenden Rissen verbinden und die Felsmasse in mehrere Felsblöcke zerlegen und zu einer kleinen Widerstandsfestigkeit führen. Der Widerstand einiger Versuchskörper entsprach der Festigkeit eines Risses der die ganze Länge des Versuchskörpers überquert.Versuchkörper mit zwei Rißfamilien versagten unter einer zusammegesetzten Ebene, zum Teil mit Verschiebungen nach unterbrochenen Rißebenen die sich durch Schnittversagen intakter Felsblöcke verbinden, und zum Teil durch Drehungen und Verschiebungen einzelner Felsblöcke. Die letzte Versagunsart kann zu einer stark verminderten Widerstansfähigkeit führen. RÉSUMÉ Nous présentons les résultats de quelques essais fait sur des modèles évaluant les caractéristiques de résistance des fractures discontinues. Nous décrivons les conditions sous lesquelles des nouvelles fissures de traction peuvent s’engendrer et se propager pour faire la connection avec des fractures existantes, de façon que le rocher se fracture en plusieurs blocs, menant à une résistance réduite. La résistance de quelques modèles fut égale a celle d’une fracture traversant toute la longueur du modèle. Pour les modèles ayant deux ensembles de fractures, la rupture a eu lieu sur une surface mixte, causée d’une part, par le glissement sur une fracture discontinue et d’autre part, par la rupture à travers le pont de matériel intact; ou bien par rotation et glissement des blocs. Cette dernière façon de rupture peut aussi aboutir à une très faible résistance des modèles.

Jan 1, 2003

By T. A. Muhlare

The use of electrolyte additives to smoothen cathode deposits during copper deposition is practised worldwide. These additives absorb on the cathode surface and take part in the electrochemical crystallization process. However, these additives also affect the quality of the cathodes when they are inadequately controlled. Electrolyte additives used by Palabora are glue, thiourea, Avitone and chloride. Their effects were determined on cathode quality, the size of the current density region that gives the desired compact morphology, and current efficiency. This was done in a small-scale cell. Small cells have different hydrodynamics from industrial-scale cells, which makes it difficult to simulate the operation of industrial cells in a laboratory. The approach used here was to use a rotating cylinder cathode to attain controlled hydrodynamics. The rotation speed was chosen to give a diffusion layer thickness that is similar to that of an industrial-scale cell. It was shown that even fairly small changes in the additive levels can significantly affect the cathode morphology, and the current density range over which this morphology can be obtained. Keywords Copper, electrorefining, glue, thiourea, avitone and chloride.

Jan 1, 2011

By W. U. Reimold, R. Armstrong, R. G. Charlesworth

For many years rockbursts have plagued the mining industry. Although much research has gone into studying this phenomenon only a small proportion of it has been on the actual source mechanism. A study was recently carried out to compliment the previous work done on the micro-structure of these features and to compare it to the micro-structures seen on shatter cones, from meteorite impacts. Both optical and electron-microscopy were used during the study. Samples were collected from rockburst sites by the CSIR Miningtek Rockburst Investigation Unit, and from the collar of the Vredefort Impact Crater. In the optical-microscopy study, the pinnate fractures observed in previous studies were seen in the shatter cones, through all the material. In the rockburst samples, the fractures were observed only in the quartz grains. Quartz micro-crystals were present in the rockburst samples and appeared to be the product of comminution rather than crystallisation. Cataclasite was present on rockburst and shatter cone fracture surfaces. The observations of the shatter cone surfaces with the scanning electron microscope are in agreement with previous work, including the observed presence of melt features, spherules and spheroidal material. The deformation in the rockburst samples is concentrated in the quartz grains, highly complicated with brittle features like sub-conchoidal structures and step structures present. A quartz spherule was identified on one rockburst sample and rhombic-dodecahedra type micro-crystals were present and seen fracturing off quartz grains. It is clear that the rockburst and shatter cone fracture surfaces are quite different; the shatter cone deformation is equally distributed across the sample and involves plastic-deformation, while the deformation in the rockburst material is concentrated in the quartz grains and, with the exception of spherule formation, is brittle. This study agreed with the current explanation for the formation of the rhombic-dodecahedra, and disproved the possibility of it being coesite or fine-grained meta-chert. Although there is no definite evidence of the mechanism of formation of the spherule, it is believed to be the product of vaporization and condensation, and the presence of this material indicates the extreme conditions under which this event occurred.

Jan 1, 2003

By Q. C. Reynolds

Keywords: Pyrometallurgy, plant, photography, GIS, satellite images, Google Earth Google Earth is a piece of software able to display an interactive three-dimensional map of the world, combining aerial and satellite photography with maps, terrain, and user-generated geographical information systems (GIS). Many structural features of the planet, both natural and man-made, are of great interest to the mining and metallurgy field, and in this paper a study is made of the current state of the art of data accessible by Google Earth.

Jan 1, 2006

By K. -C. Han, S. -Y. Kim

This study was carried out in a bid to survey Ganboke gold mine in Pala, Mayo-Kebbi Province, southwestern Chad. The Ganboke mine is now being prepared for investigation and development, and the research sought to perform rock properties tests of relevant rocks through its geological survey, rock mass evaluation, and in-situ and laboratory tests and analyze the stability by the means of limit equilibrium method, thereby suggest appropriate methods to design the pit slope and individual benches in Ganboke mine. Targenting GS1-GS1&apos; section with the depth of 180 m and GS2-GS2&apos; section with the depth of 150 m in the survey area, we set the height of the bench at 10 m and 15 m, and the angle of bench at 60o and 70o, respectively, and then reviewed the stability for dried condition and saturated condition. The result of examination indicated that it would be appropriate to set the bench height at 10m and the bench angle at 60o in developing the mine slopes concerned. Cette étude est réalisé dans le but de faire des recherches sur Ganboke mine d&apos;or dans Pala, Mayo-Kebbi Provence, Tchad sud-ouest. La Ganboke mine est actuellement en train de étre disposé à la investigation et le développement, et la recherche a cherché à accomplir les tests de la propriétè des roches par l&apos;intermédiaire de la étude géologique, la évaluation de la masse rocheuse, et in-situ et les tests de laboratoire et à faire l&apos;analyse de la stabilité au moyen de la méthode d&apos;équilibre limite, de ce fait à proposer le methodes propres à faire le plan de la pente et les gradins individuels dans la Ganboke mine. Concernant la section de GS1-GS1&apos; avec la profondeur de 180 m et la section de GS2-GS2&apos; avec la profondeur de 150 m dans l&apos;aire d&apos;étude, nous mîmes l&apos;hauteur du gradin à 10 m et 15 m, et l&apos;angle du gradin à 60o and 70o, respectivement, et alors nous avon reconsidéré la stabilité pour la condition sèche et la condition saturé. Le résultat d&apos;examen a indiqué que il pourrait être propre de mettre l&apos;hauteur du gradin à 10m et l&apos;angle du gradin à 60o en développant les pentes de la mine concerné. Diese Forschung wurde um das Gold Bergwerk zu überschauen in Pala, Mayo-Kebbi Provinz, der Südwesten Chad ausgeführen. Das Ganboke Bergwerk ist jetzt zur Erforschung und Entwicklung vorgebereiten worden, und die Forschung suchte zu ausführen die Prüfungen der Felseigenschaft durch geologischen Überblick, Felsmassewertbestimmung, und In-situ und Lavorversuch auf, und analysieren die Stabilität mittelst der Grenzegleichgewichtsmethode, da-durch schlug die angemes-sen Methoden zu entwerfen die Böschungen und die einzelnen Bänke im Ganboke Bergwerk vor. Für den Abschnitt GS1-GS1&apos; mit der Tiefe von 180 m und GS2-GS2&apos; mit der Tiefe von 150 m in der Überblickfläche, wir setzten die Bankhöhe an 10 m und 15 m, und das Bankwinkel an 60o und 70o, beziehungsweise, und dann zurückblickten die Stabilität für die getrockneten Bedingungen und die gesättigten Bedingungen. Das Ergebnis der Untersuchung anzeigte daß es würde angemessen sein zu setzen die Bqnkhöhe an 10m und das Bankwinkel an 60o in der Entwickelungen vom Bergwerk be-teiligt.

Jan 1, 2003

By H. M. Chikashi

Keywords: Pyrometallurgy, furnace, bath agitation, regression analysis, entrainment This paper presents the results of linear regression analysis of the influence that each component of slag has on the losses of copper in slag-cleaning-furnace slag. Data used for the analysis are actual plant data collected over the past two years of operation. Facts obtained from the study will be helpful for smelter management to control these components in the flash smelting furnace feed and slag, to levels which will enable better control of copper in slag, and smoother operation of the KCM slag-cleaning furnace.

Jan 1, 2011

By C. G. Anderson

"As demand for copper and precious metals continues to grow, the need to develop new supplies increases. In the imminent future, the new large global ore bodies are more complex, with enargite, tennantite and tetrahedrite as the abundant contained mineralogy. These resources also contain considerable gold and silver. As such, direct treatment by conventional smelting is prohibitive due to the potential environmental impacts and copper quality issues. This paper outlines the effective application and associated economics of industrially proven Alkaline Sulfide Leaching (ASL) hydrometallurgical technology to an enargite concentrate for selective removal and recovery of arsenic, antimony, gold and silver, leaving a clean high-grade copper concentrate. The fundamentals behind the technology are described, along with those of hydrometallurgical arsenic fixation and stabilization. Flowsheets and unit operations are elucidated, along with an in-depth economic analysis. INTRODUCTION Hydrometallurgical methods can be employed for treatment of gold-, arsenic-, antimony-, tin- and mercury-containing materials, concentrates and ores, as well as complex ones containing any number of metals (Conner & Anderson, 2013). The alkaline sulfide leaching (ASL) system is one of these. It is essentially a mixture of sodium sulfide and sodium hydroxide with other meta-stable alkaline species as required. This is a unique hydrometallurgical system beause it is a very selective lixiviant for the distinct leaching of tin, gold, antimony, arsenic, tellurium, silver and mercury (Anderson, 2000, 2001a, 2001b, 2002, 2003, 2012, 2014; Anderson & Twidwell, 2008a, 2008b, 2010; Anderson et al., 2004, 2005; Glazkov & Tseft, 1961; Gnatyshenko & Polyvyanni, 1961; Nadkarni et al., 1975; Nadkarni & Kusik, 1988; Polyvyanni, 1963). Worldwide, ASL technology has been employed industrially in the former CIS, China and the United States for the production of antimony (Anderson et al., 1992, 1994; Anderson & Krys, 1993; Holmes, 1944; Kaloc, 1967; Nordwick & Anderson, 1993; van Stein, 1971)."

Jan 1, 2015