Search Documents

By R. Pot

"IntroductionTHE PURPOSE of this paper is to discuss briefly the main logging and testing devices presently at our disposal, to point out some of their limitations, and to suggest possible improvements of the techniques.Some of the more important devices .are those that are used in:(1) Coring(2) Formation testing(3) Electric well logging(4) Radioactive well logging(5) Measuring of bottom hole pressures(6) Sampling of reservoir fluidsThe first four of these procedures are concerned with the well while it is in the process of drilling. The last two are carried out as soon as possible after a well has been brought into production and .at intervals during its life. My remarks will be concerned mostly with certain aspects of formation testing. The reservoir engineer is dependent on the information derived from these operations in order to obtain a clear picture of the conditions in a reservoir and to enable him to assess and forecast its future behaviour.Since any calculation is no better than the data on which it is based, not enough emphasis can be placed on the necessity for the testing and logging equipment to be of the highest quality and for the analysis of the results obtained to be thorough."

Jan 1, 1952

By E. W. Coderre, R. C. Baxter

"This paper describes the townsite of Wabush and the two railways operated by Wabush Mines for the loading and unloading of iron ore concentrate. The town of Wabush is located approximately 200 air miles north of Sept-Iles, Quebec and is in the Province of Newfoundland and Labrador. Construction of the town-site began in 1961 to provide housing accommodation for the construction force and permanent employees in the mining and milling operations located 4 miles away. Wabush Mines operates two short railway lines in loading and unloading concentrate between the concentrator, located at Wabush, and the pellet plant at Pointe Noire, Quebec. Both of these railways connect with the main line of the Quebec North Shore and Labrador Railway and provide a shuttle service between the two phases of the operation."

Jan 1, 1969

By C. M. Acuna, M. Sherrington

In high temperature processes thermodynamic equilibrium is assumed and therefore chemical potential of elements, among the condensed phases, have to be the same. In such situation impurities distribute accordingly and their fractional distributions are affected by the masses of the coexisting phases. It has been claimed Teniente Converters perform quite well for smelting high impurity concentrates, especially in respect to volatilization and/or slagging. Production of high matte grade near white metal composition, requiring moderate oxygen enrichment in the process air, results in a huge mass of gas and therefore a high fraction of impurities report to it. Similarly, by recycling different sources of slag, flue dust or other materials, the mass of the final slag is increased and so do the masses of impurities reporting to the slag. Nevertheless, above a certain level the recycling of smelter byproducts is no longer feasible and the cycle has to be halted, unless higher impurity mattes are accepted. Although the process might be continued during converting and refining, lengthy and expensive measures have to be taken if suitable anode copper for electrolytic refining is to be achieved. In the present study samples of high arsenic matte grade and slag were obtained on a pilot scale. The matte samples, on the order 75%Cu, were equilibrated with slag at varying ratios in magnesia crucibles under CO/C02 atmospheres at 1523 K. After 24 hours equilibrium matte and slag were rapidly solidified and analyzed by copper, sulfur, iron and arsenic. Furthermore, industrial samples of matte and slag, in the order 75%Cu at 1523 K, were obtained via a special quenching sampling device to determine the association of copper and suspension of matte and copper in slag. Based on the results, the distribution coefficient of arsenic between slag and matte was evaluated along with copper species in slag and the fractional distribution of arsenic, in the coexisting phases, was determined as a function of the ratio mass of slag to mass of matte.

Jan 1, 2007

By J. W. Matousek

"Computer modeling of smelting processes requires internally consistent equations for calculating the compositions of mattes and slags. That is, the sum of the calculated assays must total 100%. One set of equations that satisfies this requirement for copper produced under oxidizing conditions (pSO2>one atmosphere pressure) is given by the following:%[Fe] = 62.0 – 0.775%[Cu]%[S] = 28.0 – 0.00125%[Cu]2%[O] = 10.0 – 0.225%[Cu] + 0.00125 %[Cu]2Mattes containing nickel in appreciable quantities do not have the defined “white metal” end point of approximately 80 percent copper and 20 percent sulphur that is found in the copper system during the converting process. The above equations, however, are readily extended to nickel and nickel/copper mattes for any desired end product composition."

Jan 1, 1996

By D. L. Cramp

The Direct-Connected Electric Hoist In the latter part of 1931 a new electric hoist was installed at the Lake Shore mine. A number of interesting features were incorporated in this machine, which is the first direct-connected, direct-current-operated hoist to be placed in service in the Kirkland Lake district. Many factors requiring care and study enter into the selection of hoisting-engine drive. In this instance, conditions warranted the selection of the generator voltage control system (Ward-Leonard), utilizing a direct-current driving motor and a separate motor generator unit. It was further deter-mined that additional economies could be secured by the selection of a motor generator unit with a flywheel, and consequently the Ilgner-Ward Leonard flywheel set was adopted. Some of the advantages of this system are: 1) Greater accuracy of control, resulting in increased flexibility in hand-ling with increased precision and safety; especially desirable in large, important installations where the rope-speed is high or where frequent shifting is necessary. (2) Reduced energy consumption. (3) Feasibility of load equalization, without which, in some cases, the power system would be unable to carry the fluctuating load imposed on it by the operation of the hoist. ( 4) Elimination of reduction gearing in the construction of the hoist. The hoist is located on the surface and is used for skip operation at the main shaft, hoisting ore from a present maximum depth of 4,200 feet.

Jan 1, 1933

In this study, flotation of fine galena, chalcopyrite and pyrite was performed after grinding with different extent of oxidation-reduction condition adjusted by grinding media. Sodium dithionite and iron ions were added in mill to simulate pulp potentials and iron oxidation species produced by grinding media, respectively. The types and quantities of the metal oxidation species on mineral surfaces were determined by EDTA extractions, while the surface electrical properties of minerals and interaction of different types of metal oxidation species were studied by zeta potential measurements. It was found that the nature and concentration of the absorbed metal oxidation species were dependent on oxidation atmosphere controlled by the iron amount of grinding media. These species interacted with each other and had an important role in determining flotation of fine galena and chalcopyrite as well as activation of fine pyrite by lead and copper.

Jan 1, 2006

By John R. Sullivan, Real Daigneault, Mathieu Piché, Jayanta Guha, Gilles Bouchard

"RESUMELa stratigraphie du camp minier de Matagami se résume a la présence de deux groupes volcaniques: le Groupe du Lac Watson et le Groupe de Wabassee qui le surmonte. Les gisements de sulfures massifs volcanogènes sont situés au sommet du Groupe du Lac Watson. Ces roches sont déformées par l'anticlinal de Galinée dont l'axe, orienté E-W, plonge vers l'ouest. Le cœur de cette structure est occupé par le Complexe de la Rivière Bell.Les roches volcaniques du flanc sud de l'anticlinal sont peu déformées et pendent à 45° vers le sud. Les gites qui s'y trouvent présentent la morphologie typique des gisements de sulfures massifs volcanogènes. Ceux-ci se situent le long d'un horizon repère cherteux et sulfure, appelé ""Tuffite Clef', et leurs cheminées d'altération rejoignent, en profondeur, une zone d'altération stratiforme d'étendue régionale.Les roches du flanc nord ont été transposées tectoniquement en écailles chevauchantes, de dimension kilométrique, a l'intérieur d'un couloir de failles anastomosées d'orientation est-ouest. A l'intérieur: le ce couloir, les gites de sulfures sont déformes et sépares de leur héminée d'altération sous-jacente par des failles.Les gites de sulfures situes sur les deux flancs de l'anticlinal de 'Galinée se seraient mis en place dans un mime environnement volcanique. Leur position stratigraphique est identique puisqu' ils se 'rouvent au sommet de la rhyolite porphyrique du Groupe du Lac Watson. lis se seraient constitués au cours d'une pose volcanique recédant 1'éruption du basalte du Groupe de Wabassee. Le Complexe de la Rivière Bell est perçu comme la source de chaleur responsable de la circulation des fluides hydrothermaux qui sont à ""origine des gisements de sulfures massifs volcanogènes."

Jan 1, 1990

By M. Romana

"RMR geomechanics classification is being used all over the World as a useful tool for tunnel predesign and construction. Bieniawski (1989) provided guidelines for tunnel excavation and support, according RMR numerical values; guidelines which are now included in almost all tunnelling books, regulations, and Internet portals. But in the last 25 years tunnelling techniques have changed and some of the guidelines have become obsolete.. The conditions of tunnels for the 1989 guidelines application were: horseshoe shape; 10 m width; vertical stress < 25MPa; construction by drilling and blasting. Actually a substantial number of tunnels are mechanically excavated. The tunnel themselves are now bigger: a span of 14 m. is very common for transportation tunnels. The guidelines included the following concepts: excavation method, rock bolts (20 mm diameter, fully grouted), shotcrete, steel sets. There is an increasing gap between the 1989 guidelines and the practice: in many tunnels different to-the-case excavation and support requirements are established. Bieniawski himself has published a paper (Lowson & Bieniawski, 2013) with different guidelines based in Lowson’s practice, with no explanations and/or justification.In this paper a new set of RMR tunnelling guidelines is proposed taking account of the actual industry conditions, and increased safety regulations. The 5 classes’ limit RMR:values (80,60,40,20) are no more useful actually: Values of RMR (70, 50, 30) are used in practice to define quite different tunnelling techniques. Consequently a 10 subclasses system is proposed. Each subclass covers a span of 10 RMR points. As the number of mechanically excavated tunnels has increased a new correction factor is necessary, according the excavation method.The proposed 2014 RMR guidelines are for tunnels 10 to 14 meters wide, the world practice for new roads/railways tunnels. Many tunnels for water/ services are smaller with smaller support needs. Wider than 16 m caverns are out of the RMR system.It is not possible, nor desirable, to propose only a value for support in each subclass. The new guidelines propose an interval of values for certain types of support. More pessimistic values must be chosen for wider tunnels, tunnels with lower RMR values in each class and cases when a higher safety factor is asked for. More optimist ones are chosen for narrower tunnels, and higher RMR values. Some alternatives are almost complementary, others are contradictory. Sometimes several different techniques are proposed Guidelines are not automatic options. Good engineering judgment must be used when choosing between the different alternatives. Guidelines are not mandatory suggestions."

Jan 1, 2015

An essential tool for every step ? Early field survey ? Handheld satellite phones ? Portable satellite phones ? Exploration and Drilling ? Handheld satellite phones ? Portable satellite phones ? Production ? Handheld and portable ? Fixed Satellites systems ? Asset tracking systems Main applications via satellite ? Voice and Fax communication ? Internet access and E-mail ? Video conferencing ? Interconnection to mobile phones, 2 way radios, long range WIFI ? Equipment Tele-maintenance ? Telemedicine ? Crew and morale calling ? Vehicle and asset tracking

May 1, 2006

By D. J. Lucifora

Monitoring-While-Drilling (MWD) is a proven technique that records instantaneous on-drill parameters which can be used to supply contextual information for in-situ, down hole conditions, such as: changes in geology, the presence of pre-existing fractures and dynamic alterations, down hole conditions including bit bailing, bit blockages and bit wear, and improper drill operation. This technique has been widely used in the oil and gas industry and, eventually, it was transferred to the mining industry. A challenge when analyzing and interpreting MWD data is in utilizing proper filtering which enables one to properly eliminate any ?noise? from the signals of interest. Overall the importance of MWD data is that, through the collection of operational field-based data, a dataset can be acquired which allows experimentation and analysis to be carried out. Such a dataset is often impossible to replicate in a laboratory setting. If successful, and through iterative refinement, any promising method can eventually be implemented on-machine and using real-time monitoring techniques. This paper will provide a state of the art review of presently used MWD techniques and applications in industry. The paper?s primary focus will be on shallow, mining-style, blast hole drilling but will also take into account techniques and applications utilized in oil and gas drilling which have not been adopted in the mining industry. In the cases where MWD techniques and applications exist solely in oil and gas drilling the paper will examine and comment on the potential utility of technology transfer to mining applications.

Aug 1, 2013

By C. D. Smith

Numerous studies have shown the potential of air rate profiling to significantly improve the flotation performance of a bank of cells. To date many profiles have been implemented; balanced, increasing, decreasing and combinations of these. Previous work has typically shown using an increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, yields a higher grade for a given recovery compared to other profiles. Air rate profiling can then be thought of as having two distinct components; determining the correct distribution of a given volume of air and, perhaps more importantly determining the correct total volume of air to add to the bank. To date no method for this second component has been established. In an alternative technique the air rate to each cell is adjusted in order to optimise the air recovery from that cell. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement that indicates optimal performance for the operating conditions in the cell, and sets the PAR air rate. By doing this for each cell in the bank, the optimal total air rate to the bank and the optimal distribution of that air can be simultaneously determined. In this study plant trials evaluated different air rate profiles, and profiling based on PAR. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The results showed that the highest cumulative mineral recovery was achieved by operating at air rates which gave the PAR for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this study, the increase in cumulative mineral recovery, at the same upgrade ratio, was more than 33%. Peak in air recovery (PAR) based optimisation of air rates to banks of cells and to the individual cells has been shown to significantly improve flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

By J. Hoover

"IntroductionThis chapter will discuss the operational and maintenance aspects of a heavy media cyclone circuits as applied to coal processing and using magnetite as the media. It deals with heavy media bath separators in terms of types of media, equipment, circuits, media recovery, maintenance, and product handling. It will detail heavy media cyclone operation and supplement the previously described topics.The heavy media cyclone was first developed in the Netherlands by the Dutch State Mines in 1945. A cyclone plant was not built in North America until 1961. Traditionally, heavy media cyclones have been used to treat size fractions between 1lz in. (12 .6 mm) and 35 mesh (0.5 mm). High maintenance related to heavy media bath separators has recently prompted some plants to crush all raw coal to minus 2 in. for treatment in heavy media cyclones.The heavy media bath separators utilize only the force of gravity to make the separation between heavy and light particles. This requires lengthy retention time which can lower capacity and also is inefficient for finer particles. A heavy media cyclone utilizes centrifugal forces which are 20 to 200 times greater than the force of gravity. This means the separation between coal and the impurities occurs very quickly, therefore a low retention time is required allowing cyclones to have high tonnage capacities. Also these greater forces allow better separation for the finer particle sizes.Heavy media cyclones are now widely used to produce both metallurgical and thermal coal. Work is in progress to reduce magnetite consumption, extend wear life, increase tonnage capacity, improve separation efficiency and automatically control these cyclone circuits."

Jan 1, 1989

By Jean Fortin

In order to remain competitive, the search for excellence has been and will remain the only viable option facing the Mount-Wright operations. Safety and environment, process and technology as well as cost performance have been the focus points on which the operations have concentrated their efforts in order to meet and exceed our company&apos;s "Vision 2000" plan. Some of our mine&apos;s accomplishments have been a new work organization, a world class maintenance and a new collective agreement. The concentrator, maintenance and production departments have evaluated their processes and implemented various improvements in areas such as power supply, dewatering, blasting, implementation of service centers for large and small vehicles, fleet standardization, crusher, mills and silos improvements... etc. Safety and work environment for personnel have been our driving force in order to achieve this plan.

May 1, 2003

By E. Swartzman

"IntroductionGENERALLY, the necessity for mining coals of higher impurity content, the drive for lower costs by intensive mine mechanization, changing market requirements, and the increasing competition of oil and natural gas, have continued to result in an upward rise in coal preparation, and have necessitated a more intensive study of coal preparation problems.Increasing adoption of •continuous mining equipment, for example, is introducing new problems in coal preparation. Limited experimental work in the United States (1) shows that the effect of the continuous miner on size distribution varies with the characteristics of the seam. In some seams, the fines problem is lessened, in others it is greatly aggravated. Generally there is a decrease in the relative amount of the top sizes (plus 2 in.) and a substantial increase in the intermediate sizes (down to about 1/8 in.). Contrary to expected results•, where continuous miners with vertical-moving cutting heads are used, an increase in impurities in the slack sizes does not necessarily occur where draw-slate is taken. This is because the draw-slate tends to be kicked out in lump form. However, if a seam contains bands •and lenses of impurities they are bound to be in the mined product."

Jan 1, 1952

By V. Schwinn, P. Fluess, N. Cauderlier, J. Bauer

From a strategic and economic point of view, the development of fine grain high strength steels for long distance pipelines is intensified world wide to satisfy the demand for natural gas in the future.The project related property profiles based on strength, toughness, crack arrest and sometimes resistance against HIC at defined design temperatures require an effective structural refinement using advanced steelmaking and processing in the rolling mill. The microstructure of modern line pipe steels ranges from ferritic pearlitic to ferritic-bainitic and structures where bainite is the dominant component, possibly upgraded by secondary phases. This paper illustrates microstructures and properties of recent orders on line pipe steels both for onshore and offshore application using different processing routes in the plate mill. Examples will be given for SAWL 485 offshore grades, X65 HIC and X70 HIC onshore grades, respectively. Finally, production results of a recent X80 order will be presented.

Jan 1, 2005

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By Kish. L.

"The results of a chemical and mineralogical study of eighteen opaque-oxide occurrences are discussed and the detailed chemical, metallurgical and mining feasibility study of a vanadium-rich magnetite deposit is summarized. A plot of the mol-percentages in the system FeO- Fe2O 3-TiO2 indicates that the deposits fall into two distinct groups: some contain hematite with ilmenite, and some others have magnetite with ilmenite (titaniferous magnetites). The plot also suggests that the two types of deposits were crystallized from liquids of different compositions. Each group has its distinct structural features. Vanadium is present in all of the studied specimens, however concentrations of economic importance have so far been found only in the titaniferous magnetite deposits. The vanadium content of the oxide concentrations of the Dore Lake Complex is the largest among the studied occurrences. Analyses of the concentrates of the drill-core sections show a compositional variation across the orebody; a continuous increase in the tenor of Ti02 and a decrease in the vanadium content upward in the layered sequence is found. Concentration tests on several tons of samples indicate that about 80 per cent of the vanadium is recovered in the magnetite concentrate."

Jan 1, 1972

By F. Liu, S. Rezaei, M. Muinonen, M. Barati, V. L. Lakshmanan, S. Marcuson

Canadian nickel-copper ore deposits have been a major source of nickel, copper, cobalt and precious metals for more than 100 years. The two main minerals of interest, pentlandite (Pn, (Ni,Fe)9S8) and chalcopyrite (Cp, CuFeS2), are usually accompanied by large quantities of pyrrhotite (Po, Fe1-xS). Until the 1950s, Po containing small amounts of nickel was routinely smelted as part of the valuable Ni concentrate. The rapid growth in Ni demand following the Second World War created impetus to treat the Po separately. This action would liberate a valuable smelting capacity for higher value Pn, allow for recovery of Ni locked in Po, convert the Fe to iron oxide or metallic iron pellets, and recover S as sulphuric acid or elemental sulphur. The roasting process also has the potential to produce energy due to the highly exothermic oxidation of Po. The Ni industry would then have a “waste-free” process. Both Inco (now Vale) and Falconbridge (now Glencore) developed processes and built large industrial plants for this purpose that operated with some success. But technical issues and tenuous economics were continual challenges. By the early 1980s these industrial operations were closed. Sophisticated froth flotation methods of rejecting Po were developed, and Po containing up to 1% Ni became a waste material reporting to the tailings stream. As part of a major study on possible processing methods of Po for both value recovery and waste remediation, this paper presents a historical perspective on Canadian Po tailings with regards to their generation, inventory, value, and attempts to process them.

Jan 1, 2017

By L. T. Raevskaia

We discuss the stability problem of a piston of the reversible axial-piston pneumatic motor called DAR-14M. We performed the full analysis of stress and deformation characteristics of the piston near a resonant frequency with the help of FEM ANSYS. We estimated the own frequency of the piston analytically for the given motor, this estimate was confirmed numerically in the model analysis FEM ANSYS. It was also shown in harmonic analysis that loaded piston end behaves very different in comparison to the unloaded end. As expected, maximum deformation was found in the area of the holes of the bearing shaft, indicating an optimization necessary in that region of the motor.

Aug 1, 2013

By J. G. Kelly

"IntroductionOver the past twenty-five years of improvements to scooptrams In the Ontario Division of Inco Ltd., records indicate that on average, an 8 yard capacity machine at 80% availability will load, haul and dump about 100TPH from an average stoping area. This, essentially, means that Inco mines are limited to 2000 TPD as an approximate maximum production cap per minute. Some of the improvements made to scooptrams over this period have been:• dry disc and oil immersed brakes on larger loaders;• to replace air over hydraulic systems;• modulated shift transmissions;• greater breakout and tramming capacities by using larger engines and buckets;• operators&apos; compartments have been enlarged and better seats,• joystick controls and air-conditioned cabs have been utilized&apos;• major cost savings have been realized through tire maintenance improvements; and• major savings, safety improvements and increased ore recovery by using remote controls.After reciting the improvements listed above, and the list is by no means exhaustive, it is quite obvious that scooptrams are a mature product and that major design or performance improvements will not occur in the futre. Any futher improvements will be incremental in nature. Loading, hauling, and dumping with scooptrams is a batch process and as such is limited in its total output.Continuous Load/Crush/Convey Systems:In order to improve productivity, a radical new system was required. The target was 2000 tons per shift. In 1984, to meet the goal, Inco acquired the rights to a contiunous loader from Canadian Mine Services. Inco made modifications to the original prototype machine, such as: (I) conversion from rail mounted to crawlers for increased mobility; (2) a hydraulic cooling system was added; (3) flight bars were changed from cast to forged; (4) motor horsepower increased to 200 hp from 150 hp. Emerging from these modifications came a machine known as the CL-looo Oscilloader (Fig. 1).The CL-looo Oscilloader is an electric hydraulic 35-ton machine which is crawler mounted and has a drawbar pull of 30 tons. It has an adjustable frequency, oscillating lip which simulates the digging action of a manual .shovel. This action agitates and lifts the muckpile enough to allow it to settle by gravity onto the chain and flight conveyor table which then removes the ore to the tail end for discharge into either a crusher, a conveyor, a truck, or a combination of these.Late in 1985, six oscilloaders were fabricated and put into Inco mines for field trials. At Creighton Mine some early field trials were conducted with a rail mounted continuous loader loading directly into 140 cu.ft. Granby cars. Much of the field testing was in VRM drawpoints with the Oscilloader loading into 20-ton trucks or into Teletrams . At Levack Mine, by puttmg the truck on remote control, it was possible to have the operator run the Oscilloader and load his own truck (Fig. 2). At McCreedy West Mine, Copper Cliff North Mine, and Copper Cliff South Mine, the Oscilloaders discharged directly into 26-ton trucks."

Jan 1, 1988