Search Documents

By H. M. Kim, J. Rutqvist, D. W. Ryu

"Demand of high pressurized gas storage in underground rock caverns is increasing. Compressed natural gas (CNG) and compressed air energy storage (CAES) are one of the promising examples after since lined rock cavern (LRC) concept has been verified through in-situ pilot tests. Two key essential concerns of high pressured gas storage in underground rock caverns are mechanical stability of the cavern against high inner storage pressure and the risk of gas leakage from the caverns.In this study, we introduce our results of numerical simulations so as to investigate the potential of monitoring for gas leakage at a pilot facility for CAES in underground LRCs. The pilot facility was constructed at a comparatively shallow depth of 100 m, compared to the previous cases with several hundreds of meters, aiming at validating the feasibility of the LRC storage concept in which inner sealing liners, consisting of steel plate and concrete linings, are installed inside the excavated rock caverns (KIGAM, 2011). Compressed air may leak through either initial defects of inner containment liners such as imperfect welding regions and in-situ construction joints of the liners, or through structurally damaged points of the liners during the CAES operation where compression and decompression of the caverns are necessarily repeated and their structural robustness can be deteriorated.For this perspective, we carried out a coupled thermodynamic and geomechanical deformation analysis using TOUGH-FLAC simulator, and investigated the effectiveness of strain monitoring method in detecting mechanical failure of liners which may provide major pathways of air leakage. We therefore used an equivalent continuum model to relate the localized tangential strain to fracture permeability changes, which was developed in our early work (Rutqvist et al, 2012). In detecting and characterizing the leakage location, we tested a cross correlation technique using the synthetic pressure responses monitored in case of the failure of the inner liners. From the investigations, we showed that tangential strain, rather than radial, monitoring especially at the inner face of the sealing liners can be more effective in detecting the mechanical failure of the liners.In localizing the leakage point, we noted that the interface between the inner liners and surrounding rock may not be perfectly bonded so as to increase permeability through which any leaking air pressure may migrate more dominantly. We also demonstrated that the cross correlation of the time histories of pressure measurement especially at these interfaces can be useful in identifying the leakage point. These results may provide useful information in overall design of monitoring and alarming system of our upcoming CAES pilot facilities."

Jan 1, 2015

By Dean Millar

Clean, green, cheap compressed air can be produced efficiently and renewably by modernization of a 19th century technology ?The hydraulic air compressor has no moving parts ?After commissioning, the Ragged Chutes HAC operated for 70 years, only being stopped twice for repairs to the intake heads ?Operates using hydropower from Montreal river ?Produced air for ~29 silver mines in Cobalt, 20 km distant

May 1, 2013

By H. F. Maulson

For the benefit of those who are not familiar with the history of the western Provinces-Manitoba, Saskatchewan, and Alberta-as regards our natural resources, a few words of explanation may be in order before taking up the consideration of the Mines Act of 1930. In 1867, The British North America Act was passed by the Imperial Parliament. That Act, which is our constitution, created a union between the provinces of Nova Scotia, New Brunswick, and Upper and Lower Canada (now known as Ontario and Quebec respectively) under the name of the Dominion of Canada. Provision was made therein for embracing other parts of Canada from time to time. That portion of Canada which today comprises the Provinces of Manitoba, Saskatchewan, and Alberta and the lands to the north of them, was then known as Ruperts Land and the North West Territory. In the year 1670, King Charles II had granted by Letters Patent to Prince Rupert and his associates, known as ?The Governor & Company of Gentlemen Adventurers of England, Trading into Hudson's Bay?, commonly known as the Hudson's Bay Company, the lands and territories therein described, being roughly all the lands adjacent to and west of Hudson's bay; also the gold and silver to be found or discovered therein and other rights as more fully described in said Letters Patent. The land so granted was called 'Ruperts Land'.

Jan 1, 1930

By A. Galley, R. Tosdal, F. Robert

The Canada Mining Innovation Council (CMIC) Exploration Innovation Consortium developed a 10-year business case for developing new discovery criteria, exploration techniques, and better data management and analysis to improve exploration success in deep, remote, and covered terrains. Within this context, the CMIC devised a five-year project proposal to create improved multiparameter exploration tools to detect ore systems and more efficient vectoring toward high-grade mineralized cores. The Footprints project was approved March 2013. More than CAD$13 million funding was provided through the CMIC-led joint sponsorship from 30 companies and the Natural Sciences and Engineering Research Council. Consistent industry leadership and integration of dedicated industry and academic expertise has the project on track for reaching its well-defined objectives.

Jan 1, 2014

By M. du Plessis, D. F. Malan

"Crush pillars are designed to be in a crushed state whilst being formed at the mining face. The residual stress state of these failed pillars provides a local support function in mining stopes and is used in the majority of the intermediate depth South African platinum mines. On mines utilising crush pillars, the pillar dimensions are selected to achieve a width to height ratio of approximately two. This is not achieved in most cases as a result of practical mining problems and poor pillar-cutting discipline. Furthermore, pillar dimensions are seldom adjusted to compensate for the various factors governing crush pillar behaviour. The pillars should, however, be in a crushed state whilst being formed or whilst still in close proximity to the mining face to prevent potential damaging seismicity.An underground investigation was conducted into the behaviour of the crush pillars in a trial site on the Merensky Reef at Lonmin Plc. The aim of this investigation was to examine the mechanism of pillar crushing and the related rock mass behaviour. The underground test results and pillar behaviour are compared to a limit equilibrium model to investigate if the model provides a useful approximation of the behaviour of the crush pillars. This paper details some of the preliminary findings.INTRODUCTIONOn most mining operations, the design of crush pillars is based on trial and error. As the pillar strength is unknown, the pillar sizes are adjusted to obtain the correct behaviour. Crush pillar dimensions are generally selected to give a width to height ratio (w:h) of approximately 2:1, (Ryder and Jager, 2002). Several factors affect the behaviour of the crush pillars and in many cases satisfactory pillar crushing is not achieved. This results in a seismic hazard in many of the mines using crush pillars. If pillar crushing is not initiated whilst the pillar is being formed at the mining face, as the mining face advances and the pillars move to the back area of a stope, some pillars may burst while oversized pillars may punch into the footwall. If pillars are designed in such a way that they are fractured during cutting by the face abutment stresses so that the pillars will already have yielded and reached their residual strength, further compression of the pillars will be associated with an increase in load and stability will be ensured, (Ozbay and Roberts, 1988). The stiffness of the strata must therefore be greater than the post-peak stiffness of the pillar (Figure 1) or violent pillar failure and hanging wall instability will occur. The pillar design should be aimed at determining pillar dimensions for which the post-peak curve of the pillar is as flat as possible."

Jan 1, 2015

By Arthur L. de Carle

"IntroductionThe Key Lake uranium-nickel deposits are located within a Mineral Lease centred at latitude 57 ° 12' north and longitude 105 °39' west along the southeastern rim of the Athabasca sedimentary basin in northern Saskatchewan, approximately 240 km north of La Ronge (Fig. 1). Access is provided by an allweather provincial highway from Pinchousc, situated about 200 km to the south, and a private airstrip maintained at the mincsitc.These deposits have been developed by Key Lake Mining Corporation on behalf of the Saskatchewan Uranium Joint Venture. Participants in the joint venture include Saskatchewan Mining Development Corporation (50%), Urancrz Exploration and Mining Limited (33 1/3 %) and Eldor Resources Limited (16 2/3 %).Considerable geological work has been conducted on the Key Lake orebodies and reported in summary papers published by Dahlkamp and Thn, (1977), Dahlkamp, (1978), Gatzweiler eta/., (1979) and Kirchner el a/. , (1980). However, intensive geological research is ongoing, particularly since many problems regarding ore genesis and controls remain unresolved . Exploration History and DevelopmentThe events (Gatzweiler eta/., 1980) which led to the discovery of the Key Lake ore bodies began in the summer of 1971 by following up on the reports of airborne radiometric anomalies and anomalous radon values in the Zimmer Lake water situated approximately 5 km to 6 km to the southwest. This work succeeded in locating a few high-grade uranium and nickel-bearing boulders associated with esker material. An integrated program, consisting of various geochemical and geophysical surveys along with diamond drilling, culminated in the discovery of the Gaertner orebody during July 1975. Subsequent fence drilling across the strike extensions of this ore structure located the Deilmann deposit, approximately I km to the northeast, in June 1976"

Jan 1, 1986

By Jean-Marc Simard, Richard Genest

"La mine Agnico-Eagle, localisée près de Joutel, a été découverte en 1962 par le forage d'anomalies électromagnétiques. Exploitée à partir de 1974, elle a déjà produit près de 30 tonnes d’or à partir de 2 puits, le puits Eagle et le puits Telbel, distants de 1,3 km.Le gisement est situé entre le sommet du complexe volcanique de Joutel, à dominante felsique, et la base de l'ensemble sédimentaire de la rivière Harricana. Ces deux unités ont une extension régionale; elles sont orientées NW-SE avec une polarité NE et des pendages subverticaux. Une faille majeure, la faille Harricana, passe de façon subconcordante au contact de ces deux ensembles.La minéralisation aurifère, de 2 à 5 m d’épaisseur moyenne, est liée a une zone carbonatée, comprise entre des tufs felsiques, argilites et sédiments chimiques (éponte inferieure) et des argilites carbonatées (éponte supérieure). Le minerai est constitué habituellement de 20% de fine pyrite disséminée. L’or est en fines particules associées directement à ces grains de pyrite de texture cataclastique.Deux modelés ont été for mules jusqu' a présent pour expliquer la genèse du gisement: une thèse syngenetique (Barnett et a/.1982) et une thèse épigénétique (Wyman et al. 1986). Cette dernière apparalt comme la plus probable du fait de la présence de la minéralisation dans les zones cisaillées a carbonates secondaires et pyrite cataclastique."

Jan 1, 1990

By S. A. G. Poppen, J. Konopka

"Petro-Canada's project investigative and experimental underground work in the Galt coal seam at Kipp, Alberta included the construction of an emergency egress and ventilation raise from surface.The Galt coal seam is 206 m below the surface and covered by 8 m of shale, sandstone and clay beds of the Oldman Formation, 128 m of shale, bentonite beds and sandstone of the Bearpaw Formation, and 70 m of glacial till and basal gravel. Free water was encountered from sand lenses in the glacial till and the basal gravel.Excavation for the ventilation raise was a nominal 2 m diameter and it was lined with a welded, continuous, steel liner of 1.2 m 1.D.Excavation in the glacial till was carried out with a surface bucket drill rig combined with hand mining. Ground support in the glacial till consisted of liner plates and backfill grout. The Bearpaw and Oldman formations were excavated by employing standard raise boring techniques. The individual liner sections of the continuous steel liner were assembled on surface and the entire liner column was lowered into the raise by employing hydraulic lift climbers. The liner column was back-filled with concrete.IntroductionThe Lethbridge Coal Field comprises an area of approximately 1 165 square km in the vicinity of Lethbridge in southern Alberta. Pacific Petroleums Ltd. proposed in a Preliminary Disclosure in January 1979 ""to open an experimental mine prior to development of a producing underground mine with an initial rate of 540,000 tonnes per year"". A 2 900-hectare group of leases in the Kipp-Coalhurst area was selected as the primary target for the Kipp experimental mine. The scope of work for the experimental mine included the construction of an access shaft with production capabilities, the construction of a ventilation and emergency exit raise, drive-ages in coal to yield a bulk sample, gathering of geotechnical information and the testing of experimental mining methods."

Jan 1, 1983

By Larson. William

What is Lunar In-Situ Resource Utilization (ISRU)? ISRU involves any hardware or operation that harnesses and utilizes ?in-situ? resources to create products and services for robotic and human exploration In-Situ Lunar Resources ???Natural? Lunar Resources ??Discarded Materials Lunar ISRU Products and Services ??Excavation, Site Preparation, and Outpost Deployment/Emplacement ??Mission Consumable Production ??Outpost Growth and Self-Sufficiency Benefits of ISRU ??Increased science and exploration hardware (instead of consumables) ??Increased safety, crew exploration time, and self-sufficiency ??Technology spin-in/spin-offs help recycling on Earth & space economy

May 1, 2009

By L. Vu, V. Popov, J. Beland, R. Darling

"The Ferderber gold deposit is of Archean age. It consists of a series of gold-bearing quartz lenses within a shear zone that crosscuts the central part of the quartz dioritic Bourlamaque batholith. On average, this zone strikes N70E and dips 65SE. The Ferderber shear zone, which hosts the ore lenses, has been affected by a succession of tectonic events. A possible early period of brittle shear, accompanied by the formation of quartz lenses, resulted from strike slip movement along the zone. These early quartz veins were subsequently folded and boudinaged during reverse movement that accompanied a prolonged period of ductile shear. More quartz veins were emplaced in the shear zone at this time; these were also deformed by the thrusting. The latest tectonic event to affect the shear zone was a period of brittle fracture.Early dextral strike-slip movement on the shear zone is suggested by the local occurrence of Riedel shears, the preferred association of ore with east-northeast oriented segments of the zone, and by the apparent en echelon arrangement of some ore lenses. The most important event, a reverse movement, is indicatedby the attitudesoffoliation, folds, boudins, COS tectonites and slip planes. The late brittle fracturing formed narrow gouge filled faults, locally flanked by brecciazones, whichrun generally within and parallel to the shear zone, and also conjugate fractures that crosscut the zone.The Ferderber and six other adjacent gold deposits were formed in a structural regime dominated by a generally horizontal north-south regional compression. The Y axis of the strain ellipsoid is east-west and varies from horizontal to a plunge of 25 0 w."

Jan 1, 1987

By F. Calizaya, S. Bhattacharyya

"This study presents the results of a set of sound level measurements carried out in three underground mines where auxiliary fans are used regularly. Sound levels as high as 100 dB(A) by the workings and 115 dB(A) by the fans were measured in these mines. These levels are quite high even for intermittent noise. Ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard-rock mines are presented here. Factors such as fan type, rotational speed, and silencer-duct arrangements and their effects on noise attenuation are discussed. INTRODUCTION Auxiliary fans are used in hard-rock mines extensively. They are used to ventilate development headings, crusher rooms, conveyor transfer points, and underground shops. They are also used in developing long tunnels and ramps. Depending on the flow requirements and space restrictions, single or double stage axial fans with rigid or flexible ducts are used. Usually, they are high pressure (3.75 kPa) fans with flow rates ranging from 7.1 m3/s to 30 m3/s. The input power varies from 15 kW to 113 kW (Mutama, 2004; O’Connor, 2008). Typically, a 113 kW fan can produce sound levels as high a 113 dB(A) (Howes, 2005). Silencers are often omitted for cost reduction purposes or when used, they are not well maintained. Furthermore, silencers provide limited attenuation depending on their length and type. Typically, the sound attenuation ranges from 10 dB(A) for a 1 × D silencer to 14 dB(A) for a 2 × D silencer, where D is the fan diameter. In a mine, the silencer is subject to wear and tear, especially when the silencer is used in harsh environments. The interior lining can get clogged and the acoustic fill can get covered by dust and diesel soot, thus reducing the silencer performance. Periodic cleaning of the interior casing can increase the attenuation capacity of a silencer by 6 to 9 dB(A) (Dabson & Acuña, 2017). However, this requires a special silencer design in which the inner cartridge can be removed, the sound absorbing material replaced, the inner casing cleaned and the whole set retrofitted. A number of techniques can be used to reduce auxiliary fan noise in underground mines. These range from selecting the right fan for the job to installing adequate silencers. The choice depends on the air quantity requirement at the working place, cross-sectional area of the opening, duct diameter, fan type (axial or centrifugal) and local restrictions. Auxiliary ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard rock mines are presented here. Factors such as fan type, rotational speed, duct diameter, and silencer-duct arrangements and their effects on noise attenuation are discussed."

Jan 1, 2019

Proper water and thermal management is essential for obtaining high performance of Proton Exchange Membrane Fuel Cells (PEMFCs). A steady, two-dimensional water and thermal management model was developed, aiming at considering pressure drop, open circuit voltage variation with stack temperature, water vapor effects on membrane conductivity, which made the model physically more reasonable and more suitable for various operating conditions. The model could predict the distributions of a series of important parameters along the flow channel, and thus the effects of various operating and design parameters on the fuel cell performance could be investigated easily by numerical trial-and-error method. The modeling results compared well with the available experimental results from the literatures. The results also showed that the humidification is crucial for the performance of PEMFCs. The model could be a very useful engineering tool for the optimization of PEMFCs.

Jan 1, 2005

By A. E. Moss

"IntroductionTHE WORLD-WIDE search for iron ore has been vastly accelerated during the past fifteen years .and Canada is playing a most prominent role in this prospecting boom. During this period, the search for .and development of iron ore deposits in Canada bas proven eminently successful and there is every indication that exploration will continue to be active for many years.This paper has been prepared primarily for the information of those who have bad little or no experience in iron ore exploration. For convenience, it is divided into three parts: ( 1) a brief discussion of the marketing of iron ores, with special reference to Canadian production; (2) a summary of the main features to be considered when prospecting for or evaluating a potential iron ore deposit; and (3) an outline of the methods and procedures used in the search for the direct-shipping iron ores in the Quebec•-Labrador iron ore field.The Iron Ore MarketDue to the tremendous tonnages of high-grade direct-shipping iron ore indicated in the iron ore fields of the Quebec-Labrador and Steep •Rock areas, it might be assumed that there would have been a sharp decline in iron ore prospecting in this country. On the contrary, the development of these two major fields, which must be classed among the world's greatest, has been responsible for much of the current activity. The search for high and medium grade magnetite deposits is being• conducted in many parts of the country and a number of these have reached the development stage. Production is being expanded from the known fields, such as Wabana in Newfoundland and Michipicoten in Ontario."

Jan 1, 1955

By Paul W. Shelley, Daniel J. Hodges

The mining industry is undergoing a period of rapid transformative change.  This is the result of the social and financial accountabilities that the industry is faced with because of the world’s desire to cap average temperature increase to 1.50C above pre-industrial levels (UNFCC, 2016).  To limit global warming to 1.50C, greenhouse gas emissions must peak before 2025 at the latest and decline 43% by 2030.  In hard rock mining, comminution is identified as the major energy consumer, being responsible for 40-60% of the electricity use.  It follows that comminution is the major greenhouse gas emission process of the mine.  All effort is being made to radically reduce the carbon emissions of comminution. Grinding media plays a large role in the energy consumption and carbon emission story.  In recent years industry practitioners have attempted to quantify the grinding media carbon footprint.  This paper makes a definitive contribution to that discussion.  The grinding media carbon footprint is quantified in Scope 1, 2 and 3 emission terms in the context of a grinding media supplier.  Major emission contributors, steel, natural gas and electricity are discussed in detail.  The steel industry transition is a key factor. The paper will explore the steel industry transition and its effect on grinding media manufacturing.  The carbon footprint of heritage steel process routes are analysed and compared with the process routes of the future.  Emerging steel making technologies are presented and discussed.  The future of the steel manufacturing and procurement route for grinding media is proposed. This narrative allows for a comparison between the heritage carbon footprint and the future carbon footprint of manufactured grinding media.  Of equal importance is the opportunity of reducing the grinding media carbon footprint in the field.  The paper explores possibilities of reducing the grinding media carbon footprint at the customer site.  Media in use options are presented that take account of the mineral characteristics, the mill dynamics, and the product metallurgy to optimise both carbon footprint and media performance. It is intended that this is a landmark paper in the discussion of the carbon footprint of grinding media.

May 4, 2025

By I-H. Jung, J. Kim

"Mg alloys are extensively used as light structural materials in modern industry. Mn and RE (rareearth) metals are effectively used as alloying elements to enhance the properties of Mg alloys. Therefore, the thermodynamic database of those alloys is important in the Mg alloy design and processing. Critical evaluation and optimization of all available literature data for the Mn-RE systems were conducted to obtain reliable thermodynamic functions. The Mn-RE systems shows systematic changes in the phase diagrams and thermodynamic properties with increasing atomic number in the lanthanide series. This systematic approach for all RE elements allows to resolve inconsistencies in the available experimental data. INTRODUCTIONRare Earth (RE) metals are widely used in many industrial fields including permanent magnet, electronic materials and structural materials. As a small addition of RE can enhance magnetic, electronic, optical and mechanical properties of numerous materials, the usage of the RE is still expanding regardless of the strategic control of their supply.Magnesium alloys are getting great scientific and industrial attention as the lightest structural materials. One of the drawbacks of Mg alloys is their poor formability at room temperature due to the limited slip system with hcp crystal structure. Recently, several studies (Farzadfar et al., 2011; Sandloebes et al., 2010; Stanford, 2010; Stanford et al., 2008; Yan et al., 2010) show that the additions of small amounts of RE can considerably enhance the ductility of Mg alloys. Therefore, a lot of research on Mg-RE alloys is undergoing to clarify the role of RE on the enhanced deformation mechanism and to find out the most optimum Mg alloy compositions. In order to respond to the need of Mg-RE alloy development, a large thermodynamic database for Mg alloys containing RE has been developed with critical systematic analysis and optimization of the entire RE series data. This includes the thermodynamic database of the Mg-RE (Kang et al., 2009), Mg-RE-RE (Kang et al., 2009), Mg-Al-RE (Jin et al., 2011; Jin et al., 2010), Mg-Zn-RE and Mg-Mn-RE systems."

Jan 1, 2012

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By L. M. Lowe, D. B. Chambers, D. G. Feasby

"The presence of the naturally occurring radioactive elements uranium and thorium in rare earth (RE) resources can present challenges in achieving regulatory and social acceptance. The discovery and awareness of radioactivity in mineral resources radioactivity typically generates strong public intuitive responses that may be project prohibitive; a significant proportion of such resources contain radioactivity.The objectives of this paper are to demystify the presence of uranium and thorium in RE resources and to demonstrate how a RE project can be safely developed, operated and closed from a radiological perspective. Radioactivity in RE resources is principally thorium-based. Thorium is interesting and challenging from a metallurgical perspective – one of those stubborn metals commonly assessed as refractory. Thorium is difficult to mobilise into solution and easily precipitates out. Thorium is a common element in the earth’s crust – about 10 ppm on average, and natural geophysical systems conclusively demonstrate its immobility. Specific mine tailings contain elevated levels of thorium, but the contained thorium is neither a significant ecological nor a personal hazard.Waste management for a hard rock rare earth project includes the management of mineral processtailings, waste rock, and metallurgical residue. Proven strategies are available for tailings and waste rockfor all climate conditions. The management of the metallurgical residues is potentially more challenging.Example robust strategies for addressing these challenges are presented.A potential way to reduce the radioactivity of rare earth metallurgical wastes is to selectively remove uranium and thorium. Uranium oxide is readily marketable, but its concentration as a byproduct typically triggers extensive regulatory processes. Thorium is presently not marketable, but may be so in the not-too-distant future with the development of thorium-based nuclear energy. The pro’s and con’s of uranium and thorium byproduct recovery are summarized."

Jan 1, 2016

By M. J. Nicol, T. Moyo

Ammoniacal solutions are an effective lixiviant for the oxidative dissolution of some mineral sulphides. A detailed study of the anodic dissolution of chalcopyrite in ammonium sulphate-ammonium hydroxide solutions has been carried out using cyclic voltammetry, chrono-amperometry and rest potential measurements. The role of the copper(II)/copper(I) redox couple in the oxidation process has been evaluated. Rest potentials have been found not to be affected by oxygen but to increase with an increase in initial copper(II) concentration. Pseudo-steady-state anodic current densities measured in the absence of copper(II) ions at the rest potentials obtained in the presence of copper(II) ions increase with increasing concentration of copper(II) ions, confirming the positive effect of copper(II) ions on the rate of dissolution of the mineral. Cyclic voltametric and chrono-amperometric data show that in the absence of initial copper(II) ions, the rate of dissolution in the presence of dissolved oxygen is significantly lower. These results confirm that the effective oxidant for the mineral under the conditions of the study is copper(II) and not dissolved oxygen. Coulometric measurements have been used to establish the stoichiometry of the anodic reaction at different potentials.

Jan 1, 2014

By Lynn I. Kelley

Potash is the primary industrial mineral produced in Saskatchewan, followed, in terms of gross value, by aggregate, sodium sulphate, salt, potassium sulphate, peat, clays, silica sand, calcium chloride brine and "clinker." Potentially economic deposits of kaolin, diamond and building stone are under evaluation.

Jan 1, 2001

By M. Kermani

This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill has an alkali activator such as sodium silicate in its materials in addition to primary materials of cemented mine backfill which are deslimed tailings, water and binders. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. Initially, the influence of sodium silicate concentration on the mechanical properties of samples was evaluated using the unconfined compressive strength (UCS) test. Consequently, the effect of curing temperature on CHF and Gelfill samples cured in various curing temperatures ranging from 5?50 °C was studied using the UCS test. Microstructure of selected samples was studied wirth the mercury intrusion porosimetry (MIP) technique. This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Curing temperature strongly influences the mechanical and microstructural properties of CHF and Gelfill samples. (iv) The microstructure analysis revealed that the addition of sodium silicate can modify the pore size distribution and total porosity of Gelfill which can contribute to the better mechanical properties of Gelfill. (v) The MIP tests suggested the microstructure of specimens were changed by adding sodium silicate in a way that the Gelfill samples had a higher percentage of fine pores than CHF samples.

Aug 1, 2013