Search Documents

By Callaghan T

The Henty Gold Mine is located approximately 30 km north of Queenstown, at the head waters of the Henty River on the west coast of Tasmania at 41¦50'S, 145¦40'E on the Queenstown (SK 55-5) 1:250 000 and Sophia (8014) 1:100 000 map sheets (Figure 1). The mine is accessed from Queenstown along the A10 Highway and Anthony's Road. The town of Queenstown is located 260 km north west of Hobart on the A10 Highway, and

Jan 1, 1997

By Penny T. G

BHP Diamonds and their joint-venture participants DiaMet Minerals, Chuck Fipke and Stewart Blusson are currently developing Canada's first commercial diamond mine in the arctic barren lands of the Northwest Territories (NWT) of Canada. The paper reviews the early history of the project leading up to the discovery of the first kimberlite pipe in September 1991, diamond exploration techniques and the subsequent advanced exploration and development work carried out at the site. In many aspects, this exploration work represented a development project in itself. Coinciding with the advanced exploration work, the project team prepared an Environmental Impact Statement (EIS) and went through federal review of the project at the highest level. External affairs strategies regarding the federal review and aboriginal land claim issues were crucial components to the approval process. Upon approval in principle by the

Jan 1, 1997

By Chowdhury P. J R, Biswas S. K

Recovery of metallic values from lean-grade raw materials as well as from secondary/intermediate industrial products is of immense importance to a country like India which is not endowed with extensive sources of copper and nickel. The results of a few studies carried out in this area are described in Part-I and Part-II in this article. A novel anode casting system, specially designed for a small copper refinery which had been set up to produce copper wire bars/rods is described briefly in Part-III.

Jan 1, 1992

The original leases making up today's North Kalgurli Mines were developed by independent companies on an ad hoc basis. The major disadvantage which now arises is the varying levels of mining horizons. From Kalgurli Shaft in the south, through main Shaft and to Croesus Shaft in the north, there are three separate sets of levels. work has commenced to link the three areas with either common levels or new development which will facilitate common access and haulage via Main Shaft.Generally, the workings at North Kalgurli were established at the turn of the century. The introduction of techniques and equipment to bring the mine into the 20th Century has been difficult and slow. The general size of openings, a widespread workforce and complex ore distribution often make innovation and change more than a challenge.

Jan 1, 1985

By Estoque J, Abaigar J, Domingo B, Acenas M

The Siana gold-silver deposit of Surigao del Norte, Mindanao, Philippines is perhaps one of the most complex in the world, being related to an ancient suture zone known as the Philippine Fault. Early accounts described the deposit as epithermal, consisting of an upper limestone replacement orebody and a lower vein type deposit hosted in andesite. Recent field and laboratory studies, in correlation with the latest findings on the archipelago's tectonic evolution, however, led to the present interpretation of the Siana ore deposit's origin as involving both syngenetic and epigenetic processes, with limestone breccia, similar to the Cow Head Breccia of Newfoundland, as the principal host to mineralization.

Jan 1, 1987

Whilst decisions to commit projects have traditionally been heavily influenced by hurdle rates for d.c.f. analysis, it is suggested that evaluation of competitors' costs may be a desirable additional tool.The MICAS system developed over the past four years is described. This computer system uses standard costs modified by District and Mine factors to allow estimation of individual mine costs. The data base contains more than 15,000 items of data and more than 6000 costs are calculated.Recent applications include use for competitive analysis, predictive analysis, statistical analysis, and comparative assessments with scopes ranging from a few mines to the whole Australian export industry. Some areas where care is necessary are outlined and potential further uses are discussed.

Jan 1, 1985

By Chugh Y. P

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in- mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer Prediction.

Jan 1, 1992

A good blasting result is largely achieved by putting the right amount of explosive in the right place and firing it in the right sequence. The best blast design in the world will not break the rock if the planned blast layout is not achieved in the field. One of the critical inputs into a blast design is the diameter of the blasthole. An assumption that the actual blasthole diameter is equal to the nominal drill bit size is generally made. However, a small deviation in the actual hole diameter from that assumed will have a dramatic effect on the hole's volume and, consequently, where the explosive is placed in the blasthole. Any discrepancy in actual blasthole volume from that assumed will be reflected in 'overloading' or 'underloading' of the blasthole with the calculated explosive quantity and, thus, reflect in explosive distribution and stemming lengths. When loading to a 'collar' in an oversized hole extra explosive will be used, resulting in higher than planned powder factors and explosive costs. A blasthole diameter assumed from a nominal drill bit size is an incorrect assumption. This paper will present some actual blasthole diameter measurements illustrating the variation in hole diameters seen in the field and proposes a practical method for achieving a useful blasthole diameter measurement.

Jan 1, 1990

A major problem in the continuous casting of aluminium killed strip steel is the incidence of black and grey lines in the strip surface caused by the alumina inclusions. One place for limiting the number of alumina inclusions is by providing favourable fluid flow conditions in the ladle so that the inclusions float out to the surface or adhere to the ladle wall. In laboratory equipment 20 kg of steel was melted in an alumina crucible of 14 cm diameter in an induction furnace. Deoxidation was carried out while the melt was constantly stirred by argon bubbling. Bubble frequencies were measured at the lance tip using a microphone technique. High speed cine photo- graphy was incorporated to measure melt top surface velocities. Experimental results indicate that the rate of removal of inclusions is a function of both the gas input and the power input. However due to unfavourable surface area to volume ratio, reoxidation of the melt took place. Some other experimental difficulties in working at high temperatures are also discussed such as lance design, melting arrangement and sampling techniques.

Jan 1, 1984

By Blake W

Based on preliminary computer model simulations and stability analyses, both longi- tudinal and transverse, large dimension, cut- and-fill rooms were designed for the parallel dipping ore layers at Kamoto mine. Full scale testing of the designed rooms showed that the rooms are stable and that the rock behavior is predictable. Ordinary waste rock was selected as the filling material because the fill was found to carry little load.

Jan 1, 1973

By Johnson RD

The variation in coal properties and the coal seam reduced level can be analysed using partial trend-surface analysis techniques. For the area studied seam reduced level and seam thickness data from the Bulli Coal yield trend-surfaces with a high coefficient of determination, since they have relatively small systematic local and random components in their overall variation. Sulphur content appears to have no significant re.gi_onal trend, and phosphorus content has a very weak regional trend. Other analytical variables have regional trends which are of intermediate strength. The strike-directions of.the statistically significant first degree! trend-surface are similar, sug-gesting.: that the variation of the several coal properties was controlled by a set of- related causes. The relations apparent from the dip and strike of the first degree trend-surfaces are similar to- those which are apparent from the trend- surface residuals and'from the results' of canonical trend-surface analysis.'.. It is probable that differential subsidence controlled the areal

Jan 1, 1975

By Streichfuss M, KeBler H-W, Burgwinkel P

This paper describes the design of an expert system used as a part of a diagnostic system for diesel hydraulic drives. A PC-based diagnostic system ruDi (KeBler and Burgwinkel, 1993) was developed to minimise the time for diagnosis and repair work of vehicles with diesel hydraulic drives used in the mining industry. One part of ruDi is an expert system that helps to locate errors in any of a vehicle's subsystems, and supports technicians in removing the cause of a malfunction. Apart from the standard knowledge of diesel engines and hydraulic transmissions, the expert system supports the interpretation of the data obtained during sophisticated engine analysis tests such as high-resolution speed analysis or high-pressure analysis of the diesel injection system. The expert system is designed to diagnose various vehicles of the same type. Data for each vehicle is stored separately allowing checks to be carried out individually for each machine. An additional feature of this system is a database interface to a Maintenance Planning and Control System (MPCS) that allows an automatic generation of work orders for the defects found during the expert system sessions.

Jan 1, 1995

By M F. Lee

In order to make good decisions, as to whether large diameter raise bored shafts can be constructed in blocky rock at a particular location, mine planners, management, geotechnical engineers and contractors must understand and consider a range of geotechnical issues. Firstly, mine management must ensure that adequate time and resources are available to find appropriate shaft sites. Deep weathering, adverse structures, groundwater, etc might mean that the most desirable location, with respect to other mine development, might not be suitable. Special site investigation drilling, etc may be necessary. Even then, alternative construction options might be necessary, other than just reaming through to the surface. A site investigation borehole should then be drilled to investigate specific and general ground conditions along the raise alignment. Often, only small sections of weak blocky rock dictate raise stability. While the empirical McCracken and Stacey method is typically used in Australia to assess raise stability and assess geotechnical risk, until recently it had no published performance data.An Australian database of raise performance now exists and is presented below, courtesy of an industry survey by the Eastern Australian Ground Control Group. Raise diameter and ground conditions (in terms of a lower bound Qr value) is presented for 50 cases versus raise performance.

Jan 1, 2008

Naturally occurring rutile contains approximately 96 per cent titanium dioxide (Ti02), whereas the product from the ilmenite reduction - aeration upgrading process, "sub- rutile", contains only about 92 per cent Ti02. Therefore, there is an-incentive to lift the quality of sub-rutile by removing transition metal impurities, in order to supply a more valuable and marketable product, particularly for the chloride-route pigment producers. Previous studies have shown that the sub- rutile residual iron content (of approximately 4 per cent) and residual manganese content (of approximately 1.5 per cent) are chemically bound within the titanium-oxygen mineral lattice, and are most difficult to remove by simple leaching methods. In attempts to improve their eventual removal, a simple process modification has been successfully investigated in laboratory scale trials. Transition metal sulphides have been formed in the reduced ilmenite by using a "sulphur-doping" technique during reduction (metallization) conducted at controlled temperatures. These compounds give rise to greatly enhanced dissolution of the unwanted transition metal constituents during the sub- sequent aeration and acid washing steps. Thus, the manganese content of the final sulphur- doped, reduced-aerated, acid washed product can be reduced by about 90 per cent to 0.2 per cent, and the iron content by about 70 per cent to less than 1.5 per cent, in comparison with those levels remaining after unmodified pro- cessing. Additions of sulphur as low as 2 per cent of the weight of the ilmenite have proven satisfactory. Preliminary studies reveal that the modified process is economically feasible. These results suggest that the sulphur content of the Collie coal char used in an unmodified reduction step must exert some influence on the eventual removal of iron and manganese during aeration and acid washing.

Jan 1, 1973

By H Rose, T J. Sheer, M Dumka

Whenever rock is tipped from above, severe eruptions of airborne dust occur into the airways connected to tipping stations of rock passes (ore and waste) on the lower levels of a gold mine in the North West Province of South Africa. An investigation was undertaken to understand the nature of the physical phenomenon, in order to propose possible solutions. Accordingly, measurements were taken underground, involving the simultaneous logging at two levels of the transient pressures produced in the orepass by tipping from various levels. Two portable data loggers with associated transducers were custom-built for this purpose. Measurements were taken during a tipping program in which rock quantities and levels were controlled. Pressure pulses that are generated by the falling rock drive the airborne-dust eruptions. When tipping from a specified level, recorded pressure pulse waveforms were found to be repeatable on any given level, irrespective of the amount of rock falling, but measurements were conspicuously different on different levels. It was recognised that a pressure pulse is generated as the falling rock passes through the constricted region û a relatively narrow neck û at each tipping station. In passing through the constricted areas the mass of falling rock acts as a æleaky piston in a cylinderÆ and compresses the length of the air column in the orepass below that level. Once the rock has passed through the constriction, the pressure is released and this behaviour causes a regular train of pressure pulses that are separated by the time taken for the rock to move from one level to the next. Based on this physical understanding of the dust eruptions, a computational model has been developed that can reproduce all the main features of the measured phenomena. The model has been verified adequately against the measurements and can now form the basis for simulating a range of possible engineering solutions.

Jan 1, 2005

By J Czerwinski, M Kasper, M Wyser, N Heeb

The VERT project 1993 - 1998 laid the technical foundation for curtailing the emission of fine particles from diesel engines at Swiss underground workplaces. The targeted maximum was 100 ¦g/m3 EC. Extensive laboratory and field investigations demonstrated that this specification is only attainable with modern diesel particulate filter (DPF) systems that almost eliminate particles in the entire lung penetrating size range from 20 nm to 2.5 ¦m. In January 2000, Switzerland mandated compulsory particle filters in underground workplaces, particularly in tunnelling, irrespective of engine age, size and type. After the implementation, the particle concentration in the respiratory air was below 40 ¦g/m3 EC, compared to earlier values of up to 750 ¦g/m3 EC. Deployed DPFs have proven filtration rates of 99 per cent in the entire size range of alveoli intruding particles. The DPFs are as durable as the engine, suffer no ageing and require minimal maintenance. The failure rate is below three per cent annually. Of the 6000 retrofitted construction machines in Switzerland, about 400 are deployed underground. Prerequisites for this quality are a sophisticated certification procedure, electronic monitoring of DPF operation and meticulous periodic exhaust gas inspection of the engines.

Jan 1, 2005

A standard practice of auditing mill designs has developed in the mining industry. The purported aim of this task is to ensure that the mill being offered conforms to the design specification, thus reducing the purchaserÆs risk. However, careful examination of the auditing methods used in the past shows that this is not the case. In some cases, what auditors have been providing is effectively a quality assurance check of the input data, not a full independent audit of the vendorÆs design. It will be shown that these past auditing methods have contributed to the stagnation of mill specification development. This lack of specification improvement combined with the current trend towards increased allowable fatigue stress ranges can result in an increase in risk for the purchaser.

Jan 1, 2002

By W Stange

Assessing the risks in a mining project is a key aspect of project evaluation. This is an exacting and demanding task because of the complexity due to the need to deal with uncertainty over long time periods. The way risks are assessed and managed is critical to the long-term success of the projects and the business. Discounted cash flow (DCF) analysis is commonly used for project and risk evaluation. A discount rate is selected that accounts for uncertainties in the cash flows. However, it is difficult to determine an appropriate discount rate due to the large number of factors that need to be considered and the complex relationships between risk sources. Using a proven framework, ævalue at riskÆ (VaR), this paper proposes to rigorously model and quantify ærisk at sourceÆ. The approach was first employed to assess financial market risks and is now widely used in the banking sector for risk assessment. In project evaluation, all risk sources are identified and estimated separately to ensure the overall project risk is quantified accurately. A bottom-up approach has been proposed. Estimates are first carried out for risk factors at the bottom of the project structure. The assessment is then applied at increasingly higher levels until the overall project risk is estimated. Value at risk is a versatile methodology and can be used in a local or integrated manner. The final value is objective and the calculation steps can be easily justified and followed. Four case studies have been included to illustrate how the proposed approach can assist management in decision-making.

Jan 1, 2009

By Kim YC

An alternative development drilling strategy to the one currently in use at an open pit mine was investigated using geostatistics for a portion of the pit. The massive orebody, the 3-D nature of the problem, and the location of ultimate pit limit in the study area all created some unique problems in devising the development drilling strategy. Rather than using confidence interval of the global reserve estimate as the main criterion for development drilling, the confidence interval of short and medium range mine planning blocks was used as the objective. Based on somewhat arbitrarily selected level of confidence, the results from the study showed that a total of 50 diamond drillholes (DDHs) rather than the planned 62 DDHs is sufficient in the study area, if the selected confidence levels are acceptable to the management. The paper also emphasizes the importance of particular objectives being used in development drilling and how they influence the "optimal" placement of the development drillholes.

Jan 1, 1986

By Hall T. P, Taylor R. N

Fluid flow in a 1:14 scale water model of the shaft and settler of the Kalgoorlie Nickel flash smelter has been investigated by flow visualisation and numerical modelling. Detailed flow fields through the reaction shaft, settling chamber and uptake are presented for flow rates up to 800 Vm and a number of burner configurations. The predicted flow fields were compared with experimental data obtained from streak photographs and video recordings. The effects of cessation of flow through individual burners and changes in shaft dimensions were also Investigated.

Jan 1, 1992