Search Documents

By R.K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By R. K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By H. R. Banks

PONDERING the action of a ball mill employed to carry on comminution from the product of fine crushing to the point where flotation, cyanidation or other concentrating methods are applicable, one wonders where this machine had its origin. When Henry Wadsworth Longfellow reiterated the observation of that older poet Von Logau, and wrote “Tho’ the mills of God grind slowly, yet they grind exceeding small," he probably visualized the type of mill that was employed in medieval times for the production of flour, and can therefore not be considered as having gained admittance to the fraternity of millmen, on behalf of, either poet. He does, however, make it quite clear that the efficiency of even these Mills of Destiny was low, and to that extent voices a characteristic of fine-grinding equipment that has been the bugbear of all metallurgical engineers. PRINCIPLE OF BALL MILL The principle of the ball mill probably is traceable to the action along the coast line of oceans or lakes, or in the mountain streams. Wave action on rocks and pebbles, close to the shore line, gives the potential energy to the grinding media, which, in their rolling and tossing, break down the sands, and the resultant "pulp" carried out from the shore is classified and settles out in sizes ranging downward to extremely fine mesh. Surely, these are the real mills of God. If we allow our minds to dwell on the total tonnage that has been handled in this way, adding to the sands and clays at present in existence those enormous tonnages of metamorphosed sedimentaries, we sense the vast quantity of rock that has been so reduced. Is it not likely, therefore, that the answer to the beginnings of pebble milling, and eventually ball milling, came through the perception of this natural mill by one of our engineering forebears? METHODS OF GRINDING The relatively low return of mechanical input to a ball mill, in terms of useful work accomplished, has always intrigued me immensely. The potential energy absorbed by a ball raised to a high point in its path is apparently released with a very small return in useful work. Is the ball mill the most desirable means of fine grinding, or is there some other method through which we can recover a reasonable amount of the energy input in terms of useful work? Some years ago, on his retirement, H. W. Hardinge was questioned as to his thoughts on the trend of fine-grinding equipment. As I recall, his prophecy at that time was that the most likely field for improvement in grinding media would be toward a charge of flat disks with some mechanical scheme to cause them to slide over each other. Undoubtedly, Mr. Hardinge went through the usual experience of the muller and bucking board, the customary introduction of the budding millman to his calling. I have often wondered, but have never got beyond the wondering stage, as to the

Jan 1, 1945

By A. L. Mular

The flotability of crushed zinc oxide pellets which were doped to produce more n-type or less n-type (more p-type) properties was studied with a Halli-mond tube. Flotation data are presented to show that the pH at which 50% recovery occurs and the collector concentration for 50% recovery depends upon the concentration of doping agent added substitu-tionally for zinc in zinc oxide. The time of sintering of pellets has a slight effect on flotation behavior. A speculative model is proposed to explain the observed behavior in light of the fact that zinc oxide is a semiconductor and has a space charge region at the surface. Experimental verification is necessary before the proposed model can be established as correct. In recent years, the attachment of flotation reagents to minerals has been shown to depend upon the behavior of an electrical double layer which exists in the liquid near the mineral-liquid interface.' Thus, a mineral placed in water will undergo a surface re-arrangement, most likely be preferential dissociation of lattice atoms or by surface adsorp-tion-desorption reactions, to form a dissociation electrical double layer with the solution. Among the many factors which influence adsorption processes, the past history of the mineral itself is one of the most important. Because of trace impurities, minerals from different localities may exhibit marked differences in flotation behavior. This is not unexpected, since investigators who have studied the detailed structure of the double layer's3 have known for some time that the impurity content of many minerals may exert strong influence on double layer variables. For this reason, their studies were usually made with minerals of high purity. The precise relationship between impurities in a mineral and double layer parameters such as capacity and electrostatic potential has been obscure. However, impurities in a semiconductor type mineral which is in contact with a solution have been recently shown to produce changes in the properties of a space charge layer which extends into the bulk of the semiconductor to a distance of one micron or more.4 The double layer is influenced by the space charge layer, whose origin is best discussed in terms of the band theory of solids. A qualitative description of the behavior of impurities in the bulk of a semiconductor, from a chemical point of view, is useful at this point. Briefly, impurities or defects (lattice vacancies, interstitials, etc.) in semiconductors such as PbS, ZnS, FeS2, Cu2S, NiS, NiO, Fe2O3, ZnO, CdS, MnO2 and many others, behave somewhat like acids or bases in water. For example, water dissociates into hydrogen and hydroxyl ions according to

Jan 1, 1965

By S. Floreen, H. W. Hayden

The effects of additions of iridium, rhodium, ruthenium, and platinum on the mechanical properties of Fe-C alloys were determined. Each alloying element significantly improved the toughness. The results support the general correlation that substitutional alloying elements that stabilize austenite are beneficial to toughness, but the reason for this improvement is not obvious at this time. The effects of substitutional alloying elements on the toughness of steel has long been a subject of both practical and theoretical interest. Despite the obvious importance of this subject, there has been little progress toward understanding the mechanisms by which alloying elements influence the fracture behavior. In some cases the deleterious effects of alloying elements have been shown to be due to mechanisms such as embrit-tlement of prior austenite grain boundaries or inhibition of cross slip in the ferrite lattice. In other cases, however, the reasons for the change in properties are not clear. This is particularly true for elements, such as nickel, that improve the resistance to brittle fracture. Several investigators'-3 have pointed out that there is a correlation between an alloying element's phase diagram with iron and its effect on toughness. Those substitutional alloying elements that stabilize austenite generally are beneficial to toughness, while ferrite-stabilizing elements generally are detrimental to toughness. The word "generally" should be emphasized, because exceptions to this rule can be found. Nevertheless, this correlation does offer a starting point at which to try to understand the effects of alloying elements on toughness. Thus far only two austenite-stabilizing elements, manganese and nickel, have been considered. In order to test the validity of this correlation several other austenite-stabilizing elements were evaluated. The noble metals, iridium, rhodium, ruthenium, and platinum, have binary phase diagrams with iron similar to the Fe-Ni and Fe-Mn diagrams. That is, each element expands the austenite field, and also higher concentrations of each element produce martensitic transformations at low temperatures. Presumably then, each of these elements should improve the toughness of steel. The present study was conducted to determine if this were so. EXPERIMENTAL PROCEDURE The alloys were made as l-lb air-induction melts using electrolytic iron and commercially pure noble metals. Each heat was initially deoxidized by a carbon boil, and further carbon was added to attempt to produce a 0.05 wt pct C content in each alloy. Before pouring, a final refining addition of 0.2 wt pct A1 and 0.1 wt pct Ti was made to each heat. The alloys were cast in a copper mold to produce ingots approximately 1 in. in diam and 5 in. long. The chemical compositions of the alloys tested are given in Table I. The residual nitrogen, aluminum, and titanium contents were all relatively constant at 0.003, 0.03, and 0.02 pct, respectively. The carbon

Jan 1, 1968

By J. Kent Smith

VANADIUM is generally spoken of as a rare element; but, even in the light of our resources as known a couple of years ago, this description could be accepted in a qualified sense only. In fact, vanadium is very widely distributed, being a constituent of most clays, while even caustic soda has been shown to contain almost regularly a minute proportion of it, although the quantity in each case is so small as to render impracticable the extraction of the metal there from with profit. The opening-up of a large deposit of vanadium sulphide ore in South America has put a new phase on the commercial outlook of vanadium, the technical value of which for the improvement of steel has been proved by rigorous scientific investigation.

Sep 1, 1907

By Louis Cates

AT THE annual meeting of the American Institute of Mining and Metallurgical Engineers in February, 1923, the Chairman of the Committee on Ground Movement and Subsidence appointed a subcommittee to work out a form of questionnaire and to collect data on subsidence and ground movement resulting from underground metal- and coal-mining operations, and on ground movement and safe slopes in connection with open-cut metal-mining operations. The author was requested to take charge of the collection of data and the preparation of a questionnaire in connection with the Committee's studies of open-cut metal-mining operations, this paper is a summary of the work carried on and information received therefrom up to February, 1924. The first approach to the problem of safe slopes is to gather all information that pertains to finished slopes; in other words, the steepest economic angle from the horizontal that will stand in order to uncover the ores to be mined and be safe while the extraction of the ore at the base of these slopes is in progress. Whether or not this angle is 35° or 45° depends on many factors. The number of benches maintained to take care of falling rock and their height and width are direct functions of this overall slope. The slope is here taken to mean the angle from the top edge of the pit through the edges of the respective lower benches to the bottom of the pit. If we accept this definition of the slope, it might save some confusion as there would be a difference if one took the line from the top edge of excavation to the toe of the bottom slope. This latter slope would not be constant, but would vary with the number of benches. The depth of the various ore faces will vary, of course, depending on the deposit; Table 1 shows this to range from 50 ft. to 1100 ft. The geology is an important factor, as are the climatic conditions under which one is operating. A saturated condition in some rock structure causes rock flows; in the Panama Canal excavation, slides have run on a ratio of as low as one on ten, which is a 10 per cent. grade, or a slope of less than 6° with the horizontal. Slopes as steep as 60° have been noted in the Utah Copper operations, so that a wide divergence will possibly be

Jan 8, 1924

By J. Szekely, V. Stanek

Steady state heat transfer and fluid flow rates are predicted for the counter-current contacting of gas and solid streams. For a .fixed pressure drop across the bed the convective heat transfer rate is affected by the gas flow rate, which in turn is affected by the temperature distribution in the system. Variations in bed voidage and in particle size were found to change the predicted temperature profiles quite markedly, in particular when the thermal capacities of the gas and solid streams were equal. IN Part I we examined the effect of step and pulse changes in the inlet gas temperature on transients in the flow of gases through fixed packed beds. Here we shall discuss heat flow and fluid flow interactions in the counter-current heat exchange between packed solids and a gas stream. Counter-current heat exchange in packed beds has been extensively studied. In his now classical paper, Furnas' assumed constant property values and developed a simple analytical. expression for the temperature profiles in the gas and in the solid stream. A highly sophisticated analysis of counterflow systems, allowing for transients and interparticle conduction was developed by Amundsen. In preparing a very readable review of this topic Elliott' also presented a number of elegant solutions, including the case involving heat generation. A great deal of work has been done on the application of these concepts to the modelling of the blast furnace. However, in all this previous work the mass flow of the gas was regarded as a quantity independent of the gas-solid heat exchange process. In the following we shall consider counter-current heat exchange between a gas stream and a packed bed of solids, under conditions where the pressure drop across the bed is specified, rather than the mass flow of the gas. FORMULATION Consider a packed bed, extending from y' = 0 to y' = L, in which moving solids and a moving gas are contacted in a counterflow arrangement. Let cold solids, with an initial temperature Tsi and mass flow GA, enter at y' = L, and hot gas with an initial temperature of Tgi and mass flow Gg enter at y' = 0. In contrast to the problems considered in Part I this system has a nontrivial steady state and we shall restrict our attention to the study of the pressure drop flow relationships and the resultant temperature distributions for steady state conditions. Under these conditions the formulation of the problem requires the statement of the following: 1) heat balance on the gas 2) heat balance on the solids 3) the mechanical energy balance equation and in addition the knowledge of the equation of state, and a functional relationship between viscosity and temperature and an expression for the heat transfer coefficient in terms of the other parameters. On neglecting temperature gradients within the solids and for a constant mass flow of the gas, the solution to this problem is well known.'" The expressions for the temperature profiles of the gas and solid streams may be put in the following form: where Tg and T, denote the dimensionless gas and solid temperatures respectively, y is a dimensionless distance, and R is the ratio of the thermal masses. These quantities are defined as follows: For the particular case of equal thermal mass capacities by the gas and the solid, that is R = 1, the Eqs. [1]and[2] simplify to Eqs. (71 and[8], respectively: i.e., the resultant profiles are linear. As for most practical cases , solutions given by Eqs. [7] and [8] will contain only the inlet temperatures as parameters. For a fixed, predetermined value of C;b the above

Jan 1, 1970

By Charles L. Thomas

A novel, highly sensitive, and reproducible nzetlzod for the determination of hydrogen in solid materials is presented. The procedure requires equilibration of the specimen with hydrogen gas, rapid quenching, and hot vacuum extraction of the dissolved gas with subse-quent quantitative analysis by mass spectroscopy. Good linearity is obtained for the Arrl~enius plots of the investigated metals. The advantages in the use of this method over that of Sieverts aye discussed. The solubility data for copper are in reasonable agveewzent with a considerable number of other inuestigations, wllile those fov silver are considerably lower than previously reported. The first known solubility data for gold are presented. Solubility equations and heats of MUCH of the data which are available on the solubility of hydrogen in various metals and alloys have been obtained by the classical Sieverts method.' The method involves the measurement of a decrease in pressure of a gas in a calibrated system, and the calculated contraction in volume is attributed to the solubility of the gas in the metal sample. The procedure requires several corrections, such as the solubility of the gas in the container walls and the diffusion of the gas through these walls, as noted by Steacie and .Johnson2 and others. In addition, errors may be incurred due to reactions between metal surface impurities, such as oxides, and the saturating gas. The precise calibration of the measuring system where large thermal gradients exist can present additional difficulties. Also, accurate volumetric measurements of small quantities of gas are difficult. Many of the objections to the Sieverts method were overcome on solid materials by Ransley and ~eufeld,~ who first saturated the metal with hydrogen and performed a subsequent extraction and measurement of the gas by chemical means. Eichenauer and pebler4 and Eichenauer, Kiinzig, and pebler5 measured the diffusion coefficient and solubility by following the degasification of a sample as a function of a rate of increase in pressure in a previously evacuated system. Here again, however, the procedure involves many of the corrections of the Sie-verts method. The present investigation deals with the solubility of hydrogen in solid copper, silver, and gold by a technique which eliminates many of the aforementioned corrections and possible errors. This procedure requires equilibration of the specimen with gas, rapid quenching, and hot vacuum extraction of the dissolved gas with subsequent quantitative analysis by mass spectroscopy. EXPERIMENTAL Two completely separate systems were employed to accomplish first, the equilibrium saturation of the sample and second, the extraction of the dissolved gas. Saturation Apparatus. The saturation apparatus, illustrated in Fig. l, consisted of a vertically mounted quartz tube with a three-way valve for vacuum or hydrogen near the top and an outlet near the bottom leading to a butyl phthalate seal. The bottom end of the tube was terminated with a joint accommodating an O-ring sealed "Asco Stirring Gland" (The Emil Greiner Co.). This gland facilitated movement of the thermocouple without introduction of air into the system. The upper portion of the tube (above the furnace) was water-jacketed. A Welsh 1405-B mechanical pump provided the necessary system evacu-

Jan 1, 1968

By M. Garfinkle, W. D. Klopp, W. R. Witzke

The tensile properties of binary W-Re alloys containing up to 33 at. pct Re were determined at temperatures from 78" to 3630°F. Elongations as high as 260 pct were observed in electron-beam-melted tungsten containing 23 at. pct Re when tensile-tested at 3630°F after a 1-hr anneal at 3090°F. All alloys tested under these conditions with rhenium contents between 20 and 28 at. pct exhibited elongations of at least 200 pct. These alloys also showed enhanced grain growth rates. The values of strain-rate sensitivity ranged between 0.2 and 0.3 for the alloys exhibiting high elongations. Houlezler, for swaged alloys tested just above the re-crystallization temperature, strain-rate sensitivities as high as 0.8 were observed. The high-temperature strengths of the high-rhenium-content alloys were also less than those of alloys with intermediate rhenium contents. ALLOYING with rhenium has two distinct effects on the mechanical properties of tungsten. One effect occurs in dilute solid solutions and is most clearly seen in the lowering of the hardness and of the ductile-brittle transition temperature at about 5 at. pct Re.1-3 The second effect occurs in the concentrated solid solution at about 25 at. pct Re, and is characterized by twinning and a larger decrease in the ductile-brittle transition temperature. An aspect of the high-rhenium-content alloy which has received little attention is the higher-than-usual tensile ductility at 3500°F.3 Anomalous high ductility has been observed in several other alloy systems. usually associated with a phase transformation or a solid-solubility limit.4'5 The phenomenon is now commonly termed superplasticity. High-strain-rate sensitivities6 and grain boundary sliding7 have been reported for materials that undergo superplastic deformation. Also, it has been found that superplastic materials usually have a very fine grain structure (less than 10 pm).8 and it has been proposedg that such a structure alone is sufficient for superplasticity. The purpose of the present study was to further characterize the high-temperature tensile properties of W-Re alloys to determine the conditions under which they might be superplastic. Tensile and selected strain-rate sensitivity tests were conducted on alloys containing 0 to 33.3 at. pct Re at temperatures from 78" to 3630°F. Grain-growth rates were also determined on most alloys at 3630°F. Fig. 1 indicates the compositions evaluated and their locations relative to the solvus line in the tungsten-rich end of the W-Re phase diagram. Twelve binary W-Re alloys containing up to 33.3 at pct Re were double electron-beam-melted and subsequently fabricated to 0.3-in. rod by extrusion and swaging. The starting materials were commercial powders of tungsten and rhenium with impurity levels as listed in Table I. The various blended W-Re compositions were hydrostatically pressed at 70 ksi. The pressed bars were drip-melted into 1.5-in.-diam ingots and then remelted into 2-in.-diam ingots at a chamber pressure of 10~5 torr. The ingots were canned in molybdenum and extruded to round bar at a reduction ratio of 6:l. The alloy extrusions were swaged to about an 80 pct reduction at 2100" to 2900°F. Buttonhead tensile specimens with a reduced section diameter of 0.16 in. and a gage length of 1.0 in. were centerless-ground from the swaged bars

Jan 1, 1970

By E. W. Johnson, M. L. Hill

Cold working of iron-carbon alloys was found to increase greatly the hydrogen solubility and to decrease the diffusivity at temperatures up to 400° C. These effects are increasing functions of both the carbon content and the degree of deformation. The hydrogen behavior is consistent with the idea that cotd working creates "traps", which are concluded to be microcracks in which the hydrogen is chemisorbed. Hydrogen embrittlement is explained by the Petch theory of metal crack surface energy loss due to hydrogen adsorption. HYDROGEN embrittlement of steel has been studied for many years and has been the subject of an extensive literature, but the mechanism of the effect has not been completely understood. The embrittlement is unusual in that the ductility loss is not accompanied by an increase of the yield strength, being primarily a decrease of the fracture strength alone. The loss of fracture strength is usually most severe in the temperature range between 0°and 100°C. Here the solubility of hydrogen in the iron lattice at ordinary H2 pressures is extremely low while the diffusivity is still quite high. From the relationships between the ductility and the hydrogen content, test temperature and strain rate, it is apparent that the hydrogen atoms causing the ductility loss difbse to and concentrate in small regions of the metal which are especially susceptible to the initiation and propagation of fracture. This hydrogen segregation apparently occurs after plastic straining has begun. Below 0°C the ductility loss persists only at low strain rates in confirmation of the view that the embrittlement is diffusion .controlled. The tendency of the embrittlement to disappear above 100°C can be explained by the increasing lattice solubility of hydrogen with rising temperature. A common view of hydrogen embrittlement of steel is that the hydrogen initially dissolved in the metal lattice diffuses to structural discontinuities and there precipitates as H2 gas at very high pressures which assist the external stress in causing premature failure.1,2 The idea of a high H2 pressure in equilibrium with ordinary amounts of hydrogen in steel at room temperature is due to observations of hydrogen behavior in fully annealed material, for which the Sieverts' law constant relating solute concentration to H2 pressure is extremely small. Hydrogen-embrittled steel, however, is always plastically deformed to some extent, and therefore it is important that hydrogen embrittlement be explained primarily in terms of hydrogen behavior in plastically deformed material. Such an explanation is attempted in this paper. Previous studies of hydrogen in cold-worked steel have shown that both the solubility and the diffusion rate are significantly chaned when the steel is cold worked. Darken and Smith discovered that the amount of hydrogen absorbed from acid by cold-rolled steel at 35°C is many times greater than that absorbed by hot-rolled steel. They found also that the hydrogen permeability of the steel is unaffected by cold working. Keeler and Davis4 confirmed the high apparent solubility of hydrogen in cold-worked iron-carbon alloys at temperatures up to and even beyond the recrystallization temperature. They also found that this solubility increase accompanying cold work is a sensitive function of the carbon content, being absent when no carbon is present. The present experimental study was undertaken primarily to obtain an improved understanding of the behavior of hydrogen in cold-worked steel. Data were obtained on the effects of temperature, H, pressure, carbon content, and degree of cold work on the hydrogen solubility and diffusivity in iron-carbon alloys. These data have been helpful in elucidating the nature of the cold-worked steel structure as well as in providing information on the mechanism of hydrogen embrittlement of steel. EXPERIMENTAL Cylindrical specimens for hydrogen absorption and diffusion rate measurements were prepared from three iron-carbon binary alloys and a commercial SAE 1010 steel. The iron-carbon alloys were prepared by vacuum melting electrolytic iron with graphite in a magnesia crucible. The alloys were cast in vacuum as 2 1/2-in. sq ingots weighing about 20 lb each. The ingots were hot rolled (above 1900°F) to 5/8-in.-diam round bars and then cooled in air to room temperature. The resulting metallographic structure consisted of islands of fine pearlite surrounded by free ferrite. Chemical analyses of the materials are given in Table I. The 5/8-in. diam bars were turned to diameters such that cold reduction to the desired final specimen diameters would result in either 30 or 60 pct reduction in area (RA). The machined bars were then cold worked by swaging at room temperature

Jan 1, 1960

By Francis Clark

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200° C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating. EXPERIMENTAL WORK The object of the experimental work was to study the effect of mechanical work on rolled 60:40 brass, quenched and reheated, and the mechanism of twinning in the alpha reeds of a furnace-cooled specimen. It was desired to determine the effect of mechanical work on the transformations taking place on reheating the quenched material, both at 200 and at 470° C. A study of the nature of the structure resulting from the breakdown of the beta at 200° C. and a study of the mechanism of twinning above 470° C. were considered problems for investigation. The question of the twinning of the alpha reeds was also an important phase of the work. With high-power magnifications, there was hope of following these processes.

Jan 1, 1927

By Louis D. Huntoon

The Porcupine gold area, located on the Hudson Bay slope of northern Ontario, has produced over $100,000,000 in gold and has paid more than $28,000,000 in dividends, since the first real production in 1912. The character of the ore has been studied by the geologists of the Bureau of Mines of Ontario, the geological staffs of the operating mines, and engineers commissioned to examine properties there. What information the Government has is free to everybody; the geological staffs of the several properties also give to the visiting engineer what information regarding ore deposition they possess, and the author wishes to express his indebtedness to the geologists of the Ontario Bureau of Mines and the staffs of the operating mines for their free discussion of geological questions. This paper is based on the examination of several properties, various petrographic reports, not only on specimens from Porcupine but from elsewhere in northern Ontario, and interviews with Government and mine staff geologists. The petrographic work has been done by Prof. R. J. Colony, of Columbia University. Geological History The geological history of the district may be summarized as follows: The outpouring of great floods of lava accompanied by beds of tuff, flow following flow; the contacts of different flows can be seen in various parts of the camp. This period mas followed by an uplift and the production of the Temiskaming sediments by erosion. Later, dynamic action turned the sediments and underlying lavas on edge; this was followed by the intrusion of igneous rocks—in the Porcupine area the quartz porphyry, which is of such great importance in connection with the gold deposits. Doctor Burrows says: "The intrusions of quartz porphyry have in some way influenced the deposition or location of the gold but it is not likely the porphyry has been the source of the gold-bearing solutions." This statement of Doctor Burrows I indorse. The formation of non-gold bearing quartz veins followed the intrusion of the porphyry. These veins occur along or near the contact of

Jan 1, 1923

By Nelson Severinghaus

The Rock Chapel plant of Consolidated Quarries Corporation (Fig. 1) is three miles northeast of Lithonia, DeKalb County, Georgia. It was opened about eight years ago for crushed stone aggregate. This paper reviews a number of experiments that have been tried in drilling and blasting, and gives the practice in use today. It also presents several theories on the action of explosives in this type of blasting. The rock worked is a bare dome of granite gneiss about 3000 ft. in diameter, rising 150 ft. above the surrounding ground (Fig. 2). It is uniform in composition and quality, without seams, and extends downward to unknown depth below the quarry floor. A water well drilled 600 ft. remained in the same rock. The principal difficulty encountered in blasting is an easy split, which tends to break down the rock in large blocks.

Jan 1, 1938

By R. A. Harrington, H. R. Nelson

The: structure of anodic films formed on aluminum and other metals under varied conditions is not well known despite the wide use of such films both as protective coatings and as the dielectric medium in electrolytic condensers. The present work was undertaken as a survey of the possibilities of electron diffraction in the investigation of anodic films, especially in comparing the properties of anodic films formed under different sets of conditions and subjected to various subsequent treatments. In addition, an effort has been made to compare surface films formed on aluminum by anodic treatment with surface films formed by heating, immersion in chemicals, etc. The elcctron diffraction method in many cases has been successfully applied to the study of thin surface films. Its principal advantage is that it can be used without removing the films from the base material upon which they have been formed. The low penetrating power of electrons, in the "reflection" diffraction method which has been used in this work, prevents the appearance of diffraction patterns from substances at depths greater than about 100 Angstrom units (lop6 cm.). Different investigations of the structure of anodic films have showll widely varying results, depending on the methods used in preparing the films. Apparently under some conditions these films are crystalline and under other conditions they are amorphous, and it has been difficult to say which type of structure will be found in any particular case. Schmid and Wassermann's1 X-ray diffraction patterns of eloxal‡ films show two broad, diffuse bands, which these investigators attribute to finely divided cubic y-Al2O3.§ Burgers, Claassen, and Zernicke³ obtained sharp X-ray

Jan 1, 1940

By Louis D. Huntoon

The Porcupine gold area, located on the Hudson Bay slope of northern Ontario, has produced over $100,000,000 in gold and has paid more than $28,000,000 in dividends, since the first real production in 1912. The character of the ore has been studied by the geologists of the Bureau of Mines of Ontario, the geological staffs of the operating mines, and engineers commissioned to examine properties there. What information the Government has is free to everybody; the geological staffs of the several properties also give to the visiting engineer what information regarding ore deposition they possess, and the author wishes to express his indebtedness to the geologists of the Ontario Bureau of Mines and the staffs of the operating mines for their free discussion of geological questions. This paper is based on the examination of several properties, various petrographic reports, not only on specimens from Porcupine but from elsewhere in northern Ontario, and interviews with Government and mine staff geologists. The petrographic work has been done by Prof. R. J. Colony, of Columbia University. Geological History The geological history of the district may be summarized as follows: The outpouring of great floods of lava accompanied by beds of tuff, flow following flow; the contacts of different flows can be seen in various parts of the camp. This period mas followed by an uplift and the production of the Temiskaming sediments by erosion. Later, dynamic action turned the sediments and underlying lavas on edge; this was followed by the intrusion of igneous rocks—in the Porcupine area the quartz porphyry, which is of such great importance in connection with the gold deposits. Doctor Burrows says: "The intrusions of quartz porphyry have in some way influenced the deposition or location of the gold but it is not likely the porphyry has been the source of the gold-bearing solutions." This statement of Doctor Burrows I indorse. The formation of non-gold bearing quartz veins followed the intrusion of the porphyry. These veins occur along or near the contact of

Jan 1, 1923

By R. A. Harrington, H. R. Nelson

The: structure of anodic films formed on aluminum and other metals under varied conditions is not well known despite the wide use of such films both as protective coatings and as the dielectric medium in electrolytic condensers. The present work was undertaken as a survey of the possibilities of electron diffraction in the investigation of anodic films, especially in comparing the properties of anodic films formed under different sets of conditions and subjected to various subsequent treatments. In addition, an effort has been made to compare surface films formed on aluminum by anodic treatment with surface films formed by heating, immersion in chemicals, etc. The elcctron diffraction method in many cases has been successfully applied to the study of thin surface films. Its principal advantage is that it can be used without removing the films from the base material upon which they have been formed. The low penetrating power of electrons, in the "reflection" diffraction method which has been used in this work, prevents the appearance of diffraction patterns from substances at depths greater than about 100 Angstrom units (lop6 cm.). Different investigations of the structure of anodic films have showll widely varying results, depending on the methods used in preparing the films. Apparently under some conditions these films are crystalline and under other conditions they are amorphous, and it has been difficult to say which type of structure will be found in any particular case. Schmid and Wassermann's1 X-ray diffraction patterns of eloxal‡ films show two broad, diffuse bands, which these investigators attribute to finely divided cubic y-Al2O3.§ Burgers, Claassen, and Zernicke³ obtained sharp X-ray

Jan 1, 1940

By C. Ernest Birchenall

As a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.1 In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in. the preceding paper.2 A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken .3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity data given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below.

Jan 1, 1947

By Robert B. Fulton

It is a pleasure to talk to you about the world economics of industrial minerals on this occasion of AIME's 100th anniversary. In order to fit this topic into the time and tenor of such a session as this where you are hearing subjects equally broad in scope one after the other, I will deal with the subject through the medium of eight minerals selected to illustrate import- ant economic factors. I must admit to some bias in the selection, since I picked personally familiar ones to elucidate facts of life in the industrial minerals business. It is a very interesting field, different in many respects from metals and certainly far different from petroleum. The minerals chosen are celestite, diamond, fluorspar, salt, sulfur, ilmenite, rutile and zircon. Celestite The market for celestite is mainly in the U. S. where it is consumed in the manufacture of strontium compounds for red-colored flares and other pyrotechnics, for the production of electrolytic zinc, for glass manufacture, and for the manufacture of ceramic ferrites. Smaller markets exist in Europe and Japan. Production comes from England, Mexico and Spain, and a new mining operation is being started in Nova Scotia. There is no significant production in the U. S. nor in the other principal consuming countries, except England; so it is mainly an international commodity. Celestite illustrates many of the factors important in the economics of industrial minerals. To have a marketable product, grade and freedom from deleterious elements are important for materials used by the chemical industry. In the celestite used to make strontium nitrate, calcium is the most objectionable of the commonly associated cations. Selling price is adversely affected because nitrate manufacturing costs are greatly increased if calcium is pre sent, hence less can be paid for the raw material. Meeting specifications can add significantly to the vendor's cost; hence a balance must be struck between the producer's capability and the consumer's requirements, permitting a reasonable profit for both. Sizing of industrial mineral products is often important to the consum-

Jan 1, 1971

By John F. Allan

This paper does not pretend to advance any facts or improvements not known to many members of the Institute, but is intended merely to give a few practical hints on preliminary tests, and to call attention to a possible enlarged field for the cyanide process in the treatment of some silver-ores, which merits investigation. Broadly considered, the choice of a process for the treatment of silver-ores in Mexico is confined to the following alternatives: (1) Concentration for treatment by smelting; (2) milling and pan-amalgamation; (3) the patio and Ortega process; [4) chloridizing roast and lixiviation; (5) chloridizing roast and cyaniding; and (6) cyaniding of the crude ore. These methods of treatment may also be combined, and cyaniding or concentration, or both, may be introduced, at what-ever stage it is found to be most advantageous. The characteristics of the ore (especially its gold-content) and local conditions, such as distance from railway, cost of fuel, amount of water available, vary so much that it is impossible to make general comparisons between the different processes, either as to extraction or cost. Concentration and subsequent smelting may be made very expensive by long-distance transportation of concentrates; pan-amalgamation is undoubtedly expensive; and the patio process is barred when the ore contains appreciable amounts of gold, by reason of its poor extraction of that metal; yet there are many ores for which each of these processes is especially adapted, and the expense of treatment is compensated by the results obtained.

Jan 1, 1905