Search Documents

By P. G. Shewmon

If interfacial equilibrium is maintained at the interface between a growing precipitate and the supersaturated matrix, so that solute diffusion alone determines the growth rate, the precipitate shape should evolve toward that characteristic of the dendrites found in solidification. However, this shape is rarely observed in precipitation reactions proceeding at high temperatures where interfacial equilibrium is usually felt to prevail. Thus some other stabilizing factor must enter, to keep the interface smooth. It is shown that a slow interfacial reaction (low interfacial mobility) will stabilize the interface, while transformation stresses have a IN studying the kinetics of phase transformations such as solidification or proeutectoid precipitation at high temperatures, it is customary to assume that equilibrium exists across the interface and that the rate of the reaction is determined by the rate at which heat and solute diffuse to and from the interface. In the case of precipitation, such an assumption predicts an almost infinite rate of initial growth. It is generally stated that the rate cannot be infinite and that during some initial period the rate must be determined not by solute diffusion but by an interfacial reaction, i.e., transferring atoms across the interface. The duration of this much weaker stabilizing eFfect and impurities tend to enhance instability. It is also concluded that a sets an upper limit on the wavelength of the perturbation that can give instability. Thus initially all flat or smoothly curved particle interfaces will be stable even if their growth is diffusion-controlled. Proeutectoid precipitation in the Fe-C system is considered in some detail and it is shown that the experimental results can only be rationalized if the growth rate of ferrite in steel transformations is determined by a slow interfacial reaction for all hut a few orientations between the two phases. initial period has never been clearly established, but it is generally assumed to be too short to affect any measurable results.' Several authors have pointed out that in the case of interfacial equilibrium any bump in the surface will grow out ahead of the planar interface due to the higher gradient in front of it.2j3 Thus the interface will be unstable with respect to an irregular interface with points (plates) propagating rapidly out ahead of the interface into the supersaturated phase. Recently, Mullins and Sekerka have given equations for the stabilizing effect of surface tenion.~ They found that for particles with a radius of curvature of 1 p or greater the stabilizing effect of surface tension will be completely overcome by a supercooling, or supersaturation, of as little as

Jan 1, 1965

By AIME AIME

THE 1941 fall meeting of the Iron and Steel and the Institute- of Metal, Division held at the Ritz-Carlton Hotel, Philadelphia, during the first three days (Oct. 20-22) of the National Metal Congress was well attended as usual, and the seven technical sessions and the joint round table on order-disorder transformations were this year of considerably more than routine interest. Despite unseasonably warm weather, a scarcity of hotels (there were rumors, apparently well-founded, that , some of the metal man attending the Congress had to stay in tourist camp), and a multiplicity of technical and other ions of the co-operating societies that gave the Congress this year the general air of a three-ring circus the A.I.M.E. sessions attracted audiences that ragged from seventy or eighty up to 350

Jan 1, 1941

By Paul F. Kerr

QUARTZ of a certain kind, is one of our strategic minerals, and Brazil is probably the one important available source. Crystals of quartz of suitable size and perfection for piezoelectrical application are rare; their most outstanding use is in radio work. Clear quartz, or "crystal," free from twinning, cracks, foreign particles of other disturbing lines of growth, and gaseous or liquid inclusions, is cut into plates which provide excellent control of frequency in broadcasting. The squares or rectangles are less than a millimeter in thickness and ordinarily on the order of 1 in. along each side. They are cut at definite angles with respect to the axes of the crystal, and ground with opposite surfaces parallel. Each small slab must be a section of one crystal, uniform throughout in atomic alignment. The thickness of the chip controls the frequency of a broadcast and it is most important to have the plates oriented and ground with utmost precision. Opposite surfaces are parallel to within 0.001 mm. and expansion or contraction due to the temperature is limited to one part in a million.

Jan 1, 1942

By John V. Beall

Since the U. S. Metals Refining Co. works was established, around the turn of the century, near the town which is now called Carteret, N. J., it has grown to be a major producer of refined copper and the main source of that special brand known as "oxygen-free high-conductivity copper." Owing to the complex metallurgical problems arising from handling a variety of raw materials such as copper concentrate from Matahambre, Cuba, copper and brass scrap from the New York area, and domestic blister copper, the organization is geared from top management down through its 2000 employes to maintain a high degree of flexibility in plant operation. The Company is a subsidiary of The American Metal Co. Charges for the smelter furnaces, one reverberatory furnace and one blast furnace, are made up in. bedding bins so that they may be tailored to the production of a constant grade of blister copper. The reverberatory furnace smelts the .sulphide charge, which may be a blend of ten different materials but principally the Cuban concentrate, and the matte from the process is poured into a converter. This reverberatory is 80 by 20 ft, silica lined with a slag bottom, fired by pulverized coal, and continuously side-charged from the top by bottom-dump cars which keep the side walls covered. It produces a 40 to 50 per cent copper matte. The fuel-charge ratio is 4.35 tons of solid charge per ton of coal. The furnace has a capacity of 10,000 tons of charge per month and produces from 5000 to 6000 tons of slag per month which must be disposed of. About 5000 tons of converter slag is produced monthly and returned molten to the reverberatory furnace. The converter gases go through a spray chamber to a Cottrell precipitator and thence to the flue system. Smoke from the

Jan 1, 1948

By J. F. K. Brown

ANTHRACITE?S satisfactory showing in 1942 was accomplished in the face of adverse conditions, such as the loss of man power to the active services and to other industries, and the difficulty and delay in obtaining the necessary materials and equipment required in mining operations. Although the in- creased output was stimulated by the war, and thus does not impress one as contributing to continuing improvement in the industry, nevertheless the year witnessed several efforts ant1 consideration of others that have the appearance of permanent progress.

Jan 1, 1943

By William Hurst

Muskat's depletion performance equation is here derived considering the expansion behavior of the reservoir hydrocarbon system and a simple fractional-flow equation. This nietkod of derivation leads logically to the two extensions that follow. The first of these is concerned with gravity segregation in a depletion-drive reservoir. The second is concerned with including an empirically determined tern? for water influx in the performance equation. The more general equation for gravity segregation when there is a primary gas cap and empirically-determined water influx is stated for completeness. These equations have been found useful in reservoir performance calculations in Eastern Venezuela. A discussion on the methods of solving these equations follows, and considers firstly the effect of taking finite intervals in the numerical integration, and sec-ondly, methods of incorporating the time functions involved in segregation in with the expansion behavior. The paper concludes with a brief general discussion on further extensions to the depletion performance equation. INTRODUCTION The two fundamental sources of energy by which oil is produced from a reservoir result from pressure depletion inside the boundaries of the reservoir and fluid encroachment across the boundaries of the reservoir. The wells in either case form low pressure outlets through which oil and gas may be produced by the expansive force of the reservoir fluids and associated encroaching fluids. When the reservoir pressure is higher than the bubble-point pressure of the oil, so that there is no free gas in the reservoir, these expansive forces are the only ones available for the production of oil. However, when the reservoir pressure is less than the bubble-point pressure of the oil, free gas is vaporized as the pressure falls. With both oil and free-gas phases present, the additional forces of gravity and capillarity may operate on the gas-oil system, as they have previously operated on the oil-interstitial water system. Gravity tends to segregate the free gas from the oil due to their density difference. Capillarity opposes and eventually balances gravity as the more extreme free gas and oil saturations are reached, preventing the independent move- ment of free gas until it is above a certain saturation, and the independent movement of oil when it is below a certain saturation. The type of depletion performance equation chosen for predicting the future performance of a reservoir depends on the amount of past history available. When the reservoir is somewhere past the halfway mark in depletion, some form of decline curve is often used. With less past history, material balance equations which incorporate empirical factors based on the past performance are often used. When, however, the amount of past history is small, the Muskat depletion performance equation will usually be used. The distinguishing feature of this type of equation is that empirical factors based on the over-all or macroscopic reservoir behavior are almost or entirely absent. Each parameter affecting the reservoir performance is ascribed an independent set of values based on measurements made on laboratory samples; that is, incorporating microscopic empirical factors. In establishing Muskat-type depletion performance equations, it is necessary to consider the reservoir as consisting of a number of associated blocks, in each of which the saturations and pressures may be considered uniform, and in each of which all substances have uniform pressure-volume characteristics. Thus, a primary gas cap can usually be considered as one block and an aquifer as another. Gravity segregation may be negligible for practical purposes when the rock and oil properties are adverse and/or the dip or thickness of the reservoir is too small. In this case the whole oil leg may be considered as one block, except in very large reservoirs. In very large reservoirs the fluid and rock properties may vary enough, particularly in the dip direction, for it to be necessary to divide the oil leg into a number of blocks, in each of which the relevant quantities may be considered uniform. When gravity segregation of the oil and free gas is not negligible, it is necessary to consider the space occupied by the initial oil leg as divided into two blocks, a secondary gas cap and an effective oil leg, in each of which saturations may be considered to be uniform. The total volume of these two blocks is thus constant, but the secondary gas cap grows continuously at the expense of the oil leg. Muskat1 derived depletion performance equations for the basic case of an oil reservoir with closed boundaries and without segregation, and for the case of an oil

By S. C. Dhara

A process of solvent extraction and separation of platinum group metals (PGM) and gold using primary, secondary, tertiary, and quarternary organic amines has been briefly described. The effects of amine structures; the use of diluents; the principle of synergism and antisynergism in the mixed extractants; the oxidation states of metal ions are explained in the amine extraction process of precious metals.

Jan 1, 1984

By Norman Brown, J. V. Rinnovatore

It was found that a shear stress applied during the recovery had no effect on the amount of recovery if the stress was less than the instantaneous yield point irrespective of the direction of the stress. Large ajplied stresses during recovery had a marked effect, which depended on the direction of stressing. Single strain reversals at -72°C not only produced the Bausch-inger effect but also increased the flow stress. The increase inflow stress was attributed to vacancies, which have appreciable mobility at -72 °C. THEORIES I-' of recovery suggest that the internal stress field of the dislocations plays an essential role. Most investigations of recovery use time and temperature as the independent variables; however, here stress has been introduced as a variable in two ways: 1) by varying the internal stress field according to the amount of strain prior to recovery and 2) by applying an external stress during recovery. Tannen- baum and Kauzrnann studied the effect of applying a stress during recovery by measuring the change in creep rate after recovery; they found that stresses as high as 95 pct of the creep stress had no effect on recovery. Earlier, Wood and scrutton6 showed that an applied stress during creep increased the rate of poly-gonization. The experiment by Wood involved poly-crystalline aluminum whereas Tannenbaum and Kauzmann used a single crystal of zinc. In this investigation, zinc single crystals were used and deformed in a manner to prevent polygonization. Thus, the main difference between this investigation and that of Tannenbaum and Kauzmann is the use of the stress-strain curve instead of creep rate as the index of recovery. In addition, the applied stress during recovery varied

Jan 1, 1961

By Arthur Fleischer

THE Kalunite process? for the production of metal-grade alumina from alumina-containing ores is applicable, considered from a general point of view, to any aluminous raw material that can be converted to potassium alum or equivalent normal alum. This result of modern technology has been the subject of a continuous study and development since 1929, on a laboratory and test-plant scale, with initial emphasis on the utilization of alunite as the raw material. The research and developmental program was carried out by the Kalunite Company and its successor, Kalunite, Inc., an affiliate of the Olin Corporation of East Alton, Illinois. The process is now approaching the time for a major test in its history with the completion of construction of a plant having a capacity of zoo tons of alumina per day in Salt Lake City for the conversion of Marysvale, Utah, alunite ores to alumina and potassium sulphate. The Salt Lake Alumina Plant is a Defense Plant Corporation project. PRODUCTION OF ALUMINUM The known existence of alunite deposits, especially in the Marysvale district, furnished the motive for the original inquiry into the utilization of this raw material for aluminum production. The deposits in this region were actively explored during World War I and utilized for the production of potassium sulphate, an essential fertilizer, of which a shortage of monumental proportions then existed. Up to the twentieth century for alunite is a mineral with an ancient history-it was used in Europe and in China as a source of potassium alum. It never had been used successfully in. this country as a source of oxide for reduction to metal. Although the known reserves of this ore, which undoubtedly will be greatly expanded with a commercial outlet for this ore, are recognized to be sufficient for only a part of the present-day needs of aluminum, it has a definite place in the aluminum industry. Academically it points the way for future raw materials. The aluminum industry has undergone a remarkable growth in the past few years as a result of defense and war requirements. Its expansion in many ways has been beyond belief and prediction, both in volume and location. This wartime status of the industry has accelerated the consumption of bauxite to such an extent, that a re-evaluation of the raw material reserves for the future peacetime industry and for eventual wartime reserves is seemingly of concern. The generally accepted picture of bauxite ore reserves in the United States, especially in raw material suitable for treatment by the Bayer process, focuses attention on other possible sources of raw material of metal-grade oxide. The perspective for the development of a suitable process may have changed in the interim

Jan 1, 1944

By S. R. Balajee, I. Iwasaki

The adsorption mechanism of corn starch and its derivatives at mineral-solution interfaces was investigated by the adsorption of cationic starch, unmodified corn starch, British Gum 9084, and anionic starch on quartz and hematite. The adsorption of these starches, which decreases in the order mentioned, is dependent on the balance between the magnitude of the electrostatic interaction and the magnitude of the hydrogen bonding. There exists a critical starch concentration for both optimum flotation and flocculation conditions of iron ores, which corresponds to a point where the starch adsorption reaches a saturation coverage. Flocculation occurs due to the adsorption of starch via electrostatic and hydrogen-bonding forces and by interparticle bridging as a result of the conformation of starch molecules at the interface. The depressant property of starches and starch derivatives in flotation' and their flocculation char: acteristics in clarification and filtration2.3 have long been recognized on a wide variety of ores. The effectiveness of a starch as a depressant for iron minerals has been the subject of much investigation in recent years both in the amine flotation of siliceous gangue and in the anionic flotation of activated silica from iron ores. It has been reported that the depressant activity of starches and dextrins in the cationic flotation of quartz from hematite increases with molecular weight, branching, and number of hydroxyl groups, 1 and that the selectivity is affected by changing the configuration of starch molecules and the composition of its polar groups.4 ,5 The manner in which starches are solubilized was shown to exert a significant influence as a depressant in the anionic silica flotation, and a series of articles covering the practical aspects of flotation and flocculation have already been reported.618 Chemical modification of the starch structure, the pulp pH, the calcium ion, and the residual starch concentration were identified as some of the more important variables affecting the flotation behavior. In the flocculation of iron ores, it was noted that most starches flocculated suspensions of hematite in water but did not flocculate similar suspensions of quartz,9 and that an excessive use of starch restabilized the suspensions due presumably to protective action. 6 An admirable application of such an observation to practice may be cited in the selective flocculation and desliming in the anionic silica flotation of iron ores, which resulted in superior metallurgy and lower reagent cost. 10 From detailed adsorption measurements, Schulz'and Cooke4 established that the adsorption of starches and their derivatives depended on the types of minerals and of starches, pH, and electrolytes present. Their adsorption data and the foregoing flotation and flocculation observations suggested that an electrical interaction between starches and charged mineral surfaces might be playing a role in their adsorption process. Adsorption of organic polymers, particularly of synthetic origin, at solid-liquid interfaces has been extensively studied in recent years,' and it is realized that their adsorption mechanism is considerably more complex than that of simple ions or molecules. A polymer molecule possesses a number of functional groups, and the adsorption at a point may restrict the adsorbability of adjacent groups. The mechanism may be further complicated by the conformation of the polymer molecules which may exist as coiled spheres, helices, or extended chains as a result of intramolecular interactions among functional groups as well as intermolecular interactions with solvent molecules. The object of the present investigation was to examine the effect of the chemical modification on the adsorption characteristics of starches and starch products on quartz and hematite at several pH values, so that by correlating this information with flocculation and flotation results, adsorption mechanism of starches on mineral-solution interface may be elucidated. EXPERIMENTAL MATERIALS Quartz: St. Peter sand was screened at 35 mesh and the undersize was scrubbed and deslimed at a Fagergren cell. The deslimed sand was cleaned with 0.1 N hot hydrochloric acid and washed repeatedly with distilled water, For anuscript, measurementsl the -200-mesh fraction of the sand was ground dry in a porcelain mill for 3 hr. The specific surface of the finely ground quartz was

Jan 1, 1970

By G. K. Manning, A. R. Elsea, A. B. Westerman

INTRODUCTION A CONSIDERABLE number of high-temperature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. At the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in Vitallium after various heat treatments. However, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases- might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chromium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja1 and Guertler2 indicated that cobalt and chromium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to '85 pct chromium undergo a transformation at 1200 to 1250°C. More recently, Wever and Haschimoto,3 Wever and Lange,4 and Matsunaga5 carried out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallographic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Matsunaga. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these exceptions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data and the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitallium by determining the diagram for the cobalt-chromium system. EXPERIMENTAL WORK For the convenience of the reader, the diagram as determined by the present investigation is presented in Fig g. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the, melting point for pure chromium is the

Jan 1, 1948

By C. F. Gates, H. J. Ramey

Recent literature shows that pronounced increases in oil recovery can result from the use of miscible systems in recovery operations. This literature also points out certain problems associated with maintaining miscibility, e.g., compositional changes resulting from alterations in pressure and temperature or from zone dilution. The purpose of the work described in this paper was to study miscible zones for possible use in waterflooding operations and examine the manner in which these zones break down. The fluid system selected for study was oil—terNary-butyl alcohol—water, which, because of its narrow range of miscibility, is ideally suited for investigation in short, linear systems. The laboratory-observed effects on oil recovery and zone stability of a number of variables are reported. Among the variables investigated were miscible zone size, viscosity ratio, length of travel, and interstitial water saturation. Results obtained with this system show that interstitial water adversely affects recoveries because of premature phase break. Salinity of the water further aggravates Ais situation. This effect, although pronounced for this system, would probably occur in any fluid system containing an alcohol. As expected, viscosity ratio has a decided influence on recovery efficiency and zone stability. The results also show that use of a suficieno zone size, even though the system has poor phase characteristics, yields higher oil recoveries than are obtained from straight water floods. Length-of-travel studies showed a square root relationship between zone growth and path length for favorable viscosity ratios. No such clear-cut dependence was observed under unfavorable viscosity conditions. INTRODUCTION As new oil reserves have become increasingly more difficult and expensive to find and develop, the oil industry has devoted more and more time and money to finding more efficient methods for exploiting known reserves. The increasing number of water floods is one manifestation of this attempt to improve oil recoveries from existing fields. Since considerable quantities of oil are by-passed by the waterflood process, it is only a partial answer to the problem. The search continues. Of late, several proposed processes have received the critical attention of investigators. Among them are gas drives, in situ thermal reactions and miscible displacements. The present paper is concerned with miscible displacements in conjunction with water floods. Recent literature1- reports that, under proper conditions, oil recoveries from LPG floods, propane sweeps, condensing gas drives, etc., approach 100 per cent of the oil in place in the region contacted by the flood. This literature also points out some of the problems associated with these processes, one of the main ones being the maintaining of miscibility. Compositional changes resulting from pressure and temperature variations or from zone dilution give rise to phase breaks and loss of miscibility, the conclusion being that, after loss of miscibility, much of the beneficial influence of the zone is lost.' The results of the subject work show that, if sufficient zone material exists ahead of a phase interface, considerable improvement in oil recovery can be obtained. In order to increase our understanding of the behavior of miscible systems as they degenerate into immiscible processes, a laboratory system having rapid deterioration characteristics was needed. The fluid system oil—ter tiary-butyl alcohol (TBA)—water possesses these properties and was the system investigated. Although these fluids are different from those generally employed in miscible studies, an understanding of their behavior can be applied to other miscible slug processes. However, under conditions where mass transfer maintains a miscible system through multiple contacts, e.g., enriched gas drive or high pressure gas drive, the observed behavior of alcohol zones would not be applicable. The variables of interest were zone size, viscosity ratio, length of travel, initial water saturation, rate and core characteristics. Of these, only the effects of the following on zone breakdown and oil recovery are reported in detail: (1) zone size, (2) path length, and (3) initial water saturation. The effects of viscosity ratio and core characteristics are discussed in conjunction with other variables. Although initial water saturation is not envisioned as important to the phase behavior of hydrocarbon systems, e.g., LPG, it is important in alcohol systems. The properties of the fluids and cores used are given in Table 1. As previously stated, this fluid system was selected because of the limited range of miscibility

By C. D. Stahl, E. E. Templeton, R. F. Nielsen

It has been customary, in predicting saturation changes, to use the Leverett fractional flow formula", obtained by eliminating the unknown pressure gradient from the generalized Darcy equations for the separate phases. The formula presents difficulties in the case of counterflow, since the "fractional" flow may be negative, greater than unity, or, in the case of a closed system, infinite. Recently, it has been shown by several authors that the corresponding equations (with capillary pressure and gravity terms) for actual flow of the phase may be used just as well. These equations are in agreement with Pirson's1 statement that, if the two mobilities differ considerably from each other in a closed system, the flow is largely governed by the lower value. The present study was undertaken because of an apparent lack of experimental data on gravity counter-/low with which to test the theory. A 4-ft sand-packed tube in a vertical position was employed. Electrodes for determining saturations by resistivity were spaced along the tube, one phase being always an aqueous salt solution. Air, heptane, naphtha, or Bradford crude oil was used for the other phase. A reasonably uniform initial saturation was set up by pumping the phases through the system, alter which the tube was shut in and saturation profiles obtained at definite intervals. Cumulative flows over certain horizontal levels were obtained by integration of the distributions; hence, differentiation of the cumulative flows with respect to time gave instantaneous flow rates. To compare experimental and theoretical flow values, capillary pressures were assumed given by the final saturation-distribution curve. The upper part corresponds to the "drainage" region and the lower part to the "imbibition" region, where trapping of the nonwetting phase occurred. While calculations indicated that the capillary pressure saturation function and, probably, the relative permeability saturation functions changed during the segregation, the relation of the measured rates to saturation distributions are in general accord with the frontal-advance equation. It appears that the Darcy equations, as modified for the separate phases, are generally valid for counterflow due to density differences. The usual method of predicting saturation changes, which involves a continuity equation and the elimination of the unknown pressure gradient from the flow equations, should therefore be applicable. However, the need for advance knowledge of drainage and and imbibition "capillary pressures" and relative permeabilities during various stages presents difficulties. INTRODUCTION The present study was undertaken because of a seeming lack of experimental data relating to vertical counterflow of fluids of different densities in porous media. In particular, it was desired to determine whether data obtained from these laboratory tests were in accordance with certain mathematical treatments of counterflow which have been proposed. The gravity "correction" has been incorporated into the flow equations (and, hence, into displacement theory) nearly as long as both have been used. field4 and laboratory5 data have generally borne out the validity of the theory as applied, for instance, to downward displacement by gas, with all fluids moving downward. However, the modifications for counterflow have only recently been pointed out. 2-3 It has been customary to use fractional flow rates instead of actual flow rates in displacement calcuIations. In the case of counterflow, this results in negative values, values greater than unity and, when rates are equal and opposite, in infinite values. As pointed out by Sheldon, et a1,3 and by Fayers and sheldon,2 actual flow rates may be used just as well. The fact that these may be of opposite signs for the two fluids does not present any difficulty.

THE Institute of Metals Division opened its series of meetings by a session* on lead, R. S. Dean be-ing in the chair and G. 0. Hiers acting as vice-chairman. A large and representative audience listened to the papers in the abstract and contributed an inter-esting and fruitful discussion. The main points of these papers and discussion are given below: In the absence of Carl E. Swartz, the summary and conclusions of his paper, "A Study of the Lead-Tin-Cadmium System with Reference to Their Use as Solders," were read. Swartz investigated a number of alloys in the lead-tin-cadmium system and prepared a diagram representing the solidification ranges of these alloys. He also made tensile strength tests of joints made with these alloys, and compared these with joints made with ordinary lead-tin solder. The tests showed solders containing cadmium were equally strong as the lead-tin series and that the cadmium alloys were suit-able in other respects for use as solders. In general, solders of the composition near to the ternary lead-tin-cadmium eutectic appeared to be the best for most soldering work although compositions widely differing are desirable for special purposes. The lead-tin-cad-mium solders are finding a market particularly in the fields requiring lower solidification temperatures than common solders. Mr. Darby opened the discussion and asked whether it was a fact that the lead-tin-cadmium solders were more useful than ordinary solders on galvanized and tin-plated sheet. C. Smith said he thought it to be a fact that galvanized sheet was more easily soldered by the lead-tin-cadmium solders than common lead-tin-solder. Continuing, Mr. Smith showed lantern slides of his own investigation of the thermal diagram and recommended the 70 per cent lead, 20 per cent cadmium, and 10 per cent tin for general employment. He thought the author did not differentiate between wetting and alloying and pointed out that wetting was more a ques-tion of the flux than the metal. In some cases a definite alloy was formed by soldering and in some no evidences of alloying were found. Illustrating the former case he showed slides and demonstrated that failures always took place longitudinal with the brittle compound alloy and transversely across the solder itself.

Jan 3, 1928

By G. Sachs, Jr. Brown W. F., Ebert L. J.

It is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to 'the same strength level (i.e., the same tensile strength in a conventional tensile test). However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features—the high speed, the notch, and the bending—the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests. In an attempt to analyze the fundamental nature of this test, it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom. The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension. This triaxial stress state occurs at a point in the interior of the notch specimen. It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present. This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors. This is contrary to the behavior. of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1947

By Ebert L. J., G. Sachs, Jr. Brown W. F.

It is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to 'the same strength level (i.e., the same tensile strength in a conventional tensile test). However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features—the high speed, the notch, and the bending—the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests. In an attempt to analyze the fundamental nature of this test, it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom. The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension. This triaxial stress state occurs at a point in the interior of the notch specimen. It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present. This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors. This is contrary to the behavior. of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1947

By Chester O. Ensign

Many publications to date have advocated under- seas mining operations, optimistically overlooking the paucity of information on mineral distribution and the ocean environments in which minerals occur. Such articles (smattered with opinion, as is this article) are herein tempered by my more conservative views on the economics of mining under the seas. For purposes of this paper, underseas mining refers only to the deeper surficial deposits of the continental shelf and the deep sea floor, i.e., the deposits of phosphorite and manganese nodules.

Jan 9, 1966

By Gordon S. Duncan

(New York Meeting, February, 1912 THE U. S. Geological Survey, I believe, has almost completed a study of the Harney Peak quadrangle, preliminary to the publication of a report on that, district. As I was engaged for some months on an investigation of the mode of occurrence of the ore-bearing formation in this area, it has seemed to me timely to make public the results of my study, as a contribution to the consideration of this subject. It seems scarcely necessary to describe the locality and general geology of the Black hills of South Dakota, for since 1846 many have contributed information concerning this region, some of the reports bearing such well-known names as those of Walter P. Jenney, Henry Newton, S. F. Emmons, and C. R. Van Hise, while we have only to glance at Bulletin No. 4 of the South Dakota School of Mines, in which Prof. C. C. O'Harra, of that institution, has given us a bibliography of contributions to the geography and geology of the section, to find that other well-known men have studied the district, and have given us the benefit of their researches. The U. S. Geological Survey has made geological maps of nearly the whole of the Black hills, the only quadrangle yet to be completed being, as stated, the Harney Peak district. During the late summer and autnmn of 1910, it was my lot to examine and report. on a considerable area in this neighborhood, which once had been prospected, and in some cases exploited, for tin. This paper gives an account of certain geological phenomena, noted at that time, which greatly influenced my conclnsions. The predominating formation of the district is pre-Cambrian, represented by a highly-cleaved mica-schist, usually very garnetiferous, and sometimes hornblendic. Rising like an island from the surrounding schist is a large mass of granite, known as

Jul 1, 1912

It is always the case with heavy and cheap materials that the area within which they can be economically used depends upon the cost of transportation, and in those days of poor roads and no mechanical means of haulage on them, coal could only be moved a few miles from the mine by any other means than water. The need of better means of transport to the areas west of the mountains had been urged by Washington and many other leaders, but the first turnpike over the Alleghenies only reached the Ohio River at Wheeling, W. Va. in 1818. The James River and Kanawha road reached the Ohio in 1831, that from Winchester, Va. to Parkersburg in 1838, and the road through the Cumberland Gap was completed in 1797. None of these affected the coal industry excepting indirectly by building up some of the river towns which coal could reach. The inadequacy of roads alone to carry the traffic of the rapidly growing interior communities was demonstrated only a few years after the National Pike was completed, and in the early 1820's several of the states embarked upon the construction of a canal system, which had been under discussion for some years. The Erie Canal was opened in 1825 from Lake Erie to the Hudson River through New York; Pennsylvania, Virginia and Maryland had already started similar projects designed to bring traffic to their principal cities from the interior. The Pennsylvania Canal was started from Columbia, as a railroad extended from Philadelphia to that point, and it followed the Susquehanna and Juniata Rivers to Hollidaysburg; thence to Johnstown, a distance of 36 miles, where it consisted of partly railroad and partly inclined planes, the boats being hauled up, and lowered down the planes; from Johnstown the canal followed the Conemaugh, Kiskiminitas and Allegheny Rivers to Pittsburgh, 104 miles. Boats first reached Pittsburgh by this route in 1834. The Chesapeake and Potomac Canal followed the Potomac River from a point above Alexandria above the falls, to Cumberland. This canal was chartered in the eighteenth century and a portion of it was used by traffic in 1800. It was too small to be of much use and was abandoned, and later after many legal and financial vicissitudes was completed to Cumberland, traffic from there starting late in 1850. This date, however, was long after the Baltimore and Ohio Railroad had been completed to

Jan 1, 1942

By J. S. Marsh

The student of steelmaking is all too well acquainted with the fact that in many instances he must deal with data that in graphical representation exhibit the property most desirable in bird shot. This is scarcely mystifying, since the effort to establish one variable as a function of another is usually hampered by the simultaneous operativeness of two or three other factors that may be important. A large part of arriving at relationships that have the pleasing self-consistency of, say, precise measurements of thermal expansion, consists of determining what factors must be held constant-—an even larger part usually consists of collecting data for which those factors have been so maintained. It is not intended to imply that functional relationships in the physical chemistry of steelmaking are hopelessly obscure; on the contrary, it is merely necessary to be undisturbed by marked deviation of some points from a curve that otherwise makes sense. A reaction mechanism suggested by such a curve may call attention to hitherto unsuspected factors operative in the origin of the deviating points, and thus permit another step to be taken in the direction of fuller understanding. It is proposed, therefore, to suggest several empirical relationships. Even though the approach is not always rigorous, deviations caused by simplifying assumptions appear to be too small to obscure a provisional It has been appreciated for some time that the carbon-oxygen reaction in liquid steel is highly important. For example, Körber et al.,' in introducing a summary of their extensive work on steelmaking reactions, said: "... the far-reaching and truly dominating action of carbon upon the metallurgical reactions will be especially stressed ..." In "Basic Open Hearth Steelmaking"2 (hereafter BOHS, for simplicity), it is accepted repeatedly that the various slag-metal interactions are nearly always controlled by the carbon-oxygen reaction. Before further discussion of this reaction, however, it will be worth while to consider briefly the carbon-oxygen equilibrium. In BOHS (p. 483) it is stated that: When liquid iron is brought into contact with gases containing carbon monoxide it absorhs carbon and oxygen. Conversely the carbon and oxygen in the metal unite to form carbon monoxide which is evolved from the bath during the open-hearth boil or while rimming ingots are solidifying. . . . When the equilibrium pressure is one atmosphere the equilibrium-constant equation simplifies, on the assumption that the activity of each element is equal to its percentage, to a constant which has been so much used that it has acquired a special symbol m. where m = %C X %O

Jan 1, 1945