Search Documents

By L. A. Rapoport, W. J. Leas

As a preliminary, consicleration is given to the conventional definition of relative permeability and to the conditions governing the simultaneous flow of oil and gas through porous media. For the conditions of flow prevailing throughout most of a gas drive reservoir, the oil and gas can reasonably be supposed to be in capillary equilibrium with each other. Under these conditions, and these conditions only, the relative permeability to liquid can be expressed as a function of saturation. The relative permeability to liquid in that case is dependent upon the distribution of fluids which itself is shown to be related to the capillary pressure, and, in turn, to the saturation. As a consequence, relative permeability to liquid can be expressed in terms of the volume and surface area of a network of liquid channels bounded by the rock and the gas phase. While the volume of this network can be evaluated accurately, the surface area cannot. However, for any such volume, maximum and minimum values of the corresponding surface area can be calculated from capillary pressure data. It is then possible to establish for any saturation the limits within which the value of the relative permeability to liquid must lie. As a consequence of the theoretical development, the validity of an experimental method for measuring relative permeability to liquid which utilizes a stationary gas phase is demonstrated. In this method capillary barriers are cemented to the ends of the core sample to permit the maintenance of capillary equilibrium between the two phases. At the same time, this procedure eliminates undesirable secondary phenomena such as end effects, fissure effects, etc., the presence of which adversely affect the results of other laboratory methods. The results obtained by theoretical calculations, and experimentally, are discussed. In view of the overall precision that can presently be obtained in reservoir calculations, the agreement between the calculated and measured relative permeability to liquid data can be considered satisfactory. In conclusion, for reasons of economy and simplicity, the procedure of calculating limiting relative permeability to liquid curves from capillary pressure data is indicated for general engineering purposes. It is shown that the above procedure can easily be extended to the cases where connate water is present. Its use for reservoir studies is particularly recommended in conjunction with the method for measuring relative permeability to gas' which simultaneously yields the capillary pressure data necessary for the calculations. THEORETICAL Definition of Relative Permeabilities — Basic Equations for Heterogeneous Flow The equations by which the relative permeability concept is defined and upon which the formulation of all of the gas-oil flow problems rests at the present time are expressed as: V, = — Grad PL = — Grad PL ....(la) PL µL, k k KG VG = —K - Grad PG k- Grad Pc .... (lb) Mo where ,. and G refer to liquid and gas; V is the volumetric rate of flow per unit gross area. µ the viscosity, Grad P the potential gradient. and k the specific permeability of the porous medium.* (For horizontal flow, Grad P becomes the pressure gradient; otherwise, gravity must be included.) According to these expressions, each of the constituent phases is considered similar to a homogeneous system where the volumetric rate of flow is proportional to the pressure gradient, and for each of which the constants of proportionality, k, and kG, are termed effective permeabilities. by analogy to the specific permeability as defined by Darcy's law in its original form. In order to obtain a convenient basis of comparison, the effective permeabilities are referred to the specific permeability, k, of the considered porous medium, with the help of the relations: k1. = KI. k kQ = Kn k..........(2) K,. and Kr. are defined as the relative permeabilities to the liquid and to the gas phase respectively, and frequently expressed in per cent of specific permeability. It may be seen that Equations (1); which appear to be a direct generalization of Darcy's law, correspond to the assignment at any given time of a set of "local" permeabilities to each point of the porous medium, and represent in a differential form the two fluid flow system as a simple superposition of the individual single flow systems. The above interpretation implies that the effective or relative permeabilities are independent of pressure or rate of flow,

Jan 1, 1951

By D. T. Peters, J. C. Bisseliches, J. W. Spretnak

The pain boundary relaxation phenomenon in high-purity copper, 0FHC copper, and a precipitation-hardenable alloy o-fCu-2 uit pct Co has been studied by internal ,friction and elastic aftereffect techniques. The data were analyzed by assuming the broad distribution of relaxation times observed obeys a lognormal distribution law which enables calculation of the relaxation strength. Grain size had no effect on relaxation strength, although the peak width increased with increasing grain size and decreasing temperature. A double grain boundary peak was produced in high-purity copper by annealing to produce secondary recrystallization. The activation energy measured for 99.999 pct Cu is 37.5 * 3 kcal per mol and 46.5 kcal per mole for OFHC copper. A small peak in the Cu-Co alloy at about 220°C at 1 cps was deduced to be the grain boundary peak. Its height increased and its activation energy decreased with increasing aging time. Except for erratic peak positions the observations were consistent with the theory of pain boundary sliding. BEFORE the mechanism of the grain boundary internal friction peak in metals can be satisfactorily explained, the detailed characteristics of the relaxation process must be documented. Of interest are the effect of grain size on relaxation strength, the high-temperature background, and peak width and position. The effect on the grain boundary peak of a precipitate at grain boundaries and of the change in distribution of the particles with aging time must also be explained by any existing or forthcoming theory. The model which has received the most attention was proposed by KG' and zener2 and proposes that the anelastic strain results from sliding of adjacent crystals at grain boundaries. The sliding is limited by the interlocking of grain corners. It follows, according to this model, that the relaxation strength is independent of and the relaxation time is proportional to the grain size. The proportionality between grain size, D, and relaxation time, t, has been confirmed by K&' and Bisseliches . In this case, the internal-friction peaks of various specimens can be superimposed by plotting Q-' as a function of the parameter vD exp H/RT where v is the frequency and H the activation energy. However, the data of Starr et 01.' and Leak6 fit better to a parameter containing D to an exponent near two. A meaningful relationship is not always deducible from the shift of peak temperature with grain size. KG7 demonstrated that a twofold variation in grain size obtained by varying the amount of cold work followed by identical recrystallization anneals will cause a peak shift that is too large to be accounted for even by an exponent of two. Since the decreased grain boundary area existing with a larger grain size is exactly compensated for by an increased sliding distance, the relaxation strength should not decrease with increasing grain size. The height of the internal-friction peak has generally been observed to be rather insensitive to grain size as long as the average grain diameter does not approach the specimen diameter. Exceptions have been reported by Koster, Bangert, and Lang8 for copper, and by Leak6 for iron. The observations for copper could well have been confused by the presence df 0.3 pct0. The possibility that the peaks may simply be increasing in width with increasing grain size and that the relaxation strength, which is proportional to the area under the peak, may remain constant was not examined. his point has been checked in this investigation using high-purity copper. Atomic mechanisms to account for damping by sliding at grain boundaries have been proposed by KG7 and Mott. KG predicts the activation energy to be identical to that for self-diffusion. Mott's "island" model suggests the activation energy is nL where n is the number of atoms in an island and L is the latent heat of fusion per atom. Other authors have felt that a value equal to the activa-

Jan 1, 1964

By P. Greenfield, P. A. Beck

The phase is a hard and extremely brittle material with a tetragonal crystal structure, containing 30 atoms per unit cell' It occurs in many binary and ternary alloys of the transition elements. The existence of twelve a phases has been reported in binary alloys of metals from the group vanadium, chromium, molybdenum, and tungsten with metals from the group manganese, iron, cobalt, and nickel. It is a characteristic fact that the composition of the o- phases in the various binary systems is not the same. Rather, there is a gradual shift in composition, for instance in the series of chromium a phases, approximately as follows: CrMn,, FeCr, Cr3Co,. In recent years several ideas have been put forward to account for this variability of composition. SullyZ proposed that a was a type of electron compound, characterized by 1.7 electrons per atom in excess of the number required to fill the Pauling atomic orbitals. These excess electrons were supposed to just fill the first Brillouin zone of the u structure. However, later work indicated that the phase is ferromagnetic at low temperatures, so that a- is unlikely to be a full zone compound.~ Another proposal,* which is also based on the structure of the transition elements advanced by Pauling, and in fact leads to essentially the same a compositions as Sully's theory, suggests that the u phase is characterized by a constant number of electron vacancies per atom. The electron vacancy numbers N,. used were originally the same as those in the Pauling theory, but were later modified empirically vn order to bring about better agreement with data for the p phase in certain ternary systems. For alloys, N,, was calculated on the assumption of simple additivity from the electron vacancy numbers of the components, as follows: N,. = 4.66 (Mo + Cr + V) + 3.2 (Mn) + 2.2 (Fe) + 1.71 (Co) + 1.6 (Ni). On this basis a reasonably constant value of N, = 3.4 was obtained for all of the binary u phases and a fairly constant value of N,, = 3.1 for the various p phases. More recently, Bloom and Granta pointed out that a similar correlation with the total number of 3d and 4s electrons per atom is also fairly well fulfilled and concluded that no reference need be made to the Pauling theory. This proposal does not lead to the same binary a compositions as the one described above, so that the relative merits of the two proposals may be determined on the basis of direct comparison with experimental composition data. The purpose of the present paper is to provide such a comparison. Since the experimental data for the composition ranges of several of the known u phases were rather incomplete, it was decided to carry out new experimental determinations for many of the binary systems. Experimental Procedure The alloys were prepared by induction melting in recrystallized alumina crucibles, either in vacuum or in helium atmospheres. Some aluminum was picked up from the crucibles in the alloys of high vanadium content, but this was minimized by keeping the alloys in the molten state for as short a time as possible. The maximum aluminum impurity was 0.13 wt pct by chemical analysis, in an alloy containing over 50 wt pct V. In general, the as-melted compositions agreed accurately with those obtained by chemical analysis. In the case of manganese, however, losses inevitably occurred; consequently all manganese alloys were analyzed. Specimens of all alloys were annealed at temperatures ranging from 1000" to 1300°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. All manganese alloys were sealed in quartz tubes under vacuum before annealing. The specimens were held at temperature for between four and eight days before being quenched into cold water. Alloys were prepared for microscopic examination by mechanical polishing, usually followed by electrolytic etching. X-ray diffraction specimens were prepared by crushing the homogenized alloys, and by reanneal-ing the obtained powders in evacuated quartz tubes for a few hours at the temperature of the lump anneal. X-ray diffraction patterns were made with unfiltered chromium radiation, using an asymmetrical focusing camera of high dispersion. Using microscopic and X-ray techniques jointly, the accuracy

Jan 1, 1955

By Nicholas J. Grant, Hanna Ibach, Bill C. Giessen

The system Ta-Rh was investigated over the entire comnposition range using metallogvaphic and X-ray techniques as well as thermal analysis. Terminal solubility limits, solidus temperatures, and the crystal structures of two new intermediate phases were determined. There are five intermediate phases: o, tetragonal, isostructural with o(Fe-Cr); a1, orthorhomnbic : a2, orthorhombic, isostructural with CozSi; 0 3, a high -temperature phase of unknozun structure; and a TaRh3, cubic, AuCu3 structure. a, aL, a,, and a melt peritectically; and a TaRh, has a maximum melting point. Five peritectic and one eutectic reactions occur. THE Ta-Rh phase diagram has not been fully treated in the literature; however, two inter metallic phases have been described.&apos;-&apos; This study attempts to work out the diagram covering the details of phase boundaries as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by National Research Corp., Cambridge, Mass., and rhodium powder of 99.9 pct purity, supplied by Bishop Co., Malvern, Pa. Analyses as given by the manufacturers are presented in Table I. In addition to the spectroscopic analysis, an oxygen analysis has been made of the tantalum powder. After preliminary trials, the standard procedure employed in making the alloys was as follows (see Ref. 4 for further details). The powders were weighed, mixed manually, compacted under 16,000 psi, and arc-melted at not more than 500 amp under thoroughly titanium gettered welding-grade argon of 400 mm Hg pressure. The gettering process was repeated after each melt. It had been shown previously5 that under these conditions no oxygen pick-up exceeding 0.001 pct in a hafnium button could be detected. The buttons, ranging from 5 to 10 g in weight, were inverted or, if possible, crushed and remelted three times. Melting presented no difficulty, except for tantalum-rich al- loys, which showed considerable spashing during melting. The average weight loss of 1 wt pct rose to 2.5 wt pct in these cases. Subsequent melting, however, resulted in losses of less than 0.1 wt pct. The melts obtained frequently showed small in-homogeneities, mostly in the tantalum-rich part of the system below 25 at. pct Rh. This was not due to insufficient blending of the elements, but to crystallization taking place from the cooled bottom. This condition was not improved by further re-melting; therefore the following precautions were taken. Cross sections of as-cast buttons were made. For the investigation only buttons were used where these inhomogeneities did not exceed 1 at. pct (estimated from the amounts of haSeS resent). In addition, only the center portions of such buttdns were utilized to minimize errors. Smaller buttons showed smaller concentration gradients and were used as a check. Finally, all alloys were homogenized to eliminate coring (see below). After this, the error in alloy composition due to inhomogeneity was cl at. pct. In order to confirm the concentrations of the alloys and to provide an impurity check, wet-chemical analyses and oxygen-fusion analyses of four key alloys were carried out. The results, together with the concentrations as calculated with the weight balance method, are presented in Table 11. It was found that for three alloys the agreement is very good (< 0.2

Jan 1, 1964

By J. E. Burke, A. M. Turkalo

IN 1923 Desch¹ pointed out that the grains in a metal which is anisotropic with respect to its thermal coefficient of expansion would contract differently upon cooling, and that the stresses developed might approximate the plastic strength of the metal. More recently Boas and Honeycombe2-5 studied the behavior of several metals upon thermal cycling and observed that the stresses developed in arlisotropic metals are great enough to produce slip lines in individual grains and a roughening of the specimen surface. This phenomenon they have named "thermal fatigue." The mechanism they propose involves essentially a kneading of the grains, the deformation being alternately in compression and tension in a given grain as the temperature is changed in one direction and then the other. The present work was undertaken to investigate the possibility that an additional mechanism might operate to produce plastic deformation during thermal cycling—a "thermal ratchet" that depends upon a combination of grain boundary flow to relax the stress that develops between differently oriented grains upon raising the temperature and transcrys-talline slip to relax the oppositely directed stress which develops on lowering the temperature. Thus, thermal cycling should produce a nonreversible distortion such that certain grains will change shape differently from their neighbors with a simultaneous displacement being produced at the grain boundary. Temperature Dependence of Grain Boundary and Grain Strength The critical resolved stress for the initiation of slip in metal grains is only mildly affected by temperature." For example, in cadmium it decreases from 0.15 to about 0.05 kg per sq mm when the temperature is increased from 20° to 458°K and further temperature increase causes little further decrease. On the other hand, the work of KG1 indicates that the grain boundaries behave in a viscous fashion that can be described8 by the expression: t = BVexp(Q/RT) [1] t is the shearing stress on the boundary; B, a constant; V, the flow rate at the boundary; Q, the activation energy for grain boundary flow; R, the gas law&apos;s constant; and T, the absolute temperature. Eq 1 indicates that the stress necessary to cause a given grain boundary flow rate, V, decreases rapidly with increasing temperature. The value of the constant B is such that at sufficiently low temperature and ordinary strain rates deformation will occur preferentially by slip rather than by grain boundary flow. There is considerable evidence to indicate Consider the bicrystal shown in Fig. 1. In grain 1 the slip plane lies 45 " to the boundary while in grain 2 the slip plane is 90" to the boundary. The coefficients of expansion of the grains in a direction parallel to the length of the crystal are a1 and a, with a, > a2 for the orientations shown. The sequence of events that can occur upon heating and cooling this specimen is illustrated schematically in Fig. 2. Initially there is assumed to be no stress in the specimen (A). Upon heating, grain 1 attempts to become longer than grain 2, but is constrained by grain 2. Thus grain 1 is loaded in compression and grain 2 is loaded in tension, and a shearing stress is present across the boundary (B). As the temperature is increased, the stress will build up, and finally grain 1 will be plastically deformed by slip, since the greater stress is resolved on its slip planes. Any further heating will result in more slip and the stress will remain constant until some temperature T* is reached where the stress can be relaxed by grain boundary flow.† At this relaxation temperature (C) a step will appear between grain 1 and grain 2. Further heating above T* will cause grain 1 to become relatively longer, but no stress will appear because the grain boundary is too weak to support the stress (D). Upon cooling again, at T* (E), the grain boundary will again be able to support a shearing stress, and upon cooling further, grain 1 will be loaded in tension and grain 2 in compression (F). When the decrease in temperature below T* is sufficient to impose the critical shear stress upon the slip plane of grain 1, it will be stretched by slip.

Jan 1, 1953

By Margaret V. Doyle, R. W. Powers

INTERNAL friction measurements, carried out as functions of temperature, have been used extensively to obtain data on the mobility of interstitial impurities in the Group V metals, vanadium, colum-bium, and tantalum. For a given frequency of vibration, the internal friction peaks at a temperature which depends principally on the particular metal and interstitial impurity. Relaxation times and corresponding activation energies are determined from a knowledge of such peak temperatures for various vibration frequencies. These experimentally determined relaxation times are related to the average jump frequencies of the interstitial impurity atoms using the model of Snoek1 and can be related to macroscopic diffusion coefficients as shown by Polder.2 In these Group V elements, the impurity whose diffusion rate has been the hardest to pin down by the internal friction technique has been carbon. The experimental difficulties associated with carbon in these metals were not evident in the earliest investigation carried out by Ke on tantalum.3 The carbon peak was thought to occur near 140°C at 1 cps on the basis of the enhancement of the height of this peak measured on specimens which had been coated with colloidal carbon and heated in vacuo at 1200°C. Presumably on the basis of similar evidence, Wert identified a peak also near 140°C at 1 cps in columbium with the diffusion of carbon in that element." Later, the difficulties of admitting carbon into these metals without simultaneously introducing oxygen were pointed out by Ang and Wert- nd by Marx, Baker, and Sivertsen.6 The latter suggested that the peaks attributed to carbon in tantalum and columbium might arise from the presence of traces of oxygen, adventitiously absorbed during the carburization. Such suspicion was confirmed, at least in tantalum, when it was found possible to prepare C-Ta specimens without contamination by oxygen. Specimens sci prepared, aitnough high in carbon content, gave no evidence of a damping peak near 140°C.7 Recently, the authors were able to Show that carbon diffuses in tantalum at a rate only slightly slower than that for nitrogen.8 At 1 cps, the carbon peak lies at 34g °C, only a few degrees above the nitrogen peak at 341 °C. However, the two could be distinguished by a different stability with respect to aging at 400 °C and by a different dependence of peak height on solute concentration. On the basis of this experience with tantalum, it appeared worthwhile to search also for a carbon peak in columbium in the vicinity of the nitrogen peak." In this report, the location of the carbon peak in columbium is made known and its position relative to the nitrogen peak is compared with the authors&apos; previous findings in tantalum. In addition, a second source of internal friction seen only in specimens of very high purity is discussed. Columbium was obtained from the Fansteel Metallurgical Corp. as either 30 or 40 mil diam stock. The manufacturer gives the following analysis as typical of this material: 99.4 pct minimum Cb, 0.10 pct maximum C, 0.5 pct Ta, 0.04 pct Ti, 0.02 pct maximum Si, and 0.01 pct maximum Fe. Wires 13 in. long were degassed near 2200°C for 4 to 16 hr in an ultimate vacuum better than 2.10" mm Hg in an apparatus described previously.8 This treatment reduced the oxygen and nitrogen damping peaks observed in the as-received material to less than 0.0001 in Q-1 above background. The latter value varied somewhat from specimen to specimen in the range 0.0004 to 0.0008, depending chiefly on the wire diameter and the frequency of vibration. The high temperature evacuation left the specimen in a rather soft condition, the Vhn being reduced to 40 from a value near 121 in the as-received conGi~iur~. The gram size was about the diameter of the specimen. After outgassing, specimens were loaded with carbon by absorption of such hydracarbons as methane or ethylene. Carbon was also added to a few speclrnens by heating them at

Jan 1, 1958

By L. E. Young

MUCH has been said and written on this subject and probably little new can be said. However, the point of view of the operating company changes from time to time, and more stress may be laid upon a subject today than was done some years ago, and it is with this changing point of view that the following observations are presented: The writer wishes to limit the discussion to views of a company mining bituminous coal, particularly to what the production department expects of the college grad¬uate. In an editorial in MINING AND METALLURGY for February, 1929, entitled "Is. Mining Engineering Passing?" it is stated that: It is not by accident that mining engineering courses have been general rather than special and form even today the only general engineering courses widely offered and followed by engineering students.&apos;* * * even in this age of specialization, the mining engineers remain a body characterized particularly by broad knowledge.

Jan 1, 1929

By J. M. Uys, T. B. King

The solubility of water in silicate melts of various compositions was measured. The basicity of the silicate did not appreciably affect the water solu-bulity at low-base content (acid compositions). Near the orthosilicate composition the solubility increased with basicity for silicates in which the cation displayed a weak ion-oxygen attraction and apparently decreased for those in which the cation showed a strong ion-oxygen attraction; metasilicates of the former class dissolved more water than those of the latter. Temperature had little effect on water solubility. The experimental results are interpreted on the basis of two modes of solution, the contribution of one decreasing, and that of the other increas -ing, with increased melt basicity. In the former, solution occurs through interaction with doubly-bonded oxygen atoms and in the latter, through interaction with singly-bonded oxygen atoms, or, in very basic melts, through reaction with free oxygen ions. THE hydrogen content of a steel melt is in a large measure determined by water dissolved in the slag. In some glasses water may be a major cause of "seeds". Water vapor in the furnace atmosphere is the primary source in both instances. A knowledge of the mechanism of water solution in silicate melts should help in assessment of practical methods for its control in steelmaking and glass refining. Walsh et a1.l measured the water content, expressed as hydrogen, of 40 pct lime-20 pct alumina-40 pct silica and 62 pct manganese oxide-38 pct silica melts as a function of the steam partial pressure, in equilibrium with the melt. Tomlinson 2 and, also, Russell3 investigated this relationship for a molten 30 pct soda-70 pct silica glass. In all three investigations, the solubility of water was found to be proportional to the square root of the partial pressure of steam. Moulson and Roberts 4 confirmed this relationship for a silica glass. On the basis of the square root relationship, Tomlinson2 and Russell3 interpreted the solution reaction as "network-breaking", similar to that expected on the addition of metal oxides to silica. Walsh et al.&apos; postulated two possible modes of solution, one the mechanism suggested by Tomlinson and Russell and the other the reaction of the water molecule with an oxygen ion to form hydroxyl ions. These two modes of solution suggest opposite effects of melt basicity on water solubility. However, little appears to be known about the effect of melt basicity on water solubility. Walsh et a1.l found, in the lime-silica system, that the water content increased slightly with increased basicity. As these authors pointed out, this does not appear to be in accord with their further observation that slags containing little or no silica dissolve very little water. Kurkjian and Russell5 measured the effect of basicity on water solubility in alkali silicates in the composition range 15 to 45 mole pct alkali oxide. They found a minimum in the water content at about 25 mole pct alkali. This was interpreted on the basis of two concurrent solution reacZions; one in which solubility was proportional to the activity of doubly-bonded oxygen and, in the other, proportional to the activity of singly-bonded oxygen. The present work was aimed at establishing the effect of basicity on water solubility in silicate melts over as wide a range of compositions as practical. APPARATUS AND EXPERIMENTAL PROCEDURE The silicate melt was equilibrated with a "carrier-gas" of accurately known water content, quenched, and analyzed for water by a vacuum fusion technique. Some pertinent details of the equilibration procedure, analysis technique, preparation, and handling of the silicates are given below. Gas-Silicate Equilibration. The apparatus used to equilibrate the melt with the gas mixture was similar to that used by Walsh et al.&apos; but with some important modifications.6 Purification trains were provided for nitrogen and hydrogen; whenever air or oxygen was used as carrier gas the nitrogen purifiCation train was used with the copper furnace at room temperature. Gas flow rates were measured with capillary flow meters; bleeders filled with a mixture of dibromo and tribromo ethyl benzene (density about 2 g per cc) were used for convenience in controlling flow rates.

Jan 1, 1963

By S. J. Swainson

PHOSPHATE ROCK is a low- priced commodity. This fact has influenced the choice of mining and beneficiating methods to a greater degree, perhaps, than in most other low-grade mining operations. The fact that many yards of everburden and matrix must be stripped and mined per ton of salable "rock" produced and sold has necessitated he development of relatively simple btneficiating plants having high capacity and low capital and operating costs. The law of diminishing returns must always be reckoned with in phosphate mining and washing, and often recovery must be sacrificed in favor of costs in order to achieve the highest over-all economic efficiency. The phosphate-bearing formation, known as "matrix," is composed of (1) phosphate pebbles, which are somewhat rounded in shape and which vary in size from 1-in, to micron sizes, (2) rounded quartz grains usually smaller than 10 mesh, and (3) clay, of varying "stiffness," which is the binder of the matrix. The phosphate pebbles vary in hardness. Their color, which varies from white to black, is not a reliable indicator of the Bone Phosphate of Lime (B.P.L.) content of the

Jan 1, 1944

By R. W. Stormont, F. Wald

The phase diagram of the Pseudobinary section PbTe-Fe was determined. It was found to contain a monotectic and a eutectic reaction, the latter one taking place at 14 at. pct Fe and 875° * 5°C. The solid solubility of iron in PbTe was found to be 0.3 at. pct by electronmicroProbe analysis. No solubility of PbTe was detected in iron. Slight deviations from true pseudobinary behavior were found to occur in the range of - 5 to 10 at. pct Fe. In the course of a general investigation of reactions of various metals with lead and tin telluride,&apos; the lead telluride-iron system was reinvestigated. It had been established much earlier than iron does not chemically react with lead telluride but forms a eutectic with a melting point of 879" The eutectic composition or other related information has never been reported, but for a number of years iron has been in general use for contacting of lead telluride and lead telluride alloys for thermoelectric applications. It seems therefore desirable to clarify the exact constitution of the system to furnish a base for the long-term evaluation of bonds made between lead telluride and iron either by pressure contacting or by brazing methods. I) EXPERIMENTAL METHODS Lead telluride-iron alloys were prepared in 10-g charges, using premelted lead telluride. This material was prepared from high-purity, semiconductor-grade lead and tellurium obtained from the American Smelting and Refining Co. and described as 99.999 pct pure. The iron used was "Armco" iron; the major impurities found here were 0.02 pct C, 0.018 pct Si, and 0.015 pct Cr. All remaining impurities were less than 0.01, the total of all impurities not exceeding 0.15 pct. Charges were prepared in closed quartz arnpoules which were evacuated and in some cases backfilled with high-purity argon to retard excessive lead telluride evaporation and deposition in slightly cooler parts of the ampoule. For high iron concentrations, this can lead to total separation of the constituents, since the vapor pressure and the sublimation rate of PbTe are quite high.4 Nevertheless, since the ampoules are closed, no change in overall composition was expected and the nominal composition of all alloys was assumed to be retained. X-ray diffraction analysis, thermal analysis, and microsections were used in the evaluation of the alloys. The nature of the system was such that X-ray diffraction was not particularly helpful. It merely served to establish that at all concentrations PbTe and a! iron were in equilibrium at room temperature. Thermal analysis was carried out by taking direct temperature vs time curves on a Sargent recorder where a width of 10 in. was kept as 1 or 0.5 mv by use of an automatic bucking voltage network. Quartz ampoules with minimized dead space, coated with boron nitride and fitted with a thermocouple reentrant, were used as containers for the charge. At high temperatures and over long periods of time, boron nitride reacts with iron. For the thermal analysis runs, however, this was not significant. More significant was the fact that the vapor pressure of PbTe at some of the meas -uring temperatures apparently exceeded I atrn quite considerably. This, in some cases, caused the slightly softened quartz tubes to blow out if great care was not taken to contain them and minimize time and temperatures used. As containers pure nickel tubes were used which also served to avoid temperature gradients in the quartz ampoule. Nevertheless, the experimental difficulties at high temperatures were severe and the monotectic temperature could therefore not be determined accurately. In general, the accuracy reached by the thermal analysis setup in this case is *4"C as determined with gold, silver, and tin, under the conditions of analysis here. Inherently, the apparatus is capable of reaching accuracies better than i 1°C. Also, difficulties were encountered in microsection-ing. They were related to polishing, since it is rather difficult to avoid pulling the iron out of the weak and brittle lead telluride matrix. It proved best to follow a procedure where, after grinding to 600 grit on carborundum paper, a polish with 6 p diamond was used on nylon cloth. Finally, #3 "Buehler" alumina and an automatic polisher were used for -5 min only, to avoid relief. The best etching results were achieved with

Jan 1, 1969

By M. J. GAVEN

COMING over from the plant on the Denver and Rio Grande yesterday afternoon I was an interested listener to a smoking-room conversation that had to do with the experimental plant near Rifle. The people who were talking didn&apos;t know me and I didn&apos;t know them, but I learned quite a little. I understood that the plant would never operate; that it was not intended to operate; that the "oil trust" would keep it from operating; that our tramway had eaten up all our money and still was not working and would not work; that the plant was run by a bunch of kids, and that the superintendent was probably the biggest kid of the bunch. I plead guilty to the latter. But the people who were talking were misinformed. The plant is producing oil. The first sample of oil that came from our unit at the Bureau of Mines experimental plant at Rifle, Colo., was produced on Sept. 18, the first that came out of the condenser, and it is still coming. This sample of oil may mean to the United States what the first oil produced from the first well meant.

Jan 1, 1926

By AIME AIME

ON Thursday a most interesting symposium on "Gases in Metals" was held, with both morning and afternoon sessions. The morning was devoted principally to the considerations of the steel maker, the nonferrous field being taken up in the afternoon period. Dr. John Johnston, as chairman, introduced the subject with "A Short Analysis of the Gas-metal Problem and Its Practical Importance." He then introduced P. H. Brace who explained in considerable detail the various vacuum fusion and other methods in use at present, both here and abroad, in the study of "gases" in metals. He was fol¬lowed immediately by H. W. Graham on "The Effect of Oxygen in Steel." The papers elicited considerable discussion, the point being particularly noted by both Dr. Rawdon and Dr. Sauveur that a knowledge of "total oxygen" alone is not sufficient information for the metallurgist, distribution of oxygen being probably the more important. Dr. Johnston, in commenting on the lack of agreement among many of the methods now in use, such as the Ledebur and vacuum fusion, spoke of the contemplated plan of the Iron and Steel Division to have a number of standard samples analyzed by many laboratories by the various methods, the Bureau of Standards acting as a clearing house, so that more definite information may be obtained on the comparative accuracy of the method.

Jan 1, 1933

By James Aston

A PROPER consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. MANUFACTURE OF WROUGHT IRON The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identified with our modern "Age of Steel" is a relatively brief interval compared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man&apos;s needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the forerunner in principle of today&apos;s scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort&apos;s invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By William H. Spice

Drilling activities in South Central Texas for the year 1945 continued the steady increase over the past two years, while new fields discovered for the year included four new gas fields and one field extension. In the 30 counties included in this area, which comprises district No. 1, Oil and Gas Division, Railroad Commission of Texas, 141 exploratory wells were completed, compared with 61 drilled in 1944 and 29 drilled in 1943. Of these 141 tests, 55 were field well and 86 were wildcats; 38 were completed as oil wells, S as gas and gas-distillate producers, and 95 were abandoned as dry. Atascosa and McMullen Counties were the most active in the district, accounting for 73 of the wells drilled.

Jan 1, 1946

By K. A. Jackson, J. D. Hunt

A general theory for the growth of lamellar and rod eutectics is presented. These modes of growth depend on the interplay between the diffusion required for phase separation and the formation of interphase boundaries. The present analysis of these factors provides a justification for earlier approximate theovies. The conditions for stability of rod and Lanlellar structures are consitleved in terms of the mechanisms by which the structure can change. The mechanisms considered include both small adjustments to the lnnzellar spacing due to the motion of lamellar faults, and catastrophic changes due to instabilities. It is concluded that stable growth occurs at or near the minimum interface undevcooling for a gizierz growth rate. The conseqrlences of the existence of a diffusion boundary layer at the interface are discussed. The experimental results for the variation of growth rate, undercooling, and Lanzellar spacing are cornpared with the theory. We believe that the theory presented in this paper provides an adequate basis for understanding the complex phenomena of lanzellar and rod eutectic growth. The growth of lamellar eutectics has been the subject of several theoretical and many experimental studies. The foundations for the theoretical work were laid by zenerl and Brandt2 in their analyses of the growth of pearlite. Zener estimated the effect cf diffusion, and took into account the surface energy of the lamellar structure. He found that the lamellar structure could grow in a range of growth rates at a given undercooling provided the lamellar spacing was appropriate for the growth rate. Since pearlite grows with only one growth rate and one lamellar spacing at a given undercooling, there is clearly an ambiguity in the theory. Zener removed this ambiguity by postulating that the growth rate was the maximum possible at the given undercooling. He predicted then that the product of the growth velocity v and the square of the lamellar spacing A should be constant, i.e., A2v = const. Brandt2 started out by assuming that the interface between the lamellae and austenite was sinusoidal. Because of this, the ambiguity encountered by Zener did not arise. Brandt was able to obtain an approximate solution to the diffusion equation, but, since he did not take into account the surface energy, his considerations are incomplete. Tiller3 applied some of these ideas to the growth of eutectics, and proposed a minimum undercooling condition to replace the maximum velocity condition used by Zener. These conditions are formally identical. Hillert4 extended the work of Zener. He found a solution to the diffusion equation assuming the interface to be plane. Taking surface energy into account, and applying Zener&apos;s maximum condition, he was able to calculate an approximate shape of the interface. Jackson et al.5 used an iterative method employing an electric analog to the diffusion problem to refine the calculation of interface shape. It was found that the interface shape calculated from a plane-interface solution to the diffusion equation was negligibly different from the exact solution. The method provided an analog only for eutectics for which the volumes of the two phases are equal, growing from a melt of exactly eu-tectic composition. There has also been considerable experimental work on eutectics, Several experimenters8-10 found that A2v is constant as predicted by Zener.1 Hunt and chilton10 demonstrated that ?T/v1/2 is also a constant for the Pb-Sn system as predicted. Lemkey et al.11have recently found A2v to be constant for a rod eutectic. In the present paper, we present the steady-state solution for the diffusion equation for a lamellar eutectic growing with a plane interface, for the general case, that is, with no restriction on the relative volumes of the two phases, and with the melt on or off eutectic composition. A similar solution is also found for a rod-type eutectic. Expressions are obtained for the average composition at the interface and the average curvature of the interface. These equations for the average composition and curvature are similar in form to those derived by Zener1 and Tiller,3 and provide a justification for some of the approximations made by these authors. The mechanisms by which the spacing in a lamellar structure can change are considered. The important mechanism for small changes in lamellar spacing involves a lamellar fault. Examination of the stability of lamellar faults leads to the conclusion that the growth occurs at or near the extremum.* The insta- bilities which can develop in a rodlike structure are also discussed, resulting in the conclusion that this structure also grows at or near the extremum. Comparison of the conditions for rod and lamellar growth permits a prediction of the surface-energy anisotropy required to produce rods or lamellae for various volume-fraction ratios. The diffusion equation predicts the existence of a diffusion boundary layer at the eutectic interface unless the eutectic has 0.5 volume fraction of each phase and is growing into a liquid of eutectic composition. This boundary layer is such as to make the composition in the liquid at the interface approximately equal to the eutectic composition. This boundary layer permits changes in composition during the zone refining of eutectics. Photographs of the eutectic interface of a growing transparent organic eutectic system have been made. Both the components of this eutectic are transparent organic compounds that freeze as metals do.12 The in-

Jan 1, 1967

By J. G. Faller, L. P. Skolnick

The distribution of cobalt and vanadium over non-equivalent crystallographic sites in C14-type Zr(VCo), alloys has been investigated. An anomalous X-ray scattering technique developed by Skolnick, Kondo. and lavine7 by which the separation in the scattering factors of two similar atoms can be enhanced was employed. Six alloys spanning the pseudobinary section ZrV1.6Co0.4-ZrVO.6CO1.4 at 10pct steps showed a nonrandom compositionally dependent distribution. Specifically, at high vanadium content cobalt preferentially occupied sites of type (6h) and vanadium, sites of type (2a; at low vanadium content the reverse was observed. In addition to the distribution fraction the structural parameters x and z were obtained. There was no significant deviation of these parameters from those obtained in the ideal C14 structure. Certain suggestions are made to account for the observed nonrandomness in the distribution of atoms on the two types of sites. INTERMETALLIC compounds of formula AB2 iso-morphous with MgCu2, MgZn2, and MgNi2 are known as Laves phases. Because Laves phases exhibit high symmetry and coordination numbers, the highest possible for an AB2-type compound,1 they are among the most frequently observed compounds in nature. In recent years interest has centered about the purely transition metal Laves phases2-&apos; in efforts to understand the function of atomic size and electronic structure in the formation of these compounds. It has been observed that pseudobinary Laves phase systems often show a variation of structure across the phase diagram. Such a system is the ZrV2-ZrCo2 in which the structure varies from cubic MgCu2 to hexagonal MgZn2 to cubic MgCu2.4 Some understanding about the conditions under which the second modification is stable can perhaps be gained by studying the distribution of cobalt and vanadium atoms on lattice sites in the MgZn2 modification of the system ZrV2-ZrCo2. In both the MgZn2 and MgNi2-types there exist nonequivalent positions open to occupancy by the B element, whereas in the MgCu2 prototype all sites are equivalent. Skolnick, Kondo, and La-vine7 have developed an anomalous scattering technique suitable for this type of investigation. Whereas the influence of size on the formation of a Laves phase is well recognized, no substantial evidence has been put forth in support of the size ratio dependence of a particular prototype. Berry and Raynor8 suggested that RA /RB ratio does indeed affect the type of structure that is chosen, MgZn2 compounds tending to cluster about 1.225 while MgCu2 compounds were found at larger deviations from this ratio. Dwight,3 however, from a study of 164 Laves phases does not believe this generalization to be justified. Electronic effects are certain to play a part in the stability of Laves phases in general and in the choice of a structure type in particular. For example, size along would favor the formation of Laves compounds of Ti, Zr, Hf, Ta, or Nb as the A element with nickel or copper as the B element. The absence of such is attributed to an unfavorable electron : atom ratio by Elliott and rostoker.4 Early experiments of Laves and witte9 with pseudobinary and pseudoternary systems of the three prototypes established the dependence of crystal structure upon electron: atom ratios. They observed that the MgCu2 structure dissolved elements of higher valency until the electron: atom ratio of =1.8 was reached; the MgZn2 likewise dissolved elements of lower valency replacing zinc. witte,6 from calculations of the electron : atom volumes of Brillouin Zones, obtained limits of stability for the prototypes MgCu2 and MgZn2. Elliott and Rostoker4 used these limits with considerable success in the all-transition element Laves phases they investigated. According to witte,6 compounds between the electron :atom ratios of 1.80 and 2.32 were of the MgZn2 type; those above and below exhibited the MgCu2-type structure. On the basis of these limits and an assumed valency of zirconium based upon the near tetra-valence of titanium, Elliott and Rostoker obtained valencies for the first transition series elements. For the Laves phases with which this investigation is concerned, ZrV2 and ZrCo2, the authors calculated electron :atom ratios of 2.54 and 1.56, respectively. These ratios are for the MgCu2-type structure and straddle the stability band of the MgZn2 modification. One could, therefore, predict that a pseudobinary system ZrV2-ZrCo2 should pass through the MgZn2 modification in traversing the composition diagram from one end to the other. Implicit in this assumption is a smooth change of the electron: atom ratio from 2&apos;54 to 1.56. MOSS10 states that his finding the low temperature structure of ZrCr2 to be C15 instead of C14 alters greatly Elliott&apos;s valency of zirconium and hence the assumed valencies of the other metals. Such a quantitative correlation of structure with electron : atom

Jan 1, 1963

By J. R. Schneider

INTRODUCTION Landowners in Texas for many years have freely granted, reserved and leased "oil, gas and other minerals" or interests therein. In recent years we have witnessed much litigation concerning what sub- stances should be included as "other minerals" within the phrase "oil, gas and other minerals," and this question has received the attention of numerous legal scholars. At the South Texas Uranium Seminar held in Corpus Christi, Texas, in September, 1978, Mr. William R. Dodson presented a paper dealing with this very subject and entitled "Uranium - Mineral or Surface? Who Owns It?" In his paper, Mr. Dodson reported on two recent Texas Supreme Court decisions, Acker v. a, 464 S.W.2d 348 (Tex. 1971) and Reed v. Wylie, 554 S.W.2d 169 (Tex. 1977). which held that the particular substance in question in each case is not a mineral within the phrase "oil, gas and other minerals" if substantial quantities of the substance lie so near the surface that production will entail the stripping away and substantial destruction of the surface. Since that time another chapter has been written in the Texas saga of "When is a Mineral not a Mineral?" and it is the intent of this paper to present an update of the Texas law. A review of the early Texas cases so ably covered by Mr. Dodson in his paper will not be repeated, except as is necessary to illustrate the evolution of the legal doc- trine which has been so aptly named "The Surface Destruction Test". BACKGROUND In order to appreciate the genesis of the problem, one must consider that oil and gas production commenced in Texas many years ago, Spindletop came in in 1901. As oil and gas became more valuable, land- owners with considerable frequency sold interest in the oil, gas and mineral estates in their lands, and reserved interest in the oil, gas and mineral estates in their lands when they disposed of their property. Due to the oil and gas background, and perhaps be- cause oil and gas was paramount in the minds of the parties, the traditional language employed in these grants and reservations was "oil, gas and other minerals" or variations thereof. There are literally hundreds of instruments employing this language constituting a link in the chains of title to thous- ands of acres of Texas land. In addition, there are thousands of acres of Texas land held by oil, gas and mineral leases, the primary terms of which have been perpetuated by production, containing similar language in their granting clauses. The severance of the mineral estate from the surface estate results in two separate and distinct estates, each having all of the incidents and attributes of an estate in land. with the surface estate being the serviant estate, and the mineral estate being the dominant estate and having certain easements in the surface estate to explore. produce and remove the minerals. Harris v. Currie. 176 S.W.2d 302, 305 (Tex. 1943). As observed by the court in the Harris case, this is because a grant or reservation of minerals would be wholly worthless if the grantee or reservor co~lld rwt enter upon the land in order to explore for and extract the minerals granted or reserved. Although the Texas law has recognized that an oil and gas lessee has the right to use so much of the surface as is reasonably necessary to produce the minerals. Warren Petroleum Corporation v. Monzingo, 304 S.W.2d 362, 363 (Tex. 1957), recent decisions of the Court have qualified this doctrine. In Getty Oil Company v. Jones. 470 S.W.2d 618 (Tex. 1971). Getty&apos;s pumpine, units were interfering with ones self-propelled sprinkler system utilized for irrigating the premises, and Jones sought to require Getty to install the-pumping units in cellars so that the sprinkler system could pass over them. In an effort to accommodate both the surface estate and the mineral estate, the court held (page 622) "...where there is an existing use by the surface owner which would otherwise be precluded or impaired, and where under the established practices in the industry there are alternatives available to the lessee whereby the minerals can be recovered, the rules of reasonable usage of the surface may require the adoption of an alternative by the lessee". Bearing in mind that the "reasonable use doctrine" grew up in the oil and gas industry involving sub- stances which can be produced by methods that do not destroy or deplete the surface estate, the question presented is whether the Texas courts will extend this doctrine to situations where claimants of "other minerals" seek to produce shallow deposits of iron ore, coal, lignite and uranium by surface mining methods which do destroy or deplete the surface estate? The surface destruction test has answered this question in the negative, at least as to iron. coal and lignite. However, the multitude of mineral estates in Texas which have been created by a grant. reservation or lease of "oil, gas and other minerals" will, doubtlessly, continue to fuel the fires of litigation. EARLY TEXAS DECISIONS In view of the evolution of the Surface Destruc- tion Test, an exhaustive review of the early Texas

Jan 1, 1980

By L. A. Cowan

IF the elements of personality be those characteristics in which humans differ, and if this definition be applied to the purchasing department for the Climax operations in Colorado, it must he concluded that this department has no distinguishing traits that would give it a departmental personality different from that possessed by the similar department of any progressive mining enterprise. Or, one may go further by stating that the rudimentary functions of any purchasing practice employed principally in the acquisition of maintenance, repair, and operating supplies are much alike, whether or not the industry involved be mining or milling. However, in the fact that the principal purchases of a mining company are materials for maintenance and repair and consumable operating supplies lies that essential characteristic which differentiates mining and milling purchasing functions from those of the manufacturer, the fabricator, or the ordinary processor.

Jan 1, 1946

By AIME AIME

COAL occupied a large place in the technical sessions of the Institute at its annual meeting for in addition to three sessions specifically de- voted to coal the two sessions on mine ventilation and the two on ground movement and subsidence, which are reported under their own headings, were primarily concerned with coal. The first session on coal was a joint one with the Iron and Steel Division, on Wednesday afternoon, with F. H. Crockard and J. R. Campbell presiding as joint chairmen and the latter actually officiating. The principal topic of discussion was G. S. Scott&apos;s paper "Evaluation of Coal for the Making of Blast- Furnace Coke," which has been published as T. P. 159. The author made a brief statement of its con- tents to start the discussion and the chairman, after briefly reviewing it himself, called on C. A. Meissner to start the discussion. He briefly reviewed the economic factors in the use of coal for coke-making, saying that not only .does the removal of 1 per cent of ash from the coal reduce the cost of pig iron 12 or 13c. per ton, but it also permits coke of satisfactory structures to be made from a coal which otherwise could not be used. He stressed the importance of uniformity in blast-furnace fuel and discussed the benefit of mixing different coals as raw material for the coke oven and cited experience with Illinois coals.

Jan 1, 1929

By D. E. Thomas, C. E. Birchenall

ALTHOUGH Eoltzmann gave a mathematical solution for the diffusion equation (for planar diffusion in infinite 01. semi-infinite systems only) in 1894 allowing for variation of the diffusion coefficient with a change in concentration, it was not until 1933 that this solution was applied to an experimentally investigated metallic system. The calculation was carried out by Matano&apos; on the data obtained by Grube and Jedele3 for the Cu-Ni system. Since that time concentration dependence of the diffusion coefficient has been demonstrated for many pairs of metals. However, the nature of this dependence has never been fully elucidated. Many investigators have suspected that these variations could be related to the thermodynamic properties of the solutions, one of the earliest explicit statements being contained in a discussion of irreversible transport processes by Onsager&apos; in 1931. Development along these lines has been greatly retarded by the lack of reliable data on the variation of tliffusivity with concentration, the paucity of the thermodynamic data for the same systems at the same temperatures and compositions, and an incomplete understanding of the relation of the thermodynamic properties of the activated state for diffusion to the bulk thermodynamic properties. The last factor has been discussed by Fisher, Hollomon, and Turnbull.5 In many instances where data exist, it is difficult to know which are acceptable. This problem probably applies more strongly to diffusion data than to activity measurements. For instance, four sets of observers"-" have reported self-diffusion coefficients for copper. The average spread between extreme results is a factor of about four, though the individual sets of data are self-consistent to about 20 pct. Thus one or more factors are out of control, at least in these experiments, making estimates of internal error unreliable. The most reliable diffusion data in most systems have resulted from the use of welded couples with a plane interface from which layers for analysis are machined parallel to the interface after diffusion. The layers are analyzed, and the result is a graphical relation between distance and concentration, usually called the penetration curve. Given the same set of analytical data and distances and following the same procedure in computation, different observers will generally produce diffusion coefficients which vary appreciably, especially at the extremes of the concentration range. Experiments must be carefully designed so that the precision is good enough to answer a particular question unequivocally. In the first calculation of the dependence of the diffusion coefficient on concentration in the metallic solid solution Cu-Ni, Matano found that the coefficient was insensitive to concentration from 0 to 70 pct Cu, after which it rose more and more steeply to some undetermined value as pure copper was approached.&apos; The same behavior was reported for Au-Ni, Au-Pd, and Au-Pt.* The data used were those of Grube and Jedele which were very good at the time, but are not considered particularly good by present standards. Furthermore, the method of calculation makes the ends of the diffusion coefficient-concentration curve unreliable. For better reliability, the high copper end of the curve has been checked by incremental couples, where the concentration spread is 67.7 to 100 atomic pct Cu. The implication of the curves calculated by Matano was that diffusion is very concentration sensitive in one dilute range of this completely isomorphous system and hardly at all in the other. Matano&apos;s result is confirmed. Later Wells and Mehll0 published data on diffusion in Fe-Ni at 1300°C, which represent a thorough test of the shape of the concentration dependence curve. They ran couples with the following ranges of nickel concentration: 0-25 pct, 1.9-20.1 pct, 0-20.1 pct, 20.1-41.8 pct, 0-99.4 pct, and 79.3-99.4 pct. Although the trend of the data indicates an S-shaped concentration dependence, their curve was drawn to the pattern set by Matano. Their original data have been recalculated for the 0-99.4 and 79.3-99.4 pct couples. Wells and Mehl&apos;s points and two independent recalculations from the raw data are plotted in Fig. 1. What appears to be the best curve is drawn through them. This curve shows little sensitivity to composition in both dilute ranges with a strong dependence at intermediate composi-tions.? Similar experiments on the Cu-Pd system are reported here at temperatures where solubility is unlimited. These lead to the same type of concentration dependence for the diffusion coefficients as was found upon recalculation of the data for the Fe-Ni system. Experimental Procedure Cu-Pd: The concentration dependence of the diffusion coefficient may be determined by the use of

Jan 1, 1953