Search Documents

By Reinhardt Thiessen

In the general study of coal, all evidence points in the one direction —that coals had their origin in a manner analogous to that of peat. The best method of studying coal, whether it concerns its chemistry, composition, or physical condition, is to study peat. The essentials in a study of peat are a knowledge of the chemistry of plants, knowledge of decay and of the transformation process of plant-substances into peat. A number of facts must be emphasized, namely, (1) peat is formed under wet conditions only; (2) plants grow in the place where peat is formed; (3) all the plant substances go into the bog; and (4) all the plant substances are subjected to a series of phases of decay which are (a) in the air completely above the water level but in relatively moist conditions; (b) above the water level, but covered by debris; and (c) completely submerged by both water and debris. Plant Chemistry Plant chemistry as a whole is remarkably well understood. The number of compounds composing plants is large, and it is not possible here to give even a comprehensive outline, but a classification into definite groups is possible; this is as follows: Carbohydrates; glucosides; pigments; tannins; acids, alcohols and ketones, etc., and their salts; essential oils; resins; vegetable bases; proteins; enzymes. Plant substances may also be grouped according to the role they play in the life of the plant, such as: Framework materials, living materials, food materials, protecting materials, waste materials. While this classification groups them well for. certain purposes, it does not group them exactly chemically; but in a consideration of the composition of coal, this is an excellent classification for our purpose here.

Jan 1, 1925

By J. B. STEWART

T HE position of each hole of any series of holes was carefully located by the surveyor, plotted in plan and elevation, and numbers assigned to them. The second series was staggered halfway between the first and so on for each succeeding series. Two and a, half to three months was frequently required to grout a series of holes calculated to insure safety for sinking a distance of 10 meters or say 33 ft. Naturally the initial operation called for drilling and grouting two series of holes but thereafter each sinking campaign required only one series of holes as shown in Fig. 8. The pump handling about 75 gal. per minute corresponds to 46 tons of grout or 6 tons cement delivered as a fair over-all average for the 24 hours. Thus 600 to 800 tons of cement was used for a single section of 33 ft. depth of shaft. One campaign used nearly 1100 tons of cement. Some holes were effectually sealed with as low as 30 tons, while many required 60, and some 80 to 90 tons.

Jan 1, 1926

By E. W. Engelmann

RAPID progress has been made during the past year in the copper mills throughout the country. Particular efforts have been made to increase the fine-grinding efficiency by the installation of larger classifying units operating in closed circuit with ball mills, such as the 78-in. high-weir Akins installation at the Phelps Dodge plant at Ajo, Ariz.; also the Type "FX" Dorr classifiers of Nevada Consolidated at McGill. Nev. and the "FX" Dorr bowl classifier of the Braden Copper Co. in Chile. Some of the copper milling plants in the Southwest, such as Chino in New Mexico and Ray Con. in Arizona, have replaced rolls operating wet in their fine-grinding circuit by rod mills. At Hollinger primary rod mills were formerly used in open circuit followed by pebble mills in closed circuit with classifiers. They now have primary ball mills in closed circuit with large extra heavy classifiers and no secondary mills. This new installation is producing the same grinding on 5000 tons per day with a reduction in cost of nearly 4c. per ton. At the Braden plant, in Chile, short-head Symons crushers have replaced 54-in. rolls, thereby in- creasing crushing capacity with some saving in maintenance cost.

Jan 1, 1939

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received' little study on the part of wire mills, particularly those that have commenced operations in the last few years.

Jan 1, 1930

By Leo H. Duriez, James V. Neuman

THE Bayard property of the united States Smelting Refining and Mining Company is in south central Grant County in southwestern New Mexico about fifteen miles east of Silver City and one mile west of Santa Rita. The present holdings cover a belt roughly one mile wide by ten miles long, lying west of, and adjacent to, the holdings of the American Smelting and Refining Co., Kennecott Copper Corp., Empire Zinc Co., and Peru Mining Co. The area extends from the village of Bayard on the south to a point three miles northeast of Fierro. The property is a part of the well-known Central mining district which has been New Mexico's leading copper-zinc producer for many years. The property is segregated into three sections, the Bullfrog, Hanover Bessemer, and the Shingle Canyon sections. Of these, the Bullfrog section covers the area between the towns of Bayard and Hanover and includes the Bullfrog No. 1, Bullfrog No. 2, Slate, Hobo,

Jan 1, 1948

By Louis P. Gignac

INTRODUCTION The selection of trackless equipment for underground mining can be a complex engineering problem due to the wide range of equipment sizes and operating modes. Computer simulation is particularly useful in estimating the performance of different systems for specific rock- handling problems. A hybrid simulator, incorporating some of the features of deterministic and stochastic simulation, was developed in order to handle not only queuing delays at loading and dumping points, but a1 so traffic interferences. Any number of vehicles can operate in any one of four basic modes (LHD, LAF, FEL, HFC) in parallel or in series. If the units use common roadways, loading and dumping points, certain operating delays will occur and be registered by the simulator and thus give a better evaluation of the marginal productivity of each additional unit. Based on a typical layout of drawpoints and ore passes for the sub-level stoping method, productivity and operating costs of different rock-handling systems will be examined. 1 . COMPUTER SIMULATION Numerous applications of computer simulations are reported in the 1iterature for various mining problems. Depending on the complexity of the system to be studied, simulation models were conceived with different degrees of sophistication. Three different types of simulators are generally recognized: stochastic, deterministic, and hybrid. Stochastic or Monte Carl o simulation randomly generates items, transactions, or events from some population defined by a frequency distribution and produces some expected future situations. Because this type of simulation is governed by the input of probability distributions, it requires a detailed knowledge of the system to be simulated; it implies expensive and time-consuming studies and reports to gene- rate this input information. A major short- coming of stochastic techniques is in new equipment evaluation, where the lack of data is unavoidable, and in new system design where the conditions are outside the range of the known historical behavior of the equipment. However, probabilistic simulation is almost essential for the study of cyclic queues and traffic problems. Deterministic simulation studies a system by generating performances on the basis of the mechanical capabilities of the vehicles and the physical limitations of the mining scheme. It is based on the engineering principle that the engine converts its energy into a rimpull at the wheels, which is in turn opposed by the rolling resistance and the grade of the ground; the machine is accelerated or decelerated until the tractive and resistive forces are in equilibrium, at which point it moves at constant speed. The information required by this technique, such as rimpull charts and equipment weight, is readily available from equipment suppliers. However, equipment performance at the mining site is also dictated by human and environmental conditions and changes with time and usage. For this reason, deterministic simulation generally overestimates the system capabilities; these must then be adjusted by efficiency factors based on observation and experience. Recently, hybrid simulation models, using both stochastic and deterministic techniques, have been built with some of the events generated stochasticly and others being deterministic. This compromising approach originated at the Pennsylvania State University. O'Nei1 (1966) designed a simulator for truck-and- shovel operations that allows for transportation from multiple faces to mu1tiple destinations. Each truck performs according to its mechanical capabilities while its loading and dumping time and its load fluctuate according to specific probability distributions. A major advance in the simulation of mining systems is due to Sanford's model (1969) of underground coal mining operations. The originality of the model is in the use of an Executive System Control which sets up the initial system, de- fines the operation conditions , and instructs continuously four sub-assemblies representing shuttle cars, trains, continuous miners , and conveyors, which in turn generate a feed-back of their movement to the Executive Control System for further instructions. The model has enough flexibility to simulate simultaneous and sequential jobs that characterize any dynamic system. Sanford's early work evolved slowly to what is known today as the Under- ground Materials Handling Simulator for coal mining (Manula, 1974).

Jan 1, 1981

By Sherwin F. Kelly

THE geophysical scene shifts and alters, the emphasis changes, and new possibilities loom, but the tendency is always towards widening the field and deepening the analytical penetration. Seismic methods have had their heyday, the torsion balance is being displaced by the gravimeter, electrical methods are showing deeper penetration, soil analysis is the newest tool, and gamma-ray logging appears on the horizon. One of the striking features of re- cent geophysical work in the oil fields has been the marked decrease in the number of seismic crews employed. Although the percentage of company crews is believed to have increased appreciably. the sum total has fallen sharply, as shown by the figures for the Gulf Coast area. About two years ago probably over 100 seismic parties were operating there, whereas now there are only about 35. This decrease may be partly due to the low prices of petroleum with a consequent reluctance to spend money to increase crude-oil re- serves but more probably to the fact that reflection and refraction shooting have been carried on so extensively that they have been applied to a large pro- portion of the areas in which they may reasonably be expected to succeed. Some of the earlier enthusiasm, particularly over reflection prospecting, may have erred on the side of over- optimism; some of the present curtailment may be due to over pessimism; but in the opinion of various observers seismic work at the present rate seems to be at it- optimum. It nevertheless remains pre-eminent as a technique for detailing structures in areas where good reflections can be obtained and is the only method that will give accurate depth to definite beds. Results may be poor in certain areas but many regions still remain wherein it can be applied, so that plenty of structural mapping remains to be done by the reflection seismic method.

Jan 1, 1940

By C. S. Blair

The development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Alabama, in 1908 was an innovation probably unique for any mining organization south of the Ohio River. At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator difficulties in his future operations, which the latter had not anticipated. Eventually, however, the value of having these data became apparent to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1935

By C. S. Blair

The development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Alabama, in 1908 was an innovation probably unique for any mining organization south of the Ohio River. At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator difficulties in his future operations, which the latter had not anticipated. Eventually, however, the value of having these data became apparent to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1935

By AIME AIME

SOME 65 members of the Institute, including most of the Local Section delegates and several Directors and officers, were on hand for the Annual Business Meeting of the Institute held in the Engineering Societies Building on Monday, Feb. 21, at 4:30 p.m., immediately following the second session of the Local Section Delegates Conference. President Mathewson presided. The meeting was largely taken up with the presentation of committee re- ports, discussion of which was invited. F. E. Wormser presented the report of the Admissions Committee ; Philip Kraft, Papers and Publications Com-

Jan 1, 1944

By Dozier Fircley

SOME nonmetallic minerals and their products, such as portland cement, common brick and hollow tile, sand, gravel, crushed rock, vitrified salt-glaze clay pipe, and the like, are a necessity in every community. They are mineral in nature but the establishment of plants for their production is usually a local and elementary problem. Yet it is probable that an economic study of the problem in every locality will show that such nonmetallic mineral commodities are not always obtained in the most economical way, or in the best quality. Other nonmetallic minerals are of such value that they may be shipped for long distances and sold in sufficient quantities to establish prosperous commercial ventures. Among these are phosphates, barium compounds, borates, nitrogen compounds, magnesium compounds, sulfur, asbestos, and potash. Success in marketing such products depends on quality, production cost, transportation, and similar conditions.

Jan 1, 1932

By E. R. Helderman, C. Y. Ang, C. C. Nealey

Beryllium-base alloys have been successfully p7.-epared by the liquid-phase sintering technique. Depending orz the composition and amount of the intended liquid please, microstructures either single -phase or duplex in feature with randomly oriented grains have been obtained. Qualitative and semi-qualitative determination of distribution of alloying elements md microsegregations in some experi)uzental alloys haue been made by electron-micro-probe analysis in conjunction with microliardness testing and standard metallography. Tensile tests reoealed that some conzpositions possess attractive elastic properties with Young's mot1uli greater than 40 X 10' psi. In powder metallurgy, liquid-phase sintering is a process or phenomenon that has proven to be of practical value. For example, the heavy metals such as tungsten-copper-nickel, high-strength heavy gyro alloys,' heavy-duty electrical contacts,' and tungsten carbide tool materials are all products of liquid-phase sintering. Mechanisms involved in liquid-phase sintering, however, are not completely understood. Questions regarding the exact roles played by rearrangement of particles, liquid/vapor surface energy, solution and precipitation, and so forth, have not been completely answered. Evidence has been cited3 that at least volume shrinkage in the densification process is diffusion-controlled. It is possible that the predominant mechanisms for the complete densification and grain growth in a liquid-phase sintered system depend primarily on the alloy systems involved, in addition to processing conditions. Despite the lack of sound understanding of the mechanisms of the process, liquid-phase sintering has been and is being used to advantage either to synthesize microstructures for their special properties or to prepare alloys which are difficult to form by fusion process. Liquid-phase sintering of beryllium alloys was first attempted by Jones and Williams.4 They first tried infiltrating beryllium with magnesium, and then succeeded in preparing the alloy by sintering Be-Mg powder compact in molten magnesium bath. This investigation resulted in the identification of some Mg-Be intermediate phases. Crossley et a1.5 also used liquid-phase sintering technique in an attempt to produce ductile beryllium alloys for structural applications. The major liquid-phase components investigated by Crossley et al. were aluminum and silver with minor additives of germanium, calcium, lanthanum, cerium, and yttrium. The lack of wetting and the bleeding out of liquid phase were the difficulties encountered during experimentation. According to Hodge,6 the two compositions investigated by Crossley, which showed some promise based on compression tests, involved large amounts (over 35 wt pct) of silver, thus making them too heavy to be of practical interest to the aerospace industry and military users. The present investigation was prompted by the search for light-weight (density less than aluminum) beryllium alloys exhibiting small anisotropy in physical properties for precision inertial navigation instrument applications. In addition to isotropy, good structural properties such as high elastic modulus or desirable combination of mechanical and physical properties are also objectives of this investigation. The technique of liquid-phase sintering was chosen for its versatility in producing either duplex or homogeneous microstructures. This report is concerned with the use of copper and aluminum, with or without silicon addition, as the intended liquid phase, and the resultant micro-structures and some physical properties of the beryllium alloys. Qualitative and semiquantitative electron-microprobe analyses of some of the alloys are presented to illustrate the usefulness of this microanalytical technique for the identification of microconstituents and their distribution. EXPERIMENTAL PROCEDURES The beryllium powder used was -200 mesh Brush Beryllium Co. QMV NP-50 grade. Typical chemical analysis of the powder is shown in Table I. Commercial high-purity copper, aluminum, and silicon powders all screened to —100 mesh were used as additions. Mixed powder compositions were ball-milled in ceramic jars for 1/2 hr to ensure thorough blending. Milled powder was loaded either in 3/4-in.-diam button die or in Metal Powder Association flat tensile specimen die and compacted under top and bottom pressure. No lubricant or organic binder was used. Sintering was carried out in a quartz tube under a vacuum of 50 to 100 µ pressure. Surface hardness and some microhardness readings were taken on sintered specimens. Sintered density was

Jan 1, 1965

By C. J. Bauer

WHEN the pipe lines from the Middle East to the Mediterranean are completed, the Middle East supplies will relieve the strain on Western Hemisphere petroleum resources, part of which are now shipped for Eastern Hemisphere use. A sketch of the world petroleum situation as it appears today and in the immediate future will help in understanding the future place of Middle East oil supplies. Anticipated 1951 world demand is slightly under four billion barrels. To meet this requirement, crude output and refinery runs throughout the world (including Russia) must be increased about two million barrels per day above the average of 1947. This increment, together with pipe lines, tankers, and other facilities, will require in excess of ten billion dollars of new capital in the next four years. We are, therefore, looking forward to the greatest expansion program in the history of the industry.

Jan 1, 1948

By Rztssell H. Bennett

A SURVEY of the Mesabi Range iron-ore industry demonstrates that a satisfactory degree of technical progress has been achieved in the last fifteen years. This advance has not been made over a uniform front, but, by salients and bays, according to the different initial positions, economic and technical, of the component producing companies. The producers endowed with rich ore have in general, because of natural advantages, progressed more slowly than their neighbors with leaner properties. The advance has been made step by step all along the line -blasting, loading, hauling and concentrating-and without the benefit of radical innovation. There have been, for instance, no such parallel discoveries in iron ore as leaching and flotation in copper. The much lower unit price of iron operates, of course, to bar the application of these and other practices developed for the higher-priced metals. There exists, however, a radically new concentration process whose technology is well worked out and which may become economically operative in the not too distant future; this, as so often happens in engineering advance, because of recent developments in an entirely unrelated field. First, however, let me devote a paragraph or two to the more important economies effected in mining.

Jan 1, 1932

By Harry C. Wiess

RECENT announcement of further restrictions on gasoline consumption in the Mid-West and Southwest has focused public attention on current discussions of an oil scarcity. Conflicting arguments are advanced on the one hand that we have plenty of oil and will not need to restrict consumption as soon as transportation facilities are adequate, and on the other hand that a great impending shortage will require most drastic reductions in civilian consumption in order to provide adequate supplies for military purposes. Data can be presented to support both views, the result being that the public is confused and uncertain of where the truth lies. For a nation with about half of the known crude-oil reserves of the world and two thirds of the total production it seems almost incredible to the layman that any shortage can exist. Those familiar with estimates of future demand. however. show increasing concern regarding our ability to meet military demands without further restrictions in civilian use or wasteful production from our remaining reserves. Only by considering such facts as are available and can be made public can a true appraisal be made of whether or not we are faced with a shortage that will amount to a crisis in crude oil.

Jan 1, 1943

By J. C. Savins

The practical analysis of the hydrodynamics of the wellbore has long been a subject of interest to engineers. This paper presents a simplified solution to the problem of computing the pressure drop for the flow of drilling mud in the annulus of the wellbore. This solution is, however, an exact and rigorous solution under the assumptions which have been imposed. These assumptions are that the drilling fluid is a Bingham plastic fluid* and that the annulus is formed by two concentric, stationary, cylindrical pipes. It is further assumed that the fluid is incompressible and that its motion is isothermal and in a steady state. This problem under the same assumptions has been attacked by previous authors. Beck, Nuss and Dunn' proposed that the equation for the flow of a Bingham plastic fluid in a cylindrical pipe could be applied to an annulus if the pipe radius were replaced in the equation by the hydraulic radius. This equation, known as the Buckingham-Reiner equation' (see Appendix 1), was also used in an approximate form. Van Olphen pointed out that even for a simple or Newtonian- fluid the pipe equation (Poiseuille's law) could not be converted to the Lamb equation escriptive of flow in an annulus (see Appendix 1) by using the hydraulic radius. Van Olphen further attempted to give a solution for the annular flow of a Bingham plastic fluid by introducing approximations similar to those which have been used in the case of the Buckingham-Reiner equation. Other attempts to provide approximate or exact solutions have been made by Grodde' and by Mori and Ototakeq. The present authors some years ago in unpublished work derived the correct expressions relating the pressure drop and flow rate for this problem. It was found that the solution consisted of two simultaneous equations, one of which contained a logarithmic term. Thus, obtaining numerical results for any particular case of interest involves very tedious trial-and-error computations. Very recently Laird presented the correct derivation of the two equations which are given in full detail in Appendix 1. In order to reduce the amount of calculation time which would be involved in providing a complete tabular or graphical solution to the problem, a high-speed electronic digital computer has been utilized. For this purpose the two simultaneous equations were transformed into more compact expressions by introducing reduced variables. These expressions are given in the following theoretical section. A similar procedure in this problem has been developed by Fredrickson and Bird1" Their tabular results, however, are very incomplete in the range of practical interest for problems of wellbore hydrodynamics. We have furthermore been able to express our graphical results in terms of convenient and familiar dimensionless groups. THEORETICAL DEVELOPMENT Use of Reduced Variables In terms of reduced variables the two simultaneous equations just discussed take the following form, The reduced variables q, x, a and z are defined in terms of the various measured quantities, where Q is volumetric flow rate, AP/L is pressure gradient, Dl is OD of inner pipe, D, is ID of outer pipe, is plastic viscosity, and is yield point. Thus, we have a dimensionless volume flux, a dimensionless reciprocal pressure gradient, and the ratio of the pipe diameters Before introducing the fourth reduced variable, z, it is of interest to consider the physical significance of the parameter x. As may 'be seen from the velocity profile of Fig. 1 the Bingham plastic fluid has the interesting property that a portion of the stream flows at a uniform velocity without shearing action. This section of the stream is situated approximately in the center of the conduit and is known as the "plug flow" region. Its existence is due to the fact that the shearing stresses within the region do not exceed the yield point, which is one of the two flow properties characterizing the fluid. The parameter x then turns out to be the ratio of the

By Oliver Bowles

A HEAVY gel of bentonite clay has been proposed as an effective lubricant to speed down the ways to sea, river, or lake, the mighty cargo ships now hitting the water at the rate of about three a day. Another unusual application of a nonmetallic mineral is in food conservation, for the claim has been made that the next new item on the menu for poultry and rabbits will be vitamin tablets prepared from mont-morillonite clay. These uses have minor importance but illustrate not only the diversity in utilization, but the notable trend in 1942 toward mobilizing nonmetallic minerals for the war program. Although occupying less headline space than iron, steel, copper, aluminum, magnesium, and other metals, the nonmetallics are filling important emergency needs. Mica and quartz crystal are essential to communication; asbestos is urgently needed in fireproof heat and electrical insulation; and strontium minerals are utilized in the manufacture of signal flares and tracer bullets.

Jan 1, 1943

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.' It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anortho-site, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagio-clase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout.' Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized.V he bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15". The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1953

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.' It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anortho-site, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagio-clase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout.' Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized.V he bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15". The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1953

By Frances Hurd, Clark

Iv 1897, Roberts-Austen(l)$ found an arrest in the thermal curves of alloys of 60 per cent. copper and 40 per cent. zinc. This break occurred from 450° to 470° C. Shepherd, (2) working in 1904, was unable to detect any change in the direction of the thermal curve. In 1911, Carpenter and Edwards(3) confirmed the work of Roberts-Austen and called this a eutectoid transformation of beta to alpha plus gamma. Hudson') in 1914, showed that the beta constituent could be produced synthetically at temperatures below the transformation point. He believed the change in the beta was polymorphic in nature rather than a eutectoid. The work of Matsuda(32) in 1922 demonstrated this break by thermal analysis, microscopic investigations, dilatation, electrical resistance measurements, and a thermoelectric study. He believed the transformation to be continuous from 300° to 480° C., and comparable to the A 2 transformation in iron. Later, in 1924, Andrew and Hay, with electrical resistance measurements, confirmed Matsuda's work. Imai(28) showed the transformation to be progressive and therefore a function of the temperature rather than the time. He stated that it was neither a eutectoid nor an allotropic change of phase. Atomistically expressed, it was a change, not of atomic configuration, but of atomic energy of some kind; and again it was compared to the A 2 transformation in iron. Imai believed that his analyses by X-rays led to the same conclusion. In order to study this change, at 470'C., in homogeneous 60:40 brass, Homerberg and Williams «0> and Homerberg and Shaw(41) quenched their material in iced brine to obtain the beta solid solution and reheated at various temperatures. At 200° C., a change in the microstructure and physical properties occurred. A fine-grained structure, which they termed alpha and which had the appearance of a sorbitic steel, appeared, with an increase in the tensile strength to 82,750 lb. per sq. in., and a Brinell ball hardness of 240 with 3000 kg. load. At 470° C., the alpha

Jan 1, 1927