Institute of Metals Division - Microstructures of Liquid-Phase Sintered Beryllium Alloys

Beryllium-base alloys have been successfully p7.-epared by the liquid-phase sintering technique. Depending orz the composition and amount of the intended liquid please, microstructures either single -phase or duplex in feature with randomly oriented grains have been obtained. Qualitative and semi-qualitative determination of distribution of alloying elements md microsegregations in some experi)uzental alloys haue been made by electron-micro-probe analysis in conjunction with microliardness testing and standard metallography. Tensile tests reoealed that some conzpositions possess attractive elastic properties with Young's mot1uli greater than 40 X 10' psi. In powder metallurgy, liquid-phase sintering is a process or phenomenon that has proven to be of practical value. For example, the heavy metals such as tungsten-copper-nickel, high-strength heavy gyro alloys,' heavy-duty electrical contacts,' and tungsten carbide tool materials are all products of liquid-phase sintering. Mechanisms involved in liquid-phase sintering, however, are not completely understood. Questions regarding the exact roles played by rearrangement of particles, liquid/vapor surface energy, solution and precipitation, and so forth, have not been completely answered. Evidence has been cited3 that at least volume shrinkage in the densification process is diffusion-controlled. It is possible that the predominant mechanisms for the complete densification and grain growth in a liquid-phase sintered system depend primarily on the alloy systems involved, in addition to processing conditions. Despite the lack of sound understanding of the mechanisms of the process, liquid-phase sintering has been and is being used to advantage either to synthesize microstructures for their special properties or to prepare alloys which are difficult to form by fusion process. Liquid-phase sintering of beryllium alloys was first attempted by Jones and Williams.4 They first tried infiltrating beryllium with magnesium, and then succeeded in preparing the alloy by sintering Be-Mg powder compact in molten magnesium bath. This investigation resulted in the identification of some Mg-Be intermediate phases. Crossley et a1.5 also used liquid-phase sintering technique in an attempt to produce ductile beryllium alloys for structural applications. The major liquid-phase components investigated by Crossley et al. were aluminum and silver with minor additives of germanium, calcium, lanthanum, cerium, and yttrium. The lack of wetting and the bleeding out of liquid phase were the difficulties encountered during experimentation. According to Hodge,6 the two compositions investigated by Crossley, which showed some promise based on compression tests, involved large amounts (over 35 wt pct) of silver, thus making them too heavy to be of practical interest to the aerospace industry and military users. The present investigation was prompted by the search for light-weight (density less than aluminum) beryllium alloys exhibiting small anisotropy in physical properties for precision inertial navigation instrument applications. In addition to isotropy, good structural properties such as high elastic modulus or desirable combination of mechanical and physical properties are also objectives of this investigation. The technique of liquid-phase sintering was chosen for its versatility in producing either duplex or homogeneous microstructures. This report is concerned with the use of copper and aluminum, with or without silicon addition, as the intended liquid phase, and the resultant micro-structures and some physical properties of the beryllium alloys. Qualitative and semiquantitative electron-microprobe analyses of some of the alloys are presented to illustrate the usefulness of this microanalytical technique for the identification of microconstituents and their distribution. EXPERIMENTAL PROCEDURES The beryllium powder used was -200 mesh Brush Beryllium Co. QMV NP-50 grade. Typical chemical analysis of the powder is shown in Table I. Commercial high-purity copper, aluminum, and silicon powders all screened to —100 mesh were used as additions. Mixed powder compositions were ball-milled in ceramic jars for 1/2 hr to ensure thorough blending. Milled powder was loaded either in 3/4-in.-diam button die or in Metal Powder Association flat tensile specimen die and compacted under top and bottom pressure. No lubricant or organic binder was used. Sintering was carried out in a quartz tube under a vacuum of 50 to 100 µ pressure. Surface hardness and some microhardness readings were taken on sintered specimens. Sintered density was