Search Documents

By Ravi Shah, Augusto Lucarelli, Daniele Peila

"In mechanized tunneling the annular gap between the segmental lining and the surrounding soil caused by tunnel driving, must be backfilled almost instantaneously with an adequate grouting mortar. The objective of this research is to perform a fully three dimensional modeled parametric study using FLAC 3D and evaluate the effects of backfill grouting on the tunneling performance. The research focuses on comparisons between different injection materials and state-of-the-art Bi-Component grout and their effects on the settlements on the surface. The research consists of testing a regular situation of tunnel excavation using a shielded machine with face under pressure. The tunnel dimensions and the soil properties are selected as close as possible to the reality and based on Turin Metro case. 1 INTRODUCTION Excavation of tunnels in urban areas can induce ground movements, which have negative effects on existing structures. In such scenarios, shield tunneling has become a well-accepted construction method in various ground conditions. It is characterized by relatively complex interactions between the soil, the tunnel boring machine (TBM) itself, the tunnel lining and the tail void grout. The problem to control the settlement depends on the face pressure, ground properties and back filling procedure and material of the tail void. The face pressure acts against the front to guarantee the face stability. In case of EPB TBMs the stability of the tunnel face is ensured through the excavated soil itself, which is conditioned and is maintained in compressed state within the excavation chamber. When excavating with TBMs a tail void is created between ground and the lining (Fig.1) after the TBM excavation and ring assembly that must be backfilled instantaneously by injecting the backfill material through the TBM’s tail shield. The process is of primary importance as it reduces the surface settlements and creates an immediate link between the ground and lining, sealing against ground water and leakage, reducing the differential movements between segments and providing long-term stability. The most used backfilling materials are: Inert mixtures that do not contain cement instead sometimes they are replaced by fly ash or other substitutes. A typical design of an inert mortar consists of sand, fly ash, bentonite and water. Pea gravel, which is constituted of granular materials with grain size ranging from 8 to 12 mm. This mixture is highly recommended for tunnels being constructed in rock mass with little deformation rates.Cement mortar is composed of cement, water, aggregates and sometimes bentonite. Cement controls the principle mechanical property of the mix, which can reach high values of 15-20 MPa in 28 days. The aggregates contribute towards the shear strength and reduce the pumpablity of the mix (Thewes and Budach, 2009). The reduced active systems have a cement content of 50-100 kg/m3, whereas the active system the binder component derives full hydration with cement content of over 200 kg/m3 ."

Jan 1, 2016

By Xingang Wang

Spontaneous combustion is one of the most important safety issues in the global coal industry. It is considered to be a trigger for explosions in underground mines, especially for gassy mines. This thermal event is not easily detectable in the gob and sealed area. It is also a tough job to find the most likely hot point accurately. Admittedly, determination of the propensity for spontaneous combustion before mining activity should be a necessary step in the design of a mine and ventilation plan. However, due to the complexity of the chemical and physical properties of coal, spontaneous combustion has not been fully understood. According to a proximate analysis of coal, it is believed that sulfur and volatile matter in coal are the main intrinsic factors that cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal?s self-heating should be quantified. This study aims to improve the previous mathematical model developed by the authors for studying a coal?s propensity for spontaneous combustion. It enhances the model?s ability to consider the effects of sulfur, volatile matter and moisture content in the coal ? three important factors affecting a coal?s self-heating process. Based on the law of energy conservation, heat release rates for pyrite oxidation and moisture condensation are built into the model. Finally, the simulation results in terms of time versus temperature are calibrated with adiabatic testing data extracted from the literature for pyrite oxidation and moisture condensation, respectively. From the modeling results, it is found that the higher the pyrite content the coal contains and the more moisture that condenses in an environment with high relative humidity and initial temperature, the higher the potential for spontaneous combustion.

Jan 1, 2014

By Joseph Cervik

Common methods of controlling gob gas in U.S. nines are by means of ventilation of gob areas and gas drainage through surf ace boreholes. Costs of drilling surface gob holes increase as deeper coalbeds are mined. Where gob holes cannot be drilled because of topography, ventilation is the only means of control. Even then, sufficient air may not be available to dilute methane in the bleeder entries to acceptable levels. Thus, new methods of gob gas control need to be developed that are independent of surface topography, and of the mine ventilation system, and less costly than present systems. Except for slight variations in procedures and equipment, Great Britain, West Germany, France, Belguim, Poland, and Czechoslovakia use a common methane control method that is different from the system generally used in the United States, This Bureau of Mines paper reviews European mining methods, mining conditions, and methane control technology and discusses their applicability to U.S. mines.

Jan 1, 1979

By J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The Sao Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in 1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000 ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999

By M. L. Leming

The mechanisms of Alkali-Silica Reactivity (ASR) are briefly reviewed, test methods are examined, and typical specifications are discussed. In addition, views on responsibility of the aggregate supplier regarding specifications are presented.

Jan 1, 1995

By K. W. Deter

The gold ores in the Jerritt Canyon district have been recognized as refractory since they were first encountered by FMC geologists in 1976. Upon obtaining managing rights as joint venture partner, Freeport McMoRan Inc. developed an operating plan featuring carbon-in-leach gold recovery techniques for the oxide portion of the ores and a patented sulphide oxidation step followed by chlorination for treating the organic carbon constituents of the refractory ores prior to CIL gold recovery. The plant was successfully started up in 1981 with the first gold poured on July 4, 1981. Initial plant throughput was designed to be 2495 MTPD (2750 STPD) total through the dual processing trains.

Jan 1, 1991

By J. Kallioinen

Flotation of low grade Ni ores with serpentinite host rock tend to yield low recoveries of Ni With high MgO contents in the concentrate. The recovery can be enhanced by optimizing the sub-processes in the pulp and in the froth. The new OF-100 flotation cell has been designed to be adaptable to different feed fineness (Coarse, Fine). The losses can according the research conducted at Outokumpu's Hitura plant be substantially decreased by OF-100's new rotor and stator design and froth zone geometry. The froth residence time is used to adapt for feed particle size changes measured by the Outokumpu PSI- 200. Models for the behaviour of different particle Sizes in the sub-processes have been developed. The modified froth zone geometry and the capability of maintaining a froth of desired thickness allows efficient washing of the obtained concentrate producing low levels of MgO.

Jan 1, 1994

By P. Tsang

The stability of longwall chain pillars depends not only on the mechanical properties of coal and surrounding rocks, but also geological and mining conditions. In order to evaluate the effects of each, variable, the orthogonal experiment design was employed in this study for significance analysis. The study concluded that the stability of longwall chain pillars is mainly controlled by the ratio of pillar stress to pillar strength, the ratio of Young's moduluds of the roof to coal and floor to coal, entry width, pillar width and the internal friction angle of coal. Additionally, horizontal stress, panel width and mining height also play a significant role.

Jan 1, 1994

By C. P. Blair

In discussing so-called "volume rates" for the movement of coal, I start from one basic premise: That it is the job of the railroads to devise rates which will move the traffic, while at the same time assuring a fair return on their investment. No matter how reasonable and nondiscriminatory freight rates may be, if they fail to attract and hold traffic to the rails, they are utterly useless - both to the carriers and the shipping public. And it will be my purpose here to show that under certain circumstances the use of volume rates by the railroads enables them. to hold traffic which would otherwise be lost, and to avoid needless dissipation of revenues, Properly employed, volume rates should benefit both the coal industry and the railroads, I do not, however, advocate the discarding of the carload as the basic rate-making unit. Far from it. Sound operating reasons dictate the making of rates based on car- loads, and the tradition of carload rates has a firm foundation in railroad operating costs, many of which vary directly with cars handled. In short, the carload was, Is and, in my opinion, will continue to be the basis for most rail rates on coal, as well as on other commodities. But change is an inevitable result of progress, and we should not be so bound by tradition that we are unwilling to try novel methods of ate making, should the circumstances require, The modern rate maker must, now and then, run the risk of being called an iconoclast if he is to keep up with the times. As T will point out, volume rates were for many years rejected by both the Interstate Commerce Commission and the railroads, But now both the Commission and the carriers have come to recognize that under proper circumstances and conditions volume rates are a powerful and effective tool.

Jan 1, 1959

By John Oskam

In 1873 Barton tines Corporation mining Garnets for Abrasives. From providing bulk Garnet Concentrate the technology has advanced to the sizing and classification of micron sized particles utilizing a Barton process. Processing of Garnet involves extensive quality control at all steps, first to insure product purity and secondly to insure the correct size range. Barton Mines produces about 30 different sizes of Garnet products to lead the world in the manufacture of technical abrasive Garnet. This paper will examine the present technology of Garnet Abrasive Manufacture and the specification to which the sizes are produced as well as some of the markets served.

Jan 1, 1980

By Joseph Moses Botbol

The disposition of world mineral resources is such that a vital need exists for both the most efficient development of existing resources and the rapid disclosure of as-yet undiscovered resources. The technological developments described in this report are directed primarily toward the acceleration and increased efficiency of mineral-resource exploration program. In the past decade the use of computers in the mineral industry has grown exponentially. Most computer applications in mineral exploration are designed to be implemented either before or after data collection. Few, if any, computer applications are designed to be used during the collection of data. One major reason for the lack of development of computer applications in this area is that comunications links do not exist between computing systems and the remote areas that host mineral-deposit exploration programs.

Jan 1, 1975

By M. J. Carlson

With the goal of improving the strength characteristics of pneumatically emplaced material used for localized subsidence control, the binding additives: fly ash, bentonite, and Portland Cement, were examined for their effect on the support capabilities of coal refuse. It was found that, within certain concentration ranges, all three of them offered some increase in the ultimate strength of the backfilling mixture; however, Portland Cement gave the greatest percentage increases. Selection of the appropriate backfilling mixture will allow for the most economical and efficient subsidence control when pneumatic stowing is employed.

Jan 1, 1987

By Philip L. LeHoux

In recent years, much work has been done to explain the nature of the gold-carbon adsorption mechanism. The benefits of a sound theoretical basis has the obvious application to gold adsorption and elution industrial processes. Unfortunately, the lack of a clear agreement on the mechanism has provided no clear direction towards process innovation and optimization. Jones' (1989) work has gone a long way towards clarifying the specie of gold adsorbed (and thus the chemistry required to remove it). Since the development of hot caustic and cyanide elution, the kinetics have been accelerated by the application of pressure to increase elution temperatures beyond the boiling point at atmospheric pressure. However, the traditional reagent content of 15 g/L NaOH and 5-10g/L NaCN has remained largely unchanged. This is in spite of work that has shown that the presence of cyanide is not required for the elution process to take place (Adams, 1986; Adams; 1989; Jones, 1989). Adams (1989) has also compared NaOH elution rates with and without cyanide. He found improvement with the use of cyanide and a synergistic effect with the use of both. Others have found no difference in overall extraction (Jones, 1989

Jan 1, 1990

By P. T. Bissert, J. P. Ducarme, J. D. Noll, C. C. Jobes

"There have been about 42 fatalities in underground coal mines between 1984 and 2015 where the victim was struck, pinned, or run over by a mobile machine (MM) such as a shuttle car, scoop, or battery hauler. MSHA has issued a proposed rule requiring proximity detection systems (PDS) on MMs in an effort to prevent future fatalities. Currently approved PDSs use electromagnetic (EM) technology to detect the presence of a miner and impose machine controls to prevent contact. The disadvantages of an EM-based PDS on MMs include the need for a miner-wearable component (MWC), environmental interferences, EM interferences from other devices, and low localization range and accuracy. NIOSH researchers are investigating alternate technologies that could improve the capabilities of the current PDSs. Many technologies were reviewed, and NIOSH researchers identified RFID, LIDAR, RADAR, ultrasonic detection, and computer vision as candidates for PDS development. The performance characteristics of each technology and its applicability to an underground mining environment will be discussed, along with international developments and implementations, and the concept of sensor fusion. INTRODUCTION PDSs provide safety to mine workers by detecting their presence (and in some cases location) around a machine. These PDSs provide a warning zone, which triggers an alarm, and a stop zone, which halts the machine before it contacts the miner. The Mine Safety and Health Administration (MSHA) issued a final rule requiring that PDSs be installed on all continuous mining machines (CMMs) on the working section, with the exception of full-faced machines, according to a phase-in schedule for newly manufactured and existing equipment [1]. The PDSs that were designed for CMMs have since been adapted to other mobile machines. Mobile machines include scoops, which are used as general utility vehicles, as well as coal hauling machines, such as shuttle cars, ram cars, and continuous haulage systems. MSHA has examined all accident reports from 1984 to 2014, and determined that 42 fatalities could have been prevented on mobile machines had a PDS been installed [2]. As such, MSHA issued a proposed rule that would require mobile machines on working sections (with the exception of longwall sections) to be equipped with a PDS. This rule would follow a phase-in schedule for newly manufactured and existing equipment. Currently available PDSs are based on electromagnetic (EM) technology. NIOSH researchers developed a shell-based magnetic flux density distribution model [3] for determining the position of a miner near a machine. A typical system would consist of four generators positioned around the perimeter of the machine. Each generator is a coil of insulated wire wrapped around a ferrite core. The magnetic field strength is proportional to the current running through the coil. Miners working on the section have an MWC, which is a transceiver that measures the field strength emitted by the generators and transmits a data packet over an RF link which contains the field strength reading to the PDS controller mounted on the machine. The magnetic field generators are pulsed sequentially such that the MWC can identify which generator’s field strength it is reading. This type of system utilizes the principle of magnetic flux density: the closer the MWC is to the field generators, the higher the field strength reading. Thus a miner’s presence can be determined once he gets too close to the machine, because his MWC will measure a magnetic flux density beyond a certain threshold. These thresholds are utilized on a per-generator basis to “shape” the fields for both warning and stop zones around a machine, as illustrated in Figure 1."

Jan 1, 2017

By Colonel Oattis E. Parks

The quantity of coal recovered by diamond coring techniques is not sufficient in many instances to make meaningful coking and/or ash fouling tests. Quantities in excess of that obtained by conventional coring techniques, usually in amounts exceeding 500 pounds, has been designated bulk sampling. During the past three years, AMAX Coal Company has utilized five methods of bulk sampling. It was our desire to obtain a bulk sample that was diagnostic of the seam by the most expedient and economical method. From the beginning all of our efforts have been directed to methods which would extract the required coal from slim boreholes which provide quick and inexpensive access to the coal seam, regardless of depth, terrain and accessability. In our efforts and investigation several large diameter cores have been taken from thick coal seams at relatively shallow depths in easily drilled rocks. On the other hand, for deeper thin seams multiple large diameter coring is more expensive and time consuming. It is somewhat less expensive when multiple cores are taken from a single slim borehole utilizing deflection coring, although considerable skill is necessary.

Jan 1, 1973

By Allan M. Harvey

Asbestos production in the United States is no match for the vast operations of Canada and the U.S.S.R. The majority of U.S. production is limited to the states of Vermont, California and Arizona, and the type of asbestos is limited to the variety of serpentine known as chrysotile. What little production of other varieties of asbestos such as tremolite and anthophyllite that has occurred over the past 100 years since asbestos became a useful commodity is of practically no significance. However, new developments in the field of environmental and occupational health hazards has startled the mining industry in this country and has already given a few particular companies reason to be concerned about the profitability and probability of their continued operation in the business of mineral processing. At the heart of these developments is the question and controversy over just what constitutes asbestos and what exactly is the definition of a fiber. To the mineralogist or, in fact, to practically anyone engaged in the process of mining and separating minerals there is little or no question about asbestos. It is not a distinct mineral but rather a commercial product serving specific applications for which a number of fibrous mineral types can qualify. To the hygienist pr health authority this definition is too general. They demand something they can detect, measure and control. To suit their purposes and simplify their task of detection, they have labelled the minerals chrysotile, crocidolite, amosite, tremolite, anthoph-yllite and actinolite as asbestos, and any particle of these minerals with an aspect ratio of 3:1 as an asbestos fiber. It does not

Jan 1, 1976

By E. Ashworth

A thermistor probe has been developed to measure in situ temperature profiles underground. A full description of the probe is given. Data collected from the probe has been used to compare the actual profiles with those predicted from a finite element analysis using laboratory measured thermal properties of the different rock types. This comparison indicates the applicability of laboratory measured parameters in modeling the real conditions. Factors such as applied pressure, moisture content and anisotropy on laboratory measurements is discussed.

Jan 1, 1983

By W. Clark Ashby

Productivity is a fascinating concept. Like motherhood or apple pie, we know it as a good thing. Just what it means is not so clear. To a coal miner we assume it means tons of coal hauled from the mine. To the company president it means profit after capital, labor, and other costs have also been reckoned. To the government economist it means output in a balance of payments. What does it mean to the biologist, and can reclamation really be productive? In this paper we discuss productivity from a biological viewpoint, give some yield data for various types of reclamation plantings, and discuss how our demand for or acceptance of differing kinds of productivity is tied up in bigger questions of land use, environmental stability, and resource allocation.

Jan 1, 1981

By T. W. Camm

"Search Amazon.com using the keyword “leadership,” and you are rewarded with a list of over 144,000 titles. There is no shortage of books and articles, many of them well written, with excellent ideas. So why is there still a constant cry for effective leadership in organizations? Often, the person in charge has personal blinders that prevent them from seeing or understanding how to implement the newest leadership idea or method. Either deliberately or subliminally, there is a disconnect from learning about leadership, and actually modelling and implementing what has been learned. Some current research in leadership theory can provide insight and tools to address this issue. INTRODUCTION Let’s start with a discussion of terms. Pseudo is defined by Webster (2015) as “Being apparently rather actually as stated.” Synonyms include affected, assumed, contrived, fake, false, phony, pretended, and artificial. Antonyms for pseudo provide additional clarity, especially when we consider terms normally associated with effective leadership: genuine, natural, unaffected, unforced. A similar type from my world of academia is a pseudointellectual, “A person exhibiting intellectual pretentions that have no basis in sound scholarship” (Dictionary.com, 2015). This is a person pretending to have an interest in intellectual activities for status; a fraudulent intellectuality. The thought of applying the term pseudo to leadership first occurred to me while reading Power and Innocence by Rollo May (1972). In discussing the dynamics of power, and how the innocent are often victims of the exercise of power, especially the more aggressive and destructive types of power, he saw two types of innocence. The first he called authentic innocence, which he described as a childlike clarity that carried into adulthood. The second type he called pseudoinnocence, a type of naïveté that makes a virtue of powerlessness, weakness, and helplessness; being more childish than childlike (p. 48-50). Just as there is the potential for pseudoinnocence and pseudointellectuals, it is also possible to experience pseudo leadership. (I hope the gentle reader is not troubled by my decision to use pseudo leadership as two separate words, in contrast to the use of compound words for pseudoinnocence and pseudointellectual cited above. Since there is no official definition of pseudo leadership, I have exercised my author’s prerogative to treat it as two words, both because I think in this particular application this makes the most sense, and also I think it is easier to read). As we will see, there are numerous theories applied to leadership. What is so troubling to many of us in organizations, there are a myriad of “leaders” in companies espousing pet theories, but very few instances where the actions of these individuals match their words. This is a particularly important problem when we look at the effect this has on the day to day operations of a mine, and where effective leadership (or its absence) can have a profound impact on both productivity and safety."

Jan 1, 2016

By A. D. Pernichele

Four types of slope failures in waste dumps are recognized; debris flow, foundation failure, edge slump and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is considered to be the most dangerous because of its explosive mode of failure and lack of forewarning. The December failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicated that the impounded water was due to a zonal accumulation of Jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1971