Search Documents

By Charles L. Kimbell

The year 1988 for the minerals indus¬try was one of favorable worldwide economic conditions for continued, rationally constrained growth. There was continued improvement in relations between market economy nations and the Soviet Union and China. The "shooting war" between Iran and Iraq ended. Soviet troops withdrew from Afghanistan. And conditions were generally favorable for economic growth in developed market economy countries. These favorable conditions were darkened only somewhat by the continuing foreign debt crises discernible in some major mineral producing developing market economy countries. However, there were situations developing that became major headlines in the late spring - situations that may have pronounced effects in 1989. The most significant event is the muddled situation in China. There is a good chance of worsening international relations and consequent restraint of development projects that could prove beneficial to China and her international partners. Of only slightly lesser evident significance was the death of Ruhollah Khomeini in Iran. This could lead to a variety of paths for the new Iranian leaders. Continued outbreaks of ethnic unrest in the Soviet Union clearly presented problems to the Gorbachev regime. This unrest has raised questions of how far the doctrines of "glasnost" and "peristroika" would be extended, including extensions into the minerals field. Another area of unrest is Panama with its tainted election and the Western Hemisphere's obvious dissatisfaction with the Noreiga regime. While not a direct threat to any major mineral industry enterprise, the political situation certainly presents a potential threat to the Panama Canal. That threat would have considerable impact on world

Jan 1, 1989

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By Mostafa Benzaazoua, Mariam El Adnani, My Ahmed Boumehdi, Rachid Hakkou, Salah Ouhamdouch, Abdelmalek Goumih

This study focuses on the environmental characterization and assessment of long-term neutral mine drainage (CND) potential from waste rock piles at the abandoned Erdouz mine in Morocco. The study involved metallographic analysis, static tests, and column tests. Results indicate that the waste rock is not an acid mine drainage generator but produces CND, mainly with sulfates exceeding Moroccan standards. The waste rock is relatively stable and could be reused after pretreatment.

Jan 25, 2022

By Bo Hyun Kim, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health have tested the finite element code, UT3PC, with LaModel to evaluate their results using know case studies. The purpose of the testing was to demonstrate the usefulness and limitations of these programs in evaluating mine layout design. Both of these software packages are simple to use and free for public download. Their use by mine engineers, along with other tools, such as empirical methods, can enhance the assessment of a mine layout design. LaModel can model mining layout on a mine scale or, at least, on a multiple-panel scale. However, this software has limitations in calibrating to conditions at many coal mines in the western United States. The UT3PC software models smaller parts of a mine and is used to evaluate the design of pillars, shafts, or drifts; but the software calculates all components of the stress tensor and provides stresses, displacements, and safety factors throughout the model volume. The two codes are used to evaluate design of one known case, and UT3PC is used to evaluate another case. The results and approaches demonstrated in the testing are intended to aid mine engineers in evaluating site-specific problems and to show that these tools can provide useful information to the mine engineer in evaluating mine layout design.

Jul 1, 2023

By F. Calizaya

This study summarizes the results of various numerical and laboratory experiments per-formed to study the effect of airflow recirculation on gas concentration. The numerical exercises were carried out on a simulated mine ventilation net-work. The laboratory experiments were conducted at the Mackay School of Mines' airflow monitoring system in Reno, Nevada. In both cases, the airflow was recirculated through the system by means of a main fan and a set of booster fans. The booster fans were positioned to produce two types of recirculation: In line and Cross-cut. For each type, various recirculation conditions were generated by changing the booster fan pressure. During each test, the gas emission rate at the simulated working face was kept constant. The study illustrates the conditions under which controlled airflow recirculation may be used to solve a district ventilation problem.

Jan 1, 1991

By P. Guliov

In the first part of this paper the authors present an overview of industrial minerals produced in the Canadian provinces of British Columbia, Alberta and Saskatchewan, and supplied to the Pacific Rim countries. The second part outlines some of the unique opportunities for industrial minerals that exist in the three western Canadian provinces and those minerals we feel have development potential for overseas markets. Because of time constraints, it is not an exhaustive presentation on industrial minerals, but is focused on a few selected minerals that we believe have high potential.

Jan 1, 1990

By S. A. Anzalone

The Helvetia copper deposit is a large undeveloped Laramide porphyry copper system located in the Santa Rita Mountains, Pima County, Arizona. This porphyry copper system consists of four areas of copper mineralization: Rosemont, Peach-Elgin, Broadtop Butte, and Copper World. Asarco refers to the four areas collectively as the "Helvetia Deposit". Mineralization and alteration are primarily contact pyrometasomatic, and zoning of hydrothermal alteration and sulfide mineral assemblages are similar to those observed at the Twin Buttes and Mission copper mines located approximately 32 km west of Helvetia. Asarco acquired the Helvetia Deposit in 1988 and has continued the exploration and development effort since then. A considerable amount of excellent geological work has been completed in the area but little information has been published on developments since the mid-1950's. The geology of the deposit as developed by numerous geologists over the past 75 years and the large, bulk tonnage low grade copper deposits outlined in recent years will be briefly reviewed in this paper.

Jan 1, 1992

By Hongling Wang, DI WU, Shuai Li, Hui Shu

Isothermal reduction experiments on carbon-bearing pellets of copper slag were investigated by the thermogravimetric method with biomass carbon as a reducing agent. The results indicated that the reduction process of copper slag‑biomass composite pellets was dominated by gas phase diffusion, and the apparent activation energy was 88.44 kJ/mol. In the temperature range from 1000 to 1200 °C, the metallization rate of pellets increased with increasing temperature, and the maximum metallization rate was 78.4%. The optimal reduction temperature of CSBCP (copper slag-biomass composite pellets) was 1200 °C.

Nov 23, 2022

By J. Hahn

Modern high-performance disc filters such as the BoVac Disc Filter have set new standards in applications where large capacities of solids, liquids and air have to be managed through the filters. These disc filters have an enormous hydraulic capacity. For applications in mineral processing - with a special focus on tailings – which typically have high solids throughputs but low filtrate and air flows, this capacity can be used to expand the filtration area while maintaining the benefits of very good cake discharge even with thin cakes (4-5 mm) and a high filter speed. Research work over the last century has proven that increasing the filter area should be achieved by increasing the disc diameter. Because adding more discs leads to big problems with the cake discharge. However, as the disc diameter increases, the filter segments become longer and heavier. A suitable compromise was therefore found by doing both. The result is the first vacuum disc filter that offers significantly more than 300 m² of filtration area, but has no more than 6 discs.

Feb 1, 2023

By S. P. Mehrotra

In this review article, various approaches and mathematical models that have been used to simulate, design, and synthesize flotation circuits are examined. First, a brief review of flotation kinetics is presented which is followed by a discussion on simulation of flotation circuits. The existing literature on optimal design of flotation circuits has been divided into two broad categories. In the first category, a generalized integral approach is used wherein the optimal circuit design involves determination of both optimal interconnection of various flotation cells/ banks of cells in terms of structural parameters and optimal values of various operating parameters. In the second category, a conventional circuit configuration is assumed to be the best configuration; the optimal design here only means the optimization of operating parameters. The merits and demerits of these two approaches are discussed.

Jan 1, 1987

By W. L. Price

Recent publication of United States Bureau of Mines figures showed that the sand and gravel (3) industry is the largest single mining industry in the United States in term of yearly tonnage produced. The yearly production of over 500,000,000 tons per year now exceed bituminous coal production. This disclosure caught unawares many observers who have not been following closely the rapid-growth of this phase of mining. Along with this steady growth in production, the sand and gravel industry has gone through an accelerated and varied program of beneficiation in a period of the last ten years.

Jan 1, 1958

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and galvanodynamic and chronopotentiometric techniques were used to characterize the effects of DXG-F7®, a commercial smoothing agent, on copper electrodeposition onto 316L stainless steel from a synthetic electrolyte containing 40 g/L copper (Cu2+), 160 g/L sulfuric acid (H2SO4) and 20 mg/L chloride (Cl-) at 40oC. The findings were compared against results using HydroStar® 4208, a modified polysaccharide. The nucleation overpotential and plating potential observed in cyclic voltammetry and galvanodynamic testing showed that neither DXG-F7 nor HydroStar significantly polarized acidic copper electrodeposition. Subtle differences between the additives were found during EIS testing and modeling, but more research will be needed to fully understand these differences. Surface-roughness measurements of two-hour deposits indicate that DXG-F7 and HydroStar produced smoother deposits as their concentrations in the electrolyte increased. No difference in the surface roughness of deposits was detected between the additives. Based on the experimental evidence resulting from the laboratory testing, no significant difference was found between DXG-F7 and HydroStar at 20 mg/L Cl- concentration, with the exception that DXG-F7 dissolves more easily in water than HydroStar. Introduction Cathode deposits obtained from acidified copper sulfate electrolyte(s) without organic additives are often soft, coarsely crystalline and nodular (Sun and O’Keefe, 1992). Therefore, small amounts of organic additives are added to the electrolyte to produce level and dense cathodes during copper electrowinning. The action of organic additives is thought to be due to their adsorption on the surfaces of the newly formed copper grains. Hence, any copper grain that grows excessively fast adsorbs a layer of organic additive, which inhibits growth. The result is a smoother and harder deposit of suitable purity (Sun and O’Keefe, 1992). In part I of our four-part series on the examining of copper electrowinning smoothing agents, a review of previously published work on organic additives used during copper electrowinning was presented (Moats, Luyima and Cui, 2016). In the review, it was noted that many tankhouses had switched from guar to other saccharide-based products such as HydroStar and DXG-F7."

Jan 1, 2016

By V. O. Tenorio, K. W. B. Requist

As the mining industry begins efforts to examine the feasibility of extraterrestrial resource utilization, the extraction and processing of icy regolith containing water and other volatile materials will be the initial focus for future expansion of capabilities. Pure water is essential for human consumption, and a source of oxygen and hydrogen. The latter, along with the volatile materials, lend themselves to the creation of fuels that may be used for further space exploration at distances not currently feasible. For any extraterrestrial scoping project, the transport of materials to geoscientists remains virtually impossible. Therefore, analysis must be done in-situ, possibly millions of miles away from the nearest human. To address the need for geologic resource estimation in the absence of geoscientists, an infrared framework has been developed for the analysis of water ice content in simulants of permanently shaded lunar regolith. This framework relies on a convolutional neural network model for the rapid analysis of percent water ice content in samples, at which point standard geostatistical methods may be employed.

Feb 1, 2023

Projections of coal reserves in Central Appalachia are essential for long-term planning in the region. Annual production is declining in some states, such as Virginia, and mineable reserves for the Central Appalachian Coalfield are challenged by difficult geological, mining, and market conditions. In order to project coal mining longevity in this region, interviews with mining companies were conducted to assist in the determination and assessment of technical and economic factors that impact coal seam mineability. This information was applied to seam and coal reserve data developed by state and federal governments. The results were carefully analyzed to determine the effects of various factors on the overall mineable coal reserve base.

Jan 1, 1998

By Jack G. Quade

During the summer and fall of 1973 a series of Skylab and high-altitude aircraft overflights provided excellent hard-copy photographs of the Great Basin. These photographs, with a wide range of ground resolution were used by the NASA Project of the University of Nevada, Reno, to conduct specific geologic studies. The principal objectives of these studies were to: select individual areas covered by Skylab photography for detailed studies, develop mapping techniques using varied film-filter products with a wide range of ground resolution, compare the results of the mapping techniques to existing geologic maps at comparable scales, verify the results wherever possible by direct field observations. These studies were conducted by Jack Quade and Dennis Trexler and by graduates and undergraduates of the Reno campus under a contract with the Manned Spacecraft Center Houston, Texas.

Jan 1, 1976

By Roland W. Merwin

The Bureau of Mines has studied the possibility of using the heap leaching process for treating the gold ores in the sedimentary beds of northeastern Nevada. This paper summarizes all available information on the technical and economic feasibility of heap leaching oxidized ores from these beds, past industry application of vat leaching, results of recent Bureau of Mines and industry tests on heap leaching ores from this region, and requirements for planning the proper application of heap leaching. Preliminary tests on representative samples of ores from the region show that a satisfactory recovery of gold can be obtained by heap leaching the ores with cyanide at a relatively coarse size. Significant deposits of gold ore occur in sedimentary beds of various locations over an extended area 40 miles wide and 200 miles long in northeastern Nevada. The area is centered 40 miles west of and runs parallel to the leading edge of the Roberts Mountain thrust fault system, a prominent geologic feature in the area. The general locations of past and present gold mining operations are shown in figure 1. (slide 1)

Jan 1, 1969

By J. J. DeMull, B. A. Boster

Amax's Sleeper mine uses conventional cyanidation milling and heap leaching techniques to produce gold. Since milling operations commenced in March 1986, average ore processing rates have improved from the design rate of 455 t/d (500 stpd) to more than 720 t/d (795 stpd). Heap leaching was added to the process facilities in September 1986 at a design rate of 1.5 kt/d (1650 stpd) and current heap leaching rates exceed 2.7 kt/d (2950 stpd). Presented are descriptions of the Sleeper processing facilities with emphasis on the crushing and grinding circuits, a review of the selection of crushing and grinding equipment, and a summary of operating performance during the first 16 months of operations.

Jan 1, 1990

By David R. Kalasky

One of the primary areas of computer application in mine ventilation has been the analysis of mine ventilation networks. A variety of network analyzers that are aimed toward the solution of flows in a given network has been developed. These programs typically use the Hardy Cross or other iterative algorithm for solution of any network, even those that are complex. The computer software has become more efficient and sophisticated over time and has thus been widely adopted for ventilation network analysis. One of the shortcomings of these programs is that they have been developed with the idea of analyzing the ventilation requirements at a single point in the lifetime of a mine. This provides the ventilation engineer with an important tool for analysis but falls somewhat short of providing a convenient means to economically com- pare alternative methods for ventilating a mine. The program described in this paper provides such a tool. The principal concepts that were necessary for the completion of a computer program that analyzes ventilation alternatives is the capability of efficiently determining the ventilation requirements at a variety of times during the lifetime of the ventilation system and some method of analyzing the costs of the alternatives on a realistic comparative basis. To accomplish this task, the authors began using Penn State's mine ventilation simulator designated as PSU/MVS, Didyk et al. (1977a, 1977b) and added the necessary additional software to accommodate the need for multi-period, time-dependent analysis of the net- work. The software was then tested on a coal mine ventilation problem with a 23-year life. The problem points out the value of such a program for ventilation analysis.

Jan 1, 1986

By A. Bruynesteyn

The results of leaching experiments in columns simulating 80 and 200 ft deep cores through a leach dump are discussed, By equipping the columns with can precipitation plants, actual plant conditions could be duplicated. The results produced a better understanding of the physical and chemical limitations of the leaching process.

Jan 1, 1975

By Hiroyuki Tamaru, Futoshi Kusumoto, Kosuke Tanimura, Atsuyuki Kimura

"SUMMARY The Hachinoshiri tunnel is a 2,469 m long two-lane road tunnel on the Chubu-Odan Expressway. Since more than 70% of the total tunnel length consists of low strength rock masses the competence factor of which is less than 1.0, it is expected that a self standing span cannot be achievable because of no ground arch to be established. The tunnel was thus designed with tunnel support patterns forming multi-arc early ring closure that can develop the load-carrying capacity estimated from the exerted earth pressure, Po, which can result from the competence factor, cf. The tunnel support pattern was selected based on the competence factor at tunnel face, then the subsequent tunnel support patterns were determined with reference to the monitoring data. The tunnel construction adopted full-face excavation accompanied by early ring closure using a 330 kW road header. The proposed construction methods at this tunnel site have turned out ensuring tunnelling in massive squeezing rock, so that they can be verified as reasonable tunnelling technologies, clarifying the relationship between the characteristics of the mechanical behaviour of the tunnel and its design parameters. INTRODUCTION The presence of highly weathered mudstone having the competence factor less than 1.0 where the tunnel became unstable with the early ring closure having the distance to early ring closure, Lf, of 6 meters, resulting in difficulty in maintaining the inner section of the tunnel, prompted a substantial amount of high strength double support and replacing of the tunnel support (Sato et al., 2015). Based on the mechanical characteristics learned from the construction, the mechanical stability of multi-arc tunnels was investigated using 3D FDM analyses with respect to the ratio of the radius for early ring closure, r3/r1, and the distance to early ring closure, Lf, so that tunnel support patterns for early ring closure can be established in terms of the competence factor, of, which was employed for a 725 m long section. Consequently the tunnel support patterns for early ring closure which can be determined from the competence factor became applicable to tunnel construction. The relationship between the characteristics of the mechanical behaviour of the tunnel and its mechanical parameters was also clarified. The early ring closure method adopted ensured tunnelling in massive squeezing rock, verifying its effectiveness in stabilizing the tunnel."

Jan 1, 2016