Search Documents

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. Moreover the texture parameter of the ARB-ed samples was calculated using their XRD patterns and the related equation. Additionally, the texture evolution during the ARB process was demonstrate by analyzing the measured pole figures and orientation distribution functions (ODF) and skeleton lines. The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. Texture analysis revealed fiber textures have been discovered with continiuose of the ARB process cupper. Brass, S and dillamor textures identify which their differences are in intensity of ARB process. Results indicated conformity between mechanical evolutions and texture evolutions during ARB process.

Oct 1, 2011

By Baseer Abdul, Edouard Asselin

Hydrometallurgical leaching of sulfide concentrates of copper and nickel at medium temperature (150°C) produces residues that contain sulfur and iron bearing minerals and phases. During leaching, and depending on various process parameters, iron may be precipitated as hematite, goethite, jarosite or other oxyhydroxides, which may be more or less crystalline. Hematite is the favored precipitate because it is the most environmentally stable and does not ad/absorb as much copper, nickel or other solution constituents during precipitation. However, the low solubility of iron during the medium temperature processing of sulfide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. In some cases these phases have been positively identified as the metastable ferrihydrite, which transforms into iron oxides such as goethite, hematite and magnetite over time. A better understanding of what may help drive this transformation during leaching would ultimately result in lower valuable metal losses and more stable leach residues. Higher acid concentrations result in increased copper extractions and favor the formation of hematite during concentrate leaching, rather than other metastable phases. Furthermore, commercially available water displacement formula “WD40®” and other novel reagent(s) affect Fe precipitation and sulfur chemistry, leading to very different process outcomes such as improved extractions and larger, more easily separated, sulfur particles.

Jan 1, 2017

By N. Schreithofer, M. Aspiala, R. Serna

The novel attachment timer apparatus presented in this paper serves as a diagnostic tool that allows the detection of changes in bubble-particle attachment probability and therefore floatability caused by alterations in the chemical environment and particle properties. The apparatus consists of six identical capillaries where bubbles with defined size are produced simultaneously in a measurement chamber. The bubbles at the capillary tips are placed in contact with the submerged particle bed for specific time periods, controlled with the help of automatic actuators. The advantage of the instrument is that hundreds of bubble-particle contacts can be measured automatically within a short time period. Microscopic pictures of each measured bubble are taken while recording the movement of the bubble before, during and after contact with the solid particles. The recorded pictures can be used to determine the actual bubble size and its corresponding deviation, and to detect the attachment of particles. The attached particles are collected in a detachable chamber for subsequent characterization. Furthermore, the device is portable and can be taken to the mineral processing plants for quick evaluation of particle-bubble attachment efficiency with particles and process water sampled directly from real processes.

Jan 1, 2017

By M. Jarvis, D. B. Dreisinger, T. Hitchins

Mineral carbonation (MC) has been extensively researched all over the world since it was found as a natural exothermic process to permanently and safely sequester CO2. In order to accelerate the natural process, various methods for carbonation of Mg-/Ca-silicate minerals and other industrial wastes have been studied. It has been found that the MC efficiency will increase with an increase of CO2 pressure, retention time, temperature, mass ratio of Mg or Ca to Si in minerals, specific surface area, and the slurry concentration in a specific range, and with the introduction of an effective catalysts, for example, 1M NaCl and 0.64M NaHCO3 or carbonic anhydrase. However, there still is not a successful industrial application because of high economic cost and slow reaction rate. It is not economic to exploit Mg- and Ca-silicate minerals deposits or tailings to sequester CO2 by MC, due to the cost of grinding and heat pre-treatment and in some cases the whole sequestration process may result in more CO2 emissions than the amount of CO2 sequestered, due to the requirements of energy inputs. The process however, may be profitable as a whole (with carbon credits). It is suggested to combine MC with recovery of valuable metals from ore deposits in order to reduce the cost for MC by cost sharing for mineral recovery.

Jan 1, 2017

By T. Newton, G. A. Bezuidenhout, P. J. Tauetsile, F. Trask

The technology to selectively leach gold, silver and base metals from ores, concentrates, and wastes, using an alkaline glycine solution, has initiated significant interest in using the new technology in various environments such as in-situ, in-place, dump, heap, and vat and agitated tank leaching. It has been shown that glycine acts synergistically with a number of other lixiviants to lower the net consumption of the other lixiviants while allowing low cost glycine solution recovery. Glycine is a non-toxic, stable, environmentally benign reagent that is available in bulk industrial quantities. It has the ability to dissolve most copper oxide and sulfide minerals, as well as native copper, whilst not interacting with acid consuming gangue nor dissolving iron and various or ubiquitous gangue elements. It acts synergistically with small amounts of cyanide to leach gold-copper ores at leach rates higher than either glycine or cyanide on their own, while significantly reducing cyanide consumption and eliminating detoxification requirements. The leaching behaviour of various glycine based systems will be reviewed, followed by the evaluation of the adsorption of gold onto activated carbon. Where the economics merit it, copper can be easily recovered using solvent extraction or sulfide precipitation.

Jan 1, 2017

By Erik Richer La Fleche

LEGAL RISKS LEGAL RISKS ARE COUNTRY RATHER THAN PROJECT RISKS OTHER COUNTRY RISKS ARE POLITICAL AND MACRO-ECONOMIC RISKS COUNTRY RISKS ARE EXAMINED AFTER PROJECT RISKS COUNTRY RISKS COUNTRY RISKS INCLUDE: WAR AND ARMED CONFLICT TERRORISM AND SABOTAGE CURRENCY INCONVERTIBILTY AND TRANSFER NATIONALIZATION AND CREEPING EXPROPRIATION GOVERNMENTAL BREACH AND REPUDIATION OF CONTRACT CHANGE OF GOVERNMENT CORRUPTION COUNTRY RISKS FIRST NATIONS AND LANDOWNER CLAIMS LABOUR UNREST SINGLE CAUSE ACTIVISTS REGULATORY AND BUREAUCRATIC DELAYS CONFLICT BETWEEN GOVERNMENT LEVELS ETHIC AND RELIGIOUS TENSIONS INTERNATIONAL SANCTIONS TAXATION CHANGES CHANGES IN LAW

May 1, 2013

By A. M. L. Cushing, S. Kelebek, A. Ghahreman

Iron sulfides are part of many ore deposits affecting flotation separation of non-ferrous base metals from them. Open-circuit potential (OCP), potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) measurements were carried out with pyrite and pyrrhotite electrodes to investigate their reactivity under various flotation conditions, which involved the use of TETA, SMBS, and their combination. TETA was found to adsorb on the electrode surfaces causing a significant increase in charge transfer resistance of the product formed, which was most significant at OCP. This effect is much less with SMBS, indicating its greater surface reactivity compared to TETA. The combined use of these reagents decreases charge transfer resistance to a greater degree than that experienced with their individual uses. Addition of Cu2+ as a potential activator to this system nearly eliminates the action of TETA on the electrode surface, which can be attributed to sequestration/chelate formation in liquid phase. The relative effects of these reagents on pyrrhotite electrode are similar to that of pyrite. The main difference between the pyrite and pyrrhotite electrodes is that the observed charge transfer resistance on the pyrrhotite surface with each reagent case is significantly lower by 3 to 4 fold. This is compatible with its anodic nature and ease of oxidation since the OCP value of pyrrhotite is lower than that of pyrite. Results are discussed in relation to flotation/depression behavior of these iron sulfide minerals in mineral separation processes.

Jan 1, 2017

By Raj Thamburaj

"Over the last few decades, the emphasis on affordability and reduced cost of ownership has necessitated the development of innovative processes to carry out repairs in aero engine components. Conventional weld and braze repairs have evolved into advanced, sophisticated processes using state of the art knowledge in lasers, robotics and materials technology. This paper illustrates past and present scenarios in an attempt to illustrate progress that has been made in this area. The problems encountered in the past have been detailed along with the solutions that have been developed and commercially implemented to address these issues. Apart from technical progress, this presentation also addresses the progress made in business approaches and in Certification/Regulatory issues surrounding aero engine repair. Progress in Technology Repair technologies have also been the embryo from which new and revolutionary manufacturing technologies have evolved as well. Electron Beam Free Forming and LENS are examples of how a completely new manufacturing concept can evolve what was originally only a process to join metals. The current and future potential of these spin offs is discussed providing examples of application. While several problems have been solved over time with the implementation of advanced repair technologies, the demands of the industry have created new challenges. The paper describes these issues, outlines potential solutions and discusses the future of repair technologies in terms of the far reaching influence it is sure to have in design, manufacturing, maintenance management and life extension. Progress in Business Trends.Business approaches to repair and maintenance have also gone through considerable change with the introduction of ""Power by the Hour"" and other similar arrangements between the companies responsible for engine overhaul and the end-users. Program Based Logistics (PBL) is yet another innovation to provide a win-win situation for the repair service provider and the end user. This paper traces the development of these business initiatives and highlights successful applications. Progress in Repair Certification, Regulatory Issues.Understanding of the issues surrounding certification of repairs has also evolved with time and regulatory issues have been clarified considerably. Procedures for analysis and testing are much clearer and ""Check Lists"" are being drafted for certifying repairs on various engine components. The PMA phenomenon has added yet another dimension to the issues regarding certification and these are discussed as well."

Jan 1, 2010

By Jim Richard

Introduction Electric Vehicle Controllers (EVC) and the Northern Centre for Advanced Technology (NORCAT) have created two generations of Lunar Highland Simulant ?Simulant preparation techniques and equipment resulted from drilling activities in support of Regolith and Environment Science and Oxygen and Lunar Volatiles Extraction (RESOLVE ) ?The purpose of defining the compaction process was to minimize the effect of density on drill testing This allowed other variables including drill bit geometry, auger, RPM, and thrust to be evaluated independent of density ?Density of Highland Regolith falls within a range of 1.40 to 2.29 g/cm3 (p484 Lunar Source Book)

May 1, 2013

By J. Keith Haddock

"Introduction The Boundary Dam Mine is located 5 km south of the City of Estevan, Saskatchewan and is operated by Manitoba and Saskatchewan Coal Company Ltd., one of the Luscar companies. The entire production of 1.7 million tonnes per year is delivered to the Boundary Dam Generating Station of Saskatchewan Power Corporation. Geology There are basically two seams mined on the property, the main Estevan seam ranging in thickness from 3.0 m to 4.5 m with partings and the upper Roche Percee seam (roughly 15 m to 23 m above the Estevan) which ranges from 0.6 m to 2.0 m in thickness. Most of the reserves are concentrated in the Estevan seam, the Roche Percee only being mined whenever its thickness makes it economic to recover. The coal measures belong to the Ravenscrag Formation of Tertiary (Paleocene) Age. This formation is widespread in North Dakota and Montana and contains the lignite fields of North Dakota and subbituminous coals of Montana. The formation is gently tilted to the southeast at Boundary (0.5 degrees) and consists of weak sandstones, siltstones and silty mudstones. Reserves and Coal Quality The present minesite encompasses a coal reserve of approximately 50 million tonnes calculated to a maximum stripping depth of 37 metres or 20:1 mining ratio. The reserves form only a part of the total reserves in the Estevan area which are owned by the Saskatchewan Power Corporation. The coal being mined is classed as Lignite ""A"" and has the following specifications:"

Jan 1, 1985

By Ed Labelle, Terry Overton, Gary Bell

"LocationThe Miller Minerals lime and limestone production facility is located in the Temiskaming district of Ontario at Hailey bury on the west shore of Lake Temiskaming. Located less than 300 km from Sudbury, Timmins, Rouyn-Noranda and Val d'Or, the plant is very well situated to market products to the mining, pulp and paper, and environmental industries. Being located a few kilometres from the Trans-Canada Highway and the Ontario Northland Railway adds to transportation efficiencies.ProductsAt Miller Minerals, two principal products in various sizes are produced, which are limestone (CaC03) and quicklime (CaO).HistoryProduction of limestone products began in 1979 at this quarry site. During the 1980s, limestone products were marketed to a variety of applications for mining, forestry, environmental and agriculture applications. In 1990, the production of quicklime products began, following the commissioning of an Italian-designed vertical shaft calcining plant. During the 1990s, both quicklime and limestone products were produced to meet the customers' demands.From the quarry's conception until 1992, the operation was owned and operated by Dymond Clay Products. In 1992, it was purchased by Miller Paving Ltd. of Markham, Ontario, and became a key part of the company's industrial minerals sector of business. Other Miller interests include dolomite, cement, paving materials and waste management."

Jan 1, 2000

By M. J. MONEA

Canada's only economic high-swelling bentonite deposit is mined in Wilcox, Saskatchewan, by A vonlea Mineral Industries Limited. The bentonite resulted from devitrified and altered volcanic ash released during the Laramide Orogeny. Volcanic ash was deposited in a pre-Cretaceous basin that was formed by salt solution collapse structures. Sedimentary rocks in the Wilcox area belong to the Snakebite Member of the Upper Cretaceous Bearpaw Formation. Bentonite beds are 61 cm, 46 cm and 30 cm thick; these are separated by 365 cm and 182 cm of shale respectively. Saskatchewan bentonite is used primarily in the oil well industry.

Jan 1, 1984

By Serge Perreault

Le cuivre est un métal fascinant qui joue un rôle essentiel dans le développement des différentes civilisations depuis 7000 ans. Le cuivre est aussi un métal polyvalent et essentiel qui est très présent dans notre vie quotidienne. L’un des premiers métaux utilisés par les humains, il est un élément chimique qui se trouve à l’état natif, ce qui est rare pour les métaux. Il apparaît principalement dans des minéraux, notamment sous forme de sulfures, en raison de son caractère chalcophile (c’est-à-dire son attraction pour l’élément soufre). Le cuivre se trouve dans la croûte terrestre sous forme de minéraux de cuivre, tels que dans les sulfures dont la chalcopyrite, la bornite, la covellite et la chalcocite. Il est également présent sous sa forme native ou dans des minéraux oxydés comme la cuprite et dans des carbonates hydratés, comme la malachite et l’azurite. La formation de gisements de minerai de cuivre implique des processus géologiques complexes, notamment l’activité hydrothermale, les intrusions magmatiques et l’altération des roches. Les gisements de minerai de cuivre se trouvent dans divers types d’environnements géologiques, dont les gisements porphyriques, les gisements de cuivre encaissés dans des roches sédimentaires, les gisements de type skarn, les gisements de sulfures massifs volcanogènes, les gisements magmatiques de type nickel-cuivre, les gisements de cuivre oxydé, et d’autres [1].

May 2, 2024

By M. G. Goudge

IT IS ENOOURAGING indeed to note during the past year that, despite a slackening off in many markets and with numerous major difficulties and problems to solve, the mining industry of Nova Scotia was maintained at a very high level. The value of the Province's mineral production for 1957 amounted to approximately $65,000,000. This represents a drop of only 1.5 per cent from the figure of the previous year. Coal Atlantic Collieries, Ltd., opened a new coal mine during the year at Bras d'Or. This colliery is equipped with the most modern type of mechanical equipment available, with transport of the ?coal by a belt-conveyor system. Other mines in the Province continued to mechanize their operations by the addition of Diesel haulage locomotives and other mechanized mining equipment. New wash plants are in operation and .an additional one is planned.

Jan 1, 1958

By J. E. Dodge

Tasu, currently an open-pit operation, services the primary crusher from two areas by ore-pass raises. The problems encountered and advantages gained are discussed. Mine equipment and operating practices are covered, together with blasting practices, line drilling and the pre-shearing necessary to stahilize the pit walls.

Jan 1, 1968

By A. R. Byers

"Porcupine Peninsular mine is at the extreme southwestern end of North peninsula in Night Hawk lake, Cody township, Ontario. It lies approximately 10 miles east of the gold-producing district of Porcupine.Gold in quartz veins was discovered on Gold -island in Night Hawk lake in 1906, the same year in which the now famous Porcupine gold camp was discovered farther west. Most of the claims now held by the Company were originally staked by Charles Auer in 1907, In 1910 when the level of the lake was exceptionally low, gold was discovered in a quartz vein near the shore and close to the present mine shaft.The mine is developed by a main shaft to a depth of 440 feet, with levels at 80, 180, 300, and 425 feet vertical depth and by a winze to 630 feet. A mill of 200 tons daily capacity was built during 1923, Production commenced on January 4, 1924, and continued without interruption to May 31; 1926, when operations were suspended due to a decrease in the grade of ore. Total production amounted to 27,416 ounces of gold from 99,708 tons of ore, an average grade of 0.275 oz. a ton. Diamond drilling and re-sampling of the mine during 1934 and 1935 indicated approximately 1,480,000 tons, having an average grade of 0.123 oz. gold a ton, above the 625-foot level."

Jan 1, 1954

By R. Gutray, J. E. Grainger

This paper deals with the use of a cement-deslimed mill tailings mixture for a scraping floor in cut-and-fill stopes at Madsen Red Lake Gold Mines Limited. It describes the mixing and placing procedures and the precautions used with respect to the floor while mining in the stopes. Details of the mix are presented, and advantages and disadvantages discussed. The paper concludes with a brief outline of the costs.

Jan 1, 1966

By S. Akhlaghi

In many electronic/optoelectronic devices, interaction between the metal stack and solder is undesirable. If a reaction happens, a nonuniform joint containing spikes and voids is likely to form and as a result the heat dissipation deteriorates significantly, which in turn, leads to the degradation of the bond. In the present work the interaction between Ti/Mo/ Au metallization system, which was sputter deposited on AlN substrates, and Pb-Sn solder was studied by using scanning electron microscopy (SEM). Also, an EDX system was used to trace the changes in chemical composition of the layers after solder tests. The microstructural examinations show that the Ti and Mo layer from the Ti/Mo/ Au metallization system are not impermeable enough and thus Ca from the surface of the substrate moves all the way up to the interface of Au/Mo and forms an intermetallic at the interface, which grows over time.

Jan 1, 2006

"THE GOLD MINING REGION of Timmins - Val d'Or, astride the Ontario-Quebec border, has long suffered the effects of rising costs during the period when the U.S. price of gold was fixed at $35 per ounce. The federal government, through such assistance programs as that set up under the Emergency Gold Mining Assistance Act (E.G.M.A. ) in 1948, has subsidized the gold mining communities of Canada for a total of over $300 million to March 31, 1972. Of this, the Timmins - Val d'Or ""gold belt"" has received more than twothirds, almost $220 million. In spite of these continuous subsidies, only 12 gold mines are still producing in the Timmins - Val d'Or belt, whereas 71 mines have received subsidies for some period since 1948. The vital question is how the communities previously supported principally by the mining of gold will survive in the long run, as many of the older mines either are already depleted or are quickly becoming so. With the rising price of gold on the 'free market in recent months, prospects look a little brighter for the time being. Even with the increased official price of U.S. $38, which made the maximum government subsidized price about $48 per ounce, gold mines have not sold any gold to the government since January 1972 and some stopped doing so months before that. The populace of the region has not been enthusiastic about relocation nor about extensive retraining programs in the past and probably will not be in the future. So, when the remaining gold mines become depleted, the old problems of community depression will remain."

Jan 1, 1973

By R. W. Wein, L C. Bliss

Northern ecosystems are dominated by a harsh physical environment which dictates a need for biological adaptation. As yet, it is unknown just how these adapted plants and animals will tolerate industrial development. Our work, sponsored by university, government and industry, is part of an effort to evaluate this developmental impact. Our present studies and the results to date will be discussed. Other problems to which the environmental student may address himself in the future to ensure against environ-mental degradation will be suggested.

Jan 1, 1971