Search Documents

By M. Kunst

The creep behavior of three AJ62 alloys was investigated in a wide range of stresses and temperatures. Multi-level tensile creep tests revealed a distinct primary creep stage and a high stress exponent up to a value of 10. The threshold stress concept which is commonly used in combination with high stress exponents was utilized in the analysis of creep behaviour. This resulted in an effective stress exponent for the AJ alloys indi¬cating dislocation climb as the dominating creep mechanism. In addition, microstructural observations of the lamellar eutectic and of the a-Mg-matrix were carried out using opti¬cal microscopy, SEM and TEM. The creep properties of the alloys are discussed in the context of microstructural parameters such as phase volume-fraction, stability and solute supersaturation.

Jan 1, 2006

By A. R. Byers

"This paper describes the distribution, occurrence, and paragenesis of known sulphide deposits within an area bounded by longitudes 102°00' to 106°00' west and latitudes 54 ° 301 to 57 °00 1 north. The Precambrian bed-rock which outcrops over all but the southern fringe of the area con- . sists of regional metamorphic assemblages ranging from low grade or green schist facies to high grade or amphibolite-granulite facies. The areas . of low-grade metamorphism correspond to 'islands' of volcanic rocks which are surrounded by highgrade paragneisses and migmatites. Intrusive rocks range in composition from ultrabasic to granitic and may be divided into syntectonic and posttectonic sequences. The average composition of the former is granodiorite and of the latter quartz diorite.The massive sulphide deposits fall naturally on basis of mineral content into the following divisions: ( 1) pyrrhotite and / or pyrite, (2) sphalerite and/ or chalcopyrite plus iron sulphides, (3) sphalerite and galena, ( 4) sulphide-bearing pegmatite, and (5) nickeliferous pyrrhotite and / or chalcopyrite. The deposits of iron sulphides are ubiquitous. Ratio of pyrrhotite to pyrite is fairly constant for individual deposits, but their areal distribution appears to be independent of the nature of the enclosing rock and grade of regional metamorphism. All deposits containing ore-grade quantities of base metals have been concentrated at favourable structural locations. Copper-zinc and lead-zinc deposits appear to be associated with syntectonic granodiorite with the lead-zinc concentrations confined to calc-silicate gneisses. Copper-nickel deposits show a close relationship to post-tectonic gabbros and pyroxenites. The paragenesis is more or less the same for the majority of deposits, with iron sulphides and sphalerite being introduced early and followed by chalcopyrite and galena. Some vertical and / or horizontal zoning is apparent in a few deposits. Temperatures of formation and origin of the deposits are briefly discussed."

Jan 1, 1960

By J. R. Goode

"Coarse ore sorting is here defined as the physical separation of a mixture of coarse (+3/8 inch) ore particles into two or more separate groups of total value greater than that of the unsorted ore. An ore will probably be sortable if the geology of the orebody and the mining practices employed meet conditions outlined in this paper.The paper points out how sorting can substantially reduce tonnage variable operating costs because sorting can double the mill head grade of amenable ores by rejecting waste rock from the mine output. The effect of sorting on ore reserves is outlined. It is also suggested that sorting is a low cost alternative to conventional expansion.The mode of operation of the Ore Sorters Kadel 13 Photometric and MK VI A Radiometric sorters is detailed. The report concludes with detailed descriptions of the photometric sorting plant operated by the Doornfontein Gold Mining Company is South Africa and the Radiometric Sorting Plant presently under construction at the Schwartzwalder mine of Cotter Corporation in Colorado."

Jan 1, 1975

By A. C. Wilson

In 1991, local prospector C. ?Mickey? Clement recovered at least three alluvial diamonds from the Michipicoten River. Two of these stones were sent to the Department of Mineralogy, Royal Ontario Museum, where they were identified as industrial grade diamonds with weights of 1.05 and 1.13 carats. Both stones were described as frosted and graphite-inclusion riddled. In 1995, prospector Sandor Surmacz and geologist Marcelle Hauseux discovered diamonds in bedrock approximately 20 km north of the Michipicoten River. An 18.1-kg bulk sample of a xenolith-rich lamprophyre, taken from an outcrop at the side of the Trans Canada Highway north of Wawa, yielded 1 macro diamond and 5 micro diamonds. All but one was gem quality (Sage 2000). Since then, more than 36 occurrences of diamonds in bedrock have been reported in an approximately 30 km2 area centred 20 km north of the town of Wawa. The occurrences are hosted within a sequence of unusual, Archean-aged, heterolithic breccias previously considered to have no economic significance. Ten kimberlite occurrences also have been confirmed in the Michipicoten greenstone belt in the last 5 years. Two of these kimberlites are diamondiferous. To date, expenditures on property acquisition and diamond exploration in the Wawa are estimated at $120 million (CAN). This paper summarizes the geological observations made on these occurrences and discusses including the relationship between the occurrences and the regional geology.

May 1, 2003

By J. E. Sepulveda, R. Morrow

"The Linear Wear Theory provides a reliable framework for the assessment of grinding media performance at full scale. This theory can be applied for analyzing grinding media consumption rates in any given grinding operation as well as the evaluation of alternative grinding media products, based on actual operational data, correcting for conditions like ore hardness, feed and product sizes, mill power and circuit throughput; all of them unrelated to the grinding media intrinsic quality attributes. A series of Moly-Cop Tools 3.0 applications have been developed to facilitate the calculations involved. Moly-Cop Tools 3.0 is available, free of charge, to all interested parties through the corresponding author.INTRODUCTION Mineral grinding circuit operators recognize the significance of grinding media (balls) consumption on the cost structure of any full scale grinding facility. The effective cost associated with this essential consumable depends on two factors: delivered price and durability (quality) of the grinding media. When evaluating alternative grinding media varieties, there is a well accepted evaluation criterion by which a given media type is considered to be “cost-effective” when its unit application cost – normally expressed in $/ton of ore ground – is shown to be lower than that of a nominal reference condition: Grinding Media Cost = Ball Price x Ball Consumption (1) ($ /ton ground) ($/ton balls) (ton balls/ton ground) Under this criterion, an alternative, higher-price grinding media product could be “cost-effective” if its associated consumption rate is sufficiently lower than the reference media, enough to yield a lower grinding cost, as dictated by Equation 1. For the proper application of the above criterion, evaluators must rely on representative indicators of grinding media quality, ideally independent of most mill operating conditions. In each particular case, ball price is always a known component; however, it is not so evident how media performance (quality) differences amongst alternative product types could be assessed with a reasonable degree of accuracy and precision."

Jan 1, 2014

By John Postle, Maureen Jensen, Marcel Vallee, Bernie Haystead, Dan Hora, Graham Clow

The Committee's proposed standards establish definitions and guidelines for the reporting of Exploration Information, Mineral Resources and Mineral Reserves in Canada and are identified as the "CIM Standards" and referred to as such hereafter in this document. To provide additional clarification to Qualified Persons (QPs), guidelines have been included with the respective definitions. The CIM Standards are applicable to all minerals including industrial minerals, diamonds and other gemstones. Reserve definitions for bitumen, natural gas and oil are not included in these Standards. The CIM Standards are not intended to cover mineral inventory estimates that will be reported to government agencies.

Jan 1, 2001

By H. Cay, J. Zachwieja, T. Esplin, R. Ravenelle, T. Olsen-Tank

Barrick Goldstrike mine utilizes a carbon-in-leach (CIL) circuit to simultaneously leach gold into solution with cyanide and adsorb the gold-cyanide complex onto activated carbon for further refinement. If the gold bearing ore contains a significant amount of native carbonaceous material, gold cyanide can be adsorbed at these sites instead of onto the desired activated carbon and the gold is effectively lost to tailings in a detrimental process known as "preg-robbing." The preg-rob effect is considerably reduced by treating the ore with a surfactant, which is hypothesized to adsorb to and passivate the native carbon surfaces. Past laboratory and pilot studies have consistently demonstrated significant gains in gold recovery after treating carbonaceous ore with surfactant. With success in bench and pilot scale testing, a plant trial was conducted at Barrick Goldstrike to evaluate the feasibility of using an alkoxylated fatty amine surfactant (Ethomeen T/12) to aid in the leaching of high preg-robbing ores. This paper analyzes the performance of the surfactant during the plant trial in addition to the problems that occurred during the trial period. Suggestions for improvement are also discussed.

Jan 1, 2014

By D. G. MacBeth

Most belt scales on the market are factory calibrated to minimum accuracy figures of 0.1% - 0.2% at several load points. However, if the same belt scale is not properly installed and maintained on the customers conveyor then the scale will not measure up to the claims of the manufacturer or to the requirements of the operator.

Jan 1, 1975

?? Intro ?? Mass blast principle ?? LaRonde evolution toward mass blast ?? Overview ?? Mining method ?? Longitudinal ?? LaRonde evolution (2002 to today) ?? Drill and blast design ?? Consumptions and statistics ?? Mucking strategies ?? Case study ?? Examples ?? Conclusion ?? As underground mines extends to greater depths, few questions must be asked: ?? How to: keep operations safe eep operation effective reduce the cost maintain and control the dilution ?? Geomechanic method and practices; significant advances have been observed in the field of: ?? ground support ?? mining sequencing ?? Drilling and blasting; research and development has been less extensive, probably due to the following characteristics: ?? Drill and blast are mainly production-oriented ?? Drilling and blasting are more oriented toward productivity ?? Technology relies heavily on suppliers ?? Highly stressed ground conditions ?? generally help the explosives to break the rock for fragmentation ?? intensify over-breaks or blast-induced

Feb 1, 2008

By Henry Stoch

It?s a green, green world ? Public concern about the impact of human activities on the environment and the roles that businesses play in that impact is rising. What?s happened in the last few months? ? Recent news: ? British Columbia announces carbon tax in 2008 budget ? Federal Court ruling stalls oil sands approvals due to a lack of consideration of GHG implications ? US Energy Independence and Security Act could limit government procurement of oil sands-derived fuels ? Western Climate Initiative (WCI) suggests a ?first seller? approach for regulating generators outside WCI jurisdictions ? Implications ? A cost for carbon has arrived ? The lack of a GHG strategy can have a material impact on your business ? Regulations in other jurisdictions could affect your organization

May 1, 2008

By J. M. Hemstock, H. L. Ames

THESE forums have been held annually since they were introduced by Mr. L. E. Djingheuzian in 1957. The response of millmen to questionnaires such as the one this year is ample evidence of the interest these create. This year's topic is unlike those of past years since it is an attempt to understand a new concept of grinding rather than to improve the old. Before, we were thinking in terms of 2-5 cents improvement in grinding costs, now we will be discussing savings of 15-2 5 cents. As a background for this forum we will begin by summarizing the major controversial issues relating to grinding with steel, many of which will undoubtedly apply to pebble milling. Our •task to-day is to learn what has already been done in pebble milling and obtain a fair overall view of this method of grinding.

Jan 1, 1961

By C. Larsen, E. Goodwin, E. Konigsmann

"This paper describes the development of an innovative effluent treatment process for cyanide and heavy metal removal from tailings wastewaters at Hemlo Gold Mines Inc. Golden Giant operation.The importance of minimizing dissolution of contaminants in the gold leaching circuit is discussed, as well as using recycled water in milling circuits to the fullest extent possible. Finally, a brief description of the role of natural cyanide degradation in the tailings pond is provided.Emphasis is placed on the need for overall water quality management to ensure minimum effluent treatment process costs and complexity while producing excellent quality effluents.1.0 INTRODUCTIONHemlo Gold Mines Inc. owns and operates its Golden Giant Mine located forty kilometres east of Marathon, Ontario. The Golden Giant mine is one of three gold operations exploiting the large gold orebody located in the Hemlo area. The milling facilities include two stage secondary crushing, three stage, closed circuit ball mill grinding with no reagents, thickening, cyanide leaching and carbon in pulp gold recovery unit operations. The average throughput is 3000 tonnes per day of 10 grammes per tonne gold ore. Figure 1.1 shows a schematic flowsheet of the operation."

Jan 1, 1989

"4.1. IntroductionThis chapter reviews the geochemistry of the platinum-group elements (POE) in sulphur-poor silicate rocks, and the limited data on POE in silicate, oxide, sulphide, arsenide and sulpharsenide minerals. The earliest geochemical studies of POE in silicate rocks, minerals and meteorites were carried out mainly by Goldschmidt, the Noddacks and their co-workers, and are reviewed in Crocket (1969). These researchers established the siderophile character of the POE, emphasized the common association of the group with sulphides in ultramafic-mafic rocks and suggested that very low concentrations of POE are typical of sulphur-poor silicate rocks and minerals. Much of these data were for Pt and Pd only and are more than 50 years old. Because of the poor sensitivity typical of the available analytical methods, few reliable data were obtained on silicate rocks in these early studies. Surveys of POE geochemistry demonstrate that the data base for sulphur-poor silicate rocks is very restricted, although considerable highquality data for Pd and Ir have been accumulated (Wright and Fleischer 1965, Yushko-Zakharova eta/., 1967, Mertie 1969, Crocket 1969, 1979, Keays 1981).Two recent publications, Vol. 71, No. 7 (1976), of Economic Geology (An Issue Devoted to Platinum-Group Elements) and Vol. 17, Part 2 (1979), of The Canadian Mineralogist (Nickel-Sulphide and Platinum-Group-Element Deposits), are of special interest. These volumes are clear testimony to the impressive progress made in the last decade toward describing the mineralogical and geochemical aspects of POE ore deposits, but at the same time demonstrate the constraints in modelling POE ore genesis due to our meager knowledge of the. POE content and distribution among minerals in the source rocks of ultramafic and mafic magmas. It is clear that the phases hosting POE in mantle source rocks are poorly understood. Nevertheless, Naldrett and Duke (1980) have shown that the absolute and relative concentrations of POE in magmatic sulphide ores are related to the degree of partial melting of mantle peridotites, and subsequent processes of batch equilibration and fractional segregation of sulphides."

Jan 1, 1979

By Jodi Roberts, Curtis Deredin, Jean-Guy Paulin

"Since the establishment of the Six Sigma quality improvement program in 2001, several projects have been successfully carried out in the copper-lead, zinc, copper separation, lead upgrading and bulk flotation circuits in the Brunswick Concentrator.This paper provides an update on the process improvement initiatives that have taken place since 2004 using the Six Sigma methodology:•,The recirculation of warm water to the flotation circuit (to save on energy costs)•,Installation of a heat recovery tower to recuperate the heat lost from the zinc dryers•,Installation of an extra row of cleaner-scavenger cells for the copper-lead circuit for extra capacity, and a new reagent scheme for the copper separation circuit that have increased copper and lead recoveries.INTRODUCTIONThe Brunswick Mine Concentrator (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The concentrator utilizes selective flotation to produce zinc, lead, copper, and bulk lead/zinc concentrates. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.Figures 1, 2, and 3 illustrate the historical annual average metallurgical performance and process improvements achieved at Brunswick Mine for the zinc, lead and copper concentrate products. The objective is to continuously direct metallurgical performance towards increasing grades and recoveries while minimizing operating costs."

Jan 1, 2008

By Luis Castelli, Aldo Bonomelli, Giselle Schifferli, Claudio Zamora

"This paper introduces the operational concept and the description of a multi-site Remote Support Center for knowledge management and long-term process performance improvement.This centralized Support Center provides real-time monitoring of open-platform process automation systems, and on-line access to process data and control applications information for multiple sites.Considering that process automation is a key enabler to business performance improvement, sustaining effective performance benefits over time becomes essential. Unfortunately, changes in manufacturing process dynamics, technology obsolescence and in plant operational practices cause the control strategies to lose their effectiveness over time unless their performance is periodically evaluated, and if required, tuned to the new process conditions.A new concept in process automation is proposed through the addition of a new control loop based on performance analysis methodology which is intended to feedback process and automation operation information to system and process specialists, allowing for continuous manufacturing process improvement and sustainable production benefits through effectual control strategies.A remote support center can play a key role in the delivery of such services, by providing the base platform from which a comprehensive process overview and a centralized knowledge database can be executed and additionally, as an enabler for plant operational practices change.INTRODUCTIONA Benchmark on Automation Level in Copper Concentrators conducted by AMIRA in 2004, reported that the Codelco divisions scored below their peers in several categories.Codelco had thereafter been looking for a new automation concept, and had focused on process automation as a key enabler for process manufacturing and business performance improvement. The final decision was to create a strategic alliance with a world-class automation technology provider.The traditional approach based on isolated automation solutions/projects, showed that the control strategies benefits were decreasing progressively over time, because of the on-going need to adapt the control models to the ever-changing process conditions and different plant operational practices. Another consequence of this traditional approach was the wide variety of technologies and automation systems deployed in the different plant sites, with no common automation standards, and with low opportunities to transfer knowledge or practices."

Jan 1, 2010

By Horst Konig

This paper illustrates that, with the application of new processes, smaller steel plants using local raw materials can be economical and advisable. It also introduces the problems connected with the direct reduction processes, which use non-coking coal or gas as reducing agents, and which are employed in connection with conventional reduction to produce excellent results. Electric smelting is also discussed, and some practical examples of operating plants are given.

Jan 1, 1970

By Jason J. Crowder

Presentation Outline ? Introduction ? Costs of ground support and rehabilitation ? Why post-failure rock mass properties are necessary ? The Rock Mechanics Problem ? Present State of Modelling and Instrumentation in Mining ? Case Study Background ??Williams Mine ? Deriving Parameters for Modelling from Instrumentation ? Results from Case Study ??Back Analyses ? Discussion of Research Impact t Summary

May 1, 2006

By M. J. McLeod, S. Watters, G. G. Lutes, S. Castonguay

"Gold-bearing mineralization at Anomaly A occurs in polydeformed Ordovician turbidites of the Kendall Mountain Formation of the St. Croix belt in southwestern New Brunswick, and is hosted by WSWtrending, shallow-dipping, brittle-ductile high-strain zones associated with the latest stage of the second of four regional deformation events. Gold-bearing syn-deformational stockwork, massive, and multiply brecciated quartz-sulfide veined zones form irregular pods and sheets up to several meters thick, which contain arsenopyrite, pyrrhotite, pyrite, stibnite, and a variety of rare minerals that are gold-bearing. Mineralized zones are enveloped by locally auriferous, weakly to intensely altered wall rock. Vein paragenesis includes: (1) early (pre- to syn-D2) quartz-chlorite veins that are largely the product of migration of quartz by pressure solution; (2) crosscutting, multiphase, vuggy quartz-sulfide veins that contain most of the gold and are interpreted to be structurally controlled; (3) late, crosscutting, nondeformed, non-gold-bearing veins containing laumontite, chlorite, muscovite, quartz, fluorite, and base metal sulfides. Carbonate-poor alteration associated with zones of gold mineralization is lithology-specific, and appears to reflect overprinting of multiple events. Major elements removed during alteration include Si, Na, Mn, and Mg. The minor and trace elements removed include Co, Li, Sc, and possibly Sr, Ni, and Zn. Minor and trace elements added include Au, Ag, As, Sb, S, and possibly F, Cu, Pb, and Zr. On the basis of proximity, time constraints, and a similar ore mineral assemblage, gold mineralization at Anomaly A is interpreted to be a distal equivalent of the intrusion-related gold mineralization at the nearby Clarence Stream Main zone deposit. La minéralisation aurifère de l’Anomalie A se trouve dans des turbidites Ordoviciennes polydéformées de la Formation de Kendall Mountain, dans la ceinture de Ste-Croix du sud-ouest du Nouveau Brunswick, où elle est contenue dans des zones de déformation fragile-ductile à faible pendage de direction OSO associées au dernier stade du second de quatre épisodes de déformation régionale. Les zones aurifères syn-déformationelles se présentent en forme massive, de stockwork, ou de veines de quartz-sulfure bréchifiées à répétition formant des lentilles irrégulières et des couches de plusieurs mètres d’épaisseur contenant de l’arsénopyrite, de la pyrrhotite, de la pyrite, de la stibine, ainsi que divers minéraux aurifères rares. Les zones minéralisées sont entourées d’une enveloppe de roches faiblement à intensément altérées, localement aurifères. La paragénèse des veines comprend : (1) des veines précoces de quartz-chlorite (pré- à syn-D2) qui sont principalement le produit de la migration du quartz par solution-pression; (2) des veines polyphasées de quartz drusique et de sulfures contenant la plus grande partie de l’or, celles-ci sont considérées comme étant sujettes à un contrôle structural; (3) des veines tardives stériles, sécantes et non déformées contenant de la laumontite, de la chlorite, de la muscovite, du quartz, de la fluorite et des sulfures de métaux usuels. Les zones de minéralisation aurifère sont associées à une faible altération en carbonate contrôlée par la lithologie et semble résulter de la superposition d’événements multiples. Les éléments majeurs perdus durant l’altération sont le Si, le Na, le Mn et le Mg. Les éléments mineurs et traces perdus durant l’altération sont le Co, le Li, le Sc et possiblement le Sr, le Ni et le Zn. Les éléments mineurs et traces enrichis comprennent l’Au, l’Ag, l’As, le Sb, le S et possiblement le F, le Cu, le Pb et le Zr. Étant donné sa proximité géographique, les contraintes temporelles et les similitudes de leurs assemblages minéraux, la minéralisation aurifère de l’Anomalie A est interprétée comme un équivalent distal de la minéralisation aurifère associée aux intrusions du gisement avoisinant de la zone principale (Main"

Jan 1, 2008

By Keila Gonçalves, Aline Tavares, Danielly Couto

"The sulphide copper deposits from the Carajás area (North region of Brazil) were generated by the percolation of hydrothermal fluids in volcanic and granitic rock and are denominated as IOCG deposits (iron oxide copper-gold deposits). During these hydrothermal events a wide variety of gangue minerals such as amphiboles, biotite and fluorite were formed. These gangue minerals are enriched in fluorine and chlorine which are deleterious elements in the copper concentrate. Chalcopyrite and bornite are the main copper-bearing minerals and they can occur in veins, in brecchia or disseminated in gangue.The study, which included bench scale flotation tests and minipilot plant tests was aimed at improving the fluorine rejection in the flotation process during the flowsheet design for one of these Carajás sulphide copper deposit. All of the study was supported by quantitative mineralogical techniques such as QEMSCAN and the use of a scanning electron microscope (SEM).This paper describes and discusses the results obtained in the metallurgical tests and emphasizes the importance of the quantitative mineralogical characterization during the process conditions optimization and flowsheet design.INTRODUCTIONIron oxide copper-gold (IOCG) deposits encompass a wide spectrum of sulphide-deficient low-Ti magnetite and/or hematite ore bodies of hydrothermal origin and normally have important copper sulphide reserves. In the Carajás mineral province, located at the southeast part of the Amazon Craton in Pará State (Brazil), there is a variety of world-class (>200 million tonnes) Fe-oxide Cu-Au deposits (e.g. Salobo, Cristalino and Sossego), whose genesis has been assigned to hydrothermal fluid percolation in volcanic and granitic rocks. Figure 1 displays the location of the Carajás area.The hydrothermal thermal fluid composition was extremely variable. It may have contained gases, salts (brine) and metals. The metals were carried as various complexes and it is thought to have involved sulphur, chlorine and fluorine containing species. This resulted in some minerals formed during the hydrothermal alteration having high fluorine and chlorine contents. These elements result in smelter penalties in a copper concentrate because they cause the smelter off-gases to be more corrosive."

Jan 1, 2011

Reliable estimation of in situ stress is a major step in the analysis and design of underground excavations in rock, particularly for evaluating the stability of underground structures to prevent failure or collapse. In the last ten years, the Western Australian School of Mines (WASM) has studied and developed an AE stress measurement technique using orientated core named the WASM AE method. It allows the determination of a representative and detailed knowledge of the in situ stress field during the early stages of a project (such as mine feasibility studies), even in areas where development access is not yet available. The method has been used for in situ stress measurement at more than 80 mine sites worldwide with over 200 individual stress measurements carried out to date. This paper describes the sample collection, sample testing and reconciliation of results for very deep measurements carried out at the Craig-Onaping mine complex in Sudbury Canada. The results constitute the deepest measurements undertaken to date at the WA School of Mines and indicate that the main principal stress is horizontal and oriented parallel to a common regional sub trend in a NE/SW direction.

May 1, 2009