Search Documents

By H. W. Smith, R. D. Fournier

This paper presents the results of an investigation of a full-scale rod mill. Appropriate numerical techniques are developed for the experimental determination of the parameters of a dynamic mathematical model from steady state data. The results confirm that this full-scale rod mill behaves similarly to laboratory-scale ball mills for which results have previously been obtained. It is noted, however, that although the model presented is adequate for predicting over-all particle size distributions, the size distributions of individual components of a multicomponent ore cannot be predicted.

Jan 1, 1972

By M. W. Bates, A. L. Mular

This paper, based on work carried out at Queen's University, describes the development and use of mathematical models of the parallel cyclone classifiers being used in the Strathcona mill of Falconbridge Nickel Min.es Ltd.

Jan 1, 1971

By M. Kreuh

Crystalline Mg(OH)Cl and amorphous Mg2(OH)3C1 were successfully isolated from a hydrolyzed molten salt electrolyte sample in this work, It was found that the chemical form and crystallinity of the hydroxylchloride were controlled by the cooling rate of the molten sample when it was taken. Crystalline Mg(OH)Cl could only be obtained by cooling the molten electrolyte sample at a rate not faster than 0.6 °C/min, Upon more rapid cooling, the hydroxylchloride species precipitated as Mg2(OH)3Cl, The behavior of these solid hydroxylchlorides when contacted with fresh and non-hydrolyzed molten electrolyte at 550°C was also examined, It was found that the Mg(OH)Cl rapidly dissolved in the hot electrolyte and did not decompose into MgO at that temperature as would be expected from the literature, The dissolution rate of solid Mg2(OH)3Cl was found to be so slow by comparison that it resulted in the complete decomposition into MgO which thereafter was incorporated into the electrolyte as a suspended solid phase rather than dissolution.

Jan 1, 2004

By P. Langlois, G. Labonté, J. J. Barrett, J. Holmes

"The Voisey’s Bay mill processes a high-grade pentlandite and chalcopyrite ore in a largely pyrrhotite/troilite matrix. From 1994 to 1997, circuit development focused on making a 14% nickel concentrate. When flowsheet development resumed in 2001, the target grade was raised to 20% ni. initially triethylene tetramine and sulfite pyrrhotite depressants were used in a lime circuit, but by recycling process water and the contained thiosalts, the required nickel grade was made without depressants. construction of the mill was fast-tracked, with start-up in september 2005. ramp-up was faster than other recent nickel installations, with tonnage being limited by concentrate dewatering due to higher-thanexpected ore grades.RÉSUMÉ l’usine de traitement de Voisey’s Bay traite un minerai à teneur élevée en pentlandite et chalcopyrite dans une matrice formée surtout de pyrrhotite/troïlite. De 1994 à 1997, le développement du circuit ciblait la production d’un concentré à 14 % de nickel. lorsque le développement du schéma de traitement a été repris en 2001, la teneur cible a été élevée à 20 % de ni. initialement les déprimants triéthylènetétramine et sulfite de la pyrrhotite étaient utilisés dans un circuit à la chaux; cependant, en recyclant l’eau du procédé et les sulfosels qui y sont contenus, la teneur en nickel a été atteinte sans utilisation de déprimants. la construction de l’usine de traitement a été accélérée et elle a démarré en septembre 2005. la mise en opération a été plus rapide que pour d’autres installations récentes de nickel; le tonnage traité étant limité par le séchage du concentré en raison des teneurs de minerai plus élevées que prévu."

Jan 1, 2017

By K. Forsberg, A. Rasmuson, R. Rodriguez Varela, J. Martinez De La Cruz

"This study analyzes the separation of rare earth elements by means of a supported liquid membrane (SLM) with the final objective of recovering REE from an apatite concentrate (Alemrajabi, Forsberg, & Rasmuson, 2015; Mohammadi, Forsberg, Martinez de la Cruz, & Rasmuson, 2015). In this study, the feed phase consists of an aqueous phase containing REE, the membrane phase contains the organic solvent and carrier (D2EHPA and EHEHPA), and the stripping phase is a hydrochloric acid solution. An evaluation of mass fluxes, separation efficiency, and membrane performance is conducted. In order to analyze the suitability of liquid membranes in the extraction of REE, a deeper insight into the mechanisms causing instability is needed. In this study, surface tension is considered as the key factor of Marangoni instabilities and spontaneous emulsification.INTRODUCTIONThe demand of REE and their compounds has increased considerably due to their special physicochemical features that make them crucial elements for numerous high-tech applications, including wind turbines, hybrid cars, mobile phones, and defense technologies. They are also extensively utilized in traditional industries such as nuclear energy, petroleum, metallurgy, agriculture, and textiles (Xie, Zhang, Dreisinger, & Dyole, 2014; Zhang, Wu, Bian, & Zeng, 2014).Solvent extraction is widely used for the separation of REE (Xie et al., 2014; Zhao, Huo, Pan, Li, & Liu, 2014). Di-(2-ethylhexyl)-phosphoric acid (D2EHPA) and 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (EHEHPA) are two of the most effective extractants for the separation of rare earth elements among organophosphorus extractants (Gupta & Krishnamurthy, 2005). However, the difficulty in stripping loaded D2EHPA extractant, especially for heavy REE, has limited its utilization. Yttrium can be stripped at lower acidities in EHEHPA systems compared to D2EHPA systems (Gupta et al., 2005), but the extraction efficiency is lower. Conventional solvent extraction by mixer-settlers is restricted by its large solvent inventory and loading limits, and suffers from phase disengagement, emulsification, loss of solvent, and flooding problems (Swain, Jeong, Lee, & Lee, 2007). In this context, supported liquid membranes (SLMs) present a potential alternative due to their advantages, being low solvent inventory, process simplicity, low energy and operational costs, great enrichment ratio, and combination of extraction and stripping into one single step. A SLM is a system in which two aqueous phases are separated by an organic liquid membrane suspended in the pores of a porous support by capillary forces. One of the aqueous phases is the feed solution with the solute and the other is the stripping or receiving solution. The solute diffuses through the liquid membrane and then is extracted into the stripping solution (Kislik, 2010)."

Jan 1, 2016

By R. J. Enright

Eight mines in canada and three in Australia were visited between September 1987 and Februacy 1988. All mines had encountered problems with sulphide dust explosions and had introduced defence mechanisms to prevent or limit the extent of these explosions. Techniques included dispersion of limestone by various methods, use of water foggers, placing of water and inert stenuning in blast holes, and removal of settled dust to prevent secondary explosions. The techniques were evaluated and it was concluded that certain practices should be modified or discontinued as they were of little value in preventing dust explosions.

May 11, 1988

By T. Lux, H. -J. Krassnig, I. Filzwieser, E. Hecker, R. Degel, A. Filzwieser

Non-ferrous metals find their applications in smartphones, tablets and computers. These materials with their particular properties are the basis of our modern life. SMS group is well prepared for this huge market and for growing future challenges. A large contribution here is the new joint venture PolyMet Solutions that was founded by SMS group and Mettop, an Austrian engineering company, with the objective to develop new technical solutions for the primary copper production lines as well as for non-ferrous metals starting with the primary smelting of concentrate and ending with the electrolysis. PolyMet Solutions provides the process know-how whereas SMS group supplies the plants and equipment and Mettop the key components. SMS group and Mettop also cooperate in the field of tankhouse technology. Together with Montanwerke Brixlegg AG, Mettop has developed together with a parallel flow technology (METTOP-BRX Technology), allowing a current efficiency of above 98 % at a current density of 420 A/m², which is a milestone in copper electrolysis. For the secondary copper production route, SMS group and PolyMet Solutions developed an innovative refining furnace (PolyRefine) for the smelting and refining of copper scrap. The refined copper is directly charged to the Contirod line to produce copper rods and wires. The innovative cooling solutions of SMS and PolyMet Solutions come into play where furnaces have to stand the highest loads and stresses, for instance in areas of very high temperatures or temperature fluctuations, aggressive exhaust gases and slags, or at critical spots such as taphole areas. Custom-tailored cooling systems for furnace vessels make sure varying loads are compensated in a targeted and effective manner. The solutions include air cooling, spray cooling, cooling technologies with integrated copper elements such as CFM (Composite Furnace Modular) cooling systems, plate and finger coolers. The major innovation in the field of furnace cooling is the ILTEC (Ionic Liquid Cooling) Technology which paves the way for increased plant safety. This revolutionary, patented cooling technology is jointly marketed by Mettop and SMS group. It permits water-free cooling to be implemented and thus makes operation safe wherever it is applied. INTRODUCTION Non-ferrous metals or NF metals are changing the world. There is no modern industrial sector that can do without these valuable metals. Non-ferrous metals find their applications in smartphones, tablets and computers. These materials with their particular properties are the basis of our modern life. The importance of the non-ferrous metals market is reflected by two figures. In 2018, the production of non-ferrous metals was worth more than 237 billion Euros. This contrasts with 255 billion Euros of the value of iron and ferro- alloy production in the same year (International Organizing Comittee for the World Mining Congresses, 2018). Hence, the NF metal industry is almost as important as the iron and steel industry. SMS group is well prepared for this huge market and for growing future challenges. A large contribution here is the new joint venture PolyMet Solutions that was founded by SMS group and Mettop, an Austrian engineering company, with the objective to develop new technical solutions and to enhance customer value. The prices of nearly all metals have come under pressure during the past few years. Therefore, competitive technologies are regarded a crucial factor to achieve success in this critical market situation respectively to stabilize the market position.

Jan 1, 2019

By E. M. Hillary, D. F. Sangster

"Abstract - As a contribution to the World Minerals Geoscience Database Project, an index-level database comprising information on 142 SEDEX Pb-Zn deposits and occurrences was constructed in Microsoft Access 95 format. Although consisting of only basic information, the compilation, with full referencing of all data, is possibly the largest non-corporate SEDEX Pb-Zn database in the world. It thus provides an opportunity to make geoscience queries of SEDEX Pb-Zn deposits on a scale not previously available. This report provides a summary of the results of a few such queries both as a contribution to a better understanding of SEDEX lead-zinc deposits and as a demonstration of what even such a simple database can offer.During the compilation process, it became apparent that SEDEX Pb-Zn deposits could be assigned to one of the following three sub-types: Type 1 (53.5% of total) in which sulfide minerals are the only exhalative components; Type 2 (33.1%) in which the exhalative components are sulfides plus chert, siderite/ankerite, and/or barite; Type 3 (13.4%) which contains any components of Types 1 and 2 plus abundant iron-oxide minerals (commonly magnetite) and/or is associated with iron oxide-rich sedimentary rocks.Highlights of systematic queries of the database reveal that:1. a majority (84%) of the world’s SEDEX Pb-Zn deposits are not underlain by a discordant footwall feeder zone or vent complex;2. 63.6% of deposits occur in Proterozoic strata followed by a second peak in the Devonian (16.8%). Of those in the Proterozoic, 83% of Type 3 deposits occur in the Gondwanaland supercontinent, whereas only 42% of Type 2 and 39% of Type 1 are located in this large paleo-landmass;3. median (Pb+Zn) grades in Types 1 and 2 fall between 9% and 10% with a majority clustering within this range. Type 3 grades, however, range from ~1% to ~20% (Pb+Zn) with a median of 5%; 4. median size of Type 3 deposits is ~33 Mt, whereas Type 1 and 2 median sizes are ~7 Mt and ~8 Mt, respectively.The report concludes with a brief discussion of how an index-level database such as this can be used in conjunction with other, similar databases to reveal interesting and instructive relationships for guiding both research and exploration."

Jan 1, 1998

By J. Bouchard, A. Desbiens, M. Maldonado, R. del Villar

ABSTRACT: Despite many years of practical applications in mineral processing plants, the potential of column flotation has still not been fully exploited. The challenge in measuring some key variables is certainly an important contributing factor to this situation. Reliable online measurement of variables, such as the froth depth, bias, gas hold-up, frother concentration, bubble surface area flux, and bubble size distribution, provides opportunities for the application of various advanced control strategies and real-time optimization based on an economic criterion. For several years, Université Laval’sLaboratoire d’observation et d’optimisation des procédés researchers have been working on these opportunities. This paper describes the most recent advances and current research trends.

Jan 1, 2011

By D. R. Boyle

"The Murray Brook precious metal (Au, Ag) gossan deposit is one of nine supergene mineral deposits that have developed over polymetallic massive sulfide deposits in the Bathurst Camp of New Brunswick. Reserves consist of 1.9 Mt of gossan containing 1.53 g/t Au and 65.9 g/t Ag. The supergene zone at Murray Brook consists of six distinct units: a) altered massive sulfide, b) pyrite-quartz sand, c) massive sulfide gossan, d) disseminated sulfide gossan, e) ferruginized wallrock, and f) leached bedrock. The massive sulfide gossan constitutes the main body of economic mineralization and consists of goethite, primary quartz, secondary amorphous silica, K-Fe-Pb-As- Sb-Ag hydrated sulfate and oxide minerals (beudantite, plumbojarosite, jarosite, bindheimite, scorodite), trace cinnabar, and cassiterite of primary origin. The order of stability of sulfide minerals during oxidation was pyrite _ arsenopyrite _ galena _ Bi-Sb sulfosalts _ chalcopyrite _ tetrahedrite group _ sphalerite.Two mass balance techniques (isovolumetric and conservative element) indicate elemental depletion in gossan relative to primary ore in the order: S>Cd=Zn>Cu=Mn>Na=Ca>Fe=Al=V> Mg= K=Se=Hg>Pb>Ti>Ag>Mo=P>Ba; and enrichment in the order Au>As>Sb>Si>Bi. Tin, as cassiterite, is conservative.Mineralogic and paleomagnetic data suggest that the gossan deposit formed under a warm temperate climate throughout the Pliocene. The rate of oxidation and the compositional nature of the ore was significantly influenced by: a) the position of the primary sulfide zone in a downward moving hydrological system, b) primary sulfide composition and zonation that promoted the development of a strong electrochemical oxidation system, and c) pronounced intercalation of carbonate and sphalerite mineralization in sulfide zones, which promoted rapid development of secondary porosity, permeability and downward flow of oxygenated groundwater.During progressive oxidation and physico-chemical erosion of the gossan zone, Au was transported downward in groundwaters, probably as a Auo colloid complex, to be concentrated in the lower horizons of the gossan profile. The precipitation of Au was greatly increased in the pyrite/arsenopyrite zones. Gold concentration was multi-cyclic with continual dissolution and nucleation of the metal until final concentration in the void structures of the gossan. Leaching experiments and microprobe analyses indicate that Au is present in the gossan as submicron composite sols of Au-Ag-silica."

Jan 1, 1995

By D. R. Boyle

"Abstract - The Murray Brook precious metal (Au, Ag) gossan deposit is one of nine supergene mineral deposits that have developed over polymetallic massive sulfide deposits in the Bathurst Camp of New Brunswick. Reserves consist of 1.9 Mt of gossan containing 1.53 g/t Au and 65.9 g/t Ag. The supergene zone at Murray Brook consists of six distinct units: a) altered massive sulfide, b) pyrite-quartz sand, c) massive sulfide gossan, d) disseminated sulfide gossan, e) ferruginized wallrock, and f) leached bedrock. The massive sulfide gossan constitutes the main body of economic mineralization and consists of goethite, primary quartz, secondary amorphous silica, K-Fe-Pb-As- Sb-Ag hydrated sulfate and oxide minerals (beudantite, plumbojarosite, jarosite, bindheimite, scorodite), trace cinnabar, and cassiterite of primary origin. The order of stability of sulfide minerals during oxidation was pyrite > arsenopyrite > galena > Bi-Sb sulfosalts > chalcopyrite > tetrahedrite group > sphalerite.Two mass balance techniques (isovolumetric and conservative element) indicate elemental depletion in gossan relative to primary ore in the order: S>Cd=Zn>Cu=Mn>Na=Ca>Fe=Al=V> Mg= K=Se=Hg>Pb>Ti>Ag>Mo=P>Ba; and enrichment in the order Au>As>Sb>Si>Bi. Tin, as cassiterite, is conservative.Mineralogic and paleomagnetic data suggest that the gossan deposit formed under a warm temperate climate throughout the Pliocene. The rate of oxidation and the compositional nature of the ore was significantly influenced by: a) the position of the primary sulfide zone in a downward moving hydrological system, b) primary sulfide composition and zonation that promoted the development of a strong electrochemical oxidation system, and c) pronounced intercalation of carbonate and sphalerite mineralization in sulfide zones, which promoted rapid development of secondary porosity, permeability and downward flow of oxygenated groundwater.During progressive oxidation and physico-chemical erosion of the gossan zone, Au was trans- ported downward in groundwaters, probably as a Auo colloid complex, to be concentrated in the lower horizons of the gossan profile. The precipitation of Au was greatly increased in the pyrite/arsenopyrite zones. Gold concentration was multi-cyclic with continual dissolution and nucleation of the metal until final concentration in the void structures of the gossan. Leaching experiments and microprobe analyses indicate that Au is present in the gossan as submicron composite sols of Au-Ag-silica."

Jan 1, 1995

By Scott Rosenthal

?EMESRT History ?Design Philosophies (DP?s) ?Industry Successes ?Participation Thinking Differently Earth Moving Equipment Safety Round Table ? Use a critical mass to influence Marketing ? Define ?Problems?not ?Solutions? ? Leave the OEM designers to develop solutions Work within the companies to improve purchasing

May 1, 2010

By J. M. Hong, H. K. Zheng, R. Hu, C. B. Zhou

The Jinping-I double curvature arch dam, located in the middle reach of the Yalong River and with a maximum height of 305 m, is the world highest dam of the same type that has been completed. Since the second and third periods of the reservoir impounding, after which the reservoir water level was raised by about 200 m, a significant amount of leakage was observed out of the drainage holes deployed in the lowest drainage tunnel at the left-bank abutment at EL. 1595 m, with a pressure of 0.3 MPa at one typical hole when it was blocked. In this study, a number of analyses including water quality analysis, digital borehole imaging, tunnel geological mapping and in-situ groundwater monitoring were performed to investigate the source of leaking, the leakage passages and the performance of the grouting curtains. An inverse modeling procedure combining the orthogonal design, finite element forward modeling of the transient seepage flow, artificial neural network and genetic algorithm was invoked to further evaluate the permeability of the foundation rocks whose permeability was underestimated in design, using the in-situ measurements of flow rate and piezometric head. The geological structures that lead to the leakage were identified and the seepage flow behaviors in the dam foundation and the left bank abutment were assessed. Given the connectivity nature of the sub-vertically oriented fractures that induce the leakage event, it is found that some of the drainage holes with relative larger amount of discharge could be closed or blocked for reducing the amount of leakage without remarkably increasing the pore water pressure in the foundation rocks.

Jan 1, 2015

By Stanley G. Butcher

"The methods generally applied to predict performance and financially evaluate beneficiation options are reviewed.Typical costs f or a western Canadian thermal coal operation are examined. Preparation-from truck dump to loadout-frequently amounts 10 over a quarter of total minesite costs. Failure to achieve projected yield-whether caused by mine or plant problems-s-substantially increases production costs because more coal has 10 he mined to meet a specific market demand. Problem identification by mass/ash balances is recommended.Thorough characterization of the coal and associated waste materials and more reliable prediction of beneficiation process performance are therefore essential to determine a project 's financial viability.IntroductionWestern Canadian coal prep a ration plant capacity is partway through a massive expansion program . In 198 1 potential product ion was 14 million tonnes, by 1985 it will be 26 million tonnes per year. Only two years ago the industry was concerned whether it could sustain this rate of growth to meet market demands : now with diminished market demand and lower coal prices being offered by our international competitors there are doubts whether t his potential will be fully employed , even by 1990.One direct consequence o f the occurrence of a variety of coals in a stunningly beautiful but complex geo logical setting such as the Rocky Mountains and their Foothills is that each project is unique. Coal is a low value per tonne product. To supply distant markets from geographically isolated deposit s necessitates expensive , dedicated , infrastructure . T o be profitable these operations must achieve eve ry advantage of the economy of scale.Each of the mi ne complexes commissioned in the 1970s experienced severe problems in the area o f co a l preparation . Most bought their way out , paying for major plant modifications by increasing the scale of their total operation . The current market recession may not allow new operations this route to profitability.The objective of this paper is to illustrate the economic impact of coal preparation problems on the profitability o f the total minesite operation and thus provide a sound basis for decision making process."

Jan 1, 1985

By Robin Sheremeta

What is the goal of every organization when it comes to safety? Everyone Going Home Safe and Happy Every Day Good old days: Era of Death (accidents will happen) Era of Engineering: (Eg. hand rails, limitswitches, machine guards, etc.) Era of Legislation: procedures, laws and regulations (Eg. SWP?s, Mines Act) Era of Behaviour-Based Safety: (eg. STOP program)

May 1, 2010

By Yongquan Zhu, Zhengguo Zhu, Zhichun Liu, Chao Kong, Xinqiang Gao

"The aim of the study is to have a good understanding of the change in the seepage field during and after the tunnel excavation in weathering alteration rock. Field tests are used to monitor the changes of the water table and the numerical model is used to analysis the influence of the seepage filed with different operation conditions during and after the tunnel excavation. Results indicate that the depth, diameter and pumpage of precipitation well are the main factors that have a great influence on the drainage effect. Results also indicate that different operation conditions had various effects on the decrease in water yield during tunnel construction and the recovery in groundwater level after construction.INTRODUCTIONAs a potential disease during tunnel construction, Gushing water not only affected construction schedule, increased construction cost, as well as affected tunnel stability and safety during operation, but also decreased ground-water level. What’s more, the fall of water table caused by gushing water in tunnel would have influenced surrounding residents’ living water, agricultural water and ecological environment around tunnel. In recent years, enough emphasis has been paid to the influence on environment due to the construction of tunnel as a result of the reinforcement of people’s environmental protection awareness.As a result of water collection and drainage after excavation, groundwater was discharged into the tunnel, which caused a loss of water resources in the adjacent mountain mass. Furthermore, during tunnel operation, it was difficult for groundwater level to resume its original condition, which caused a bad ecological environment, because drainage system during tunnel construction destroyed its original hydrologic dynamic balance.In order to study whether decreased groundwater level resulting from tunnel construction could be restored during operation to its original condition, this paper gave a field monitoring on tunnel displacement during construction and simultaneously, generalized model of regional hydrogeology was created according to field hydrogeology to carry out a calculation of stable seepage flow and draw comparisons between recovery conditions of various water levels."

Jan 1, 2015

By Stephen Hardcastle

Supplying ventilation in underground metal mines can be one of the most energy demanding services required to support production activities. Consequently, as energy, in the form of electricity or combustible fuels can be expensive and their unit cost is expected to increase, there is significant interest in reducing the overall demands of a mine?s ventilation system through such initiatives as controlling ventilation based upon demand and exploring other power alternatives to the current usage of the diesel engine in mobile mine vehicles. However, determining the benefit of any energy saving technology is complex and not universal applicable across the industry, consequently they have not been widely adopted. For these technologies to succeed they must be strategically applied based upon sound business cases. The intent of this paper is to provide information on some of the prospective control strategies and their potential impact on the power consumption related to supplying ventilation.

May 1, 2007

By A. Allaire, J. Torrealba-Vargas, R. Welyhorsky

Early testwork was carried out to select the plant process design criteria and flowsheet selection. Additional testwork was carried out during the feasibility study to support the optimization of the plant design criteria. The test results showed that the recovery of gold was not very sensitive to grind size in the range of 75 to 105 microns. An additional result was that the presence of lead nitrate did not improve the kinetics of gold leaching. This conclusion was supported by the low content of sulphides in the ore. It was also found that the presence of lead nitrate increased copper dissolution, producing the potential for an increase of copper reporting to electrowinning, which is detrimental to the overall gold recovery process. The use of oxygen in leaching was investigated to increase leach kinetics. The results of leaching tests to compare using oxygen instead of air indicated that, due to the improved leach time, it was possible to reduce the number of leaching tanks from twenty four (24) to twenty (20).

Jan 1, 2011

By E. Asselin

Electrochemical polarization experiments were conducted on alloy 625 in ammonia solution between 25 and 225°C and the results were compared with those of an oxygen solubility model. Results confirm that corrosion is under oxygen control, Normalized corrosion rates are determined based on the rate of oxygen diffusion to the corroding surface, and the corrosion rate at 200°C (-9.7 µA.cm-2) is roughly 24 times higher than the corrosion rate at 25°C (0.4 nA,cm-2), An oxygen-solubility model for Supercritical Water Oxidation (SCWO) conditions was generated using the Redlich¬Kwong-Soave (RKS) equation of state, Results of the model confirm many of the experimental observations from SCWO reactors which suggest that corrosion is at a maximum at temperatures just short of the critical point, The RKS/oxygen diffusion model predicts that the corrosion rate at 365° C is ?85 times higher than the corrosion rate at 25' C. Given that a normalized corrosion rate is obtained, this type of model could be useful for selection of SCWO reactor materials.

Jan 1, 2005

Mine Safety in Chile ?Since the year 2000 fatality rate averages 34 per year ?1% of world mining labour force but 8% of world?s mining fatalities San Jose Mine Safety ?From 1998 to 2010 eight fatalities ?In 2003 mine inspectors recognized no second means of egress and a raise system was developed ?In 2006 182 workers were injured, 56 of them seriously ?In January 2007, there was a fatality after a rock burst, and the government ordered the mine closed ?Less than a year later the mine was back in operations. It had not complied with some of the basic safety measures ordered. One of those measures was to complete the escape way ladder.

May 1, 2011