Search Documents

By Hans E. Madeisky, Bruce W. Downing

Abstract-The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: anorthosite-hosted magmatic sulfide nickel, dunite-hosted magmatic sulfide nickel, porphyry copper-gold, and volcanic-hosted high sulfidation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray fluorescence equipment, already used for grade control at many mine sites, could provide the wholerock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By H. B. Farnam

"THE IRON ORE Company of Canada has been using do-it-yourself type explosives for three years. During the last 12 months we have used over 10 million pounds of ammonium nitrate-fuel oil explosives and either purchased or formulated one million pounds of slurried explosives.W e have been moving approximately one million cubic yards of stripping and ore per month and we expect our production rate to in-crease. Eighty per cent of our strip-ping and ore is soft enough to be blasted successfully with ammonium nitrate-fuel oil mixtures. Twenty per cent of our material is extremely hard and requires an explosive having greater strength than an AN-fuel oil mixture.W e had been using canned am-monium nitrate base explosives and TNT pellets to give maximum bottom loading density to fracture hard rock. As AN -fuel oil became widely used, it was apparent that other types of explosives could be formulated to fit our blasting requirements. Dr. M. A. Cook of the University of Utah was consulted regarding new explosives and together we developed the blasting slurries.Figure 1 shows a general view of one of our hard rock pits. The foot wall is on the right-hand side and this material is called iron forma-Figure 1.-General view of hard rock pitstion by our Company but is called 'Taconite by the operators on the Mesabi Range. This material runs 35 to 45 per cent iron and many pieces are hard enough to scratch glass. The formation is tilted at an angle of 55 degrees as can be seen in Figure 3.The bedding planes of this rock are about 24 to 36 inches apart and if the material is not well broken or fragmented, large chunks or slabs must be handled by the shovels which reduces shovel capacity and efficiency and increases maintenance costs."

Jan 1, 1960

By James McMahon

Although doubt has been expressed many times as to who first brought self-contained breathing apparatus to this side of the Atlantic, there is none whatever that the first organized station was established at Glace Bay, N .S., by the Dominion Coal Company, in 1907. This station was started with 20 sets of 1907 "Draeger" apparatus and all necessary station equipment and supplies. After the fire at No. 1 pit, Sydney Mines, in 1908, the Nova Scotia Steel Company installed 15 sets of "Draeger" and sup-plies, which were housed in a rescue car (a converted pull-man.) In 1909 or '10 a fire occurred at the Back Pit, Stellarton, where the apparatus from Glace Bay was used, and subsequently the Acadia Company erected a station and in-stalled 10 sets of "Securitas" apparatus. In 1912 the station at New Waterford was opened and equipped with "Draeger," and the same year the station at Springhill was built and equipped with the same type. Sometime during past years the Nova Scotia Steel Company acquired a couple of "Proto" machines, and after the explosion at the Allan shaft in 1918 the Acadia Coal Company added some "Gibbs" to their station. From this it will be seen that when the coal-fields were organized under the British Empire Steel Corporation the equipment was rather mixed, therefore steps were taken by the executive to stanardize the whole of the rescue and recovery work.

Jan 1, 1924

By Matthew R. Ward

This paper aims to describe the reasons and methods to extend enterprise networks into underground mines. Currently mines use a number of communication networks for telephones, PLCs, two-way VHF radio and computer networking. Each system can have different wiring, protocols, converters and interfaces all which require expansion and maintenance. The convergence of voice, video and data using Ethernet and TCP/IP has the very real benefit of one ?wire? for underground networks. Now that the majority of underground equipment can communicate using TCP/IP, network convergence can offer reduced network expansion and maintenance costs. Cost savings are good, but the truly exciting aspect of network convergence using Ethernet is the low-cost, high speed wireless networking now available . These wireless networks offer an opportunity to facilitate mining automation even on a small budget. How would mine operators change they way they operate if they could gather vehicle location and data in real time? What about controlling equipment remotely? The list of applications is long and includes traffic control, dispatching, real-time ore blending, tele-operation, automated production reporting, vehicle health monitoring, elimination of paper forms and immediate network access for surveyors and geologists. An ideal converged network for underground mining would be robust, inexpensive, easy to expand, enable fast and secure connections while keeping voice communication performance equivalent or better than what is now provided by VHF radio

Apr 1, 2005

By E. W. Williams

THE Ontario Research Foundation has developed a process for producing low-density steel shapes by direct reduction of iron oxide powders. The process is a combination of reduction, sintering (without compaction), and carburizing, and has been described by Cavanagh (1). Iron oxide powder, in the form of mill scale or highly concentrated iron ore, carefully sized, is poured into a porous mould. A reducing agent, generally coke breeze, is placed around this mould in a heat resistant sagger which is sealed off and heated to 2,000°F. for a number of hours. The coke/ ore ratio, the particle size distribution, the temperature and time of soaking, and the size and shape of the reduced product, determine the densities and carbon contents attained. The Defence Research Board sponsored a programme of research into some of the mechanical properties of the material (which was named Controlled Density Steel) and this paper is an account of various factors which govern the tensile strength of the steel. The ?practically attainable range of density is from 1.5 to 5.5 gm./ cc. but higher densities are obtained on hot working. This paper, however, is restricted to discussion of results for moulded products.

Jan 1, 1957

By R. P. Nicholson

On September 3rd, 1947, the Acadia Coal Company put into operation a central coal preparation plant. This plant was designed to process all coals mined by this Company in the Pictou County coal field. The problem, briefly, was to make a three-way separation of the raw coal fed into the plant. It was desired to remove all stone, metal, and wood from the marketable coal and to produce a splint coal from the raw material which would be suitable for making power. This splint coal product is belted directly to the power plant which is adjacent to the wash plant. To attain this object it was therefore necessary, first, to wash the raw coal, removing all splint, stone, metal, and wood. The stone, metal, wood, and highest-ash splint had then to be removed by a second washing in order to obtain the lower-ash splint for use in the power plant. The plant is on the east side of the Allan colliery, in the town of Stellarton (see accompanying photograph). It is of steel frame construction with wood siding, covered on the exterior with corrugated galvanized iron. Considerable concrete had to be poured for the foundation piers as the plant site is largely 'fill' ground. This necessitated the construction of extremely heavy footings containing a large amount of reinforcing steel. In all, 884 cu. yds. of concrete were poured for the various pits, tanks, and foundations; its average test was about 3,500 lb. per square inch. At the time the plant was constructed, the steel shortage in Canada and the United States was acute and, in order to obtain steel for the structure which is four stories high- an unused part of the Allan bankhead was torn down. Enough steel was obtained from this demolition to fabricate the new plant.

Jan 1, 1948

By Michael T. McCaffrey

The wide range of potential feed materials, process steps, and products in metallurgical facilities means that standard equipment might not be available to adequately meet the project technical and economic needs. Custom designed equipment should be considered only after rigorous research precludes purchasing standard equipment. However, the decision to use custom equipment introduces a new element of risk into the project. To manage the risk, custom equipment design should be developed through the same front end loading (FEL) phases as project development. If more than incremental development of custom equipment is required, appropriate test work or pilot trials are required to test key uncertainties. Important activities during custom equipment design include maintaining clearly defined performance objectives, conducting appropriate reviews, carefully crafting commercial and intellectual property agreements with design and fabrication partners, and assembling a multidisciplinary team with sufficient development expertise.

Jan 1, 2015

By D. B. Smith

DURING the summer of 1953, test work commenced at the Sullivan Concentrator with a view to the modification of filtration practice by the inclusion of wet cyclone classification of the lead concentrates, with separate filtration of the underflow and overflow products. Formerly, practice was conventional and the equipment employed comprised one 50-foot diameter thickener ?with the underflow routed via a 20-foot stock tank to two 8-foot by 12-foot Oliver filters. Heating of the filter feeds to 40° C. and the use of mechanical slappers on the filter drums ?have both been standard features of Sullivan practice for years. Both of these have been retained. Currently (February, 1956), lead concentrates are being classified into sands and slimes by 12-inch cyclones with the underflow, at 75 per cent solids, being fed to No. 1 Oliver filter. The overflow is thickened to 75 per cent solids and filtered separately by a No. 2 Oliver filter . The tonnage split is approximately two of underflow to one of overflow. The overflow contains 75 to 80 per cent of the total minus I 500 mesh slimes in the feed.

Jan 1, 1956

By W. G. Hubler

It has been within only the last two or three years that enough progress has been made in preferential flotation to warrant metallurgists in recommending the installation of commercial-sized plants for the treatment of copper-zinc-iron ores. Until the new processes had been worked out successfully, the treatment of this type of ore had proved a stumbling block in the path of metallurgical progress. Separation of lead-zinc ore is comparatively simple. A lead-zinc ore low in iron may be separated and concentrated by gravity con-centration, provided it is not necessary to grind too fine. Owing to the specific gravity of chalcopyrite and sphalerite being so nearly the same, however, their separation by gravity concentration is out of the question. Complex lead-zinc-iron ores in which the several minerals are intimately associated, requiring fine grinding to free them, have been successfully treated by flotation for the past fifteen years. Galena is easily floated, and its flotation, unlike that of chal¬copyrite, is not affected by the reagents used to inhibit the flotation of sphalerite and iron sulphides. When an attempt was made to use the methods of lead-zinc se-paration on copper-zinc ores, it was found that the depressant re-agents added to inhibit the flotation of the iron and zinc minerals would, under certain conditions, depress a large part of the copper. It was also recognized that, in the grinding of copper-zinc ore, soluble salts were generated which were detrimental to flotation unless properly controlled. The main part of this paper will be a discussion of solutions in the grinding circuit in relation to the pro¬duction of soluble salts and their effect on flotation.

Jan 1, 1931

By Louis Cabot

A pilot plant of the Modular Gold Processing Unit (MGPU) was designed, installed and operated, over a 8 months period, by RSW-Béroma, at the Granada Mine located near Rouyn-Noranda, Quebec. A description of the project geology, plant set up as well as exploitation results, including productivity and profitability curves, are given for a small scale mining operation in comparison with larger ones. Copyright ã 2001 CIM

May 1, 2001

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively. INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By J. B. Morrow

Methods of Coal Preparation Fundamentally, the object of coal preparation is to increase, economically, the value of a fuel by making it more suitable to the uses of the consumer. This can be accomplished in three major ways: 1.Screening or sizing 2.-Mixrng or blending 3.-Cleaning By combinations of any or all of these methods we can prepare coal to meet standard specifications-a process of standardization which is the more desirable the more nearly it approaches the unvarying quality of packaged goods, where the package you buy today and tomorrow is the same as that you bought yesterday. It should be noted that it is readily possible to get good cleaning and still have poor preparation because of faulty screening and mixing, and, on the other hand, it is possible to get a passable grade of cleaning, combined with good screening and mixing facilities.

Jan 1, 1931

By R. Matusewicz, A. Kaye

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in non-ferrous applications, including the processing of lead and zinc primary concentrates and secondary (post-consumer) materials. TSL is highly flexible and efficient, and is one of the few technologies which can process primary and secondary feeds, and use varying fuels, to deliver high recoveries and excellent environmental performance. With the recent high value of both lead and zinc, and an escalating awareness of the sustainable use of resources, focus on the processing of secondary feed material sources has surged. Ausmelt Technology has proven to be well suited to the economic recovery of values, with twenty-two (22) Ausmelt furnaces processing lead and zinc bearing feed sources now in operation, under design or construction. This paper describes Ausmelt's progress in the fields of lead and zinc processing, and developments in new processing areas such as EAF dust processing and linking to innovative hydrometallurgical technology. Ausmelt has recently committed to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This project is due for start up in the first quarter of 2008.

Jan 1, 2008

By N. H. J. Freire, D. Majuste

In this paper, the effects of some organic compounds on the current efficiency, cell voltage and specific energy consumption during nickel electrowinning, and on the deposit features (morphology, crystallographic orientation and nanohardness) were described. The organics tested here (extractant, diluent, flocculant, lubricating oil and acid mist suppressant) are currently used in industrial plants. The results indicated that only the flocculant and acid mist suppressant exhibit relevant negative impacts on the current efficiency and energy consumption. The current efficiency dropped from 93.6 % (organic-free solutions) to 86.0 % and to 92.8% in electrolytes containing 100 mg.L-1 of acid mist suppressant and flocculant, respectively. At this concentration, their addition to the electrolyte led to increases of the specific energy consumption in the order of 18 % (acid mist supressant) and 2 % (flocculant). Cyclic voltammetry showed that Ni nucleation occurs at more negative potentials at 50 and 100 mg.L-1 of these organics in the electrolyte, thus indicating an inhibition of the deposition process. The deposit quality decreased at the higher concentration of all organics, when more hydrogen pitting was observed. The acid mist suppressant caused delamination of the Ni deposit at 50 and 100 mg.L-1. The addition of 100 mg.L-1 of flocculant and acid mist suppressant to the electrolyte increased the nanohardness of the deposit around 31 and 72%, respectively. The increase in Ni deposit hardness may lead to a decrease in the material ductility, thereby affecting the stripping and cutting of Ni sheets. Our findings may be helpful since strong adverse effect of some organics that may be present in the electrolyte were identified, thus the industry can control and optimize the organic´s dosage in the corresponding operations.

Jan 1, 2016

By J. B. Mitchell

Many of the pre-production and plant startup problems that we regard as inevitable are actually caused by poor organizational methods. Traditional methods of organization can be modified to provide clear definitions of responsibility, continuity and depth of involvement of key personnel in order to overcome these problems.

Jan 1, 1966

By E. Asselin, P. Sauve, H. Salomon-de-Friedberg

"Residues from the CESL Copper process were leached using the CESL Gold process. The kinetics of reaction were confirmed to be fast with over 50% of the gold consistently extracted within 2 minutes of leaching. Final gold extractions under the conditions tested here were between 80-90% obtained within 90 minutes. A model for the CESL Gold process was developed. This model is slightly different based on whether the copper concentrate leach residue was ground or unground prior to leaching: the gold leaching rate constant is approximately twice as fast for the ground samples. Unground residues had a P80 of 13 ?m whereas ground residues had a P80 of 10 ?m. The model predicts a 43% decrease in leaching time for ground residue versus unground residue to achieve the same extraction under otherwise identical conditions. The model was more accurate for the ground samples. INTRODUCTIONTeck's CESL Process (Jones, 1996) was developed to provide an economically attractive alternative to traditional copper smelting. It has since evolved to also deal with copper concentrates containing valuable impurities such as nickel and undesirable ones, such as arsenic, while reducing downstream costs. Effective recovery of gold and silver is essential to the economics of the CESL Process. The Brook Hunt 2007 copper concentrate assay data (Wood-Mackenzie, 2007) were examined to determine the ratio of gold plus silver value relative to the contained copper. As indicated in Figure 1 below, nearly two-thirds of concentrates have 10% or more of their total value tied up in their precious metals content.CESL has extensively examined the recovery of gold and silver at bench, pilot and demonstration scale, which has culminated in the present CESL Gold Process (Barr et al., 2007). The process targets the precious metal contained in the leach residues produced in the copper portion of the flowsheet. This residue has two primary components which influence downstream processing. The major iron-rich fraction (-75 wt%) of the residue is a mixture of various forms of iron oxide precipitates including hematite and jarosite (Sahu and Asselin, 2011). The iron fraction ranges from amorphous to crystalline in nature depending on the compound precipitated, upstream operating conditions and feed material composition. The lesser, but by no means less important, fraction is a mixture of elemental sulphur and unreacted sulphides (principally pyrite).Elemental sulphur formed during the oxidative leach of the copper concentrate reacts with cyanide to form thiocyanate (SCN-) making a traditional cyanide leach approach too costly. Since the SCN formation reaction strongly depends on contact time with the CESL residues (Po, 2007) short contact times were preferred. This factor guided the development work towards the eventual room temperature, pressure cyanidation process which results in near complete gold dissolution in 90 minutes. A recent CESL gold demonstration campaign treating 1.5 t/d of residue from the copper oxidation step achieved an average gold extraction of 91% (96% maximum)."

Jan 1, 2012

By Stephen G. Mlot

The evaluation of mineral projects involves the identification, mitigation and management of significant uncertainty. Benchmarking is an essential and effective way of increasing confidence and reducing uncertainty associated with input parameters and assumptions. Comprehensive and detailed benchmarking will ensure ?best practice? technologies, methods and systems have been considered and that the appropriate practices can be identified and incorporated into the project. In conjunction with the involvement of experienced industry practitioners, benchmarking is best employed throughout project evaluation to enable early identification of ?errors?, producing more accurate and predictable outcomes. Considerable time and effort is required to gather data and information, which should be benchmarked by the project evaluation team. There is a history of mining projects underperforming, on production, on costs and on return to the investors. The quality of mine plans and feasibility studies, and the quality of the input data is being questioned in many ways. Benchmarking assists sound project evaluation practices, by providing a database of actual results, to validate project inputs and outcomes, ensuring they are realistic and achievable. Benchmarking also provides unbiased, statistical support as the basis for sound investment decision making and ensures well considered decisions are made resulting in a more efficient study process. The evaluation of the quality of projects which are the subject of transactions also benefits from the use of real data obtained from a benchmarking database. Vendors are quick to highlight the benefits of their projects, and conceal the flaws, inflating the value. Buyers will want to quantify the potential of a project through the due diligence process relying on actual results from benchmarking. For the reasons broadly outlined above, benchmarking should be considered as an essential component of effective Project Evaluation.

Aug 1, 2013

By J. J. Baz-Dresch

"The Cannon Mine, a joint venture between Asamera Minerals (the operator) and Breakwater Resources, is located in the centre of Washington state at the eastern base of the Cascade Mountains. The mine complex is located three blocks south of the city limits of Wenatchee, part of an urban area with a total population of 47 000. The closest residence is 350 feet from the mine portal.The B-Neath zone is a narrow, high-grade, downward extension of the southern tail of the mine's main ore body, the B-North zone. It also underlies the northernmost portion of the B-West zone (Fig . I) . The ore is usually reasonably competent but completely surrounded by very weak rock consisting of shear zone and unsilicified sandstones and siltstones.The zone has maximum dimensions of 420 ft in thickness, 500 ft in length , and 200 ft in width . The economic reserves extend from the 70-ft elevation (elevation above sea level) to the 630-ft elevation and consist of about 1.3 million tons of geologic reserves (proven and probable) at an average grade of 0.33 ounces per ton.Acquisition and ExplorationInitial DiscoveryThe initial discovery of the B-Neath zone was made by Tenneco Minerals during July through September, 1984. Their 22-hole surface drilling program consisted of 18 200 ft of drilling. Tenneco Minerals had acquired the 91/2 acre lease from United Mining Corporation.Asamera Minerals subsequently purchased Tenneco's lease in July, 1985; Tenneco retained a royalty position which was later purchased by Echo Bay Mining.Follow-up drilling by Asamera Minerals consisted of both surface and underground drilling. Eight surface holes (7200 ft) were drilled commencing in December, 1985. Following evaluation of the geologic data, an access drift was driven on strike along the top of the ore zone on the 500 level. Diamond drilling from this platform consisted of 17 200 ft in 79 holes."

Jan 1, 1990

By James D. Bamburak

Total mineral production in Manitoba has averaged C$1 billion over the past ten years. Industrial mineral production has comprised almost 10% of the total, with more than half coming from the aggregate sector. In southeastern Manitoba, tantalum, spodumene and amblygonite concentrates, cesium and rubidium ores, cesium formate, dimension stone and sphagnum peat moss are produced. Gypsum, high-calcium limestone and lime are produced in the Interlake area. Early industrial mineral production consisted of tools and implements, salt and pottery. Historical production has included: salt, building stone, aggregate, lime and dolime, lignite coal, gypsum, natural and Portland cement, calcium bentonite, brick, light-weight aggregate, caustic soda and soda ash, and silica sand. Future industrial mineral production may come from reactivated quarries, pits and wells or from new producers of current commodities. Newproducts may include: stainless steel master alloy, silicon metal, titanium and magnetite, lithium carbonate, float-plate glass and ferrosilicon, "marble" dimension stone, magnesium metal, potash and kaolin.

Jan 1, 2001

By E. Brzychczy

Artificial intelligence techniques are ever more frequently implemented in the modern world. One of their numerous uses is supporting enterprise management. Intelligent techniques and intelligent information technology (IT) systems can be implemented in mining-related issues as well. The author of this article concentrates on supporting the process of planning mining operations by intelligent systems and techniques. The author also underlines the importance of knowledge accumulation in a mining enterprise (especially tacit knowledge) as well as its efficient storing and using. Additionally, the author provides a short description of characteristics of intelligent IT systems and indicates their capabilities in planning mining operations. She presents two solutions, namely: an advisory system which supports the process of planning preliminary works and exploitation works in hard coal mines, and a method of modeling and optimizing mining operations. Finally, the author indicates a few possible future development trends of intelligent systems - the intelligent systems of decision support.

Aug 1, 2013