Search Documents

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

By Alfred Annor

Deep mining requires innovative approaches in ground control technology and the search for new ground support materials including backfill. There is a need to look at mine waste materials that may be available in deep mines to assess their suitability for use as composite backfill. Composite materials are widely used in all areas of engineering because of their unique and often superior structural properties compared to those of the singular constituent materials. Over the past few years, there has been a growing interest towards the investigation and use of various types of composite backfill materials as special applications fill in mines. A research project is being conducted at CANMET- Mining and Mineral Sciences Laboratories, Natural Resources Canada, to investigate the properties of potential ground support materials for use in deep mines. As part of this investigation, composite backfill materials were prepared by combining waste rock aggregates and mill tailings in various ratios, to determine their optimal mix proportions for strength development. A few cemented rockfill and straight tailings paste backfill samples were also prepared and were used as controls for the study. Two sample sizes were used for the investigation in order to evaluate the scale effects on the material behaviour. A set of samples were cured at 44 EC to simulate the anticipated temperature conditions in deep mines. A second set of samples were cured at 23 EC to provide engineering reference data. The test results show that compared to either the cemented rockfill or the straight tailings pastefill material, the composite backfill samples were the strongest and stiffest of all the test materials investigated in this study. The composite backfill samples also produced the lowest void ratio and porosity values compared to the cemented rockfill and the straight tailings backfill material. This paper will present the results of the laboratory investigations to date. It will also outline the on-going work at CANMET - Mining and Mineral Sciences Laboratories to further assess the ground support potential and viability of using composite fills in deep mines.

May 1, 2003

By U. Dillon, G. Blackwell

"Geographic information systems (GIS) provide an efficient means for the recording, manipulation, revision, display and analysis of spatially referenced data. GIS are widely used at the exploration stage of mine development, and are increasingly used for reclamation planning. The ability of a GIS to perform spatial searches and query spatially referenced data make it a powerful tool for use at all stages of mine development. As the amount of data available for analysis increases, so does the power and flexibility of GIS as a planning tool.Starting from the exploration database, this paper describes how a GIS can be used for the development of mining plans based on topography, geology and mineralization information stored in a relational database. Planning decisions approaching the optimal can then be made for a wide range of parameters, including stockpile and waste dump locations, the location of potentially acid generating and neutralizing material for dump design, profitable and risk-controlled mine extraction sequencing, and haul road locations. This is made possible by the overlay and buffer analysis capabilities of a GIS which are explored and exploited to produce a continuous mine production planning program, as well as site remediation and reclamation using a successful case study. IntroductionGeographic information systems (GIS) are a relatively new tool in the mining industry. Although they have existed for a number of years, the potential of GIS for mine management and planning is only beginning to be investigated and exploited. The unique spatial capabilities of GIS make them particularly wellsuited for use in mining, where spatial information is fundamental to the processes of mineral exploration, mine development, and environmental reclamation. A number of potential applications for GIS in the mining industry have been identified, and they are widely used for exploration and reclamation. The use of a GIS as a platform for the development of mine planning routines and software remains an interesting, but as of yet unexplored, application of this technology."

Jan 1, 2003

By A. Kapoor, L. Morin, S. Mortazavi, P. Béedard, Gould. W. D., A. Kuiper

The degradation of thiocyanate in a simulated gold mill effluent was studied using a laboratory scale rotating biological contactor (RBC). Complete SCN- removal was obtained at temperatures of 8 and 12°C, and a hydraulic retention time of approximately 3.3 h. The NH4+ produced by thiocyanate hydrolysis was oxidized by nitrifying bacteria to NO2 and NO3-. The HS- produced by thiocyanate hydrolysis was chemically and biologically oxidized to elemental S, which was subsequently biologically oxidized to sulfate. Incomplete sulfur oxidation occurred in the RBC, particularly at 8°C and elemental sulfur deposition was observed on the RBC disks. The RBC feed exhibited toxicity to rainbow trout but the RBC was effective in removing the acute toxicity of thiocyanate.

Jan 1, 2005

By Jean-François Lessard

The performance of rock pass systems has a significant contribution to the economics of underground mines. Operational concerns include hang-ups due to arching of material, blockage and degradation of the rock pass. This papers presents the preliminary results of a comprehensive rock pass database on the engineering and operation of rock pass systems in Quebec underground mines.

May 1, 2002

By J-F. Béland, N. Parson

Aluminum extrusions are widely used for automotive crash management systems due to their superior specific energy absorption capabilities, as compared to steel. The Al-Mg-Si alloy series can be readily extruded into complex multi-hollow profiles, as required in crash systems, and can be used to target a range of desired strength levels. This paper focuses on the development of an axial crush test protocol and evaluation of the crush performance of common 6XXX series alloys for a variety of tempers. The observed crush behaviour is then compared to tensile test results.

Jan 1, 2015

By B. V. Knelson

"GENTLEMEN:This paper will deal with centrifugal separation - theory and practical, and since the Knelson Concentrator is the only centrifugal concentrator with a properly fluidized bed, this paper will cover the Knelson Concentrator and its technical and structural advances over the last five years. As I am the person with the most experience in this line, I guess I am some kind of an expert; what kind I’m not sure, but some kind.This type of concentrator truly was developed because I’m lazy and I constantly look for easier ways to do things. My experience in the mining industry was very limited but I did realize in looking at placer operations, which is the application where I spring from, that it was tremendously labour intensive and my first reaction that ""my god, there must be some method or way-of handling product in a more efficient (and you can read that as being able to quickly recover very fine particle gold) way than was being shown at that time"". So, the Knelson Concentrator was born - about 6 or 7 years later. Our first attempt was a cone with about the same degree of slope as our present machine and since we had no knowledge of vibration dampening and centrifugal forces at that point, it was just an idea that this should work.Our first run was one of twenty minute duration. We did make that first machine variable speed by a mechanical belt system and we found that at about 240 rpms we were virtually shaking the gravel plant apart that we were attached to. So the first run was twenty minutes and back to the drawing board. However, that first run produced a concentrate so superior to anything we had seen previously, that we knew without any question, we were definately and accurately on the right track."

Jan 1, 1985

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By W. van der Merwe

ABSTRACT With the gold industry processing more complex ores, the online measurement and control of cyanide addition to the gold leaching circuit has become more critical. This paper compares the two commonly employed ‘free’ cyanide online analysis methods (amperometric and potentiometric endpoint silver nitrate titration) with the rhodanine endpoint silver nitrate titration and ion selective electrode methods common at site laboratories. Measurement differences between these methods are presented and discussed for cyanide solutions containing copper and zinc with varying cyanide to metal ion ratios. The resulting cyanide available to leach gold is also compared using these measurement techniques.

Jan 1, 2013

By D. L. Putnam

Snap Lake Mine ?? Complex dyke ore body ?? Underground operation ?? 1.1 million tonnes per annum ?? 1.2 carats per tonne ?? On-site diesel power generation ?? Supply by ice road and air ?? Milestones ? Construction commenced in 2005 ? Commissioning 2007 ? First diamonds August 2007

May 1, 2008

Safe underground mine backfilling with hydraulic fill requires efficient fill drainage and stable fill retaining walls or bulkheads. If any or both the above two requirements are not satisfied, such a backfilling operation creates unsafe conditions and may lead to backfill retaining wall failures. Mine backfill retaining wall failures are always associated with economic losses, fatalities and interruption to mine production. Mining industry wants to either reduce or eliminate these fill retaining wall failures. The fill retaining wall failures could be effectively avoided through the use of fibre reinforced shotcrete fill retaining walls and engineered drainage systems through the retaining walls. This paper presents the experience of the author in developing, implementing, and monitoring several hundred fibre reinforced shotcrete fill retaining walls at a mine in Australia with the highest safety standard. The details on the mine backfill drainage system and fibre reinforced shotcrete fill retaining wall designs are also presented.

May 1, 2007

By K. Dinh

The Ground Penetrating Radar (GPR) has been studied for a long time as a non-destructive evaluation (NDE) technology for inspection of concrete structures. Currently, the most widely used technique for interpreting GPR data of concrete bridge decks is the one that based on the amplitudes measured at various interfaces such as asphalt-concrete, top rebar, or slab bottom. The assumption behind this technique is that a sound concrete deck should have the same reflection amplitude at these interfaces while any low number would indicate some sign of deterioration. Unfortunately, this assumption is not completely valid in most cases. As a consequence, the reported test results usually do not reflect real condition of concrete bridge decks in question. The main goal of this paper is therefore twofold: (1) to discuss the limitations of the amplitude analysis method, and (2) to propose a new model that interprets GPR data of concrete bridge decks. The model methodology is based on the comparison of GPR A-scans between two inspections, using the so-called correlation analysis. The results, indicated by the correlation coefficients, are then employed to develop a contour map that estimates different levels of deterioration. The model is then implemented to a case study in order to illustrate its methodology.

Aug 1, 2013

By L. Frost

"Since the late 1990s, increased prevalence of severe lung disease among US coal miners has been observed, particularly in central Appalachia where thin-seam mining is prevalent. While respirable silica exposures have been implicated in many cases, the available dust monitoring data from mines shows no explanatory trends. One possible factor could be differences in the relative toxicity of silica particles based on their surface condition. Previous research has indicated that particles with occluded surfaces (e.g., by a thin layer of clay) may be less toxic than those with non-occluded surfaces. However, this dust characteristic has not been investigated before now in central Appalachian mines. In the present study, 18 respirable dust samples from seven central Appalachian mines and two northern Appalachian mines were analyzed to assess the relative occurrence of surface-occluded silica. Results showed that the dust from central Appalachian mines actually had higher fractions of occluded silica, which may be due to extraction of large amounts of rock strata along with the coal. However, the central Appalachian mines also more silica particles overall (i.e., occluded + non-occluded) in terms of total number percentage of respirable particles.INTRODUCTIONResurgence of occupational lung disease among US coal miners, especially in the central Appalachian region, has been observed since the late 1990’s (Gibson, 2016; Zosky et al., 2016; Suarthana et al., 2011; Gamble et al., 2011; Antao et al., 2005; Attfield & Sexias, 1995). In addition to increased prevalence of simple Coal Workers’ Pneumoconiosis (CWP, or “black lung”), the prevalence of severe and rapidly progressive disease has risen dramatically (Almberg et al., 2018; Blackley et al., 2018a, 2018b, 2016, 2014; Graber et al., 2017; Cohen et al., 2016). While exposures to respirable silica have long been known to cause or play a role in diseases such as silicosis or progressive massive fibrosis (PMF), which is conventionally considered as the most advanced form of CWP, it is unclear whether silica is the only culprit in the recent outbreak of severe disease. Indeed, as disease rates have risen, both total respirable dust and silica concentrations generally appear to have declined since the late 1980s, based on regulatory monitoring data in the most affected mining districts (i.e., MSHA coal Districts 4, 5 and 12, which cover central WV, eastern KY and southwestern VA, and southern WV, respectively) (Figure 1). Of course, the latency of disease can vary and may be or more 10 years, but many of the most recent cases are likely to have resulted from exposures that occurred since the late 1980s."

Jan 1, 2019

"In a continuing investigation into the development of uranium alloys for armament applications, some complex base alloy corn positions were modified by varying the amount of alloying elements and by removing one or two of the alloying elements in turn from the base alloys. These uranium-base alloys were specially formulated in a search for heat-treatable, high-strength, ductile, high-density alloys. All alloys studied were ternary, quaternary or more complex alloys of uranium with molybdenum, zirconium, niobium and vanadium. Each cast alloy was studied under three different heat-treatments, and its mechanical and corrosion properties were determined. It was found that although most of the alloys studied had the hardness and strength required, they were extremely brittle and notch-sensitive under tensile stresses."

Jan 1, 1968

By M. J. H. Ruscoe

"The circulation wear rates of pure nickel, cupronickel and nickel-plated-steel coins were measured and found to be in the ratio 1:3:1 . The relative wear rates of nickel and cupronickel coins were similar to those reported in earlier studies, and the circulation wear data for nickel were used as a reference in laboratory wear tests. A correlation between circulation wear rates and laboratory wear rates formed the basis for a prediction of service life using relief legibility as an 'end of life' criterion. This criterion was determined to be an average surface thickness loss of 12 um. The surf aces of nickel and Nickel-Banded-Steel (N-B-STM) coins were observed to harden both in circulation and in the laboratory tests at a rate of approximately I VHN/year of actual or simulated service life. It was also observed that the laboratory wear rate of N-B -S coins increased as nickel cladding thickness increased and this effect was attributed to differences in surface hardness.Wear test results are also reported for the new Canadian dollar coin material which shows a better wear resistance than pure nickel. IntroductionThe subject of coinage wear has a long history, and a number of studies have been published, concerned both with the measurement of circulation wear rates and with accelerated laboratory tests to simulate the behaviour of coinage materials in service. As early as 1803, wear tests were conducted by Hatchett on gold coinage using various types of vibratory and tumbling machines». These tests were commissioned by King George III of England who was concerned about the wear of gold coins in circulation.Early in this century, Adrian performed laboratory tests that showed that the wear rates of cupronickel 75/25 and nickel coins were in the ratio 3:1 and this ratio was later confirmed in laboratory tests reported by Daeppen and Zurrerw, The latter authors also weighed cupronickel and nickel coins that had been in circulation for various times and observed the same 3: I ratio. There was further support from Tylczak and Blickensderfer who reported significantly higher abrasive wear rates for cupronickel compared to nickel, when rubbed against sand paper."

Jan 1, 1988

By M. E. Coleman, G. Money

Pneumatic Conveying and Process Injection Technologies have been implemented in the metals markets for the last 40 years and have considerably improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider has turned its attention to supporting the Metals Market. Clyde seeks to utilise its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries.

Jan 1, 2008

By Jeffrey L. Pagnutti

Train derailment can lead to loss of capital, damage to the environment, and loss of life. Machinery condition monitoring techniques can be used to develop a structural health monitoring system for railway track to detect faults at the incipient stage, before catastrophic failure occurs. This study uses vibration measurements from a novel material haulage unit to develop a decision support system for railway track maintenance. A variety of feature sets and classifiers were compared to determine the optimal configuration for fault detection. The results highlight the shortcomings and advantages of certain methods and describe the process in which the optimal result was obtained. The Parzen data descriptor paired with a refined statistical feature set performed the task of fault detection with less than five percent false positive and false negative classification error. Overall, the outcome of these experiments indicated that condition monitoring of railway systems is a promising approach for fault detection and has the potential to avoid catastrophic failure.

May 1, 2013

By Michel Aubertin

Les haldes à stériles contenant des minéraux sulfureux réactifs constituent un milieu favorable à la production du drainage minier acide (DMA). Au sein de ces haldes, les processus physiques, géochimiques et biologiques qui mènent à la production du DMA sont nombreux et complexes. Un des aspects critiques qui affecte la génération de DMA est la distribution et le mouvement de l?eau dans les roches stériles. La modélisation numérique est un outil qui permet de comprendre, pour éventuellement contrôler, les mouvements de l?eau (et donc réduire la production du DMA) dans les haldes pendant la période d?exploitation de la mine et à sa fermeture. Plusieurs simulations numériques des écoulements non saturés dans des haldes ont été effectuées. Pour ces simulations, on a considéré divers types de matériaux, diverses conditions atmosphériques et diverses configurations géométriques. Les simulations réalisées montrent que l?on peut contrôler les mouvements de l?eau en introduisant des couches de matériaux fins intercalées dans les haldes formées de matériaux grossiers. Des couches horizontales ne sont cependant pas appropriées puisqu?elles peuvent, dans certains cas, favoriser la création de zones humides susceptibles d?amplifier les effets du DMA. Une faible inclinaison des couches de matériaux fins vers l?extérieur permet de palier à ce problème. Les couches inclinées favorisent un drainage des haldes vers la périphérie. Ceci a pour effet de garder sèche une grande partie des stériles et de réduire, par le fait même, la production du DMA.

Nov 1, 2002

Discovery of an economic diamond deposit produces considerable wealth in terms of jobs, royalties, mining investment, and economic spinoffs for residents, including Aboriginal peoples. Diamond mines contribute to the GDP, increased personal income per person and reduced unemployment rates. Is it possible in Alberta?

May 1, 2008

By Hamid Mahmoudabadi

In the present paper, the performance of four approaches based on neural networks and geostatistical method for grade estimation are compared and analyzed their performance to find a proper method. Four methods, Multi Layer Perceptron neural network (MLP), Radial Basis Function (RBF), General Regression Neural Network (GRNN) and Ordinary Kriging (OK) are selected for ore grade estimation of variable Fe in an iron deposit located in Iran. For each method, two diagnostic statistics are calculated: Mean square error (MSE) and correlation coefficient. The results show the superiority of the General Regression Neural Network.

Oct 1, 2009