Search Documents

By Marsh S. Watson, Robert A. Howard

An electrolytic model study has been made of the relative productivity of perforated casing. The results show that the relative productivity is roughly one-half to two-thirds of that predicted from point-sink calculations. This discrepancy can he satisfactorily explained on the basis of casing interference. The relative productivity was found to he insensitive to spatial arrangement of the perforations. INTRODUCTION The relative productivity of wells with perforated casing has been treated mathematically by Muskat.' In his treatment the perforations are represented by small spheres, thus enabling him to approximate the flow by that to point sinks. By neglecting interference between the flow into the various spheres representing the perforations, one may deduce the approximate formula Qu 1/rp - 1/rw • (1) I + b/2n _________ 2n In re/rw Where Q is the flow rate into spherical sinks located in the median plane of the sand laver Qo is the open hole flow rate (uncased hole of radius rw) b is the thickness of sand layer under consideration (always one foot in this paper) n is the number of spherical sinks in the sand layer rp is the radius of a spherical sink rw is the well radius re is the drainage radius of the well. Fig. 1 is a comparison of values calculated from equation (1) with Mus-kat's values. It will be observed that the approximate values are in error by less than 21/2 per cent. The disturbing effect of the casing on the flow line; is not explicitly taken into account by Muskat, but he reasons that interference between the flow pat- terns from the various point sinks will result in a negligible flow in the region within the well radius, and that no appreciable error will result from not explicitly excluding flow from this region. This line of reasoning is open to question, however, as the flow impedance, in the immediate vicinity of the well, of a hemispherical cavity in contact with an opening in the casing is twice that of a spherical sink in a continuous sand layer. There will be a difference, moveover, between the flow into a hemispherical cavity and that into a circular hole in the casing. .This latter difference can best be appreciated by comparing the flow from a semi-infinite medium into a hemispherical cavity at the edge of the medium with the flow out of a circular opening of the same radius as the hemisphere and which is also on the edge of the medium. In this case2 ------= —2, showing that the difference in flow rates into differently shaped cavities is quite appreciable. It was the purpose of the investigation reported here to determine to what extent flow into circular perforations in casing departs from the values calculated by Muskat. For this purpose an electrolytic model was used.

Jan 1, 1950

By George S. Rice

STUDIES of ground movement and subsidence caused by mining necessarily chiefly deal with causes and effects of making extensive excavations underground with spans beyond the strength of the un- supported or temporarily timbered roof or hanging wall. Perhaps no other phase of engineering is so de- pendent for results upon the assemblage of what may be called "experience data." That this is the case is cot surprising when one considers the number of variables involved in any at- tempted mathematical formula to determine the angle of draw or the angle of permanent slope of the rocks in any particular case. It is not like dealing with construction materials in which, through testing of. small specimens, in conjunction with the tests of large built- up specimens, relative stresses and strains may be deter- mined and formulas closely approximated for still larger constructions.

Jan 1, 1931

By J. Randel Hill

The 64th Texas Legislature passed the "Texas Surface Mining and Reclamation Act," Chapter 131, Texas Natural Resources Code (subsequently referred to as "the Act"), at a point in time when little surface mining had taken place within the state. Thus, enactment of regulatory control governing mining operations in our state has, for the most part, preceded widespread, intensive mining activity. I should point out that the statute applies only to the extraction of coal, lignite, uranium and uranium ore. A recent opinion rendered by the Attorney General's office has stated that extraction of the named elements, when it occurs incidental to the extraction of other materials, e.g., clay, is not not an activity subject to the Act. An important theme of the Act, frequently overlooked in other environmentally oriented legislation, is recognition of the Act's affect on the mining industry. The Act states that "the extraction of minerals by surface mining operations is a basic and essential activity making an important contribution to the economic well-being of the state and nation" and, in reference to reclamation being accomplished contemporaneously with mining, provides a recognition that "the extraction of minerals by responsible mining operations is an essential and beneficial economic activity." This legislative recognition is, of course balanced against the need for proper mined land reclamation, the rights of surface owners, the need to guard against unreasonable degradation to land and water resources and numerous other actions or events that the Legislature wanted protected. Another rather pervasive general theme that is established in the Act is the concept that the agency is entitled to obtain whatever information, or take whatever action, that appears reasonably necessary to effectuate the purposes of the Act. This concept, coupled with the detailed requirements placed on mining operations in the portions of the Act dealing with Permit Applications, Reclamation Plan and Reclamation Standards, easily insures that surface mining activities can and will be regulated to the extent necessary. Section 131.102(b)(2) is probably the most relevant provision in the Act which deals with the preclusion of mined lands becoming waste lands. This portion of the Act states that the surface mining operator shall: ". . . restore the land affected to the same or a substantially beneficial condition. ." In this language the Legislature had made it abundantly clear that the abandoned or orphaned lands found in some of the Eastern states, will not be tolerated in this State, and provided the Commission with a degree of latitude to determine what condition would be appropriate in each individual mining situation. I bring this area of the Act to your attention because it is the area which has received the most inquiries and concern by operators, i.e. what does "substantially beneficial" constitute? The Commission's staff has spent a considerable amount of time wrestling with the statutory language "substantially beneficial" to determine the legislative intent and provide operators with guidance of what they can expect. In this regard, the most definitive criteria in our opinion lies in the Act's legislative hsitory. The Legislature had before it basically three reclamation standards namely: House Bill 656, considered to provide the most stringent reclamation standard and identical to Senate Bill 66; House Bill 1717 which was supported by industry spokesmen and was considered to contain the least stringent reclamation standard; and Senate Bill 55 which was adopted by the Legislature. During the Bill's initial hearing before the House Environmental Affairs Committee, the House sponsor of the Senate Bill 55, which was the Bill eventually adopted, made the following statement: (I am quoting verbatim from the Committee's transcript although substituting the speaker's reference to the authors names with the Bill's numbers.) "An example of the differing approaches of the four bills can be seen in the area of reclamation standards and this is critical. House Bill 656, talking about restoring the surface of the land, House Bill 656 has this statement: 'At least fully capable of supporting the use to which it was capable of supporting prior to any mining or any higher or better use.' In other words you have to restore it to the level it was prior to the mining. Senate Bill 55: 'Restore the land to the same or substantially beneficial use.' Substantially beneficial use. (Emphasis his) House Bill 1717 says: 'Restore insofar as practical to appropriate beneficial post-mining use.' So that House Bill 1717 said to, 'restore insofar as practical to appropriate beneficial use. I think that's too weak, whereas I think the House Bill 656 that would call you to restore it to at least the use it had prior to the mining may also be too tight the other way. I think the Senate Bill 55 approach is down the middle of the road which says that you do restore it to the 'same or substantially beneficial use,' is a proper way to go there." Therefore, the conclusion that we have drawn from the legislative history of the bill is that the extent of reclamation required by "substantially beneficial" may be something other than the use it was prior to

Jan 1, 1979

THE annual meeting of the Lake Superior Mining Institute was held on Sept. 7 and 8, Crystal Falls and Iron Mountain, Mich., being the principal centers of activity. Members of both institutes began assembling early, and by the evening of Sept. 6, some 60 had already arrived at Crystal Falls. The greater number arrived the following morning, however, and after the usual formalities of registration were attended to, the party were loaded into automobiles and set out on a tour of inspection of the mines near Iron River; some properties were passed through, and some were briefly visited to permit the inspection of any unusually interesting piece of equipment or detail of practice. The last stop of the morning was at the Caspian, Iron River, where the entire party was entertained at luncheon at the Caspian Club House. Both the food and the company were excellent, and as the weather was superlatively good (though the natives of the district modestly declared it was only ordinary autumn weather) the lunch was served on the lawn at the rear of the club, where the green turf, abundant flowers, and music by the band, added to the charm of good fellowship. The degree to which mining men have become addicted to golf was indicated by the large number of plus fours in evidence, whose wearers appeared just before lunch and disappeared immediately afterward.

Jan 1, 1928

Discussion of the paper of GEORGE K. BURGESS and SIR ROBERT A. HADFIELD, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 455 to 468. ALBERT SAUVEUR, Cambridge, Mass.-There is a definiteness and finality in the investigations that have been conducted by the Bureau of Standards and in the method of presenting the results that is most satisfactory and refreshing.. A year ago Dr. Burgess and his co-workers investigated the question of critical points in carbonless iron, and they settled the question once for all. No one can now claim that the thermal point A2 in carbonless iron does not exist. At the past meeting of this Institute in Pittsburgh, Dr. Burgess showed the worthlessness of the shrinkage clause. To my mind after his demonstration no one can again claim that the shrinkage clause renders any service. He also showed us that it was a practicable proposition to use pyrometers in steel work in order to ascertain the finishing temperatures of rails. No one can again come before this body and make the claim that it is not a practical proposition. And now Dr. Burgess shows us that steel ingots can be made in a commercial way, practically free from pipe, from segregation, aid from blow holes. It places again before us in a very clear manner the question of piped ingots and of segregation, a question which has been debated for 20 years or more. I know very well the attitude of the standpatters in the matter. They claim that most of the pipe is removed in the discard, and that if a little is left it is so thoroughly welded that it does no harm. I for one am not convinced of the soundness of the argument. I do not believe there is any one present who would claim that, given an ingot free from pipe, free from segregation, and free from blow holes, better rails will not be made out of that ingot than out of the ordinary piped or segregated metal which is used by almost all of our steel mills. In my opinion, if we give our sanction to the casting of steel in the shape of piped or segregated steel ingots, we are guilty. If we give our sanction to the rolling of rails from such metal, we are guilty. It is our duty as experts, as steel makers, and as steel consumers to make and to use the best steel obtainable on a commercial basis, for the manufacture of rails. Now, we have been shown that sound ingots can be produced from which superior rails can be made. If we do not insist upon these sound ingots, then we fail in our duty. I think that the art of casting steel ingots has advanced to such a point that the casting of steel ingots piped and segregated ought no longer to be tolerated.

Jan 5, 1915

By R. V. Higgins

This paper presents a computer method to obtain the shape factors and equal cell volumes of the channels for any well spacing pattern from a potentiometric model. By using this program the authors have processed the data for the seven-spot, direct line-drive and the staggered line-drive patterns. The data for the five-spot pattern had been previously processed by a noncomputer method and are included for completeness. The shape factors and volumes for the channels are presented in tables for those who want to use them to process data using their own permeability relationships and viscosities of their reservoir oils. The authors have used the data and sets of representative permeability curves to process sample calculationr of waterflood performances. The comparison of the calculated results shows that the influence of well spacing is small. The permeabilities of the reservoir rock to oil and water had a greater influence on oil recovery for a given pore-volume throughput of water than the well spacing pattern. The more water-wet the reservoir rock, the better the possibility of permeabilities which are conducive to good recovery. The viscosity of the reservoir oil also influences the recovery more than the well spacing pattern. The reduction in the percentage recovery of oil with increase in viscosity of the reservoir oils is small when oil viscosities are in the range of 0.1 to 3. Above this range the reductions in recoveries are extensive. Sample comparisons of the time required for different patterns to recover the oil are presented. Results of an example calculation are given to show the effect of the permeability profile on recovery. INTRODUCTION The effect of well spacing pattern on the recovery of oil when flooding with either gas or water has been studied by many investigators. Muskat et al.1 presented an analysis using conductivity, sweep efficiency and unit mobility to the time of breakthrough. Dyes et al.2 used experimental techniques (X-ray shadowgraphs) and different mobility ratios. They presented quantitatively the relationship between mobility and sweep efficiency at and after breakthrough. Hauber3 presented a method to predict waterflood performance for arbitrary well spacing patterns and mobility ratios. Craig et al.,4 using techniques similar to Dyes et al. to determine sweep efficiency for a five-spot pattern, added the use of relative permeability curves at breakthrough and thereafter. Douglas et al.5 sed rela- tive permeabilities and continuously changing saturations throughout the entire five-spot flood pattern. In obtaining their solutions they used finite-difierence equations. Hig-gins and Leighton6,7 also used relative permeabilities and continuously changing saturations throughout the pattern before and after breakthrough. They employed techniques that process a flood-pattern calculation on the computer in about one minute. The methods of Douglas et al. and Higgins and Leighton both checked closely the laboratory results for a wide range of mobility ratios. This paper presents some sample performances calculated by the Higgins and Leighton method that show the effect on recovery of different permeabilities and viscosities using the seven-spot, the line-drive and the staggered line-drive, as well as the fivespot flood pattern. No previous paper has presented these data using different permeability curves and continuously changing saturations throughout the flood patterns. The paper also presents (1) the results and analyses of the flood-pattern prediction, (2) the computer techniques for determining the shape factors and volumes from the potentiometric models for the foregoing flood patterns, and (3) the shape factors and volumes of the channels of the flood pattern in the event reservoir engineers may like to process waterflood calculations using their own permeability curves and reservoir oils. DESCRIPTION OF METHOD VOLUMES AND SHAPE FACTORS The use of channels taken from a potentiometric model (see Fig. 1) to aid in calculating the performances of water floods of nonlinear patterns has been thoroughly explained in the literature.0,7 Therefore, very little theory, discussion, or proof regarding this phase will be repeated in this paper. The computer method presented in this paper to calculate the volumes and the shape factors of the channels of potentiometric models employs the trapezoidal rule for the volumes and the Pythagorean theorem (the hypotenuse equals the square root of the sum of the squares of the two sides of a right triangle) for the shape factors. In calculating the volume of a channel, the area of each cell in the channel is determined and then multiplied by the thickness to obtain the volume. In determining the areas of the cells, trapezoids are constructed whose vertical sides are spaced Ax apart, as shown in Fig. 2. The length of the sides is the difference between an ordinate cut off by the top and bottom of the cell — usually equipo-tentials. The coordinates of the points along an equipo-tential or streamline are obtained by Lagrange's8 equation of interpolation for which the constants are coordinate points at the intersections. Three intersections for con-

Jan 1, 1965

By A. T. Sweet, C. E. Plummer, H. W. St. Clair, S. F. Ravitz

The ammonium sulphate process for recovering alumina from clays was proposed by Rinman, Buchner, and others many years ago, and more recently various modifications have been investigated both here arid abroad.l-Is The process, as it is being investigated by the Bureau of Mines, involves the following essential steps: (I) sulphating the alumina in the clay by baking with ammonium sulphate at approximately 4m°C., (2) leaching with water to extract aluminum sulphate and ammonium sulphate, (3) crystallization of ammonium alum, (4) conversion of the alum to aluminum hydroxide by the ammonia gases given off during the baking, and (5) calcining the aluminum hydroxide to alumina. The over-all reaction between kaolinite (the most important alumina mineral in most clays) and ammonium sulphate during the baking step may be expressed as follows: Al2O8.2SiO2.2H2O + 4(NH4)2SO4 = (NH4)2SO4.A12(SO4)3 + 6NH3(g) + SH2O(g) + 2SiO2 [i] There is definite evidence. as is shown later. that the aluminum occurs in the baked product as anhydrous ammonium alum rather than as aluminum sulphate, provided the baking temperature is not much above 4o0°C. It is probable that the reaction takes place in the following steps: (NH4)2SO4 = NH3 -(- NH4HSO4 [2] Al2O3.2SiO2.2H2O + ;}NH4HSO4 = A12(SO4)3 + 3NH3 + 5H2O + 2SiO2 [3] A12(SO4)3 + (NH4)2SO4 = (NH4)2SO4.A12(SO4)3 [4] In onc modification of the process, the ammonium sulphate is first decomposed according to Eq. z, and the clay is treated with the resultant ammonium acid sulphate. Reaction I is highly endothermic. On the basis of the best available data, the following values have been estimated for the changes in heat content and free energy in calories per mol: -AH = 331,040 - 34T -AF = 331~040 - 78.3T log T - 671.8T The heat required' at 25OC is 320,900 cal. per mol, or 5650 B.t.u. per pound of alumina. The theoretical equilibcium pressure of NHa, based on the free-energy equation given above, increases very rapidly as the temperature rises above 3o0°C., and reaches one atmosphere at 43s°C. Ammonium alum solutions are almost ideal for crystallization. A saturated solution of ammonium alum contains 126. grams of AlzOa per 1000 grams of water at 90°C. and only 16.5 at 20 C. Hence most of the alum crystallizes out when the

Jan 1, 1944

By Robin O. Williams

The increase in internal energy as the result of deformation has been measured for lead, aluminum, silver, nickel, iron, and zirconium by using rapid, adiabatic compression. The stored energy increase is roughly Proportional to the strain; the propor-tionality constant increases rapidly with increasing melting point. The fraction of the mechanical energy which is stored increases more slowly, since the strength of the metals also increases with melting point. The values of the stored energy are considered accurate to about 10 pet. The present values appear about 50 pet larger than the more reliable published results where comparisons are possible. It is possible that this difference is due to the high strain rate used in this investigation. Immediately after deformation all these metals release energy at a rate roughly proportional to (time)-'. This release is considered to be associated with dislocation motion but in aluminum (and copper) some additional process seems to be present. This release can represent 20 pet or more of the stored energy. WHEN pure metals are plastically deformed, most of the mechanical energy is converted into heat. The energy remaining within the metal is significant in that it is the energy of the disorder produced and thus detailed knowledge of this energy is a powerful tool in understanding the nature of deformational disorder. While much effort has been expended on this problem, the amount of information available is limited. The situation as of 1958 has been carefully reviewed by Titchener and ever.' The present results have been obtained by a new experimental approach to this problem. The method necessitates high-strain rates which make comparisons with published results less certain, but a high-strain rate is an advantage in that the energy release immediately after deformation can be followed. EXPERIMENTAL PROCEDURE In the experimental method used, the internal (stored) energy is given as the difference between the mechanical work used in deforming the sample and the heat which is released (the first law of thermodynamics). The work is supplied by two identical hammers swinging freely from a fixed height, the available energy being the product of the mass, the gravitational constant, and the distance through which the center of gravity moves. The initial temperature rise of the sample represents the heat produced by the deformation. The sample temperature is determined by a small thermocouple embedded in and supporting the sample. This process can be repeated over and over to produce increased strains. Most samples are run through about five cycles to a total strain of around 0.7. Further details are covered elsewhere. The determination of the heat is dependent upon the sample weight, its specific heat, the rise in temperature, and any gains or losses to the surroundings. One is dependent on published results for specific heals (the values were taken from a collection).3 The values must be accurate to about 0.1 pet in order that they not affect the results. The best values thus do not contribute to the uncertainty, but this is probably not always the case. The accuracy of the temperature rise is limited primarily by knowledge of the thermocouple characteristics over short temperature intervals, but careful calibration eliminates this as an important factor. One can calculate readily the heat flow between the sample and hammers if the time of contact and the sample temperature are known and if there were no oil at the interface. Assuming the maximum temperature difference, upper values for this interchange have been calculated (the time of contact is determined from the decrease in sample length) and it may or may not be significant. However, no correction is colnsidered necessary because of the presence of a thin oil film which has a thermal conductivity much less than the metals. Except for the possible uncertainty in specific heat, the heat is considered to be adequately known. The mechitnical losses which are recognized as important are: 1) friction between the sample and the hammer:;, 2) the kinetic energy in the hammer suspension system which may not be entirely usable, 3) the rebound energy of the hammers, and 4) the vibration of the hammer heads. All these have been covered in detail elsewhere2 and only the more significant points are made here. The friction turns out to be small except for soft materials (lead)

Jan 1, 1962

By LESTER H. WOOLSEY

IT IS doubtful whether anything new can be said upon this subject and, therefore, it is with considerable hesitation that l prepare this paper. On account of my recent connection with the Department of State as its law- officer, perhaps I will be pardoned if I discuss this subject briefly from the point of view of that branch of the Government. , I cannot, of course, speak for that department, since I have-no connection with it at-present, but it may be helpful if I set down certain* of the factors which in my opinion and from my experience have a bearing on this international problem. With oil-burning ships, motor vessels, motor vehicles, airplanes-all consuming, astonishing quantities of petroleum or petroleum products; with the United States having within its borders only 12 per cent. of the petroleum resources of the world, and consuming about 70 per cent. of the world's output; with the more enterprising nations wide awake to the necessity ; of obtaining and preserving as large a share as possible of the oil resources extant ; the 'problem is peculiarly and in a, very practical sense an international one.

Jan 1, 1921

By J. A. Coll, R. W. Cahn, A. Lawley

WHILE the creep properties of pure face-centered-cubic and close-packed-hexagonal metals have been thoroughly investigated and are well established, body-centered-cubic metals have been studied less extensively. Moreover, very few fundamental studies on the creep of solid solutions, irrespective of crystal structure, have been reported. The present study is concerned with the creep of a series of body-centered-cubic solid solutions. The present position concerning creep of pure metals is, briefly, as follows.1"3 Creep at first takes place at a steadily decreasing rate; this is the stage termed primary or transient creep. Except at the lowest temperatures this is succeeded by a stage of secondary or steady-state creep. At high temperatures and stresses, this may be succeeded by an accelerating stage, termed tertiary creep, with which we shall not here be concerned. There is no well-defined physical model at present for the transient stage; in general terms, transient creep is best regarded simply as a manifestation of work-harden ing. Steady-stage creep can certainly take place by several different mechanisms: the choice of dominant mechanism depends primarily on temperature. We shall here be concerned only with high-temperature steady-state creep, a term usually reserved for creep at absolute temperatures higher than 0.5 Tm, where T, is the melting point. In this range, the activation energy for creep is, for many metals, equal to the activation energy for self-diffusion, and this is generally interpreted in terms of a "climb mechanism.1-4 The creep rate is determined by the speed at which dislocations, impeded by obstacles the nature of which is disputed but which are probably established during transient creep, can climb by means of a diffusion process, until they are able to by-pass the obstacle. In solid solutions, the intrinsic resistance to the slip motion of dislocations may be much larger than in the solvent, to the extent that the motion of dislocations in the glide plane, rather than their escape by climb out of this plane, may become the rate-controlling factor. weertman5 has considered this possibility from a theoretical point of view, and concluded that some form of "viscous slip" is likely to be rate-controlling at comparatively low stresses. The resistance to slip may arise from "atmospheres" of impurities forming around dislocations; a high Peierls force in materials of high cohesion; or some structural peculiarity such as clustering or ordering of solute atoms.= We shall be concerned here with the case of ordering. The only published investigations concerned explicitly with the effect of order on creep refer to creep in ß-brass by Herman and Brown,7 and in Ni-Fe alloys, by Kornilov and panasyuk8 and by Suzuki and Yamamoto.9 Recently, Herman and Brown's paper has been supplemented by a determination of the tensile yield point of ß-brass as a function of temperature.10 Both studies showed a sharp drop in resistance to deformation of ß-brass over a range of a few degrees just above the critical temperature Tc at which order finally disappears. These observations are especially noteworthy, because in ß brass the degree of order diminishes steadzly to zero as the temperature approaches Tc. It is, therefore, the disappearance of the last traces of long-range order which has the largest effect on the resistance of the alloy to plastic deformation. In the Ni/Fe alloys of various compositions, resistance to creep at a given temperature and stress is maximum at the stoichiometric composition, both below Tc, (long-range order), and above T,. (short-range order).' Near Tc, the creep resistance of an ordered alloy is much higher than that of the same alloy in the disordered condition.9 The aim of the present investigation was to study the creep behavior in the neighborhood of Tc, of another system of ordering alloys. The iron-aluminum alloys were considered the most suitable. because: i) The order again diminishes steadily to zero as the temperature approaches Tc; there is no sudden drop in order at Tc, and it therefore is

Jan 1, 1961

ONE of the features of the annual meeting was a round table conference on carbon in pig iron, on Feb. 16. This was presided over by R. H. Sweetser, and the discussion, which was so interesting as to require holding an additional session in the after-noon, ranged over such a wide field that only a brief outline of it will be attempted here. The full discus-sion together with the papers will be printed later. The first paper was one on the need for research in foundry pig iron (1648-C) by Richard Moldenke, who pointed out the trend in present practice of attaining low cost in pig iron production by hotter blast, addi-tion of. scrap to the blast furnace, and. the enormous increase in the output per furnace day. He pointed out that remelting processes are oxidizing processes, to some degree at least, and the metal cannot be given the deoxidizing finish which is characteristic of the steel-making process. The trend today is toward specifying total carbon content in foundry pig irons, and since the carbon content depends on a variety of factors, he suggested that the blast-furnace men and the foundry men study the question and agree on a minimum of total carbon for the given silicon ranges. The discussion of this paper was participated in by E. J. Lowry, Robert Jones, T. L. Joseph,. R. H. Sweet-ser, J. G. Ferguson, W. B. Coleman, E. P. Ross and D. J. Demorest and ranged from a comparison of the total carbon used in making a ton of pig iron in charcoal practice versus coke practice to a discussion of the bad effects observable from the use of scrap This paper was followed by one on carbon character-istics of copper-bearing pig iron by W.. B. Coleman. In view of the belief in many foundries that copper-bear-ing pig iron made trouble in the foundry, experiments were made by adding copper in various amounts up to 1 per cent and with the cooperation of the Robesonia Iron Co. a large number of tests were made over a run of foundry iron. The final conclusion was that the ad-dition of less than 1 per cent metallic copper did not seem to alter the physical properties and that a blast furnace using copper-bearing ore can produce pig iron suitable for making small castings, showing low-Brinell hardness test, good transverse and deflection tests, and high-total carbon.

Jan 3, 1927

By Paul Queneau

FEW of us who waded ashore on the Norman beaches realized the importance of coal to a successful invasion. General Eisenhower and his staff had been aware of the essential need for coal and an able Solid Fuels Section had been set up under the direction of Colonel Robert P. Koenig, of Indiana. This organization met the requirements of the invading armies on their march to the Rhine. East of the Siegfried Line enemy territory, the Army Engineers were called upon for assistance. When the Engineers were advised that, in addition to their normal duties, they were to occupy and place in operation the coal mines in the Twelfth Army group area, plans were drawn up overnight and action was initiated immediately. The Sixth Engineer Special Brigade, a versatile outfit which made a notable record D-Day on Omaha Beach, was selected to handle the operation. Within 48 hours of the new assignment an advance command post was set up cm the west bank of the Rhine at Homberg, just below German-held Duisburg. The 368th Engineer General Service Regiment was assigned to the Brigade, and the British 44th Pioneer Group, including specialist personnel, was also attached. This large British unit was added because most of the mines would shortly come within the British zone of

Jan 1, 1946

By J. C. Kerkering, P. M. Daling

This paper discusses a study performed to evaluate the feasibility of transferring formal system safety assessment technology to the mining industry. A representative listing of formal techniques was evaluated to select the most useful methods for the mining industry to implement. Criteria for selecting methods included the interests, needs, and requirements of mine safety officials. This paper describes one of the selected methods, preliminary hazards analysis (PHA), and illustrates the analysis procedure for a mining example. This study also includes an assessment of the adaptability of selected methods to a user-interactive computer system for use by mine safety personnel. This paper includes a description of a conceptual computerized PHA-type safety program that facilitates performance of the safety analysis and can accommodate updates and revisions as necessary.

Jan 1, 1983

By G. B. Thomas

Several methods of analyzing pressure build-up data in wells have been presented by various authors. This paper reviews the theory and method of D. R. Horner and presents example calculations performed on data obtained by testing several different types of wells. These calculations include, (1) graphical estimation of final static pressure, (2) determination of the productive capacity of the pay away from the well bore and. (3) the degree to which the formation adjacent to the well bore has been damaged by completion or other causes. The methods of testing and precautions which should be taken to assure the best data possible are discussed. Limitations and reliability of calculated results are also treated. INTRODUCTION Pressure testing of wells is generally limited to the determination of producing and static mean formation pressures. The so-called "static" pressure determination.. along with PVT, electric log and production data, enable the reservoir engineer to determine, within reasonable limits, the drive mechanism of the reservoir and in some cases. the amount of edge water encroachment. Producing pressure tests enable calculation of productivity indices and allow the engineer to plan the systematic production of a pool for optimum conservation of suhsurface energy. The radial flow formula advanced by Muskat' has been based on the assumption of incompressible radial fluid flow. It has been known that reservoir fluids do not behave in an ideally incompressible manner. For example, incompressible flow theory indicates a simple logarithmic relationship between the difference of the instantaneous and static well pressures when plotted against time. 'The latter stages of this type of plot of pressure build-up data generally show a marked devia-, tion from the earlier straight line trend. which deviation may be shown to be due to the compressible flow of fluids toward the well bore. Shut-in times of 24, 48. 72. or at most 96 hours are currently in wide use for determining so-called "static" reservoir pressure. Due to the continuation of compressible flow of fluids into the well bore long after this arbitrarily taken shut-in time, the determination of static pressures has almost invariably resulted in lower than equilibrium values. Materials balance calculations made early in the life of a reservoir often result in a calculated reserve which later observations prove to be too low. Failure to obtain reliable "static" reservoir pressures within the prescribed 24 or 48-hour build-up period has undoubtedly been a major factor in obtaining these low estimates. Comparison of theoretical and actual productivity performance has indicated that formation damage and not being able to attain true static pressures have been partially responsible for the observed discrepancies. Research into the theory of compressible flow behavior has resulted in methods of applying these theories to the testing of wells. Application of the developed theories to pressure build-up performance indicates that in many cases the following can be estimated. 1. The static reservoir pressure. 2. The in-place effective formation permeability away from the well bore. 3. The degree or extent by which the formation has been damaged adjacent to the well bore, either through completion methods or subsequent damage due to fluid entry. REVIEW OF THEORY Horner2 has shown that the pressure build-up within a "point source" well is approximated by the following formula: Equation (1) is the approximate "point source" solution to the radial compressible flow equation advanced by Muskat. The solution assumes the following: 1. A point source well is producing at constant rate from the center of an infinite reservoir with a constant pressure at its external boundary. 2. The fluid flowing is present in one phase only. 3. The compressibility and absolute viscosity of the fluid remain essentially constant over the range of temperature and pressure variation encountered. 4. The well i.; shut-in at the sand face arid there is 110 after production into the well bore. 5. The formation permeability is homogeneous in the direction of flow. From Equation (1) it can be seen that if an ideal well were shut-in while producing from a reservoir under the conditions assumed, the pressure build-up would be a logarithmic func-

Jan 1, 1953

By HAROLD VINTON COES

MANAGEMENT has been tersely defined as getting things done through the efforts of other people; but before we proceed further, let us distinguish between administration, management, and organization. Oliver Sheldon in his book, "The Philosophy of Management," offers the following definitions: Administration is the function in industry concerned in the determination of the corporate policy, the co-ordination of finance, production, and distribution, the settlement of the compass of the organization, and the ultimate control of the executive.

Jan 1, 1943

By Albert A. Mathews

OUTCROPS of gypsum rock near the present site of the city of Gland Rapids, Mich., were known to fur traders early in the nineteenth century. However, the deposits seemed without value and were not worked for some time. So far as cat1 be learned, Michigan gyp- sum was first used by a plasterer who settled in Grand Rapids in 1834 as a member of its fourteenth white family. In building a house for one of the early traders, be used some otnamental stucco mouldings manufactured from the local gypsum deposits for decorations in the gables and around some circular windows. The gypsum was broken out with a hammer, ground in an Indian corn mill, and burlled in a caulclron kettle,. After two attempts, the ornaments were successfully set, and remained on the house until it was destroyed by fire in 1850.

Jan 1, 1936

By K. C. Sclater

GAS as a factor in the efficiency of oil production, might be a better title for this paper as it deals in general with the significance of the gas-oil ratio as an index of the efficiency of oil production and briefly discusses oil production methods with reference to the gas-oil ratio in wells, particularly during the early life of a field. In the recent hearings held at Washington before the Federal Oil Conservation Board the fuller utilization of the energy contained in the gas occluded in or associated with the oil underground was stressed by some of the speakers when referring to greater ultimate recovery of oil. One speaker commenting on this point said in part, "There is ample evidence indicative that if the gas associated with the petroleum in our fields were conserved and elevated gas pressure maintained in the oil sands during their productive life, the ultimate production of oil could be greatly increased."

Jan 1, 1926

By F. Selig, A. S. Odeh

A second-order approximation to the exact solution of the diffusivity equation corresponding to the pressure build-up of a well producing at a variable rate is derived. This approximation is applicable when the well's shut-in time is larger than the total time elapsed since the well was first produced. The resulting equations are compact in form and easy to use. Thus, the need for Horner's' theoretically precise but rather laborious solution to the above problem is eliminated. In addition, these equations apply where the use of Horner's widely known approximate method is questionable. From a practical point of view, the reported method is best suited for analysis of drill-stem tests and short production tests conducted on new wells. INTRODUCTION The utility of drill-stem and short production tests in reservoir studies has long been recognized by the reservoir engineer. If interpreted correctly they could lead to a wealth of information upon which may depend the success or failure of reservoirs' analyses. Initial reservoir pressure and the average flow capacity are two quantities that are normally sought from a drill-stem and/or a short production test analysis. Pressures are the most valuable and useful data in reservoir engineering. Directly or indirectly, they enter into all phases of reservoir engineering calculations. Therefore, their accurate determination is of utmost importance. The flow capacity kh of the reservoir is indicative of its commercial capability. In addition, it can indicate the presence of a darnaged zone around the wellbore and, thus, the necessity for remedial measures. Of the several methods used to analyze drill-stem and short production tests, Horner's' method is by and large the most common. It applies to an infinite reservoir and or a limited reservoir where the effect of production has not been felt by the boundary. Horner's method makes use of the so-called "point-source" solution of the diffusivity equation. The point-source solution is approximated by a logarithmic function and the superposition theorem is utilized to give the familiar pressure build-up equation where is the shut-in time, q is in reservoir barrels per day and the rest of the symbols conform with AIME nomenclature. Eq. 1 was derived for a well which produced at a constant rate q from time zero to time t and was then shut in. In actuality, such a constant rate of production does not normally obtain. Therefore, a correction must be applied to Eq. 1 to account for the varying rates of production. Horner suggested two methods. The first, which results in a theoretically accurate solution, is rather lengthy and laborious and, thus, it is not suited for routine analysis. The second which has been termed a "good working approximation" is the one used by the majority of the reservoir engineers. In the second method, Eq. 1 is modified by simply introducing a corrected time t, and writing where q is the last established production rate prior to shut-in, and t, is obtained by dividing the total cumulative production by the last established rate. Horner's original paper does not give any indication that this method of correction is based on any theoretical justification. In addition, there is a question as to what constitutes the last established rate. In case of a drill-stem test some engineers use the average rate obtained by dividing the total fluid produced by the total flow time, while others calculate the average rate by dividing the total fluid produced by the last flow-period time. Obviously, different results obtain for the different flow rates used. Because of this, a simple method to the varying-rate case was developed which is theoretically sound and which defines clearly the flow rate and its associated time to be used in the calculations. The final equation arrived at is where q* and t* are a modified rate and time, respectively, and can be easily calculated. In addition, it is shown theoretically that Horner's approximate method, if used for a variable-rate case, gives the correct pressure but would not be expected to give the correct flow capacity. MATHEMATICAL ANALYSIS The general equation governing the flow of slightly compressible fluid in porous media may be written as The elementary solution to Eq. 4, representing an instantaneous withdrawal of Q units volume of fluid at the origin at t = 0, is known as the instantaneous sink

By Hiland G. Batcheller

HISTORY shows that the nation which makes the most steel is the most likely to win wars. Today the course of war shows that the nations which get there first with the most steel of the right kind will be the ones to win. Not only the most steel, mind you, but the right kind. Adequate production, which was enough for victory before the days of totally mechanized warfare of 1943, must now be accompanied by still better quality as well as more effective distribution. Further, both production and distribution must be flexible enough to permit rapid shifts from one weapon to another for use in varying elements in varying geographical areas. Thus the problem of making enough steel of the right kind at the right time in the face of changing requirements dictated by experience has been and will remain highly complex. This does riot permit us to ease our restrictions on nonessential use. War is a complex business, like the job of making steel for war. Each time we solve one problem, another pops its head up. Yet we are making some progress.

Jan 1, 1943

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946