Search Documents

By Wei Yu, Tiejun Chun, Jian Pan, Deqing Zhu

In this paper, improving the pelletization of Brazilian hematite by adding a boron bearing additive was carried out, and the pelletization parameters were also optimized. The mechanism of boron bearing additive was revealed in the kinetics of crystal grain growth by using LEICA microscopy and its software to measure hematite grain growth. Good qualities of green balls are manufactured with drop numbers above 5.7 times/0.5m, compressive strength higher than 13 N/pellet and thermal shock temperature over 620? under the following conditions: 1.2wt% bentonite, 0.4wt% boron bearing additive, 7wt% moisture and pelletizing in disc for 15 min. When the green balls were preheated at 1000? for 8 min and fired at 1280? for 15 min, the compressive strength of the fired pellets containing boron bearing additive is about 3096 N/pellet, which is far beyond the standard requirement for good quality pellets. Compared to the fired pellets without adding any boron bearing additives, the compressive strength of fired pellets containing boron bearing additive is increased by 1225 N/pellet. It is revealed that adding boron additive into the hematite pellets help to form more liquid phases, lower the activation energy of the hematite grain growth by 135.2 kJ/mol and increase grain growth rate by 33.6%, leading to higher strength of fired pellets due to forming more coarse and dense recrystallized hematite and energy saving by firing at lower temperatures for shorten time.

Jan 1, 2011

By M. Z. Sukiennik

A static method for vapor pressure measurement up to 1450 K and above 1 hPa is presented. The method is designed for equilibrium and kinetic studies of metallic systems, including those with a chemical reaction. Application examples are given for determination of activities in condensed phases, and heterogeneous reaction rates and equilibrium constants.

Jan 1, 1993

By K. Yamaguchi, Y. Takeda

"Partial pressure - temperature - composition correlation diagrams of the Ga-As, In-As, Ga-P and In-P systems were contracted based on the obtained experimental data of the phase diagram and thermodynamic properties for the III-V systems. The total vapor pressures of arsenic or phosphorus at melting point of GaAs, InAs, GaP and InP were determined as 101, 10.1, 1510 and 253 kPa, respectively, at the corresponding melting points of 1509, 1211, 1739 and. 1336K , These diagrams are applied to the analysis of the horizontal Bridgman method and the liquid phase epitaxial growth technique. On the other hand, the analysis of the equilibrium state of the. chloride-CVD process was carried out using the data of the Gibbs energy of the compounds obtained by· authors.IntroductionThe group III-V compound semiconductors ate important materials used in optoelectronic liquid high speed electronic device. The crystal growth of the III-V compounds can involve processes that require contact between the solid, liquid and vapour phases at near equilibrium condition. Examples of processes that involve contact between the solid, liquid and vapour phases include bulk crystal growth such as the horizontal Bridgman and the liquid encapsulated Czochralski method and liquid epitaxy, and between the solid and vapor include chemical vapour deposition and molecular beam epitaxy. Therefore, the knowledge of the phase diagram and thermodynamic properties for the III-V binary alloys is essential for the analyses of crystal growth techniques of III-V compounds.For these reasons, a series of different · types calorimetric measurements had been carried out: (1) The heat contents of alloys for the Ga-As, In-As, Ga-P and In-P systems by a drop calorimeter [1;2,3]; (2) the heats of formation of the GaAs, InAs, GaP and InP compounds by a twin solution calorimeter [4]; and (3) the standard entropy of these compounds by an adiabatic calorimeter [5]. Based on the third law method, the Gibbs energies of these compounds were derived from the heat capacity, standard heat of formation and standard entropy data obtained by authors. Integral molar thermodynamic quantities of the liquid III-V .alloys were also determined from combining the heat contents of alloys with standard heat of formation and standard entropy data of the compounds· by applying the thermodynamic analysis method developed by Oelsen [6]. In the present study, the thermodynamic calculations for the crystal growth processes of the III-V compound were carried out using newly experimental data of the phase diagram and thermodynamic .properties measured by authors"

Jan 1, 2000

By Y. Y. Liu, H. M. Domanus, W. T. Sha

"Casting is fundamental to manufacturing of many types of equipment and products. Although casting is a very old technology that has been in existence for hundreds of years, it remains a highly empirical technology, and production of new castings requires an expensive and time-consuming trial-and-error approach.In recent years, mathematical modeling of casting has received increasing attention; however, a majority of the modeling work has been in the area of heat transfer and solidification. Very little work has been done in modeling fluid flow of the liquid melt. This paper presents a model of fluid flow coupled with heat transfer of a liquid melt for casting processes. The model to be described in this paper is an extension of the COMMIX code and is capable of handling castings with any shape, size, and material. A feature of this model is the ability to track the liquid/gas interface and liquid/solid interface. The flow of liquid melt through the sprue and runners and into the mold cavity is calculated as well as three-dimensional temperature and velocity distributions of the liquid melt throughout the casting process.IntroductionBower et al. (1), in their 1969 review of the evolution of some of the casting techniques, stated that:""The evolution of technology requires alternatives to be available so that choices can be made that lead to changes. The role of solidification science and other disciplines related to casting technology is to develop a better understanding of process and product, so that a wider range of alternatives is possible.Alternatives, whether from science or from invention, must lead to improvements in casting ""utility."" Utility, or economic advantage, must include consideration of total system costs, and final product value. The cost of materials, melt processing and finishing should be optimized with casting costs, since all are part of the production system. It is the favorable relationship between total processing costs and product value that makes a change in casting technology viable, but the best change is not possible unless technology has provided an understanding."""

Jan 1, 1986

By M. Ide, K. Takemura, S. Taenaka, K. Shinzawa

"The laser characteristic is strongry dependent upon the stoichometry of forsterite (Mg2Si04) and YSO (Y2Si05) single crystals, because of change in the valency and occupied sites of doped Cr in the lattice so that mole ratios of Mg0/Si02 and Y203/Si02 in the above single crystals must be precisely analyzed. In this study ICP-AES was applied for analyzing the mole ratios. Emission intensities corresponding to Si and Mg or Si and Y were measured at the same time with internal standard method. Preparation of sample solutions, measurement conditions of ICP-AES and interferences by coexisting components were discussed, resulting in excellently precise detennination of stoichometry of the above single crystals.IntroductionIn conventional stoichiometric analysis of single crystals, the stoichiometry is detennined by analyzing each component separately with titrimetry and gravimetry techniques. On the other hand, by stoichiometric analyses using ICP-AES, emission intensities corresponding to components are measured at the same time with internal standard method. Consequently erros caused by variation of analytical condition are canceled out.Cr-doped Mg2Si04 and Y2Si05 syngle crystals are known as laser materials. The change of valency and occupied sites of doped Cr affect the characteristic of single crystal as aleser materials. The change of state of doped Cr.Stoichometric composition of Mg2Si04 is constructed by 2mole of MgO and 1mole of Si02, and Y2Si05 is constructed by 1mole of Y203 and 1mole of Si02. In this study, required analytical precision in component mole ratio is within an error of 0.0010 for Mg2Si04 (CV=0.05wt%), and within an error of 0.0030 for Y2Si05 (CV=0.05wt%) (Table I )."

Jan 1, 1998

By Jintao Gao, Zhancheng Guo, Chong Li

A new approach to enrich MFe and RO phase from the converter slag by super gravity was investigated. The samples obtained by the gravity coefficient G=600 and cooling rate V=5K/min from 1623K to 1373K appeared significant stratification and the MFe gathered at the bottom of sample. With the help of metallographic microscopy and X-ray diffraction, it is found that large quantity of white RO phase gathered at the lower part of the sample as the concentrate, with volume fraction appearing gradient distribution along the direction of super gravity, while the upper part was mainly composed of dicalcium silicate as the tailing. The mass fractions of the FeO, MgO and MnO in the concentrate are up to 40.46%, 6.9% and 3.91%, while that in the tailing are just 11.65%, 2.15% and 1.55%. The recovery ratios of FeO, MgO and MnO in the concentrate are 60.35%, 58.45% and 72.24%, respectively.

Jan 1, 2016

By Shengli Wu, Juan Zhu, Wei Huang, Xinliang Liu, Kaiping Du, Kaifa Zhang

Based on the furnace burden of high content of Al2O3, the process of softening and melting and the characteristic of primary slag were studied with the increase of MgO content in the sinter and adding some MgO into the pellet. The results showed that the content of MgO in the primary slag increased with the increase of MgO in the sinter and pellet. Meanwhile, the permeability of the furnace burden was improved because of low viscosity of high MgO primary slag. Compared with the increase of MgO content in the sinter, the increase of MgO content in the pellet can improved the softening and melting characteristic of the comprehensive furnace burden more effectively. More Mg-bearing pellet should be chosen in the comprehensive furnace burden for the purpose of improvement the fluidity of primary slag and the permeability of the furnace burden in the burden of high Al2O3 content.

Jan 1, 2015

By Guo Chang Jiang

In order to improve the IIAZ toughness of X-60 pipe steel, the intragranular ferrite plate (IFP) technology was used. The characteristics of IFP is claimed to be much fine ferrite plates appear inside the original austenite grains. By means of suitable Re, Zr, Ti additions in a bath with a higher initial oxygen potential, a good control of the peak temperature and the cooling rate during welding simulation, one can get a %IFP in volume over 50%, and the toughness gets up from 55 J to 160 J. It was found that the inclusions most effective in nucleating IFP are some deformable complex silicates which either entrap Re, Zr, Ti oxides or contain these elements. The greater the number of the evenly distributed and effectively nucleating inclusions, the more the %IFP in volume, and the finer the microstructure of the HAZ, so the better the relevant toughness. Generally, these silicates bahave as fine spheres along a line. The present authors revealed that these fine spheres result from the remelting of the shuttle- like silicates due to heating in the process of welding simulation. These silicates used to get a higher sulphur capacity, so MnS deposits might be observed on the periphery of the silicates. IFP was proved to be directly rooted in the [Mn] depleting zone which locates beside MnS deposits.

Jan 1, 1997

By K. Krishnapisharody, G. A. Irons

"The modeling of gas-liquid plumes in steelmaking ladles has been the subject of many investigations. In most studies, the “modified” Froude number, based on the momentum of the injected gas, has been employed to characterize two-phase plumes. This approach has several shortcomings and is critically reviewed in the present work. Based on an extensive review of previous work and theoretical considerations, it is demonstrated that the injected momentum and consequently, the modified Froude number has no significance to gas blowing operations in Ladle Metallurgy. Instead, an approach based on the “plume” Froude number, previously shown by the authors as the proper form for Froude similarity, is extended as a simpler alternative.IntroductionGas injection is central to most Ladle Metallurgy operations. During ladle processing, the steel melt is usually stirred by an inert gas like Argon through porous plug(s) fitted in the bottom of the ladle or a lance inserted deep into the melt. The purging serves several purposes viz., homogenizing the melt, flotation of inclusions, enhancing the rates both of refining reactions and dissolution of alloying elements and promoting inter-phase interactions in the ladle.The topic of gas injection into liquid baths has been the subject of several investigations in the past. A great deal of this work, both experimental and computational, was devoted to describing the structure and properties of two-phase plumes as reviewed recently [1]. Generally, the ascending two-phase mixture is sub-divided into three distinct regions [2]: the jet core, transition and the bubble plume, respectively. The jet region, where the momentum of the injected gas is transferred to the bulk liquid, is also called the ‘momentum region’. In a similar manner, the plume is called the ‘buoyancy region’ where the motion of liquid is caused by the buoyancy force exerted by the bubbles. The proper characterization of these regions is important for the analysis and modeling of stirring operations in Ladle Metallurgy. Although many mathematical correlations exist for this purpose, some issues of theoretical and practical interest to the modeling of gas-liquid plumes need further attention."

Jan 1, 2012

By Onuralp Yucel, Ahmet Turan, Murat Alkan, Hasan Ozer

SHS (Self-propagating High-temperature Synthesis) is one of the important methods to synthesize B4C powders. The process contains the reaction of boron oxide powders (B2O3) with magnesium reducing agent and carbon black carburizer. SHS products are leached in HCl media to purify synthesized B4C powders in the following step. In the present study, effects of various functional additives (KClO3, KHSO4, MgSO4.7H2O, NaCl, MgO and Na2SO4) in the SHS stage were carried out. Various proportions of the additives were mixed with the initial SHS charge mixtures. Two different molar ratios were employed in the initial SHS mixtures as 1:3:0.8 B2O3:Mg:C and 1:2.5:0.8 B2O3:Mg:C. After the SHS step, HCl leaching process was applied to the SHS products. Filter cakes were dried and characterized by using X-Ray Diffraction Spectroscopy, BET and chemical analysis techniques.

Jan 1, 2015

By Jiang Fan, Liu Shi, Wang Haigang

Winter-time natural convection in gravel embankments has been suggested as a technique to provide passive cooling and thereby avoid thaw-settlement of roadways located in permafrost areas. Numerical simulation by finite volume method on the proposed model is perf9rmed using the software FLUENT. A gravels model, in which the embankment is composed of stones and air, has been adopted to investigate the temperature and velocity fields in embankment. Simulation results show that in summer, a weak clockwise circulation of the pore air extending throughout most of the embankment. The pore-air motion is very weak which results in relatively straight horizontal isotherm lines. And heat transfer is mainly maintained through conduction. But in winter, pore-air velocities are higher and multiple vortexes are formed in the embankment. Natural convection then becomes the dominant influence on the isotherm shapes within the embankment. As a result of low ambient temperatures exerted on the embankment surface during winter months, an unstable air density gradient develops within the embankment. This convection increases the heat flux out of the embankment. Therefore, the winter-time convection can further reduce the temperature of the foundation soil beneath the open-graded embankment. In addition, the effects of the size of the stones within the embankment have been analyzed and compared in the gravel model. It shows that in winter, 200mm stones lead to stronger vortexes in the embankment compared with those of 60mm stones. Consequently, the zone oflow-temperature beneath the embankment is extended.

Jan 1, 2004

By Sheng Dai, Yuan Lee, Haiming Xiao, J. P. Young

"There are numerous analytical applications of scatter-emission and/or absorption spectroscopy applied to liquids and solids in the temperature range of 0 to 350°C. In this paper an all-silica fiberoptic probe is described which is useful for spectral analyses from 0 to 1600 K and can be used in harsh chemical environments. The probe has been used for Raman spectral analyses of many molten salt and solid material systems to 1000°C. It has applications for such studies at higher temperature ranges. The instrumentation required along with the demonstrated and proposed applications of the all-silica probe are presented and discussed.IntroductionThere are many kinds of scatter-emission spectroscopies that are of value for analytical measurements. Fluorescence, reflectance, arc or spark emission are descriptors for some of these. Raman scatter spectroscopy is also quite a useful technique for analytical measurements.In Figure 1, we give a simplified explanation of the Raman effect. If one shines monochromatic light into a sample, light may be absorbed, exciting the sample to some virtual state. We know from experience that almost all of the light is re-emitted in the same wavelength range. This is called Rayleigh or Mei scattering and is designated in the figure by the arrows in both examples that point up and down from the same lower energy state. A very small percentage (the order of 10-4%) of the monochromatic light is re-emitted leaving the sample at a vibrationally-excited state. Thus, this light is at a distinctly lower energy compared to the exciting radiation. This is called a Stokes shift and is represented in the left-hand example by an arrow descending to a more energetic vibrational state. If the sample is not at a temperature of absolute zero, some of this vibrationally excited state will be thermally populated. That portion of the sample still absorbs and re-emits exciting radiation as Rayleigh scattered light, but a small percentage of the exciting light is re-emitted as the sample relaxes to the lower vibrational state. The energy of this light is of higher energy and is called an anti-Stokes shift, depicted in the example to the right. Notice that the energy separation of the Stokes or anti-Stokes shifted emission from that of the exciting radiation is the same, and expressed in ~cm-I. The intensity of either shifted emission is a function of the population of the vibrational energy states; therefore, the ratio of the intensity of Stokes to anti-Stokes signal varies with absolute temperature. We will come back to this point later."

Jan 1, 1997

By XING Xiangdong, Zhang Jianliang, MA Jinfang, WANG Zhenyang

The non-equilibrium reflux reaction behavior of phosphorus was studied with synthetic slags formed by using the AR chemical reagents and changing the initial condition of basicity, FeO, MgO and Al2O3. Due to increase of viscosity, the dephosphorization slag with high basicity inhibits the full contact of slag with iron, which leads to the low reaction rate in the early stage. However, since the high basicity improves the activity coefficient of CaO, the dephosphorization rate and phosphorus capacity goes up in late reaction stage. FeO promotes the increase of reaction rate in early dephosphorization stage. But the polarization force of Fe2+ is stronger than Ca2+, which hinders the reaction between phosphate ion and CaO and reduces the stability of PO4 3-. Thus, high content of FeO will adversely impact on dephosphorization reaction. In addition, MgO has a promoting effect to the dephosphorization, whereas Al2O3 has a negative influence.

Jan 1, 2016

By P. F. Stratton, M Huggahalli, N Saxena

"Several studies have been carried out to determine how the optimum atmosphere conditions in the heat treatment of metals can be established for a given product by using different gas injectors and varying atmosphere flow rate and composition. The most common approach taken to gain insight into furnace atmospheres has been to use commercial computational fluid dynamics codes and examples of their use are shown. However, the complexity of these codes, the difficulty in establishing boundary conditions, their cost and computational demands limit their usability in solving day-to-day production problems.A simplified, web-based model of a furnace atmosphere is described where the conservation equations are solved to determine the composition profiles of the atmosphere in the furnace. Although the model is restricted in scope to certain types of furnace, it is shown to give better results than CFD when boundary conditions are uncertain. The application of the model to the understanding of existing furnace conditions and to determining ways of optimising the use of gases are discussed. IntroductionThe important role of protective atmospheres during heat treatment of metals, furnace brazing of assemblies and soldering of printed circuit boards is well established. The atmosphere in the furnace prevents air ingress and oxidation of the parts, helps flush away any flux or binder from braze and solder pastes and provides an important mode of heat transfer [1]. In a batch furnace having typically one or two gas injectors, the gas utilisation and process can be optimised by minimising air leaks and mantaining atmosphere homogeneity with fans or other atmosphere circulation techniques. In a continuous furnace, however, atmosphere optimisation is more difficult as furnace inlets and exits can also let in air. The atmosphere requirements of different stages of heat treatment, brazing or soldering vary [2]. Achieving these atmospheres in different sections of the open-ended furnace is a relatively complex task. Methods such as atmosphere zoning and the use of physical curtains and gas injectors have evolved with time, though it is hard to predict how effective these techniques will be for a given furnace and process. Experts in the field tend to rely on experience and rules-of-thumb rather than scientific method to achieve the required results."

Jan 1, 2001

By Claudio Parra De Lazzari

The determination of the governing step of the deoxidation rate and the effects of the hydrogen content of the mixtures (C), the diameter of the delivery orifice (4) and the Reynolds number of the orifice (Re.) on the product Av kjg were investigated. A,, is the total surface area of the interface between the bubbles and the melt and kjg is the mass transfer coefficient in the gas phase. The design of the experiments was based on a two level statistically fractionated, factorial planning. Oxygen in the melt was measured as a function of time. It was found that the governing step of the deoxidation rate was the transport of hydrogen in the gaseous phase and that {Ay kjg} increases with C, {o} and Reo.

Jan 1, 1997

By R. J. Dippenaar, W. H. Van Niekerk

"An injectable lime-based desulphurization reagent for the treatment of liquid iron was developed. Firstly, selected lime based slags containing small quantities of CaF2 to increase fluidity, and Na20 to increase the basicity, have been evaluated on laboratory scale from a thermodynamic point of view. Subsequently, pilot plant and full scale industrial injection trials were conducted. It was found that lime-based slags, containing Na20 and CaF2, are able to desulphurize liquid iron efficiently. By the injection of a lime based reagent consisting of 60% lime, 25% soda ash and 15% fluorspar at a rate of 7 kg reagent/ton hot metal, the sulphur level in the metal (115kg) was reduced from 0,07% to 0,01 % within 5 minutes. The lime-based reagent developed in this study was successfully injected, both from a metallurgical and from a pneumatic point of view, on an industrial scale. The mathematical model utilised in this study, can be used successfully to predict the course and extent of desulphurization by lime-based slags. IntroductionMainly due to environmental difficulties encountered with pure soda ash, dry slag formation with CaC2 and high cost when Mg are used as desulphurizers, much incentive exists for the development of an inexpensive, environmentally friendlier desulphurization reagent. As a first step in the development of such a reagent, selected lime based slags containing small quantities of CaF2 to increase fluidity, and Na2O to increase the basicity, have been evaluated on laboratory scale from a thermodynamic point of view. This was followed by pilot plant injection experiments in which the kinetics of the relevant desulphurization reactions were evaluated. Finally, full scale industrial trials were conducted. All three phases of the investigation will be discussed with the major emphasis being placed on the kinetic study."

Jan 1, 1996

By Yousef Mohassab, Hong Yong Sohn, Mohamed Elzohiery

As part of the development of a novel flash ironmaking process at the University of Utah, a labscale flash reactor was used to produce iron directly from iron oxide concentrate. This work tested the feasibility of the novel flash ironmaking process using the partial combustion of hydrogen as fuel and reductant. In this flash reactor, the energy required to reduce concentrate particles was obtained from the internal combustion of hydrogen and oxygen with complementary energy from electrical resistance heating to compensate for the heat loss. After the reaction shaft was electrically pre-heated, hydrogen and oxygen streams produced a non-premixed flame inside the reaction shaft. Various conditions such as flame configuration, flame power, positions of concentrate feeding ports, excess hydrogen amount and residence time were tested. More than 90% reduction of magnetite or hematite was achieved at temperatures as low as 1175 oC with < 100% excess hydrogen in <10 s of residence time.

Jan 1, 2016

By M. A. Neri

A lead-free solder alloy Sn-57.5Bi-0.5Ag has been developed by mechanical alloying and foundry processes, and has great potential as a lead-free solder system, to low temperature applications. The mechanical alloying powders show a microstructure different to the microstructure obtained by the foundry process for the same alloy. Its melting point of 142°C is slightly higher than that of eutectic tin- bismuth solder. Examination of the microstructure revealed that eutectic microstructure is refined by the mechanical alloying process Ag additions. The lamellar structure of tin-bismuth gradually disappeared with the process of mechanical alloying, while intermetallic compounds AgaSn phase was formed. The Cu-Sn intermetallic compound layer formed at solder-copper interface is the Cu6Sn5 phase. Keywords: Lead-free solder, Microstructure. Mechanical alloying

Jan 1, 2003

By Y. Z. Zhang

Electrochemical oxidation of arsenopyrite in ferric sulphate media in the absence and presence of bacteria T jerrooxidans has been investigated for the purpose of understanding the dissolution chemistry of arsenopyrite and the bacteria attack mechanism. Mixed potential, polarization resistance measurements, polarization curve, cyclic voltammetry experiments were conducted in a ferric sulphate medium of 10g/L FeH, temp.25-35°C, pH 1.5-2.5 in the absence and presence of bacteria Tjerrooxidans, respectively. For the anodic process, a two-step reaction sequence is suggested by the electrochemical measurements. The initial step at a low potential is described by:

Jan 1, 1996

By Zhang Libo, Li Wei, Peng Jinhui, Guo Shenghui, L. Jing

Partially stabilized zirconia ceramics (PSZ) were prepared by microwave sintering using natural baddeleyite which was obtained by flotation of baddeleyite ore as starting materials. Because of using natural baddeleyite as raw and the process producing no waste, it realized shorter process, energy savmg, environmentally-friendly and non-damage processing. In this work natural baddeleyite stabilized with 3.8wt.% CaO were sintered at 1300°C for 60min in a multi-mode 2.45GHz microwave furnace. Microwave sintering could fast heating and sintering. Besides that, microwave sintering could heat materials wholly, low the sintering temperature, improve the materials properties and save energy. X-ray spectrum displayed the product composed by the tetragonal phase and monoclinic phase that also showed the product was PSZ. Fine and uniform microstructures were observed in the product through scanning electron microscopy. PSZ which was with high density was confirmed by the method of the Archimedes technique.

Jan 1, 2011