Search Documents

By E. W. Coderre, R. C. Baxter

"This paper describes the townsite of Wabush and the two railways operated by Wabush Mines for the loading and unloading of iron ore concentrate. The town of Wabush is located approximately 200 air miles north of Sept-Iles, Quebec and is in the Province of Newfoundland and Labrador. Construction of the town-site began in 1961 to provide housing accommodation for the construction force and permanent employees in the mining and milling operations located 4 miles away. Wabush Mines operates two short railway lines in loading and unloading concentrate between the concentrator, located at Wabush, and the pellet plant at Pointe Noire, Quebec. Both of these railways connect with the main line of the Quebec North Shore and Labrador Railway and provide a shuttle service between the two phases of the operation."

Jan 1, 1969

The negative effects of pyrite and pyrrhotite on thiosulfate gold leaching have been investigated. Possible remedies to reduce some problems are discussed. In a gold bearing pure silicate ore, 92% of gold could be extracted within 3 hours using a solution containing 0.2 mol/L ammonium thiosulfate, 0.9 mol/L ammonia, 30 - 300 ppm copper sulfate and 8.6 ppm dissolved oxygen at pH 10.26. The thiosulfate consumption was 7.1 kg/t under these conditions and could be further reduced to 3.5 kg/t by decreasing the dissolved oxygen to 0.3 ppm. Addition of 16% pyrrhotite or pyrite into the silicate slurry led to a decrease in gold extraction by 2% or 9% respectively and an increase of thiosulfate consumption by 11 kg/t or12.8 kg/t respectively in three hours. Several adjustments, such as increasing copper ion and ammonia concentration and reducing the dissolved oxygen level to 0.3 ppm resulted in increased gold extraction and lower thiosulfate consumption despite the presence of these sulfides.

Jan 1, 2005

By Kevin P. Plucknett, Z. Memarrashidi

"In the current work, factors influencing the corrosion mechanisms of TiC and Ti(C,N) based cermets are reviewed. Cermets were typically prepared with 30 vol.% of metal binder, in the form of various in-situ reaction-formed Ni3Al alloys. Commercial WC-Co hardmetals were also examined as baseline materials. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential and potentiodynamic polarisation. The corrosion potential and current density were determined, following Tafel extrapolation, allowing estimation of the corrosion rates. Post-corrosion characterisation involved scanning electron microscopy analysis and associated energy dispersive X-ray spectroscopy of the sample surfaces. It is demonstrated that the primary corrosion mechanism for this type of cermet is dissolution of the metallic phase during oxidation attack, and thus this response can be expected to increase with the amount of binder in the cermet, although degradation can be subtly affected by composition (i.e. alloy composition, C:N ratio, impurities in the ceramic phase, etc.) and test procedure (i.e. aerated vs. de-aerated electrolytes). It was observed that addition of N content into the ceramic phase is beneficial to the corrosion characteristics of TiC based cermets, through significant refinement in the grain size of the hard phase. Similarly, elimination of impurities, such as W in selected TiC powders, also improves the corrosion resistance.INTRODUCTION Cermets are prepared using the combination of a hard, high elastic modulus ceramic phase with a ductile, high toughness metallic binder. This pairing of hard and ductile components ensures wide application of cermets in demanding wear environments. These materials are consequently used industrially in both bulk and coating form. The most common example of such a composite system is based on the use of tungsten carbide with a cobalt-based binder (WC-Co), which has been widely examined over the past 80 years. However, while WC-Co has been shown to exhibit an excellent combination of high strength and wear resistance, the corrosion and high temperature properties of this material are relatively poor. In addition, WC-Co possesses a high density (~13–14 g/cm3), which makes it a less desirable option when the component mass is a design factor (i.e. use in aerospace). In particular, the aqueous corrosion response of WC-Co limits its use in wear environments where combined corrosive degradation may occur (i.e. tribo-corrosion scenarios). Alternate cermet systems are therefore being actively developed due to these performance limitations."

Jan 1, 2017

By F. Ford, Z. Dai, A. W. Lee

ABSTRACT: As high-grade nickel sulphide ores are being depleted and processing laterite ores continues to pose challenges, the future of nickel extraction lies in low-grade ultramafic ores. Canada has large resources of low-grade ultramafic nickel sulphide ores in the Thompson Nickel Belt. Most of the deposits are high tonnage and open pittable, but have high MgO content. The main challenge in processing low-grade ultramafic ores is the presence of serpentine. Chrysotile, one of the three polymorphs of serpentine, is the most common form of asbestos. In addition, the high slurry viscosity associated with ultramafic ores makes grinding and flotation possible only at a very low solids percentage.

Jan 1, 2011

By W. G. Mine

In September, 1953, seismographs were installed in the Crowsnest Pass area of Alberta and British Columbia to study the 'bumps' which were occurring in the coal mines at Fernie and Coleman, and to investigate the possibility that they might be related to minor earthquakes in the area. During the initial phase of the work, three seismographs were operated at widely separated stations, two in the region of coal mines at Coal Creek and Coleman and one at Turner Valley, distant from any mining operations. Some earthquakes were recorded at all three stations and, in addition, many small disturbances were recorded by the seismographs located near the mines, especially -by the instrument at Goal Greek. A closer network of radio-linked seismographs was then in-stalled near Fernie, the records of which definitely established that the small disturbances were occurring in the mine workings, both active and inactive. No relationship was established between bumps and local earth-quakes in the area. This work was initiated as a -co-operative effort with the Fuels Di-vision of the Mines Branch, Department of Mines and Technical Surveys, which has undertaken a study into the phenomena of ground stress relief in underground mine workings.

Jan 1, 1958

By G. R. Webber

CHEMICAL AN AL YSIS by x-ray emission spectrometry has become increasingly important during the past few years. The method is analogous to optical spectrography ?with x-rays being used instead of light and should not be confused with methods of x-ray diffraction used? for identification of minerals and chemical compounds. X-ray emission spectrometry has many advantages for both qualitative and quantitative analysis. Its optimum concentration range is higher than that of the optical spectrograph, and the group of elements which can be detected is not identical to that which can be detected by the optical spectrograph. Elements which can be detected by the x-ray spectrometer are those elements from magnesium (atomic number 12) to uranium (atomic number 92) in the periodic table. The lightest elements in this range have low sensitivities and more specialized equipment is necessary for their detection than for the heavier elements. A large number of applications of x-ray analysis have been directed toward the analysis of ores, metallurgical products, and related materials (see References at end of paper). A more complete bibliography is presented in the Norelco Reporter, Vol. 3, 1956, pp. 37-39. The periodicals Analytical Chemistry and Applied Spectroscopy are a good source of current articles and references.

Jan 1, 1957

By Charles Amoah

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By C. E. St. Denis

"Training Program at Sherritt Gordon's Ruttar:. ConcentratorA formal training program for mill operators is being developed and employed at Sherritt Gordon's Ruttan Concentrator. The program was set up to fulfil the needs created by a shortage of skilled reliable labour, a 200% turnover of personnel within the first six months of operation and the rapid advances in mineral processing technology. All new employees are introduced into the Mill Department through an orientation program designed to familiarize them with the operation of the plant. All training and orientation of new employees is the responsibility of a. small training section consisting of two training foremen and one assistant. Using a combination of classroom and supervised on the job training, the training times have been cut by at least one half. High operating standards have been set and are maintained through the use of detailed manuals for each work area and competent instruction at all operating levels. The major portion of training costs arise from the salaries of the training staff but are negligible when compared to the improved recoveries, smaller turnover and less downtime. Government assistance is available to all industrial employers to offset the costs of training employees."

Jan 1, 1974

By Charles Tkaczuk

In order to remain competitive the mining industry must keep up with changes in technology. Many innovative technologies from the mining perspective are commonplace in other industries. A ?Global? review of technologies will often reveal existing technologies that can be innovatively applied in the mining industry. Industries, which are rife with proven solutions include, medicine, biotechnology, security, manufacturing, telecommunications, etc. This paper addresses the communications aspect of mining where greater productivity, lower costs and the ability to quickly react to mining related events is obtained through an increase in remote monitoring and operating control. A review of the communications systems in place globally reveals technologies that, with minimal modification, can be immediately applied to the mining environment. We discuss the concept, advantages and implementation of existing communications technology from an industry that is not usually associated with the mining industry. This technology will form the basis of a solid platform on which can be built a state-of-the-art process monitoring, control, and communication system. This lays the groundwork for providing one solution to the underground mining industry?s most difficult problem, establishing a reliable, maintainable and cost-effective underground bi-directional wired/wireless data, video and analog communications system. We need look no further than our own doorsteps to find such a solution. The cable that you see coming from the simple green or brown box on the boulevard into your home contains hundreds of television broadcast channels, FM radio channels and data channels. And if you have a set-top box, you are in control of it all. The Cable Television Broadcast Distribution System suppliers of today are at the leading edge of converging all the different methods of communications onto a common carrier, coaxial cable or fibre optic cable. There is no fundamental difference between providing a reliable communications network to a city/neighbourhood/home/personal computer than there is to a mining operation/underground level/equipment or person. The principle is the same. Only the application is different. Realizing this, we can capitalize on the efforts of other industrial sectors, to solve our communications problem. Where else can you find a solution to a problem that is mature, having been developed with the input of thousands of engineers, and having hundreds of millions of dollars spent on research and development, manufacturing, distribution, global presence and engineering support?

May 1, 2003

By O. A. Ojo, N. Esmaeili

"The effects of brazing and use of composite powder mixture as interlayer material on hot corrosion resistance of brazed IN738 superalloy were studied. Brazing was observed to result in significant reduction in the hot corrosion resistance of the superalloy. However, application of composite powder mixture, which consists of additive superalloy powder, enhanced the hot corrosion resistance of brazed samples. It is also found that although the use of composite powder mixture increased hot corrosion resistance of brazed alloy, if the additive powder completely melts, which is possible during brazing, it can significantly reduce the hot corrosion resistance of the brazed joint. Elemental micro-segregation during solidification of the joint with completely melted powder mixture produces chromium depleted zones and consequently reduces hot corrosion resistance, since a uniform distribution and adequate chromium concentration is necessary to combat hot corrosion. This has not been previously reported in the literature and it is crucial to the use of composite powder mixture for enhancing the properties of brazed superalloys.INTRODUCTION Superalloys have been developed in response to the increasing demand for materials with higher resistance to corrosion and creep and also with higher mechanical strength at higher temperatures (Smith, 1981). Ni-base superalloys are predominantly used in manufacturing hot sections of gas turbine engine components. This is due to their high strength and corrosion resistance in extremely high temperature service environments which is typical for hot sections of gas turbine engines (Miglietti, 2009). The continuous demand for higher efficiency and output has resulted in the use of higher operating temperatures and gas pressure in modern gas turbine engines (Jahnke & Demny, 1983). Consequently, this has caused thermal and mechanical stresses which result in severe degradation and damage of gas turbine engine components due to creep, fatigue and hot corrosion (Zhang, Feng, & He, 2006). The decision to replace or repair damaged parts depends on the overall repair cost and expected life of the repaired components (Jahnke & Demny, 1983). However, in most cases, it is more cost effective to repair damaged parts rather than use a full replacement."

Jan 1, 2017

By G. McIsaac

"This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone’s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place.Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. “Whatif” scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan."

Jan 1, 2005

By G. McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. ?Whatif? scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

Sep 1, 2005

By W. Curlook, L. M. Pidgeon

THE PURPOSE of this investigation was to study part of the ternary system Co-Fe-S. Jensen ( 1) established the solubility limits of sulphur in pyrrhotite. The compound with 61.7 per cent Fe, corresponding to a formula Fe12S13, was found to melt congruently at l,192°C. Hulsmann and Weibke(2) determined the Co-S phase diagram from O to 35.2 per cent S. The solubility limits of sulphur in the com-pound Co(l-x)S were not determined. The initial object of the present in-vestigation was to determine the composition at which the compound Coci-xiS melted congruently. Once this was ascertained, it was decided to investigate the ternary system Co-Fe-S from the region of 100 per cent Co(1-x) S to the region of 100 per cent Fe12S13.

Jan 1, 1953

By R. P. Townsend

It is a widely accepted "fact" that a Koepe friction hoist is generally the best solution for production hoisting when compared to a double drum hoists. This would appear to be true if one looks at the initial capital cost of just the hoist, and also if one compares the size of the motors selected for the duty. But is this the whole story? What are the longer term costs involved in the hoist's operation, and what are the relative efficiency's of the two designs? Perhaps the Koepe hoist design enjoys a better reputation than it deserves.

Jan 1, 2011

By Rolf A. Knopp

This paper discusses how design differences in FLP diesel equipment in underground coal mines came about. "Design standards" tend to create differences between countries while fostering uniformity among products of competing manufacturers. "Performance requirements," on the other hand, tend to eliminate differences between countries while encouraging competitive development of better products. Examples of regulations from the U.S., Canada. Great Britain. Australia. South Africa, etc., are used to illustrate differences in the design and certification of diesel equipment for underground coal mines.

Jan 1, 1978

By G. B. Bell

"INTRODUCTION On February 1, 1962, after five years of exploration and research, Jones & Laughlin Steel Corporation announced that they would develop the Adams Mine. Plant construction began immediately and in December of 1964 the first shipment of pellets arrived at J & L's blast furnaces in Pittsburgh. J & L continued to operate the property through its wholly owned subsidiary, Jones & Laughlin Mining Company, Ltd., until August of 1971 when it was sold to Dominion Foundries and Steel, Limited of Hamilton. Dofasco engaged Cliffs of Canada, a subsidiary of Cleveland Cliffs Iron Company, to manage the operation of the property.SUMMARY:The Adams Mine is a one million tons per year iron ore pellet operation located in the Boston Township Iron Range, approximately seven miles southeast of Kirkland Lake, Ontario. The property includes 5,300 acres in which eight areas suitable for open pit mining have been outlined. It was estimated that the reserves in these out lined areas are sufficient to produce 30 million tons of high grade iron ore pellets.The ore 'consists of fine grained magnetite with alternating layers of chert and is mined by conventional open pit methods. This extremely hard and abrasive ore averages about 20 percent magnetic iron, and has a ratio of concentration of 3. 9 /1. Presently, mining operations are confined to two pits with a third one being developed for operations to begin in 1973.The run-of-mine ore is crushed and ground and then concentrated by magnetic separation and flotation to a concentrate grade of 68 percent magnetic iron. The concentrate is agglomerated by a grate-kiln pelletizing process and shipped by rail to Dofasco's blast furnaces in Hamilton and to Jones & Laughlin's furnaces in Pittsburgh."

Jan 1, 1973

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Abstract-Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-chalcopyrite core - interlayered pyrite-sphalerite-galena (Pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyrite­ quartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone 1) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (Il and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone 1, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F1 fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By E. J. Marcotte

"INCO LIMITED'S Shebandowan Mine and Mill is located in a scenic tourist and cottage area near the western tip of Lower Shebandowan Lake, approximately 90 Km west of Thunder Bay, Ontario. This nicely designed complex is a positive indication that mining operations can co-exist in harmony within the natural environment.The Shebandowan complex processed nickel-copper ore from 1973 to 1985, inclusive, after which operations were shut down.In late 1988, INCO LIMITED decided to place the Shebandowan complex back into operation, under contract, to mine and mill the remainder of the ore body, according to their specifications. MaclSAAC'S EXPLORATIONS was the successful bidder for the project. Following preliminary rehabilitation, operations were re-activated in late March, 1989. The ore mined to date is of a moderately lower nickel grade than the majority of previous years. However, a higher tonnage rate, combined with improved nickel recoveries, has contributed to a viable operation.A series of mill operating and equipment modifications has enabled MaclSAAC EXPLORATIONS to achieve the quality and grade of nickel-copper concentrates specified, and at the same time, expand mill tonnage throughput while attaining increased nickel recovenes."

Jan 1, 1992

By J. Z. Cui

In this paper a statistical multi-scale method for the mechanics parameter prediction of the rock mass with random distribution of multi-scale cracks/joints is presented. First the micro-structure of the rock mass with random distribution of multi-scale cracks/joints is represented. Then the statistical second-order two-scale method for the mechanics performance predictions of the rock mass structure with random cracks/joints distribution is presented, including the statistical second-order two-scale expression on the vector-valued displacement, strain tensor and stress tensor, and the algorithm procedure of statistical multi-sale computation for the mechanics parameters. Finally some numerical results for mechanical parameters for the rock mass with random distributions of multi-scale joints/cracks by statistical multi-scale method are shown.

May 1, 2009

By W. A. Gow, J. A. Vezina

"A new process for treating scheelite for the production of tungstic tri-oxide is described. The novelty of the process resides in that an ion-ex-changer is used to convert sodium tungstate to either ammonium tung-state or tungstic acid.The process consists of a conventional hydrochloric acid leach of the scheelite concentrate, and the dissolution of the impure tungstic acid thus produced with sodium hydroxide at pH 8. The sodium tungstate solution is clarified and passed through a column of Dowex 50Wx8 ion-ex-change resin to exchange the sodium ions for either hydrogen or ammonium ions, both being suitable. The tungsten-bearing column effluent is evaporated to crystallize the tungsten as ammonium tungstate; the crystals are washed with nitric acid and water and decomposed by heat to pro-duce tungstic trioxide of high purity.Ninety-six per cent of the tungsten in the concentrate may be re-covered as tungs tic trioxide (W03), and the reagents consumed are 0.7 g HCl, 0.41 g NaOH and either 1.73 g NH.Cl or 225 g HCl per gram of tungsten."

Jan 1, 1966